Release 4.11 drivers/gpu/drm/bridge/sil-sii8620.h
/*
* Registers of Silicon Image SiI8620 Mobile HD Transmitter
*
* Copyright (C) 2015, Samsung Electronics Co., Ltd.
* Andrzej Hajda <a.hajda@samsung.com>
*
* Based on MHL driver for Android devices.
* Copyright (C) 2013-2014 Silicon Image, Inc.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#ifndef __SIL_SII8620_H__
#define __SIL_SII8620_H__
/* Vendor ID Low byte, default value: 0x01 */
#define REG_VND_IDL 0x0000
/* Vendor ID High byte, default value: 0x00 */
#define REG_VND_IDH 0x0001
/* Device ID Low byte, default value: 0x60 */
#define REG_DEV_IDL 0x0002
/* Device ID High byte, default value: 0x86 */
#define REG_DEV_IDH 0x0003
/* Device Revision, default value: 0x10 */
#define REG_DEV_REV 0x0004
/* OTP DBYTE510, default value: 0x00 */
#define REG_OTP_DBYTE510 0x0006
/* System Control #1, default value: 0x00 */
#define REG_SYS_CTRL1 0x0008
#define BIT_SYS_CTRL1_OTPVMUTEOVR_SET BIT(7)
#define BIT_SYS_CTRL1_VSYNCPIN BIT(6)
#define BIT_SYS_CTRL1_OTPADROPOVR_SET BIT(5)
#define BIT_SYS_CTRL1_BLOCK_DDC_BY_HPD BIT(4)
#define BIT_SYS_CTRL1_OTP2XVOVR_EN BIT(3)
#define BIT_SYS_CTRL1_OTP2XAOVR_EN BIT(2)
#define BIT_SYS_CTRL1_TX_CTRL_HDMI BIT(1)
#define BIT_SYS_CTRL1_OTPAMUTEOVR_SET BIT(0)
/* System Control DPD, default value: 0x90 */
#define REG_DPD 0x000b
#define BIT_DPD_PWRON_PLL BIT(7)
#define BIT_DPD_PDNTX12 BIT(6)
#define BIT_DPD_PDNRX12 BIT(5)
#define BIT_DPD_OSC_EN BIT(4)
#define BIT_DPD_PWRON_HSIC BIT(3)
#define BIT_DPD_PDIDCK_N BIT(2)
#define BIT_DPD_PD_MHL_CLK_N BIT(1)
/* Dual link Control, default value: 0x00 */
#define REG_DCTL 0x000d
#define BIT_DCTL_TDM_LCLK_PHASE BIT(7)
#define BIT_DCTL_HSIC_CLK_PHASE BIT(6)
#define BIT_DCTL_CTS_TCK_PHASE BIT(5)
#define BIT_DCTL_EXT_DDC_SEL BIT(4)
#define BIT_DCTL_TRANSCODE BIT(3)
#define BIT_DCTL_HSIC_RX_STROBE_PHASE BIT(2)
#define BIT_DCTL_HSIC_TX_BIST_START_SEL BIT(1)
#define BIT_DCTL_TCLKNX_PHASE BIT(0)
/* PWD Software Reset, default value: 0x20 */
#define REG_PWD_SRST 0x000e
#define BIT_PWD_SRST_COC_DOC_RST BIT(7)
#define BIT_PWD_SRST_CBUS_RST_SW BIT(6)
#define BIT_PWD_SRST_CBUS_RST_SW_EN BIT(5)
#define BIT_PWD_SRST_MHLFIFO_RST BIT(4)
#define BIT_PWD_SRST_CBUS_RST BIT(3)
#define BIT_PWD_SRST_SW_RST_AUTO BIT(2)
#define BIT_PWD_SRST_HDCP2X_SW_RST BIT(1)
#define BIT_PWD_SRST_SW_RST BIT(0)
/* AKSV_1, default value: 0x00 */
#define REG_AKSV_1 0x001d
/* Video H Resolution #1, default value: 0x00 */
#define REG_H_RESL 0x003a
/* Video Mode, default value: 0x00 */
#define REG_VID_MODE 0x004a
#define BIT_VID_MODE_M1080P BIT(6)
/* Video Input Mode, default value: 0xc0 */
#define REG_VID_OVRRD 0x0051
#define BIT_VID_OVRRD_PP_AUTO_DISABLE BIT(7)
#define BIT_VID_OVRRD_M1080P_OVRRD BIT(6)
#define BIT_VID_OVRRD_MINIVSYNC_ON BIT(5)
#define BIT_VID_OVRRD_3DCONV_EN_FRAME_PACK BIT(4)
#define BIT_VID_OVRRD_ENABLE_AUTO_PATH_EN BIT(3)
#define BIT_VID_OVRRD_ENRGB2YCBCR_OVRRD BIT(2)
#define BIT_VID_OVRRD_ENDOWNSAMPLE_OVRRD BIT(0)
/* I2C Address reassignment, default value: 0x00 */
#define REG_PAGE_MHLSPEC_ADDR 0x0057
#define REG_PAGE7_ADDR 0x0058
#define REG_PAGE8_ADDR 0x005c
/* Fast Interrupt Status, default value: 0x00 */
#define REG_FAST_INTR_STAT 0x005f
#define LEN_FAST_INTR_STAT 7
#define BIT_FAST_INTR_STAT_TIMR 8
#define BIT_FAST_INTR_STAT_INT2 9
#define BIT_FAST_INTR_STAT_DDC 10
#define BIT_FAST_INTR_STAT_SCDT 11
#define BIT_FAST_INTR_STAT_INFR 13
#define BIT_FAST_INTR_STAT_EDID 14
#define BIT_FAST_INTR_STAT_HDCP 15
#define BIT_FAST_INTR_STAT_MSC 16
#define BIT_FAST_INTR_STAT_MERR 17
#define BIT_FAST_INTR_STAT_G2WB 18
#define BIT_FAST_INTR_STAT_G2WB_ERR 19
#define BIT_FAST_INTR_STAT_DISC 28
#define BIT_FAST_INTR_STAT_BLOCK 30
#define BIT_FAST_INTR_STAT_LTRN 31
#define BIT_FAST_INTR_STAT_HDCP2 32
#define BIT_FAST_INTR_STAT_TDM 42
#define BIT_FAST_INTR_STAT_COC 51
/* GPIO Control, default value: 0x15 */
#define REG_GPIO_CTRL1 0x006e
#define BIT_CTRL1_GPIO_I_8 BIT(5)
#define BIT_CTRL1_GPIO_OEN_8 BIT(4)
#define BIT_CTRL1_GPIO_I_7 BIT(3)
#define BIT_CTRL1_GPIO_OEN_7 BIT(2)
#define BIT_CTRL1_GPIO_I_6 BIT(1)
#define BIT_CTRL1_GPIO_OEN_6 BIT(0)
/* Interrupt Control, default value: 0x06 */
#define REG_INT_CTRL 0x006f
#define BIT_INT_CTRL_SOFTWARE_WP BIT(7)
#define BIT_INT_CTRL_INTR_OD BIT(2)
#define BIT_INT_CTRL_INTR_POLARITY BIT(1)
/* Interrupt State, default value: 0x00 */
#define REG_INTR_STATE 0x0070
#define BIT_INTR_STATE_INTR_STATE BIT(0)
/* Interrupt Source #1, default value: 0x00 */
#define REG_INTR1 0x0071
/* Interrupt Source #2, default value: 0x00 */
#define REG_INTR2 0x0072
/* Interrupt Source #3, default value: 0x01 */
#define REG_INTR3 0x0073
#define BIT_DDC_CMD_DONE BIT(3)
/* Interrupt Source #5, default value: 0x00 */
#define REG_INTR5 0x0074
/* Interrupt #1 Mask, default value: 0x00 */
#define REG_INTR1_MASK 0x0075
/* Interrupt #2 Mask, default value: 0x00 */
#define REG_INTR2_MASK 0x0076
/* Interrupt #3 Mask, default value: 0x00 */
#define REG_INTR3_MASK 0x0077
