cregit-Linux how code gets into the kernel

Release 4.10 drivers/ata/pata_artop.c

Directory: drivers/ata
/*
 *    pata_artop.c - ARTOP ATA controller driver
 *
 *      (C) 2006 Red Hat
 *      (C) 2007,2011 Bartlomiej Zolnierkiewicz
 *
 *    Based in part on drivers/ide/pci/aec62xx.c
 *      Copyright (C) 1999-2002 Andre Hedrick <andre@linux-ide.org>
 *      865/865R fixes for Macintosh card version from a patch to the old
 *              driver by Thibaut VARENE <varenet@parisc-linux.org>
 *      When setting the PCI latency we must set 0x80 or higher for burst
 *              performance Alessandro Zummo <alessandro.zummo@towertech.it>
 *
 *      TODO
 *      Investigate no_dsc on 850R
 *      Clock detect
 */

#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/device.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#include <linux/ata.h>


#define DRV_NAME	"pata_artop"

#define DRV_VERSION	"0.4.6"

/*
 *      The ARTOP has 33 Mhz and "over clocked" timing tables. Until we
 *      get PCI bus speed functionality we leave this as 0. Its a variable
 *      for when we get the functionality and also for folks wanting to
 *      test stuff.
 */


static int clock = 0;

/**
 *      artop62x0_pre_reset     -       probe begin
 *      @link: link
 *      @deadline: deadline jiffies for the operation
 *
 *      Nothing complicated needed here.
 */


static int artop62x0_pre_reset(struct ata_link *link, unsigned long deadline) { static const struct pci_bits artop_enable_bits[] = { { 0x4AU, 1U, 0x02UL, 0x02UL }, /* port 0 */ { 0x4AU, 1U, 0x04UL, 0x04UL }, /* port 1 */ }; struct ata_port *ap = link->ap; struct pci_dev *pdev = to_pci_dev(ap->host->dev); /* Odd numbered device ids are the units with enable bits. */ if ((pdev->device & 1) && !pci_test_config_bits(pdev, &artop_enable_bits[ap->port_no])) return -ENOENT; return ata_sff_prereset(link, deadline); }

Contributors

PersonTokensPropCommitsCommitProp
jeff garzikjeff garzik8377.57%333.33%
tejun heotejun heo1715.89%333.33%
jean delvarejean delvare32.80%111.11%
bartlomiej zolnierkiewiczbartlomiej zolnierkiewicz21.87%111.11%
alan coxalan cox21.87%111.11%
Total107100.00%9100.00%

/** * artop6260_cable_detect - identify cable type * @ap: Port * * Identify the cable type for the ARTOP interface in question */
static int artop6260_cable_detect(struct ata_port *ap) { struct pci_dev *pdev = to_pci_dev(ap->host->dev); u8 tmp; pci_read_config_byte(pdev, 0x49, &tmp); if (tmp & (1 << ap->port_no)) return ATA_CBL_PATA40; return ATA_CBL_PATA80; }

Contributors

PersonTokensPropCommitsCommitProp
jeff garzikjeff garzik5598.21%266.67%
alexey dobriyanalexey dobriyan11.79%133.33%
Total56100.00%3100.00%

/** * artop6210_load_piomode - Load a set of PATA PIO timings * @ap: Port whose timings we are configuring * @adev: Device * @pio: PIO mode * * Set PIO mode for device, in host controller PCI config space. This * is used both to set PIO timings in PIO mode and also to set the * matching PIO clocking for UDMA, as well as the MWDMA timings. * * LOCKING: * None (inherited from caller). */
static void artop6210_load_piomode(struct ata_port *ap, struct ata_device *adev, unsigned int pio) { struct pci_dev *pdev = to_pci_dev(ap->host->dev); int dn = adev->devno + 2 * ap->port_no; const u16 timing[2][5] = { { 0x0000, 0x000A, 0x0008, 0x0303, 0x0301 }, { 0x0700, 0x070A, 0x0708, 0x0403, 0x0401 } }; /* Load the PIO timing active/recovery bits */ pci_write_config_word(pdev, 0x40 + 2 * dn, timing[clock][pio]); }

Contributors

PersonTokensPropCommitsCommitProp
jeff garzikjeff garzik103100.00%1100.00%
Total103100.00%1100.00%

