/* * arch/arm/mach-pxa/include/mach/pcm990_baseboard.h * * (c) 2003 Phytec Messtechnik GmbH <armlinux@phytec.de> * (c) 2007 Juergen Beisert <j.beisert@pengutronix.de> * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ #include "pcm027.h" #include <mach/irqs.h> /* PXA_GPIO_TO_IRQ */ /* * definitions relevant only when the PCM-990 * development base board is in use */ /* CPLD's interrupt controller is connected to PCM-027 GPIO 9 */ #define PCM990_CTRL_INT_IRQ_GPIO 9 #define PCM990_CTRL_INT_IRQ PXA_GPIO_TO_IRQ(PCM990_CTRL_INT_IRQ_GPIO) #define PCM990_CTRL_INT_IRQ_EDGE IRQ_TYPE_EDGE_RISING #define PCM990_CTRL_PHYS PXA_CS1_PHYS /* 16-Bit */ #define PCM990_CTRL_SIZE (1*1024*1024) #define PCM990_CTRL_PWR_IRQ_GPIO 14 #define PCM990_CTRL_PWR_IRQ PXA_GPIO_TO_IRQ(PCM990_CTRL_PWR_IRQ_GPIO) #define PCM990_CTRL_PWR_IRQ_EDGE IRQ_TYPE_EDGE_RISING /* visible CPLD (U7) registers */ #define PCM990_CTRL_REG0 0x0000 /* RESET REGISTER */ #define PCM990_CTRL_SYSRES 0x0001 /* System RESET REGISTER */ #define PCM990_CTRL_RESOUT 0x0002 /* RESETOUT Enable REGISTER */ #define PCM990_CTRL_RESGPIO 0x0004 /* RESETGPIO Enable REGISTER */ #define PCM990_CTRL_REG1 0x0002 /* Power REGISTER */ #define PCM990_CTRL_5VOFF 0x0001 /* Disable 5V Regulators */ #define PCM990_CTRL_CANPWR 0x0004 /* Enable CANPWR ADUM */ #define PCM990_CTRL_PM_5V 0x0008 /* Read 5V OK */ #define PCM990_CTRL_REG2 0x0004 /* LED REGISTER */ #define PCM990_CTRL_LEDPWR 0x0001 /* POWER LED enable */ #define PCM990_CTRL_LEDBAS 0x0002 /* BASIS LED enable */ #define PCM990_CTRL_LEDUSR 0x0004 /* USER LED enable */ #define PCM990_CTRL_REG3 0x0006 /* LCD CTRL REGISTER 3 */ #define PCM990_CTRL_LCDPWR 0x0001 /* RW LCD Power on */ #define PCM990_CTRL_LCDON 0x0002 /* RW LCD Latch on */ #define PCM990_CTRL_LCDPOS1 0x0004 /* RW POS 1 */ #define PCM990_CTRL_LCDPOS2 0x0008 /* RW POS 2 */ #define PCM990_CTRL_REG4 0x0008 /* MMC1 CTRL REGISTER 4 */ #define PCM990_CTRL_MMC1PWR 0x0001 /* RW MMC1 Power on */ #define PCM990_CTRL_REG5 0x000A /* MMC2 CTRL REGISTER 5 */ #define PCM990_CTRL_MMC2PWR 0x0001 /* RW MMC2 Power on */ #define PCM990_CTRL_MMC2LED 0x0002 /* RW MMC2 LED */ #define PCM990_CTRL_MMC2DE 0x0004 /* R MMC2 Card detect */ #define PCM990_CTRL_MMC2WP 0x0008 /* R MMC2 Card write protect */ #define PCM990_CTRL_INTSETCLR 0x000C /* Interrupt Clear REGISTER */ #define PCM990_CTRL_INTC0 0x0001 /* Clear Reg BT Detect */ #define PCM990_CTRL_INTC1 0x0002 /* Clear Reg FR RI */ #define PCM990_CTRL_INTC2 0x0004 /* Clear Reg MMC1 Detect */ #define PCM990_CTRL_INTC3 0x0008 /* Clear Reg PM_5V off */ #define PCM990_CTRL_INTMSKENA 0x000E /* Interrupt Enable REGISTER */ #define PCM990_CTRL_ENAINT0 0x0001 /* Enable Int BT Detect */ #define PCM990_CTRL_ENAINT1 0x0002 /* Enable Int FR RI */ #define PCM990_CTRL_ENAINT2 0x0004 /* Enable Int MMC1 Detect */ #define PCM990_CTRL_ENAINT3 