/* Interrupt #5 Mask, default value: 0x00 */
#define REG_INTR5_MASK 0x0078
#define BIT_INTR_SCDT_CHANGE BIT(0)
/* Hot Plug Connection Control, default value: 0x45 */
#define REG_HPD_CTRL 0x0079
#define BIT_HPD_CTRL_HPD_DS_SIGNAL BIT(7)
#define BIT_HPD_CTRL_HPD_OUT_OD_EN BIT(6)
#define BIT_HPD_CTRL_HPD_HIGH BIT(5)
#define BIT_HPD_CTRL_HPD_OUT_OVR_EN BIT(4)
#define BIT_HPD_CTRL_GPIO_I_1 BIT(3)
#define BIT_HPD_CTRL_GPIO_OEN_1 BIT(2)
#define BIT_HPD_CTRL_GPIO_I_0 BIT(1)
#define BIT_HPD_CTRL_GPIO_OEN_0 BIT(0)
/* GPIO Control, default value: 0x55 */
#define REG_GPIO_CTRL 0x007a
#define BIT_CTRL_GPIO_I_5 BIT(7)
#define BIT_CTRL_GPIO_OEN_5 BIT(6)
#define BIT_CTRL_GPIO_I_4 BIT(5)
#define BIT_CTRL_GPIO_OEN_4 BIT(4)
#define BIT_CTRL_GPIO_I_3 BIT(3)
#define BIT_CTRL_GPIO_OEN_3 BIT(2)
#define BIT_CTRL_GPIO_I_2 BIT(1)
#define BIT_CTRL_GPIO_OEN_2 BIT(0)
/* Interrupt Source 7, default value: 0x00 */
#define REG_INTR7 0x007b
/* Interrupt Source 8, default value: 0x00 */
#define REG_INTR8 0x007c
/* Interrupt #7 Mask, default value: 0x00 */
#define REG_INTR7_MASK 0x007d
/* Interrupt #8 Mask, default value: 0x00 */
#define REG_INTR8_MASK 0x007e
#define BIT_CEA_NEW_VSI BIT(2)
#define BIT_CEA_NEW_AVI BIT(1)
/* IEEE, default value: 0x10 */
#define REG_TMDS_CCTRL 0x0080
#define BIT_TMDS_CCTRL_TMDS_OE BIT(4)
/* TMDS Control #4, default value: 0x02 */
#define REG_TMDS_CTRL4 0x0085
#define BIT_TMDS_CTRL4_SCDT_CKDT_SEL BIT(1)
#define BIT_TMDS_CTRL4_TX_EN_BY_SCDT BIT(0)
/* BIST CNTL, default value: 0x00 */
#define REG_BIST_CTRL 0x00bb
#define BIT_RXBIST_VGB_EN BIT(7)
#define BIT_TXBIST_VGB_EN BIT(6)
#define BIT_BIST_START_SEL BIT(5)
#define BIT_BIST_START_BIT BIT(4)
#define BIT_BIST_ALWAYS_ON BIT(3)
#define BIT_BIST_TRANS BIT(2)
#define BIT_BIST_RESET BIT(1)
#define BIT_BIST_EN BIT(0)
/* BIST DURATION0, default value: 0x00 */
#define REG_BIST_TEST_SEL 0x00bd
#define MSK_BIST_TEST_SEL_BIST_PATT_SEL 0x0f
/* BIST VIDEO_MODE, default value: 0x00 */
#define REG_BIST_VIDEO_MODE 0x00be
#define MSK_BIST_VIDEO_MODE_BIST_VIDEO_MODE_3_0 0x0f
/* BIST DURATION0, default value: 0x00 */
#define REG_BIST_DURATION_0 0x00bf
/* BIST DURATION1, default value: 0x00 */
#define REG_BIST_DURATION_1 0x00c0
/* BIST DURATION2, default value: 0x00 */
#define REG_BIST_DURATION_2 0x00c1
/* BIST 8BIT_PATTERN, default value: 0x00 */
#define REG_BIST_8BIT_PATTERN 0x00c2
/* LM DDC, default value: 0x80 */
#define REG_LM_DDC 0x00c7
#define BIT_LM_DDC_SW_TPI_EN_DISABLED BIT(7)
#define BIT_LM_DDC_VIDEO_MUTE_EN BIT(5)
#define BIT_LM_DDC_DDC_TPI_SW BIT(2)
#define BIT_LM_DDC_DDC_GRANT BIT(1)
#define BIT_LM_DDC_DDC_GPU_REQUEST BIT(0)
/* DDC I2C Manual, default value: 0x03 */
#define REG_DDC_MANUAL 0x00ec
#define BIT_DDC_MANUAL_MAN_DDC BIT(7)
#define BIT_DDC_MANUAL_VP_SEL BIT(6)
#define BIT_DDC_MANUAL_DSDA BIT(5)
#define BIT_DDC_MANUAL_DSCL BIT(4)
#define BIT_DDC_MANUAL_GCP_HW_CTL_EN BIT(3)
#define BIT_DDC_MANUAL_DDCM_ABORT_WP BIT(2)
#define BIT_DDC_MANUAL_IO_DSDA BIT(1)
#define BIT_DDC_MANUAL_IO_DSCL BIT(0)
/* DDC I2C Target Slave Address, default value: 0x00 */
#define REG_DDC_ADDR 0x00ed
#define MSK_DDC_ADDR_DDC_ADDR 0xfe
/* DDC I2C Target Segment Address, default value: 0x00 */
#define REG_DDC_SEGM 0x00ee
/* DDC I2C Target Offset Address, default value: 0x00 */
#define REG_DDC_OFFSET 0x00ef
/* DDC I2C Data In count #1, default value: 0x00 */
#define REG_DDC_DIN_CNT1 0x00f0
/* DDC I2C Data In count #2, default value: 0x00 */
#define REG_DDC_DIN_CNT2 0x00f1
#define MSK_DDC_DIN_CNT2_DDC_DIN_CNT_9_8 0x03
/* DDC I2C Status, default value: 0x04 */
#define REG_DDC_STATUS 0x00f2
#define BIT_DDC_STATUS_DDC_BUS_LOW BIT(6)
#define BIT_DDC_STATUS_DDC_NO_ACK BIT(5)
#define BIT_DDC_STATUS_DDC_I2C_IN_PROG BIT(4)
#define BIT_DDC_STATUS_DDC_FIFO_FULL BIT(3)
#define BIT_DDC_STATUS_DDC_FIFO_EMPTY BIT(2)
#define BIT_DDC_STATUS_DDC_FIFO_READ_IN_SUE BIT(1)
#define BIT_DDC_STATUS_DDC_FIFO_WRITE_IN_USE BIT(0)
/* DDC I2C Command, default value: 0x70 */
#define REG_DDC_CMD 0x00f3
#define BIT_DDC_CMD_HDCP_DDC_EN BIT(6)
#define BIT_DDC_CMD_SDA_DEL_EN BIT(5)
#define BIT_DDC_CMD_DDC_FLT_EN BIT(4)
#define MSK_DDC_CMD_DDC_CMD 0x0f
#define VAL_DDC_CMD_ENH_DDC_READ_NO_ACK 0x04
#define VAL_DDC_CMD_DDC_CMD_CLEAR_FIFO 0x09
#define VAL_DDC_CMD_DDC_CMD_ABORT 0x0f
/* DDC I2C FIFO Data In/Out, default value: 0x00 */
#define REG_DDC_DATA 0x00f4
/* DDC I2C Data Out Counter, default value: 0x00 */
#define REG_DDC_DOUT_CNT 0x00f5
#define BIT_DDC_DOUT_CNT_DDC_DELAY_CNT_8 BIT(7)
#define MSK_DDC_DOUT_CNT_DDC_DATA_OUT_CNT 0x1f
/* DDC I2C Delay Count, default value: 0x14 */
#define REG_DDC_DELAY_CNT 0x00f6
/* Test Control, default value: 0x80 */
#define REG_TEST_TXCTRL 0x00f7
#define BIT_TEST_TXCTRL_RCLK_REF_SEL BIT(7)
#define BIT_TEST_TXCTRL_PCLK_REF_SEL BIT(6)
#define MSK_TEST_TXCTRL_BYPASS_PLL_CLK 0x3c
#define BIT_TEST_TXCTRL_HDMI_MODE BIT(1)
#define BIT_TEST_TXCTRL_TST_PLLCK BIT(0)
/* CBUS Address, default value: 0x00 */
#define REG_PAGE_CBUS_ADDR 0x00f8
/* I2C Device Address re-assignment */
