Release 4.10 drivers/ata/pata_sl82c105.c

/*
 * pata_sl82c105.c      - SL82C105 PATA for new ATA layer
 *                        (C) 2005 Red Hat Inc
 *                        (C) 2011 Bartlomiej Zolnierkiewicz
 *
 * Based in part on linux/drivers/ide/pci/sl82c105.c
 *              SL82C105/Winbond 553 IDE driver
 *
 * and in part on the documentation and errata sheet
 *
 *
 * Note: The controller like many controllers has shared timings for
 * PIO and DMA. We thus flip to the DMA timings in dma_start and flip back
 * in the dma_stop function. Thus we actually don't need a set_dmamode
 * method as the PIO method is always called and will set the right PIO
 * timing parameters.
 */

#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>


#define DRV_NAME "pata_sl82c105"

#define DRV_VERSION "0.3.3"

enum {
	/*
         * SL82C105 PCI config register 0x40 bits.
         */
	
CTRL_IDE_IRQB	=	(1 << 30),
	
CTRL_IDE_IRQA   =	(1 << 28),
	
CTRL_LEGIRQ     =	(1 << 11),
	
CTRL_P1F16      =	(1 << 5),
	
CTRL_P1EN       =	(1 << 4),
	
CTRL_P0F16      =	(1 << 1),
	
CTRL_P0EN       =	(1 << 0)
};

/**
 *      sl82c105_pre_reset              -       probe begin
 *      @link: ATA link
 *      @deadline: deadline jiffies for the operation
 *
 *      Set up cable type and use generic probe init
 */



static int sl82c105_pre_reset(struct ata_link *link, unsigned long deadline)
{
	static const struct pci_bits sl82c105_enable_bits[] = {
		{ 0x40, 1, 0x01, 0x01 },
		{ 0x40, 1, 0x10, 0x10 }
	};
	struct ata_port *ap = link->ap;
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);

	if (ap->port_no && !pci_test_config_bits(pdev, &sl82c105_enable_bits[ap->port_no]))
		return -ENOENT;
	return ata_sff_prereset(link, deadline);
}


Contributors
Person
Tokens
Prop
Commits
CommitProp
jeff garzik
jeff garzik
78
78.79%
1
20.00%
tejun heo
tejun heo
19
19.19%
3
60.00%
alan cox
alan cox
2
2.02%
1
20.00%
Total
99
100.00%
5
100.00%

/**
 *      sl82c105_configure_piomode      -       set chip PIO timing
 *      @ap: ATA interface
 *      @adev: ATA device
 *      @pio: PIO mode
 *
 *      Called to do the PIO mode setup. Our timing registers are shared
 *      so a configure_dmamode call will undo any work we do here and vice
 *      versa
 */



static void sl82c105_configure_piomode(struct ata_port *ap, struct ata_device *adev, int pio)
{
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	static u16 pio_timing[5] = {
		0x50D, 0x407, 0x304, 0x242, 0x240
	};
	u16 dummy;
	int timing = 0x44 + (8 * ap->port_no) + (4 * adev->devno);

	pci_write_config_word(pdev, timing, pio_timing[pio]);
	/* Can we lose this oddity of the old driver */
	pci_read_config_word(pdev, timing, &dummy);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
jeff garzik
jeff garzik
99
100.00%
1
100.00%
Total
99
100.00%
1
100.00%

/**
 *      sl82c105_set_piomode    -       set initial PIO mode data
 *      @ap: ATA interface
 *      @adev: ATA device
 *
 *      Called to do the PIO mode setup. Our timing registers are shared
 *      but we want to set the PIO timing by default.
 */



static void sl82c105_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
	sl82c105_configure_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
jeff garzik
jeff garzik
29
100.00%
1
100.00%
Total
29
100.00%
1
100.00%

/**
 *      sl82c105_configure_dmamode      -       set DMA mode in chip
 *      @ap: ATA interface
 *      @adev: ATA device
 *
 *      Load DMA cycle times into the chip ready for a DMA transfer
 *      to occur.
 */



static void sl82c105_configure_dmamode(struct ata_port *ap, struct ata_device *adev)
{
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	static u16 dma_timing[3] = {
		0x707, 0x201, 0x200
	};
	u16 dummy;
	int timing = 0x44 + (8 * ap->port_no) + (4 * adev->devno);
	int dma = adev->dma_mode - XFER_MW_DMA_0;

	pci_write_config_word(pdev, timing, dma_timing[dma]);
	/* Can we lose this oddity of the old driver */
	pci_read_config_word(pdev, timing, &dummy);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
jeff garzik
jeff garzik
101
100.00%
1
100.00%
Total
101
100.00%
1
100.00%

/**
 *      sl82c105_reset_engine   -       Reset the DMA engine
 *      @ap: ATA interface
 *
 *      The sl82c105 has some serious problems with the DMA engine
 *      when transfers don't run as expected or ATAPI is used. The
 *      recommended fix is to reset the engine each use using a chip
 *      test register.
 */



static void sl82c105_reset_engine(struct ata_port *ap)
{
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	u16 val;

	pci_read_config_word(pdev, 0x7E, &val);
	pci_write_config_word(pdev, 0x7E, val | 4);
	pci_write_config_word(pdev, 0x7E, val & ~4);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
jeff garzik
jeff garzik
61
100.00%
1
100.00%
Total
61
100.00%
1
100.00%