0x0008 /* Enable Int PM_5V off */ #define PCM990_CTRL_REG8 0x0014 /* Uart REGISTER */ #define PCM990_CTRL_FFSD 0x0001 /* BT Uart Enable */ #define PCM990_CTRL_BTSD 0x0002 /* FF Uart Enable */ #define PCM990_CTRL_FFRI 0x0004 /* FF Uart RI detect */ #define PCM990_CTRL_BTRX 0x0008 /* BT Uart Rx detect */ #define PCM990_CTRL_REG9 0x0010 /* AC97 Flash REGISTER */ #define PCM990_CTRL_FLWP 0x0001 /* pC Flash Write Protect */ #define PCM990_CTRL_FLDIS 0x0002 /* pC Flash Disable */ #define PCM990_CTRL_AC97ENA 0x0004 /* Enable AC97 Expansion */ #define PCM990_CTRL_REG10 0x0012 /* GPS-REGISTER */ #define PCM990_CTRL_GPSPWR 0x0004 /* GPS-Modul Power on */ #define PCM990_CTRL_GPSENA 0x0008 /* GPS-Modul Enable */ #define PCM990_CTRL_REG11 0x0014 /* Accu REGISTER */ #define PCM990_CTRL_ACENA 0x0001 /* Charge Enable */ #define PCM990_CTRL_ACSEL 0x0002 /* Charge Akku -> DC Enable */ #define PCM990_CTRL_ACPRES 0x0004 /* DC Present */ #define PCM990_CTRL_ACALARM 0x0008 /* Error Akku */ /* * IDE */ #define PCM990_IDE_IRQ_GPIO 13 #define PCM990_IDE_IRQ PXA_GPIO_TO_IRQ(PCM990_IDE_IRQ_GPIO) #define PCM990_IDE_IRQ_EDGE IRQ_TYPE_EDGE_RISING #define PCM990_IDE_PLD_PHYS 0x20000000 /* 16 bit wide */ #define PCM990_IDE_PLD_BASE 0xee000000 #define PCM990_IDE_PLD_SIZE (1*1024*1024) /* visible CPLD (U6) registers */ #define PCM990_IDE_PLD_REG0 0x1000 /* OFFSET IDE REGISTER 0 */ #define PCM990_IDE_PM5V 0x0004 /* R System VCC_5V */ #define PCM990_IDE_STBY 0x0008 /* R System StandBy */ #define PCM990_IDE_PLD_REG1 0x1002 /* OFFSET IDE REGISTER 1 */ #define PCM990_IDE_IDEMODE 0x0001 /* R TrueIDE Mode */ #define PCM990_IDE_DMAENA 0x0004 /* RW DMA Enable */ #define PCM990_IDE_DMA1_0 0x0008 /* RW 1=DREQ1 0=DREQ0 */ #define PCM990_IDE_PLD_REG2 0x1004 /* OFFSET IDE REGISTER 2 */ #define PCM990_IDE_RESENA 0x0001 /* RW IDE Reset Bit enable */ #define PCM990_IDE_RES 0x0002 /* RW IDE Reset Bit */ #define PCM990_IDE_RDY 0x0008 /* RDY */ #define PCM990_IDE_PLD_REG3 0x1006 /* OFFSET IDE REGISTER 3 */ #define PCM990_IDE_IDEOE 0x0001 /* RW Latch on Databus */ #define PCM990_IDE_IDEON 0x0002 /* RW Latch on Control Address */ #define PCM990_IDE_IDEIN 0x0004 /* RW Latch on Interrupt usw. */ #define PCM990_IDE_PLD_REG4 0x1008 /* OFFSET IDE REGISTER 4 */ #define PCM990_IDE_PWRENA 0x0001 /* RW IDE Power enable */ #define PCM990_IDE_5V 0x0002 /* R IDE Power 5V */ #define PCM990_IDE_PWG 0x0008 /* R IDE Power is on */ #define PCM990_IDE_PLD_P2V(x) ((x) - PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_BASE) #define PCM990_IDE_PLD_V2P(x) ((x) - PCM990_IDE_PLD_BASE + PCM990_IDE_PLD_PHYS) /* * Compact Flash */ #define PCM990_CF_IRQ_GPIO 11 #define PCM990_CF_IRQ PXA_GPIO_TO_IRQ(PCM990_CF_IRQ_GPIO) #define PCM990_CF_IRQ_EDGE IRQ_TYPE_EDGE_RISING #define PCM990_CF_CD_GPIO 12 #define PCM990_CF_CD PXA_GPIO_TO_IRQ(PCM990_CF_CD_GPIO) #define