#define REG_PAGE1_ADDR 0x00fc
#define REG_PAGE2_ADDR 0x00fd
#define REG_PAGE3_ADDR 0x00fe
#define REG_HW_TPI_ADDR 0x00ff
/* USBT CTRL0, default value: 0x00 */
#define REG_UTSRST 0x0100
#define BIT_UTSRST_FC_SRST BIT(5)
#define BIT_UTSRST_KEEPER_SRST BIT(4)
#define BIT_UTSRST_HTX_SRST BIT(3)
#define BIT_UTSRST_TRX_SRST BIT(2)
#define BIT_UTSRST_TTX_SRST BIT(1)
#define BIT_UTSRST_HRX_SRST BIT(0)
/* HSIC RX Control3, default value: 0x07 */
#define REG_HRXCTRL3 0x0104
#define MSK_HRXCTRL3_HRX_AFFCTRL 0xf0
#define BIT_HRXCTRL3_HRX_OUT_EN BIT(2)
#define BIT_HRXCTRL3_STATUS_EN BIT(1)
#define BIT_HRXCTRL3_HRX_STAY_RESET BIT(0)
/* HSIC RX INT Registers */
#define REG_HRXINTL 0x0111
#define REG_HRXINTH 0x0112
/* TDM TX NUMBITS, default value: 0x0c */
#define REG_TTXNUMB 0x0116
#define MSK_TTXNUMB_TTX_AFFCTRL_3_0 0xf0
#define BIT_TTXNUMB_TTX_COM1_AT_SYNC_WAIT BIT(3)
#define MSK_TTXNUMB_TTX_NUMBPS 0x07
/* TDM TX NUMSPISYM, default value: 0x04 */
#define REG_TTXSPINUMS 0x0117
/* TDM TX NUMHSICSYM, default value: 0x14 */
#define REG_TTXHSICNUMS 0x0118
/* TDM TX NUMTOTSYM, default value: 0x18 */
#define REG_TTXTOTNUMS 0x0119
/* TDM TX INT Low, default value: 0x00 */
#define REG_TTXINTL 0x0136
#define BIT_TTXINTL_TTX_INTR7 BIT(7)
#define BIT_TTXINTL_TTX_INTR6 BIT(6)
#define BIT_TTXINTL_TTX_INTR5 BIT(5)
#define BIT_TTXINTL_TTX_INTR4 BIT(4)
#define BIT_TTXINTL_TTX_INTR3 BIT(3)
#define BIT_TTXINTL_TTX_INTR2 BIT(2)
#define BIT_TTXINTL_TTX_INTR1 BIT(1)
#define BIT_TTXINTL_TTX_INTR0 BIT(0)
/* TDM TX INT High, default value: 0x00 */
#define REG_TTXINTH 0x0137
#define BIT_TTXINTH_TTX_INTR15 BIT(7)
#define BIT_TTXINTH_TTX_INTR14 BIT(6)
#define BIT_TTXINTH_TTX_INTR13 BIT(5)
#define BIT_TTXINTH_TTX_INTR12 BIT(4)
#define BIT_TTXINTH_TTX_INTR11 BIT(3)
#define BIT_TTXINTH_TTX_INTR10 BIT(2)
#define BIT_TTXINTH_TTX_INTR9 BIT(1)
#define BIT_TTXINTH_TTX_INTR8 BIT(0)
/* TDM RX Control, default value: 0x1c */
#define REG_TRXCTRL 0x013b
#define BIT_TRXCTRL_TRX_CLR_WVALLOW BIT(4)
#define BIT_TRXCTRL_TRX_FROM_SE_COC BIT(3)
#define MSK_TRXCTRL_TRX_NUMBPS_2_0 0x07
/* TDM RX NUMSPISYM, default value: 0x04 */
#define REG_TRXSPINUMS 0x013c
/* TDM RX NUMHSICSYM, default value: 0x14 */
#define REG_TRXHSICNUMS 0x013d
/* TDM RX NUMTOTSYM, default value: 0x18 */
#define REG_TRXTOTNUMS 0x013e
/* TDM RX Status 2nd, default value: 0x00 */
#define REG_TRXSTA2 0x015c
#define MSK_TDM_SYNCHRONIZED 0xc0
#define VAL_TDM_SYNCHRONIZED 0x80
/* TDM RX INT Low, default value: 0x00 */
#define REG_TRXINTL 0x0163
/* TDM RX INT High, default value: 0x00 */
#define REG_TRXINTH 0x0164
#define BIT_TDM_INTR_SYNC_DATA BIT(0)
#define BIT_TDM_INTR_SYNC_WAIT BIT(1)
/* TDM RX INTMASK High, default value: 0x00 */
#define REG_TRXINTMH 0x0166
/* HSIC TX CRTL, default value: 0x00 */
#define REG_HTXCTRL 0x0169
#define BIT_HTXCTRL_HTX_ALLSBE_SOP BIT(4)
#define BIT_HTXCTRL_HTX_RGDINV_USB BIT(3)
#define BIT_HTXCTRL_HTX_RSPTDM_BUSY BIT(2)
#define BIT_HTXCTRL_HTX_DRVCONN1 BIT(1)
#define BIT_HTXCTRL_HTX_DRVRST1 BIT(0)
/* HSIC TX INT Low, default value: 0x00 */
#define REG_HTXINTL 0x017d
/* HSIC TX INT High, default value: 0x00 */
#define REG_HTXINTH 0x017e
/* HSIC Keeper, default value: 0x00 */
#define REG_KEEPER 0x0181
#define MSK_KEEPER_MODE 0x03
#define VAL_KEEPER_MODE_HOST 0
#define VAL_KEEPER_MODE_DEVICE 2
/* HSIC Flow Control General, default value: 0x02 */
#define REG_FCGC 0x0183
#define BIT_FCGC_HSIC_HOSTMODE BIT(1)
#define BIT_FCGC_HSIC_ENABLE BIT(0)
/* HSIC Flow Control CTR13, default value: 0xfc */
#define REG_FCCTR13 0x0191
/* HSIC Flow Control CTR14, default value: 0xff */
#define REG_FCCTR14 0x0192
/* HSIC Flow Control CTR15, default value: 0xff */
#define REG_FCCTR15 0x0193
/* HSIC Flow Control CTR50, default value: 0x03 */
#define REG_FCCTR50 0x01b6
/* HSIC Flow Control INTR0, default value: 0x00 */
#define REG_FCINTR0 0x01ec
#define REG_FCINTR1 0x01ed
#define REG_FCINTR2 0x01ee
#define REG_FCINTR3 0x01ef
#define REG_FCINTR4 0x01f0
#define REG_FCINTR5 0x01f1
#define REG_FCINTR6 0x01f2
#define REG_FCINTR7 0x01f3
/* TDM Low Latency, default value: 0x20 */
#define REG_TDMLLCTL 0x01fc
#define MSK_TDMLLCTL_TRX_LL_SEL_MANUAL 0xc0
#define MSK_TDMLLCTL_TRX_LL_SEL_MODE 0x30
#define MSK_TDMLLCTL_TTX_LL_SEL_MANUAL 0x0c
#define BIT_TDMLLCTL_TTX_LL_TIE_LOW BIT(1)
#define BIT_TDMLLCTL_TTX_LL_SEL_MODE BIT(0)
/* TMDS 0 Clock Control, default value: 0x10 */
#define REG_TMDS0_CCTRL1 0x0210
#define MSK_TMDS0_CCTRL1_TEST_SEL 0xc0
#define MSK_TMDS0_CCTRL1_CLK1X_CTL 0x30
/* TMDS Clock Enable, default value: 0x00 */
#define REG_TMDS_CLK_EN 0x0211
#define BIT_TMDS_CLK_EN_CLK_EN BIT(0)
/* TMDS Channel Enable, default value: 0x00 */
#define REG_TMDS_CH_EN 0x0212
#define BIT_TMDS_CH_EN_CH0_EN BIT(4)
#define BIT_TMDS_CH_EN_CH12_EN BIT(0)
/* BGR_BIAS, default value: 0x07 */
#define REG_BGR_BIAS 0x0215
#define BIT_BGR_BIAS_BGR_EN BIT(7)
#define MSK_BGR_BIAS_BIAS_BGR_D 0x0f
/* TMDS 0 Digital I2C BW, default value: 0x0a */
#define REG_ALICE0_BW_I2C 0x0231