/**
 *      sl82c105_bmdma_start            -       DMA engine begin
 *      @qc: ATA command
 *
 *      Reset the DMA engine each use as recommended by the errata
 *      document.
 *
 *      FIXME: if we switch clock at BMDMA start/end we might get better
 *      PIO performance on DMA capable devices.
 */



static void sl82c105_bmdma_start(struct ata_queued_cmd *qc)
{
	struct ata_port *ap = qc->ap;

	udelay(100);
	sl82c105_reset_engine(ap);
	udelay(100);

	/* Set the clocks for DMA */
	sl82c105_configure_dmamode(ap, qc->dev);
	/* Activate DMA */
	ata_bmdma_start(qc);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
jeff garzik
jeff garzik
41
80.39%
1
50.00%
olaf hering
olaf hering
10
19.61%
1
50.00%
Total
51
100.00%
2
100.00%

/**
 *      sl82c105_bmdma_end              -       DMA engine stop
 *      @qc: ATA command
 *
 *      Reset the DMA engine each use as recommended by the errata
 *      document.
 *
 *      This function is also called to turn off DMA when a timeout occurs
 *      during DMA operation. In both cases we need to reset the engine,
 *      so no actual eng_timeout handler is required.
 *
 *      We assume bmdma_stop is always called if bmdma_start as called. If
 *      not then we may need to wrap qc_issue.
 */



static void sl82c105_bmdma_stop(struct ata_queued_cmd *qc)
{
	struct ata_port *ap = qc->ap;

	ata_bmdma_stop(qc);
	sl82c105_reset_engine(ap);
	udelay(100);

	/* This will redo the initial setup of the DMA device to matching
           PIO timings */
	sl82c105_set_piomode(ap, qc->dev);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
jeff garzik
jeff garzik
39
86.67%
1
33.33%
olaf hering
olaf hering
5
11.11%
1
33.33%
alan cox
alan cox
1
2.22%
1
33.33%
Total
45
100.00%
3
100.00%

/**
 *      sl82c105_qc_defer       -       implement serialization
 *      @qc: command
 *
 *      We must issue one command per host not per channel because
 *      of the reset bug.
 *
 *      Q: is the scsi host lock sufficient ?
 */



static int sl82c105_qc_defer(struct ata_queued_cmd *qc)
{
	struct ata_host *host = qc->ap->host;
	struct ata_port *alt = host->ports[1 ^ qc->ap->port_no];
	int rc;

	/* First apply the usual rules */
	rc = ata_std_qc_defer(qc);
	if (rc != 0)
		return rc;

	/* Now apply serialization rules. Only allow a command if the
           other channel state machine is idle */
	if (alt && alt->qc_active)
		return	ATA_DEFER_PORT;
	return 0;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
alan cox
alan cox
75
100.00%
1
100.00%
Total
75
100.00%
1
100.00%



static bool sl82c105_sff_irq_check(struct ata_port *ap)
{
	struct pci_dev *pdev	= to_pci_dev(ap->host->dev);
	u32 val, mask		= ap->port_no ? CTRL_IDE_IRQB : CTRL_IDE_IRQA;

	pci_read_config_dword(pdev, 0x40, &val);

	return val & mask;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
sergei shtylyov
sergei shtylyov
53
100.00%
1
100.00%
Total
53
100.00%
1
100.00%


static struct scsi_host_template sl82c105_sht = {
	ATA_BMDMA_SHT(DRV_NAME),
};


static struct ata_port_operations sl82c105_port_ops = {
	.inherits	= &ata_bmdma_port_ops,
	.qc_defer	= sl82c105_qc_defer,
	.bmdma_start 	= sl82c105_bmdma_start,
	.bmdma_stop	= sl82c105_bmdma_stop,
	.cable_detect	= ata_cable_40wire,
	.set_piomode	= sl82c105_set_piomode,
	.prereset	= sl82c105_pre_reset,
	.sff_irq_check	= sl82c105_sff_irq_check,
};

/**
 *      sl82c105_bridge_revision        -       find bridge version
 *      @pdev: PCI device for the ATA function
 *
 *      Locates the PCI bridge associated with the ATA function and
 *      providing it is a Winbond 553 reports the revision. If it cannot
 *      find a revision or the right device it returns -1
 */



static int sl82c105_bridge_revision(struct pci_dev *pdev)
{
	struct pci_dev *bridge;

	/*
         * The bridge should be part of the same device, but function 0.
         */
	bridge = pci_get_slot(pdev->bus,
			       PCI_DEVFN(PCI_SLOT(pdev->devfn), 0));
	if (!bridge)
		return -1;