/** * artop6210_set_piomode - Initialize host controller PATA PIO timings * @ap: Port whose timings we are configuring * @adev: Device we are configuring * * Set PIO mode for device, in host controller PCI config space. For * ARTOP we must also clear the UDMA bits if we are not doing UDMA. In * the event UDMA is used the later call to set_dmamode will set the * bits as required. * * LOCKING: * None (inherited from caller). */
static void artop6210_set_piomode(struct ata_port *ap, struct ata_device *adev) { struct pci_dev *pdev = to_pci_dev(ap->host->dev); int dn = adev->devno + 2 * ap->port_no; u8 ultra; artop6210_load_piomode(ap, adev, adev->pio_mode - XFER_PIO_0); /* Clear the UDMA mode bits (set_dmamode will redo this if needed) */ pci_read_config_byte(pdev, 0x54, &ultra); ultra &= ~(3 << (2 * dn)); pci_write_config_byte(pdev, 0x54, ultra); }

Contributors

PersonTokensPropCommitsCommitProp
jeff garzikjeff garzik92100.00%1100.00%
Total92100.00%1100.00%

/** * artop6260_load_piomode - Initialize host controller PATA PIO timings * @ap: Port whose timings we are configuring * @adev: Device we are configuring * @pio: PIO mode * * Set PIO mode for device, in host controller PCI config space. The * ARTOP6260 and relatives store the timing data differently. * * LOCKING: * None (inherited from caller). */
static void artop6260_load_piomode (struct ata_port *ap, struct ata_device *adev, unsigned int pio) { struct pci_dev *pdev = to_pci_dev(ap->host->dev); int dn = adev->devno + 2 * ap->port_no; const u8 timing[2][5] = { { 0x00, 0x0A, 0x08, 0x33, 0x31 }, { 0x70, 0x7A, 0x78, 0x43, 0x41 } }; /* Load the PIO timing active/recovery bits */ pci_write_config_byte(pdev, 0x40 + dn, timing[clock][pio]); }

Contributors

PersonTokensPropCommitsCommitProp
jeff garzikjeff garzik101100.00%1100.00%
Total101100.00%1100.00%

/** * artop6260_set_piomode - Initialize host controller PATA PIO timings * @ap: Port whose timings we are configuring * @adev: Device we are configuring * * Set PIO mode for device, in host controller PCI config space. For * ARTOP we must also clear the UDMA bits if we are not doing UDMA. In * the event UDMA is used the later call to set_dmamode will set the * bits as required. * * LOCKING: * None (inherited from caller). */
static void artop6260_set_piomode(struct ata_port *ap, struct ata_device *adev) { struct pci_dev *pdev = to_pci_dev(ap->host->dev); u8 ultra; artop6260_load_piomode(ap, adev, adev->pio_mode - XFER_PIO_0); /* Clear the UDMA mode bits (set_dmamode will redo this if needed) */ pci_read_config_byte(pdev, 0x44 + ap->port_no, &ultra); ultra &= ~(7 << (4 * adev->devno)); /* One nibble per drive */ pci_write_config_byte(pdev, 0x44 + ap->port_no, ultra); }

Contributors

PersonTokensPropCommitsCommitProp
jeff garzikjeff garzik90100.00%1100.00%
Total90100.00%1100.00%

/** * artop6210_set_dmamode - Initialize host controller PATA PIO timings * @ap: Port whose timings we are configuring * @adev: Device whose timings we are configuring * * Set DMA mode for device, in host controller PCI config space. * * LOCKING: * None (inherited from caller). */
static void artop6210_set_dmamode (struct ata_port *ap, struct ata_device *adev) { unsigned int pio; struct pci_dev *pdev = to_pci_dev(ap->host->dev); int dn = adev->devno + 2 * ap->port_no; u8 ultra; if (adev->dma_mode == XFER_MW_DMA_0) pio = 1; else pio = 4; /* Load the PIO timing active/recovery bits */ artop6210_load_piomode(ap, adev, pio); pci_read_config_byte(pdev, 0x54, &ultra); ultra &= ~(3 << (2 * dn)); /* Add ultra DMA bits if in UDMA mode */ if (adev->dma_mode >= XFER_UDMA_0) { u8 mode = (adev->dma_mode - XFER_UDMA_0) + 1 - clock; if (mode == 0) mode = 1; ultra |= (mode << (2 * dn)); } pci_write_config_byte(pdev, 0x54, ultra); }

Contributors

PersonTokensPropCommitsCommitProp
jeff garzikjeff garzik157100.00%1100.00%
Total157100.00%1100.00%