/* TMDS 0 Digital Zone Control, default value: 0xe0 */
#define REG_ALICE0_ZONE_CTRL 0x024c
#define BIT_ALICE0_ZONE_CTRL_ICRST_N BIT(7)
#define BIT_ALICE0_ZONE_CTRL_USE_INT_DIV20 BIT(6)
#define MSK_ALICE0_ZONE_CTRL_SZONE_I2C 0x30
#define MSK_ALICE0_ZONE_CTRL_ZONE_CTRL 0x0f
/* TMDS 0 Digital PLL Mode Control, default value: 0x00 */
#define REG_ALICE0_MODE_CTRL 0x024d
#define MSK_ALICE0_MODE_CTRL_PLL_MODE_I2C 0x0c
#define MSK_ALICE0_MODE_CTRL_DIV20_CTRL 0x03
/* MHL Tx Control 6th, default value: 0xa0 */
#define REG_MHLTX_CTL6 0x0285
#define MSK_MHLTX_CTL6_EMI_SEL 0xe0
#define MSK_MHLTX_CTL6_TX_CLK_SHAPE_9_8 0x03
/* Packet Filter0, default value: 0x00 */
#define REG_PKT_FILTER_0 0x0290
#define BIT_PKT_FILTER_0_DROP_CEA_GAMUT_PKT BIT(7)
#define BIT_PKT_FILTER_0_DROP_CEA_CP_PKT BIT(6)
#define BIT_PKT_FILTER_0_DROP_MPEG_PKT BIT(5)
#define BIT_PKT_FILTER_0_DROP_SPIF_PKT BIT(4)
#define BIT_PKT_FILTER_0_DROP_AIF_PKT BIT(3)
#define BIT_PKT_FILTER_0_DROP_AVI_PKT BIT(2)
#define BIT_PKT_FILTER_0_DROP_CTS_PKT BIT(1)
#define BIT_PKT_FILTER_0_DROP_GCP_PKT BIT(0)
/* Packet Filter1, default value: 0x00 */
#define REG_PKT_FILTER_1 0x0291
#define BIT_PKT_FILTER_1_VSI_OVERRIDE_DIS BIT(7)
#define BIT_PKT_FILTER_1_AVI_OVERRIDE_DIS BIT(6)
#define BIT_PKT_FILTER_1_DROP_AUDIO_PKT BIT(3)
#define BIT_PKT_FILTER_1_DROP_GEN2_PKT BIT(2)
#define BIT_PKT_FILTER_1_DROP_GEN_PKT BIT(1)
#define BIT_PKT_FILTER_1_DROP_VSIF_PKT BIT(0)
/* TMDS Clock Status, default value: 0x10 */
#define REG_TMDS_CSTAT_P3 0x02a0
#define BIT_TMDS_CSTAT_P3_RX_HDMI_CP_CLR_MUTE BIT(7)
#define BIT_TMDS_CSTAT_P3_RX_HDMI_CP_SET_MUTE BIT(6)
#define BIT_TMDS_CSTAT_P3_RX_HDMI_CP_NEW_CP BIT(5)
#define BIT_TMDS_CSTAT_P3_CLR_AVI BIT(3)
#define BIT_TMDS_CSTAT_P3_SCDT_CLR_AVI_DIS BIT(2)
#define BIT_TMDS_CSTAT_P3_SCDT BIT(1)
#define BIT_TMDS_CSTAT_P3_CKDT BIT(0)
/* RX_HDMI Control, default value: 0x10 */
#define REG_RX_HDMI_CTRL0 0x02a1
#define BIT_RX_HDMI_CTRL0_BYP_DVIFILT_SYNC BIT(5)
#define BIT_RX_HDMI_CTRL0_HDMI_MODE_EN_ITSELF_CLR BIT(4)
#define BIT_RX_HDMI_CTRL0_HDMI_MODE_SW_VALUE BIT(3)
#define BIT_RX_HDMI_CTRL0_HDMI_MODE_OVERWRITE BIT(2)
#define BIT_RX_HDMI_CTRL0_RX_HDMI_HDMI_MODE_EN BIT(1)
#define BIT_RX_HDMI_CTRL0_RX_HDMI_HDMI_MODE BIT(0)
/* RX_HDMI Control, default value: 0x38 */
#define REG_RX_HDMI_CTRL2 0x02a3
#define MSK_RX_HDMI_CTRL2_IDLE_CNT 0xf0
#define VAL_RX_HDMI_CTRL2_IDLE_CNT(n) ((n) << 4)
#define BIT_RX_HDMI_CTRL2_USE_AV_MUTE BIT(3)
#define BIT_RX_HDMI_CTRL2_VSI_MON_SEL_VSI BIT(0)
/* RX_HDMI Control, default value: 0x0f */
#define REG_RX_HDMI_CTRL3 0x02a4
#define MSK_RX_HDMI_CTRL3_PP_MODE_CLK_EN 0x0f
/* rx_hdmi Clear Buffer, default value: 0x00 */
#define REG_RX_HDMI_CLR_BUFFER 0x02ac
#define MSK_RX_HDMI_CLR_BUFFER_AIF4VSI_CMP 0xc0
#define BIT_RX_HDMI_CLR_BUFFER_USE_AIF4VSI BIT(5)
#define BIT_RX_HDMI_CLR_BUFFER_VSI_CLR_W_AVI BIT(4)
#define BIT_RX_HDMI_CLR_BUFFER_VSI_IEEE_ID_CHK_EN BIT(3)
#define BIT_RX_HDMI_CLR_BUFFER_SWAP_VSI_IEEE_ID BIT(2)
#define BIT_RX_HDMI_CLR_BUFFER_AIF_CLR_EN BIT(1)
#define BIT_RX_HDMI_CLR_BUFFER_VSI_CLR_EN BIT(0)
/* RX_HDMI VSI Header1, default value: 0x00 */
#define REG_RX_HDMI_MON_PKT_HEADER1 0x02b8
/* RX_HDMI VSI MHL Monitor, default value: 0x3c */
#define REG_RX_HDMI_VSIF_MHL_MON 0x02d7
#define MSK_RX_HDMI_VSIF_MHL_MON_RX_HDMI_MHL_3D_FORMAT 0x3c
#define MSK_RX_HDMI_VSIF_MHL_MON_RX_HDMI_MHL_VID_FORMAT 0x03
/* Interrupt Source 9, default value: 0x00 */
#define REG_INTR9 0x02e0
#define BIT_INTR9_EDID_ERROR BIT(6)
#define BIT_INTR9_EDID_DONE BIT(5)
#define BIT_INTR9_DEVCAP_DONE BIT(4)
/* Interrupt 9 Mask, default value: 0x00 */
#define REG_INTR9_MASK 0x02e1
/* TPI CBUS Start, default value: 0x00 */
#define REG_TPI_CBUS_START 0x02e2
#define BIT_TPI_CBUS_START_RCP_REQ_START BIT(7)
#define BIT_TPI_CBUS_START_RCPK_REPLY_START BIT(6)
#define BIT_TPI_CBUS_START_RCPE_REPLY_START BIT(5)
#define BIT_TPI_CBUS_START_PUT_LINK_MODE_START BIT(4)
#define BIT_TPI_CBUS_START_PUT_DCAPCHG_START BIT(3)
#define BIT_TPI_CBUS_START_PUT_DCAPRDY_START BIT(2)
#define BIT_TPI_CBUS_START_GET_EDID_START_0 BIT(1)
#define BIT_TPI_CBUS_START_GET_DEVCAP_START BIT(0)
/* EDID Control, default value: 0x10 */
#define REG_EDID_CTRL 0x02e3
#define BIT_EDID_CTRL_EDID_PRIME_VALID BIT(7)
#define BIT_EDID_CTRL_XDEVCAP_EN BIT(6)
#define BIT_EDID_CTRL_DEVCAP_SELECT_DEVCAP BIT(5)
#define BIT_EDID_CTRL_EDID_FIFO_ADDR_AUTO BIT(4)
#define BIT_EDID_CTRL_EDID_FIFO_ACCESS_ALWAYS_EN BIT(3)
#define BIT_EDID_CTRL_EDID_FIFO_BLOCK_SEL BIT(2)
#define BIT_EDID_CTRL_INVALID_BKSV BIT(1)
#define BIT_EDID_CTRL_EDID_MODE_EN BIT(0)
/* EDID FIFO Addr, default value: 0x00 */
#define REG_EDID_FIFO_ADDR 0x02e9
/* EDID FIFO Write Data, default value: 0x00 */
#define REG_EDID_FIFO_WR_DATA 0x02ea
/* EDID/DEVCAP FIFO Internal Addr, default value: 0x00 */
#define REG_EDID_FIFO_ADDR_MON 0x02eb
/* EDID FIFO Read Data, default value: 0x00 */
#define REG_EDID_FIFO_RD_DATA 0x02ec
/* EDID DDC Segment Pointer, default value: 0x00 */
#define REG_EDID_START_EXT 0x02ed
/* TX IP BIST CNTL and Status, default value: 0x00 */