	/*
         * Make sure it is a Winbond 553 and is an ISA bridge.
         */
	if (bridge->vendor != PCI_VENDOR_ID_WINBOND ||
	    bridge->device != PCI_DEVICE_ID_WINBOND_83C553 ||
	    bridge->class >> 8 != PCI_CLASS_BRIDGE_ISA) {
	    	pci_dev_put(bridge);
		return -1;
	}
	/*
         * We need to find function 0's revision, not function 1
         */
	pci_dev_put(bridge);
	return bridge->revision;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
jeff garzik
jeff garzik
89
96.74%
1
50.00%
auke kok
auke kok
3
3.26%
1
50.00%
Total
92
100.00%
2
100.00%



static void sl82c105_fixup(struct pci_dev *pdev)
{
	u32 val;

	pci_read_config_dword(pdev, 0x40, &val);
	val |= CTRL_P0EN | CTRL_P0F16 | CTRL_P1F16;
	pci_write_config_dword(pdev, 0x40, val);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
bartlomiej zolnierkiewicz
bartlomiej zolnierkiewicz
41
100.00%
1
100.00%
Total
41
100.00%
1
100.00%



static int sl82c105_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
	static const struct ata_port_info info_dma = {
		.flags = ATA_FLAG_SLAVE_POSS,
		.pio_mask = ATA_PIO4,
		.mwdma_mask = ATA_MWDMA2,
		.port_ops = &sl82c105_port_ops
	};
	static const struct ata_port_info info_early = {
		.flags = ATA_FLAG_SLAVE_POSS,
		.pio_mask = ATA_PIO4,
		.port_ops = &sl82c105_port_ops
	};
	/* for now use only the first port */
	const struct ata_port_info *ppi[] = { &info_early,
					       NULL };
	int rev;
	int rc;

	rc = pcim_enable_device(dev);
	if (rc)
		return rc;

	rev = sl82c105_bridge_revision(dev);

	if (rev == -1)
		dev_warn(&dev->dev,
			 "pata_sl82c105: Unable to find bridge, disabling DMA\n");
	else if (rev <= 5)
		dev_warn(&dev->dev,
			 "pata_sl82c105: Early bridge revision, no DMA available\n");
	else
		ppi[0] = &info_dma;

	sl82c105_fixup(dev);

	return ata_pci_bmdma_init_one(dev, ppi, &sl82c105_sht, NULL, 0);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
jeff garzik
jeff garzik
133
76.00%
1
9.09%
tejun heo
tejun heo
31
17.71%
5
45.45%
joe perches
joe perches
4
2.29%
1
9.09%
erik inge bolso
erik inge bolso
3
1.71%
1
9.09%
alan cox
alan cox
3
1.71%
2
18.18%
bartlomiej zolnierkiewicz
bartlomiej zolnierkiewicz
1
0.57%
1
9.09%
Total
175
100.00%
11
100.00%

#ifdef CONFIG_PM_SLEEP


static int sl82c105_reinit_one(struct pci_dev *pdev)
{
	struct ata_host *host = pci_get_drvdata(pdev);
	int rc;

	rc = ata_pci_device_do_resume(pdev);
	if (rc)
		return rc;

	sl82c105_fixup(pdev);

	ata_host_resume(host);
	return 0;
}
Contributors
Person
Tokens
Prop
Commits
CommitProp
bartlomiej zolnierkiewicz
bartlomiej zolnierkiewicz
50
98.04%
1
50.00%
jingoo han
jingoo han
1
1.96%
1
50.00%
Total
51
100.00%
2
100.00%

#endif


static const struct pci_device_id sl82c105[] = {
	{ PCI_VDEVICE(WINBOND, PCI_DEVICE_ID_WINBOND_82C105), },

	{ },
};


static struct pci_driver sl82c105_pci_driver = {
	.name 		= DRV_NAME,
	.id_table	= sl82c105,
	.probe 		= sl82c105_init_one,
	.remove		= ata_pci_remove_one,
#ifdef CONFIG_PM_SLEEP
	.suspend	= ata_pci_device_suspend,
	.resume		= sl82c105_reinit_one,
#endif
};


module_pci_driver(sl82c105_pci_driver);

MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Sl82c105");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, sl82c105);

MODULE_VERSION(DRV_VERSION);
Overall Contributors
Person
Tokens
Prop
Commits
CommitProp
jeff garzik
jeff garzik
878
71.32%
4
12.90%
bartlomiej zolnierkiewicz
bartlomiej zolnierkiewicz
114
9.26%
2
6.45%
alan cox
alan cox
85
6.90%
5
16.13%
tejun heo
tejun heo
66
5.36%
12
38.71%
sergei shtylyov
sergei shtylyov
58
4.71%
1
3.23%
olaf hering
olaf hering
15
1.22%
1
3.23%
joe perches
joe perches
4
0.32%
1
3.23%
auke kok
auke kok
3
0.24%
1
3.23%
akira iguchi
akira iguchi
3
0.24%
1
3.23%
erik inge bolso
erik inge bolso
3
0.24%
1
3.23%
axel lin
axel lin
1
0.08%
1
3.23%
jingoo han
jingoo han
1
0.08%
1
3.23%
Total
1231
100.00%
31
100.00%
Directory: drivers/ata

Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.