PCM990_CF_CD_EDGE IRQ_TYPE_EDGE_RISING #define PCM990_CF_PLD_PHYS 0x30000000 /* 16 bit wide */ /* visible CPLD (U6) registers */ #define PCM990_CF_PLD_REG0 0x1000 /* OFFSET CF REGISTER 0 */ #define PCM990_CF_REG0_LED 0x0001 /* RW LED on */ #define PCM990_CF_REG0_BLK 0x0002 /* RW LED flash when access */ #define PCM990_CF_REG0_PM5V 0x0004 /* R System VCC_5V enable */ #define PCM990_CF_REG0_STBY 0x0008 /* R System StandBy */ #define PCM990_CF_PLD_REG1 0x1002 /* OFFSET CF REGISTER 1 */ #define PCM990_CF_REG1_IDEMODE 0x0001 /* RW CF card run as TrueIDE */ #define PCM990_CF_REG1_CF0 0x0002 /* RW CF card at ADDR 0x28000000 */ #define PCM990_CF_PLD_REG2 0x1004 /* OFFSET CF REGISTER 2 */ #define PCM990_CF_REG2_RES 0x0002 /* RW CF RESET BIT */ #define PCM990_CF_REG2_RDYENA 0x0004 /* RW Enable CF_RDY */ #define PCM990_CF_REG2_RDY 0x0008 /* R CF_RDY auf PWAIT */ #define PCM990_CF_PLD_REG3 0x1006 /* OFFSET CF REGISTER 3 */ #define PCM990_CF_REG3_CFOE 0x0001 /* RW Latch on Databus */ #define PCM990_CF_REG3_CFON 0x0002 /* RW Latch on Control Address */ #define PCM990_CF_REG3_CFIN 0x0004 /* RW Latch on Interrupt usw. */ #define PCM990_CF_REG3_CFCD 0x0008 /* RW Latch on CD1/2 VS1/2 usw */ #define PCM990_CF_PLD_REG4 0x1008 /* OFFSET CF REGISTER 4 */ #define PCM990_CF_REG4_PWRENA 0x0001 /* RW CF Power on (CD1/2 = "00") */ #define PCM990_CF_REG4_5_3V 0x0002 /* RW 1 = 5V CF_VCC 0 = 3 V CF_VCC */ #define PCM990_CF_REG4_3B 0x0004 /* RW 3.0V Backup from VCC (5_3V=0) */ #define PCM990_CF_REG4_PWG 0x0008 /* R CF-Power is on */ #define PCM990_CF_PLD_REG5 0x100A /* OFFSET CF REGISTER 5 */ #define PCM990_CF_REG5_BVD1 0x0001 /* R CF /BVD1 */ #define PCM990_CF_REG5_BVD2 0x0002 /* R CF /BVD2 */ #define PCM990_CF_REG5_VS1 0x0004 /* R CF /VS1 */ #define PCM990_CF_REG5_VS2 0x0008 /* R CF /VS2 */ #define PCM990_CF_PLD_REG6 0x100C /* OFFSET CF REGISTER 6 */ #define PCM990_CF_REG6_CD1 0x0001 /* R CF Card_Detect1 */ #define PCM990_CF_REG6_CD2 0x0002 /* R CF Card_Detect2 */ /* * Wolfson AC97 Touch */ #define PCM990_AC97_IRQ_GPIO 10 #define PCM990_AC97_IRQ PXA_GPIO_TO_IRQ(PCM990_AC97_IRQ_GPIO) #define PCM990_AC97_IRQ_EDGE IRQ_TYPE_EDGE_RISING /* * MMC phyCORE */ #define PCM990_MMC0_IRQ_GPIO 9 #define PCM990_MMC0_IRQ PXA_GPIO_TO_IRQ(PCM990_MMC0_IRQ_GPIO) #define PCM990_MMC0_IRQ_EDGE IRQ_TYPE_EDGE_FALLING /* * USB phyCore */ #define PCM990_USB_OVERCURRENT (88 | GPIO_ALT_FN_1_IN) #define PCM990_USB_PWR_EN (89 | GPIO_ALT_FN_2_OUT)Overall Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| Robert Schwebel | 629 | 96.62% | 1 | 14.29% |
| Haojian Zhuang | 7 | 1.08% | 1 | 14.29% |
| Dmitry Baryshkov | 7 | 1.08% | 1 | 14.29% |
| Linus Walleij | 3 | 0.46% | 1 | 14.29% |
| Sascha Hauer | 2 | 0.31% | 1 | 14.29% |
| Arnd Bergmann | 2 | 0.31% | 1 | 14.29% |
| Russell King | 1 | 0.15% | 1 | 14.29% |
| Total | 651 | 100.00% | 7 | 100.00% |