#define REG_TX_IP_BIST_CNTLSTA 0x02f2
#define BIT_TX_IP_BIST_CNTLSTA_TXBIST_QUARTER_CLK_SEL BIT(6)
#define BIT_TX_IP_BIST_CNTLSTA_TXBIST_DONE BIT(5)
#define BIT_TX_IP_BIST_CNTLSTA_TXBIST_ON BIT(4)
#define BIT_TX_IP_BIST_CNTLSTA_TXBIST_RUN BIT(3)
#define BIT_TX_IP_BIST_CNTLSTA_TXCLK_HALF_SEL BIT(2)
#define BIT_TX_IP_BIST_CNTLSTA_TXBIST_EN BIT(1)
#define BIT_TX_IP_BIST_CNTLSTA_TXBIST_SEL BIT(0)
/* TX IP BIST INST LOW, default value: 0x00 */
#define REG_TX_IP_BIST_INST_LOW 0x02f3
#define REG_TX_IP_BIST_INST_HIGH 0x02f4
/* TX IP BIST PATTERN LOW, default value: 0x00 */
#define REG_TX_IP_BIST_PAT_LOW 0x02f5
#define REG_TX_IP_BIST_PAT_HIGH 0x02f6
/* TX IP BIST CONFIGURE LOW, default value: 0x00 */
#define REG_TX_IP_BIST_CONF_LOW 0x02f7
#define REG_TX_IP_BIST_CONF_HIGH 0x02f8
/* E-MSC General Control, default value: 0x80 */
#define REG_GENCTL 0x0300
#define BIT_GENCTL_SPEC_TRANS_DIS BIT(7)
#define BIT_GENCTL_DIS_XMIT_ERR_STATE BIT(6)
#define BIT_GENCTL_SPI_MISO_EDGE BIT(5)
#define BIT_GENCTL_SPI_MOSI_EDGE BIT(4)
#define BIT_GENCTL_CLR_EMSC_RFIFO BIT(3)
#define BIT_GENCTL_CLR_EMSC_XFIFO BIT(2)
#define BIT_GENCTL_START_TRAIN_SEQ BIT(1)
#define BIT_GENCTL_EMSC_EN BIT(0)
/* E-MSC Comma ErrorCNT, default value: 0x03 */
#define REG_COMMECNT 0x0305
#define BIT_COMMECNT_I2C_TO_EMSC_EN BIT(7)
#define MSK_COMMECNT_COMMA_CHAR_ERR_CNT 0x0f
/* E-MSC RFIFO ByteCnt, default value: 0x00 */
#define REG_EMSCRFIFOBCNTL 0x031a
#define REG_EMSCRFIFOBCNTH 0x031b
/* SPI Burst Cnt Status, default value: 0x00 */
#define REG_SPIBURSTCNT 0x031e
/* SPI Burst Status and SWRST, default value: 0x00 */
#define REG_SPIBURSTSTAT 0x0322
#define BIT_SPIBURSTSTAT_SPI_HDCPRST BIT(7)
#define BIT_SPIBURSTSTAT_SPI_CBUSRST BIT(6)
#define BIT_SPIBURSTSTAT_SPI_SRST BIT(5)
#define BIT_SPIBURSTSTAT_EMSC_NORMAL_MODE BIT(0)
/* E-MSC 1st Interrupt, default value: 0x00 */
#define REG_EMSCINTR 0x0323
#define BIT_EMSCINTR_EMSC_XFIFO_EMPTY BIT(7)
#define BIT_EMSCINTR_EMSC_XMIT_ACK_TOUT BIT(6)
#define BIT_EMSCINTR_EMSC_RFIFO_READ_ERR BIT(5)
#define BIT_EMSCINTR_EMSC_XFIFO_WRITE_ERR BIT(4)
#define BIT_EMSCINTR_EMSC_COMMA_CHAR_ERR BIT(3)
#define BIT_EMSCINTR_EMSC_XMIT_DONE BIT(2)
#define BIT_EMSCINTR_EMSC_XMIT_GNT_TOUT BIT(1)
#define BIT_EMSCINTR_SPI_DVLD BIT(0)
/* E-MSC Interrupt Mask, default value: 0x00 */
#define REG_EMSCINTRMASK 0x0324
/* I2C E-MSC XMIT FIFO Write Port, default value: 0x00 */
#define REG_EMSC_XMIT_WRITE_PORT 0x032a
/* I2C E-MSC RCV FIFO Write Port, default value: 0x00 */
#define REG_EMSC_RCV_READ_PORT 0x032b
/* E-MSC 2nd Interrupt, default value: 0x00 */
#define REG_EMSCINTR1 0x032c
#define BIT_EMSCINTR1_EMSC_TRAINING_COMMA_ERR BIT(0)
/* E-MSC Interrupt Mask, default value: 0x00 */
#define REG_EMSCINTRMASK1 0x032d
#define BIT_EMSCINTRMASK1_EMSC_INTRMASK1_0 BIT(0)
/* MHL Top Ctl, default value: 0x00 */
#define REG_MHL_TOP_CTL 0x0330
#define BIT_MHL_TOP_CTL_MHL3_DOC_SEL BIT(7)
#define BIT_MHL_TOP_CTL_MHL_PP_SEL BIT(6)
#define MSK_MHL_TOP_CTL_IF_TIMING_CTL 0x03
/* MHL DataPath 1st Ctl, default value: 0xbc */
#define REG_MHL_DP_CTL0 0x0331
#define BIT_MHL_DP_CTL0_DP_OE BIT(7)
#define BIT_MHL_DP_CTL0_TX_OE_OVR BIT(6)
#define MSK_MHL_DP_CTL0_TX_OE 0x3f
/* MHL DataPath 2nd Ctl, default value: 0xbb */
#define REG_MHL_DP_CTL1 0x0332
#define MSK_MHL_DP_CTL1_CK_SWING_CTL 0xf0
#define MSK_MHL_DP_CTL1_DT_SWING_CTL 0x0f
/* MHL DataPath 3rd Ctl, default value: 0x2f */
#define REG_MHL_DP_CTL2 0x0333
#define BIT_MHL_DP_CTL2_CLK_BYPASS_EN BIT(7)
#define MSK_MHL_DP_CTL2_DAMP_TERM_SEL 0x30
#define MSK_MHL_DP_CTL2_CK_TERM_SEL 0x0c
#define MSK_MHL_DP_CTL2_DT_TERM_SEL 0x03
/* MHL DataPath 4th Ctl, default value: 0x48 */
#define REG_MHL_DP_CTL3 0x0334
#define MSK_MHL_DP_CTL3_DT_DRV_VNBC_CTL 0xf0
#define MSK_MHL_DP_CTL3_DT_DRV_VNB_CTL 0x0f
/* MHL DataPath 5th Ctl, default value: 0x48 */
#define REG_MHL_DP_CTL4 0x0335
#define MSK_MHL_DP_CTL4_CK_DRV_VNBC_CTL 0xf0
#define MSK_MHL_DP_CTL4_CK_DRV_VNB_CTL 0x0f
/* MHL DataPath 6th Ctl, default value: 0x3f */
#define REG_MHL_DP_CTL5 0x0336
#define BIT_MHL_DP_CTL5_RSEN_EN_OVR BIT(7)
#define BIT_MHL_DP_CTL5_RSEN_EN BIT(6)
#define MSK_MHL_DP_CTL5_DAMP_TERM_VGS_CTL 0x30
#define MSK_MHL_DP_CTL5_CK_TERM_VGS_CTL 0x0c
#define MSK_MHL_DP_CTL5_DT_TERM_VGS_CTL 0x03
/* MHL PLL 1st Ctl, default value: 0x05 */
#define REG_MHL_PLL_CTL0 0x0337
#define BIT_MHL_PLL_CTL0_AUD_CLK_EN BIT(7)
#define MSK_MHL_PLL_CTL0_AUD_CLK_RATIO 0x70
#define VAL_MHL_PLL_CTL0_AUD_CLK_RATIO_5_10 0x70
#define VAL_MHL_PLL_CTL0_AUD_CLK_RATIO_5_6 0x60
#define VAL_MHL_PLL_CTL0_AUD_CLK_RATIO_5_4 0x50
#define VAL_MHL_PLL_CTL0_AUD_CLK_RATIO_5_2 0x40
#define VAL_MHL_PLL_CTL0_AUD_CLK_RATIO_5_5 0x30
#define VAL_MHL_PLL_CTL0_AUD_CLK_RATIO_5_3 0x20
#define VAL_MHL_PLL_CTL0_AUD_CLK_RATIO_5_2_PRIME 0x10
#define VAL_MHL_PLL_CTL0_AUD_CLK_RATIO_5_1 0x00
#define MSK_MHL_PLL_CTL0_HDMI_CLK_RATIO 0x0c
#define VAL_MHL_PLL_CTL0_HDMI_CLK_RATIO_4X 0x0c
#define VAL_MHL_PLL_CTL0_HDMI_CLK_RATIO_2X 0x08
#define VAL_MHL_PLL_CTL0_HDMI_CLK_RATIO_1X 0x04