/** * artop6260_set_dmamode - Initialize host controller PATA PIO timings * @ap: Port whose timings we are configuring * @adev: Device we are configuring * * Set DMA mode for device, in host controller PCI config space. The * ARTOP6260 and relatives store the timing data differently. * * LOCKING: * None (inherited from caller). */
static void artop6260_set_dmamode (struct ata_port *ap, struct ata_device *adev) { unsigned int pio = adev->pio_mode - XFER_PIO_0; struct pci_dev *pdev = to_pci_dev(ap->host->dev); u8 ultra; if (adev->dma_mode == XFER_MW_DMA_0) pio = 1; else pio = 4; /* Load the PIO timing active/recovery bits */ artop6260_load_piomode(ap, adev, pio); /* Add ultra DMA bits if in UDMA mode */ pci_read_config_byte(pdev, 0x44 + ap->port_no, &ultra); ultra &= ~(7 << (4 * adev->devno)); /* One nibble per drive */ if (adev->dma_mode >= XFER_UDMA_0) { u8 mode = adev->dma_mode - XFER_UDMA_0 + 1 - clock; if (mode == 0) mode = 1; ultra |= (mode << (4 * adev->devno)); } pci_write_config_byte(pdev, 0x44 + ap->port_no, ultra); }

Contributors

PersonTokensPropCommitsCommitProp
jeff garzikjeff garzik161100.00%1100.00%
Total161100.00%1100.00%

/** * artop_6210_qc_defer - implement serialization * @qc: command * * Issue commands per host on this chip. */
static int artop6210_qc_defer(struct ata_queued_cmd *qc) { struct ata_host *host = qc->ap->host; struct ata_port *alt = host->ports[1 ^ qc->ap->port_no]; int rc; /* First apply the usual rules */ rc = ata_std_qc_defer(qc); if (rc != 0) return rc; /* Now apply serialization rules. Only allow a command if the other channel state machine is idle */ if (alt && alt->qc_active) return ATA_DEFER_PORT; return 0; }

Contributors

PersonTokensPropCommitsCommitProp
alan coxalan cox75100.00%1100.00%
Total75100.00%1100.00%

static struct scsi_host_template artop_sht = { ATA_BMDMA_SHT(DRV_NAME), }; static struct ata_port_operations artop6210_ops = { .inherits = &ata_bmdma_port_ops, .cable_detect = ata_cable_40wire, .set_piomode = artop6210_set_piomode, .set_dmamode = artop6210_set_dmamode, .prereset = artop62x0_pre_reset, .qc_defer = artop6210_qc_defer, }; static struct ata_port_operations artop6260_ops = { .inherits = &ata_bmdma_port_ops, .cable_detect = artop6260_cable_detect, .set_piomode = artop6260_set_piomode, .set_dmamode = artop6260_set_dmamode, .prereset = artop62x0_pre_reset, };
static void atp8xx_fixup(struct pci_dev *pdev) { if (pdev->device == 0x0005) /* BIOS may have left us in UDMA, clear it before libata probe */ pci_write_config_byte(pdev, 0x54, 0); else if (pdev->device == 0x0008 || pdev->device == 0x0009) { u8 reg; /* Mac systems come up with some registers not set as we will need them */ /* Clear reset & test bits */ pci_read_config_byte(pdev, 0x49, &reg); pci_write_config_byte(pdev, 0x49, reg & ~0x30); /* PCI latency must be > 0x80 for burst mode, tweak it * if required. */ pci_read_config_byte(pdev, PCI_LATENCY_TIMER, &reg); if (reg <= 0x80) pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x90); /* Enable IRQ output and burst mode */ pci_read_config_byte(pdev, 0x4a, &reg); pci_write_config_byte(pdev, 0x4a, (reg & ~0x01) | 0x80); } }

Contributors

PersonTokensPropCommitsCommitProp
bartlomiej zolnierkiewiczbartlomiej zolnierkiewicz126100.00%1100.00%
Total126100.00%1100.00%