#define VAL_MHL_PLL_CTL0_HDMI_CLK_RATIO_HALF_X 0x00
#define BIT_MHL_PLL_CTL0_CRYSTAL_CLK_SEL BIT(1)
#define BIT_MHL_PLL_CTL0_ZONE_MASK_OE BIT(0)
/* MHL PLL 3rd Ctl, default value: 0x80 */
#define REG_MHL_PLL_CTL2 0x0339
#define BIT_MHL_PLL_CTL2_CLKDETECT_EN BIT(7)
#define BIT_MHL_PLL_CTL2_MEAS_FVCO BIT(3)
#define BIT_MHL_PLL_CTL2_PLL_FAST_LOCK BIT(2)
#define MSK_MHL_PLL_CTL2_PLL_LF_SEL 0x03
/* MHL CBUS 1st Ctl, default value: 0x12 */
#define REG_MHL_CBUS_CTL0 0x0340
#define BIT_MHL_CBUS_CTL0_CBUS_RGND_TEST_MODE BIT(7)
#define MSK_MHL_CBUS_CTL0_CBUS_RGND_VTH_CTL 0x30
#define VAL_MHL_CBUS_CTL0_CBUS_RGND_VBIAS_734 0x00
#define VAL_MHL_CBUS_CTL0_CBUS_RGND_VBIAS_747 0x10
#define VAL_MHL_CBUS_CTL0_CBUS_RGND_VBIAS_740 0x20
#define VAL_MHL_CBUS_CTL0_CBUS_RGND_VBIAS_754 0x30
#define MSK_MHL_CBUS_CTL0_CBUS_RES_TEST_SEL 0x0c
#define MSK_MHL_CBUS_CTL0_CBUS_DRV_SEL 0x03
#define VAL_MHL_CBUS_CTL0_CBUS_DRV_SEL_WEAKEST 0x00
#define VAL_MHL_CBUS_CTL0_CBUS_DRV_SEL_WEAK 0x01
#define VAL_MHL_CBUS_CTL0_CBUS_DRV_SEL_STRONG 0x02
#define VAL_MHL_CBUS_CTL0_CBUS_DRV_SEL_STRONGEST 0x03
/* MHL CBUS 2nd Ctl, default value: 0x03 */
#define REG_MHL_CBUS_CTL1 0x0341
#define MSK_MHL_CBUS_CTL1_CBUS_RGND_RES_CTL 0x07
#define VAL_MHL_CBUS_CTL1_0888_OHM 0x00
#define VAL_MHL_CBUS_CTL1_1115_OHM 0x04
#define VAL_MHL_CBUS_CTL1_1378_OHM 0x07
/* MHL CoC 1st Ctl, default value: 0xc3 */
#define REG_MHL_COC_CTL0 0x0342
#define BIT_MHL_COC_CTL0_COC_BIAS_EN BIT(7)
#define MSK_MHL_COC_CTL0_COC_BIAS_CTL 0x70
#define MSK_MHL_COC_CTL0_COC_TERM_CTL 0x07
/* MHL CoC 2nd Ctl, default value: 0x87 */
#define REG_MHL_COC_CTL1 0x0343
#define BIT_MHL_COC_CTL1_COC_EN BIT(7)
#define MSK_MHL_COC_CTL1_COC_DRV_CTL 0x3f
/* MHL CoC 4th Ctl, default value: 0x00 */
#define REG_MHL_COC_CTL3 0x0345
#define BIT_MHL_COC_CTL3_COC_AECHO_EN BIT(0)
/* MHL CoC 5th Ctl, default value: 0x28 */
#define REG_MHL_COC_CTL4 0x0346
#define MSK_MHL_COC_CTL4_COC_IF_CTL 0xf0
#define MSK_MHL_COC_CTL4_COC_SLEW_CTL 0x0f
/* MHL CoC 6th Ctl, default value: 0x0d */
#define REG_MHL_COC_CTL5 0x0347
/* MHL DoC 1st Ctl, default value: 0x18 */
#define REG_MHL_DOC_CTL0 0x0349
#define BIT_MHL_DOC_CTL0_DOC_RXDATA_EN BIT(7)
#define MSK_MHL_DOC_CTL0_DOC_DM_TERM 0x38
#define MSK_MHL_DOC_CTL0_DOC_OPMODE 0x06
#define BIT_MHL_DOC_CTL0_DOC_RXBIAS_EN BIT(0)
/* MHL DataPath 7th Ctl, default value: 0x2a */
#define REG_MHL_DP_CTL6 0x0350
#define BIT_MHL_DP_CTL6_DP_TAP2_SGN BIT(5)
#define BIT_MHL_DP_CTL6_DP_TAP2_EN BIT(4)
#define BIT_MHL_DP_CTL6_DP_TAP1_SGN BIT(3)
#define BIT_MHL_DP_CTL6_DP_TAP1_EN BIT(2)
#define BIT_MHL_DP_CTL6_DT_PREDRV_FEEDCAP_EN BIT(1)
#define BIT_MHL_DP_CTL6_DP_PRE_POST_SEL BIT(0)
/* MHL DataPath 8th Ctl, default value: 0x06 */
#define REG_MHL_DP_CTL7 0x0351
#define MSK_MHL_DP_CTL7_DT_DRV_VBIAS_CASCTL 0xf0
#define MSK_MHL_DP_CTL7_DT_DRV_IREF_CTL 0x0f
#define REG_MHL_DP_CTL8 0x0352
/* Tx Zone Ctl1, default value: 0x00 */
#define REG_TX_ZONE_CTL1 0x0361
#define VAL_TX_ZONE_CTL1_TX_ZONE_CTRL_MODE 0x08
/* MHL3 Tx Zone Ctl, default value: 0x00 */
#define REG_MHL3_TX_ZONE_CTL 0x0364
#define BIT_MHL3_TX_ZONE_CTL_MHL2_INTPLT_ZONE_MANU_EN BIT(7)
#define MSK_MHL3_TX_ZONE_CTL_MHL3_TX_ZONE 0x03
#define MSK_TX_ZONE_CTL3_TX_ZONE 0x03
#define VAL_TX_ZONE_CTL3_TX_ZONE_6GBPS 0x00
#define VAL_TX_ZONE_CTL3_TX_ZONE_3GBPS 0x01
#define VAL_TX_ZONE_CTL3_TX_ZONE_1_5GBPS 0x02
/* HDCP Polling Control and Status, default value: 0x70 */
#define REG_HDCP2X_POLL_CS 0x0391
#define BIT_HDCP2X_POLL_CS_HDCP2X_MSG_SZ_CLR_OPTION BIT(6)
#define BIT_HDCP2X_POLL_CS_HDCP2X_RPT_READY_CLR_OPTION BIT(5)
#define BIT_HDCP2X_POLL_CS_HDCP2X_REAUTH_REQ_CLR_OPTION BIT(4)
#define MSK_HDCP2X_POLL_CS_ 0x0c
#define BIT_HDCP2X_POLL_CS_HDCP2X_DIS_POLL_GNT BIT(1)
#define BIT_HDCP2X_POLL_CS_HDCP2X_DIS_POLL_EN BIT(0)
/* HDCP Interrupt 0, default value: 0x00 */
#define REG_HDCP2X_INTR0 0x0398
/* HDCP Interrupt 0 Mask, default value: 0x00 */
#define REG_HDCP2X_INTR0_MASK 0x0399
/* HDCP General Control 0, default value: 0x02 */
#define REG_HDCP2X_CTRL_0 0x03a0
#define BIT_HDCP2X_CTRL_0_HDCP2X_ENCRYPT_EN BIT(7)
#define BIT_HDCP2X_CTRL_0_HDCP2X_POLINT_SEL BIT(6)
#define BIT_HDCP2X_CTRL_0_HDCP2X_POLINT_OVR BIT(5)
#define BIT_HDCP2X_CTRL_0_HDCP2X_PRECOMPUTE BIT(4)
#define BIT_HDCP2X_CTRL_0_HDCP2X_HDMIMODE BIT(3)
#define BIT_HDCP2X_CTRL_0_HDCP2X_REPEATER BIT(2)
#define BIT_HDCP2X_CTRL_0_HDCP2X_HDCPTX BIT(1)
#define BIT_HDCP2X_CTRL_0_HDCP2X_EN BIT(0)
/* HDCP General Control 1, default value: 0x08 */
#define REG_HDCP2X_CTRL_1 0x03a1
#define MSK_HDCP2X_CTRL_1_HDCP2X_REAUTH_MSK_3_0 0xf0
#define BIT_HDCP2X_CTRL_1_HDCP2X_HPD_SW BIT(3)
#define BIT_HDCP2X_CTRL_1_HDCP2X_HPD_OVR BIT(2)
#define BIT_HDCP2X_CTRL_1_HDCP2X_CTL3MSK BIT(1)
#define BIT_HDCP2X_CTRL_1_HDCP2X_REAUTH_SW BIT(0)
/* HDCP Misc Control, default value: 0x00 */
#define REG_HDCP2X_MISC_CTRL 0x03a5
#define BIT_HDCP2X_MISC_CTRL_HDCP2X_RPT_SMNG_XFER_START BIT(4)
#define BIT_HDCP2X_MISC_CTRL_HDCP2X_RPT_SMNG_WR_START BIT(3)
#define BIT_HDCP2X_MISC_CTRL_HDCP2X_RPT_SMNG_WR BIT(2)
#define BIT_HDCP2X_MISC_CTRL_HDCP2X_RPT_RCVID_RD_START BIT(1)
#define BIT_HDCP2X_MISC_CTRL_HDCP2X_RPT_RCVID_RD BIT(0)
/* HDCP RPT SMNG K, default value: 0x00 */
#define REG_HDCP2X_RPT_SMNG_K 0x03a6
/* HDCP RPT SMNG In, default value: 0x00 */
#define REG_HDCP2X_RPT_SMNG_IN 0x03a7
/* HDCP Auth Status, default value: 0x00 */
#define REG_HDCP2X_AUTH_STAT 0x03aa
/* HDCP RPT RCVID Out, default value: 0x00 */
#define REG_HDCP2X_RPT_RCVID_OUT 0x03ac
/* HDCP TP1, default value: 0x62 */
#define REG_HDCP2X_TP1 0x03b4
/* HDCP GP Out 0, default value: 0x00 */
#define REG_HDCP2X_GP_OUT0 0x03c7
/* HDCP Repeater RCVR ID 0, default value: 0x00 */
#define REG_HDCP2X_RPT_RCVR_ID0 0x03d1
/* HDCP DDCM Status, default value: 0x00 */
#define REG_HDCP2X_DDCM_STS 0x03d8
#define MSK_HDCP2X_DDCM_STS_HDCP2X_DDCM_ERR_STS_3_0 0xf0
#define MSK_HDCP2X_DDCM_STS_HDCP2X_DDCM_CTL_CS_3_0 0x0f
/* HDMI2MHL3 Control, default value: 0x0a */
#define REG_M3_CTRL 0x03e0
#define BIT_M3_CTRL_H2M_SWRST BIT(4)
#define BIT_M3_CTRL_SW_MHL3_SEL BIT(3)
#define BIT_M3_CTRL_M3AV_EN BIT(2)
#define BIT_M3_CTRL_ENC_TMDS BIT(1)
#define BIT_M3_CTRL_MHL3_MASTER_EN BIT(0)
#define VAL_M3_CTRL_MHL1_2_VALUE (BIT_M3_CTRL_SW_MHL3_SEL \
| BIT_M3_CTRL_ENC_TMDS)
#define VAL_M3_CTRL_MHL3_VALUE (BIT_M3_CTRL_SW_MHL3_SEL \
| BIT_M3_CTRL_M3AV_EN \
| BIT_M3_CTRL_ENC_TMDS \
| BIT_M3_CTRL_MHL3_MASTER_EN)
/* HDMI2MHL3 Port0 Control, default value: 0x04 */
#define REG_M3_P0CTRL 0x03e1
#define BIT_M3_P0CTRL_MHL3_P0_HDCP_ENC_EN BIT(4)
#define BIT_M3_P0CTRL_MHL3_P0_UNLIMIT_EN BIT(3)
#define BIT_M3_P0CTRL_MHL3_P0_HDCP_EN BIT(2)
#define BIT_M3_P0CTRL_MHL3_P0_PIXEL_MODE_PACKED BIT(1)
#define BIT_M3_P0CTRL_MHL3_P0_PORT_EN BIT(0)
#define REG_M3_POSTM 0x03e2
#define MSK_M3_POSTM_RRP_DECODE 0xf8
#define MSK_M3_POSTM_MHL3_P0_STM_ID 0x07
/* HDMI2MHL3 Scramble Control, default value: 0x41 */
#define REG_M3_SCTRL 0x03e6
#define MSK_M3_SCTRL_MHL3_SR_LENGTH 0xf0
#define BIT_M3_SCTRL_MHL3_SCRAMBLER_EN BIT(0)
/* HSIC Div Ctl, default value: 0x05 */
#define REG_DIV_CTL_MAIN 0x03f2
#define MSK_DIV_CTL_MAIN_PRE_DIV_CTL_MAIN 0x1c
#define MSK_DIV_CTL_MAIN_FB_DIV_CTL_MAIN 0x03
/* MHL Capability 1st Byte, default value: 0x00 */
#define REG_MHL_DEVCAP_0 0x0400
/* MHL Interrupt 1st Byte, default value: 0x00 */
#define REG_MHL_INT_0 0x0420
/* Device Status 1st byte, default value: 0x00 */
#define REG_MHL_STAT_0 0x0430
/* CBUS Scratch Pad 1st Byte, default value: 0x00 */
#define REG_MHL_SCRPAD_0 0x0440
/* MHL Extended Capability 1st Byte, default value: 0x00 */
#define REG_MHL_EXTDEVCAP_0 0x0480
/* Device Extended Status 1st byte, default value: 0x00 */
#define REG_MHL_EXTSTAT_0 0x0490
/* TPI DTD Byte2, default value: 0x00 */
#define REG_TPI_DTD_B2 0x0602
#define VAL_TPI_QUAN_RANGE_LIMITED 0x01
#define VAL_TPI_QUAN_RANGE_FULL 0x02
#define VAL_TPI_FORMAT_RGB 0x00
#define VAL_TPI_FORMAT_YCBCR444 0x01
#define VAL_TPI_FORMAT_YCBCR422 0x02
#define VAL_TPI_FORMAT_INTERNAL_RGB 0x03
#define VAL_TPI_FORMAT(_fmt, _qr) \
(VAL_TPI_FORMAT_##_fmt | (VAL_TPI_QUAN_RANGE_##_qr << 2))
/* Input Format, default value: 0x00 */
#define REG_TPI_INPUT 0x0609
#define BIT_TPI_INPUT_EXTENDEDBITMODE BIT(7)
#define BIT_TPI_INPUT_ENDITHER BIT(6)
#define MSK_TPI_INPUT_INPUT_QUAN_RANGE 0x0c
#define MSK_TPI_INPUT_INPUT_FORMAT 0x03
/* Output Format, default value: 0x00 */
#define REG_TPI_OUTPUT 0x060a
#define BIT_TPI_OUTPUT_CSCMODE709 BIT(4)
#define MSK_TPI_OUTPUT_OUTPUT_QUAN_RANGE 0x0c
#define MSK_TPI_OUTPUT_OUTPUT_FORMAT 0x03
/* TPI AVI Check Sum, default value: 0x00 */
#define REG_TPI_AVI_CHSUM 0x060c
/* TPI System Control, default value: 0x00 */
#define REG_TPI_SC 0x061a
#define BIT_TPI_SC_TPI_UPDATE_FLG BIT(7)
#define BIT_TPI_SC_TPI_REAUTH_CTL BIT(6)
#define BIT_TPI_SC_TPI_OUTPUT_MODE_1 BIT(5)
#define BIT_TPI_SC_REG_TMDS_OE_POWER_DOWN BIT(4)
#define BIT_TPI_SC_TPI_AV_MUTE BIT(3)
#define BIT_TPI_SC_DDC_GPU_REQUEST BIT(2)
#define BIT_TPI_SC_DDC_TPI_SW BIT(1)
#define BIT_TPI_SC_TPI_OUTPUT_MODE_0_HDMI BIT(0)
/* TPI COPP Query Data, default value: 0x00 */
#define REG_TPI_COPP_DATA1 0x0629
#define BIT_TPI_COPP_DATA1_COPP_GPROT BIT(7)
#define BIT_TPI_COPP_DATA1_COPP_LPROT BIT(6)
#define MSK_TPI_COPP_DATA1_COPP_LINK_STATUS 0x30
#define VAL_TPI_COPP_LINK_STATUS_NORMAL 0x00
#define VAL_TPI_COPP_LINK_STATUS_LINK_LOST 0x10
#define VAL_TPI_COPP_LINK_STATUS_RENEGOTIATION_REQ 0x20
#define VAL_TPI_COPP_LINK_STATUS_LINK_SUSPENDED 0x30
#define BIT_TPI_COPP_DATA1_COPP_HDCP_REP BIT(3)
#define BIT_TPI_COPP_DATA1_COPP_CONNTYPE_0 BIT(2)
#define BIT_TPI_COPP_DATA1_COPP_PROTYPE BIT(1)
#define BIT_TPI_COPP_DATA1_COPP_CONNTYPE_1 BIT(0)
/* TPI COPP Control Data, default value: 0x00 */
#define REG_TPI_COPP_DATA2 0x062a
#define BIT_TPI_COPP_DATA2_INTR_ENCRYPTION BIT(5)
#define BIT_TPI_COPP_DATA2_KSV_FORWARD BIT(4)
#define BIT_TPI_COPP_DATA2_INTERM_RI_CHECK_EN BIT(3)
#define BIT_TPI_COPP_DATA2_DOUBLE_RI_CHECK BIT(2)
#define BIT_TPI_COPP_DATA2_DDC_SHORT_RI_RD BIT(1)
#define BIT_TPI_COPP_DATA2_COPP_PROTLEVEL BIT(0)