/** * artop_init_one - Register ARTOP ATA PCI device with kernel services * @pdev: PCI device to register * @ent: Entry in artop_pci_tbl matching with @pdev * * Called from kernel PCI layer. * * LOCKING: * Inherited from PCI layer (may sleep). * * RETURNS: * Zero on success, or -ERRNO value. */
static int artop_init_one (struct pci_dev *pdev, const struct pci_device_id *id) { static const struct ata_port_info info_6210 = { .flags = ATA_FLAG_SLAVE_POSS, .pio_mask = ATA_PIO4, .mwdma_mask = ATA_MWDMA2, .udma_mask = ATA_UDMA2, .port_ops = &artop6210_ops, }; static const struct ata_port_info info_626x = { .flags = ATA_FLAG_SLAVE_POSS, .pio_mask = ATA_PIO4, .mwdma_mask = ATA_MWDMA2, .udma_mask = ATA_UDMA4, .port_ops = &artop6260_ops, }; static const struct ata_port_info info_628x = { .flags = ATA_FLAG_SLAVE_POSS, .pio_mask = ATA_PIO4, .mwdma_mask = ATA_MWDMA2, .udma_mask = ATA_UDMA5, .port_ops = &artop6260_ops, }; static const struct ata_port_info info_628x_fast = { .flags = ATA_FLAG_SLAVE_POSS, .pio_mask = ATA_PIO4, .mwdma_mask = ATA_MWDMA2, .udma_mask = ATA_UDMA6, .port_ops = &artop6260_ops, }; const struct ata_port_info *ppi[] = { NULL, NULL }; int rc; ata_print_version_once(&pdev->dev, DRV_VERSION); rc = pcim_enable_device(pdev); if (rc) return rc; if (id->driver_data == 0) /* 6210 variant */ ppi[0] = &info_6210; else if (id->driver_data == 1) /* 6260 */ ppi[0] = &info_626x; else if (id->driver_data == 2) { /* 6280 or 6280 + fast */ unsigned long io = pci_resource_start(pdev, 4); ppi[0] = &info_628x; if (inb(io) & 0x10) ppi[0] = &info_628x_fast; } BUG_ON(ppi[0] == NULL); atp8xx_fixup(pdev); return ata_pci_bmdma_init_one(pdev, ppi, &artop_sht, NULL, 0); }

Contributors

PersonTokensPropCommitsCommitProp
jeff garzikjeff garzik20065.36%216.67%
tejun heotejun heo5417.65%541.67%
bartlomiej zolnierkiewiczbartlomiej zolnierkiewicz4113.40%216.67%
erik inge bolsoerik inge bolso82.61%18.33%
alan coxalan cox20.65%18.33%
joe perchesjoe perches10.33%18.33%
Total306100.00%12100.00%

static const struct pci_device_id artop_pci_tbl[] = { { PCI_VDEVICE(ARTOP, 0x0005), 0 }, { PCI_VDEVICE(ARTOP, 0x0006), 1 }, { PCI_VDEVICE(ARTOP, 0x0007), 1 }, { PCI_VDEVICE(ARTOP, 0x0008), 2 }, { PCI_VDEVICE(ARTOP, 0x0009), 2 }, { } /* terminate list */ }; #ifdef CONFIG_PM_SLEEP
static int atp8xx_reinit_one(struct pci_dev *pdev) { struct ata_host *host = pci_get_drvdata(pdev); int rc; rc = ata_pci_device_do_resume(pdev); if (rc) return rc; atp8xx_fixup(pdev); ata_host_resume(host); return 0; }

Contributors

PersonTokensPropCommitsCommitProp
bartlomiej zolnierkiewiczbartlomiej zolnierkiewicz5098.04%150.00%
jingoo hanjingoo han11.96%150.00%
Total51100.00%2100.00%

#endif static struct pci_driver artop_pci_driver = { .name = DRV_NAME, .id_table = artop_pci_tbl, .probe = artop_init_one, .remove = ata_pci_remove_one, #ifdef CONFIG_PM_SLEEP .suspend = ata_pci_device_suspend, .resume = atp8xx_reinit_one, #endif }; module_pci_driver(artop_pci_driver); MODULE_AUTHOR("Alan Cox, Bartlomiej Zolnierkiewicz"); MODULE_DESCRIPTION("SCSI low-level driver for ARTOP PATA"); MODULE_LICENSE("GPL"); MODULE_DEVICE_TABLE(pci, artop_pci_tbl); MODULE_VERSION(DRV_VERSION);

Overall Contributors

PersonTokensPropCommitsCommitProp
jeff garzikjeff garzik126373.95%516.13%
bartlomiej zolnierkiewiczbartlomiej zolnierkiewicz24714.46%412.90%
tejun heotejun heo905.27%1135.48%
alan coxalan cox865.04%412.90%
erik inge bolsoerik inge bolso80.47%13.23%
akira iguchiakira iguchi60.35%13.23%
jean delvarejean delvare30.18%13.23%
axel linaxel lin20.12%13.23%
jingoo hanjingoo han10.06%13.23%
alexey dobriyanalexey dobriyan10.06%13.23%
joe perchesjoe perches10.06%13.23%
Total1708100.00%31100.00%
Directory: drivers/ata
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.