/* TPI Interrupt Enable, default value: 0x00 */
#define REG_TPI_INTR_EN 0x063c
/* TPI Interrupt Status Low Byte, default value: 0x00 */
#define REG_TPI_INTR_ST0 0x063d
#define BIT_TPI_INTR_ST0_TPI_AUTH_CHNGE_STAT BIT(7)
#define BIT_TPI_INTR_ST0_TPI_V_RDY_STAT BIT(6)
#define BIT_TPI_INTR_ST0_TPI_COPP_CHNGE_STAT BIT(5)
#define BIT_TPI_INTR_ST0_KSV_FIFO_FIRST_STAT BIT(3)
#define BIT_TPI_INTR_ST0_READ_BKSV_BCAPS_DONE_STAT BIT(2)
#define BIT_TPI_INTR_ST0_READ_BKSV_BCAPS_ERR_STAT BIT(1)
#define BIT_TPI_INTR_ST0_READ_BKSV_ERR_STAT BIT(0)
/* TPI DS BCAPS Status, default value: 0x00 */
#define REG_TPI_DS_BCAPS 0x0644
/* TPI BStatus1, default value: 0x00 */
#define REG_TPI_BSTATUS1 0x0645
#define BIT_TPI_BSTATUS1_DS_DEV_EXCEED BIT(7)
#define MSK_TPI_BSTATUS1_DS_DEV_CNT 0x7f
/* TPI BStatus2, default value: 0x10 */
#define REG_TPI_BSTATUS2 0x0646
#define MSK_TPI_BSTATUS2_DS_BSTATUS 0xe0
#define BIT_TPI_BSTATUS2_DS_HDMI_MODE BIT(4)
#define BIT_TPI_BSTATUS2_DS_CASC_EXCEED BIT(3)
#define MSK_TPI_BSTATUS2_DS_DEPTH 0x07
/* TPI HW Optimization Control #3, default value: 0x00 */
#define REG_TPI_HW_OPT3 0x06bb
#define BIT_TPI_HW_OPT3_DDC_DEBUG BIT(7)
#define BIT_TPI_HW_OPT3_RI_CHECK_SKIP BIT(3)
#define BIT_TPI_HW_OPT3_TPI_DDC_BURST_MODE BIT(2)
#define MSK_TPI_HW_OPT3_TPI_DDC_REQ_LEVEL 0x03
/* TPI Info Frame Select, default value: 0x00 */
#define REG_TPI_INFO_FSEL 0x06bf
#define BIT_TPI_INFO_FSEL_EN BIT(7)
#define BIT_TPI_INFO_FSEL_RPT BIT(6)
#define BIT_TPI_INFO_FSEL_READ_FLAG BIT(5)
#define MSK_TPI_INFO_FSEL_PKT 0x07
#define VAL_TPI_INFO_FSEL_AVI 0x00
#define VAL_TPI_INFO_FSEL_SPD 0x01
#define VAL_TPI_INFO_FSEL_AUD 0x02
#define VAL_TPI_INFO_FSEL_MPG 0x03
#define VAL_TPI_INFO_FSEL_GEN 0x04
#define VAL_TPI_INFO_FSEL_GEN2 0x05
#define VAL_TPI_INFO_FSEL_VSI 0x06
/* TPI Info Byte #0, default value: 0x00 */
#define REG_TPI_INFO_B0 0x06c0
/* CoC Status, default value: 0x00 */
#define REG_COC_STAT_0 0x0700
#define BIT_COC_STAT_0_PLL_LOCKED BIT(7)
#define MSK_COC_STAT_0_FSM_STATE 0x0f
#define REG_COC_STAT_1 0x0701
#define REG_COC_STAT_2 0x0702
#define REG_COC_STAT_3 0x0703
#define REG_COC_STAT_4 0x0704
#define REG_COC_STAT_5 0x0705
/* CoC 1st Ctl, default value: 0x40 */
#define REG_COC_CTL0 0x0710
/* CoC 2nd Ctl, default value: 0x0a */
#define REG_COC_CTL1 0x0711
#define MSK_COC_CTL1_COC_CTRL1_7_6 0xc0
#define MSK_COC_CTL1_COC_CTRL1_5_0 0x3f
/* CoC 3rd Ctl, default value: 0x14 */
#define REG_COC_CTL2 0x0712
#define MSK_COC_CTL2_COC_CTRL2_7_6 0xc0
#define MSK_COC_CTL2_COC_CTRL2_5_0 0x3f
/* CoC 4th Ctl, default value: 0x40 */
#define REG_COC_CTL3 0x0713
#define BIT_COC_CTL3_COC_CTRL3_7 BIT(7)
#define MSK_COC_CTL3_COC_CTRL3_6_0 0x7f
/* CoC 7th Ctl, default value: 0x00 */
#define REG_COC_CTL6 0x0716
#define BIT_COC_CTL6_COC_CTRL6_7 BIT(7)
#define BIT_COC_CTL6_COC_CTRL6_6 BIT(6)
#define MSK_COC_CTL6_COC_CTRL6_5_0 0x3f
/* CoC 8th Ctl, default value: 0x06 */
#define REG_COC_CTL7 0x0717
#define BIT_COC_CTL7_COC_CTRL7_7 BIT(7)
#define BIT_COC_CTL7_COC_CTRL7_6 BIT(6)
#define BIT_COC_CTL7_COC_CTRL7_5 BIT(5)
#define MSK_COC_CTL7_COC_CTRL7_4_3 0x18
#define MSK_COC_CTL7_COC_CTRL7_2_0 0x07
/* CoC 10th Ctl, default value: 0x00 */
#define REG_COC_CTL9 0x0719
/* CoC 11th Ctl, default value: 0x00 */
#define REG_COC_CTLA 0x071a
/* CoC 12th Ctl, default value: 0x00 */
#define REG_COC_CTLB 0x071b
/* CoC 13th Ctl, default value: 0x0f */
#define REG_COC_CTLC 0x071c
/* CoC 14th Ctl, default value: 0x0a */
#define REG_COC_CTLD 0x071d
#define BIT_COC_CTLD_COC_CTRLD_7 BIT(7)
#define MSK_COC_CTLD_COC_CTRLD_6_0 0x7f
/* CoC 15th Ctl, default value: 0x0a */
#define REG_COC_CTLE 0x071e
#define BIT_COC_CTLE_COC_CTRLE_7 BIT(7)
#define MSK_COC_CTLE_COC_CTRLE_6_0 0x7f
/* CoC 16th Ctl, default value: 0x00 */
#define REG_COC_CTLF 0x071f
#define MSK_COC_CTLF_COC_CTRLF_7_3 0xf8
#define MSK_COC_CTLF_COC_CTRLF_2_0 0x07
/* CoC 18th Ctl, default value: 0x32 */
#define REG_COC_CTL11 0x0721
#define MSK_COC_CTL11_COC_CTRL11_7_4 0xf0
#define MSK_COC_CTL11_COC_CTRL11_3_0 0x0f
/* CoC 21st Ctl, default value: 0x00 */
#define REG_COC_CTL14 0x0724
#define MSK_COC_CTL14_COC_CTRL14_7_4 0xf0
#define MSK_COC_CTL14_COC_CTRL14_3_0 0x0f
/* CoC 22nd Ctl, default value: 0x00 */
#define REG_COC_CTL15 0x0725
#define BIT_COC_CTL15_COC_CTRL15_7 BIT(7)
#define MSK_COC_CTL15_COC_CTRL15_6_4 0x70
#define MSK_COC_CTL15_COC_CTRL15_3_0 0x0f
/* CoC Interrupt, default value: 0x00 */
#define REG_COC_INTR 0x0726
/* CoC Interrupt Mask, default value: 0x00 */
#define REG_COC_INTR_MASK 0x0727
#define BIT_COC_PLL_LOCK_STATUS_CHANGE BIT(0)
#define BIT_COC_CALIBRATION_DONE BIT(1)
/* CoC Misc Ctl, default value: 0x00 */
#define REG_COC_MISC_CTL0 0x0728
#define BIT_COC_MISC_CTL0_FSM_MON BIT(7)
/* CoC 24th Ctl, default value: 0x00 */
#define REG_COC_CTL17 0x072a
#define MSK_COC_CTL17_COC_CTRL17_7_4 0xf0
#define MSK_COC_CTL17_COC_CTRL17_3_0 0x0f
/* CoC 25th Ctl, default value: 0x00 */
#define REG_COC_CTL18 0x072b
#define MSK_COC_CTL18_COC_CTRL18_7_4 0xf0
#define MSK_COC_CTL18_COC_CTRL18_3_0 0x0f
/* CoC 26th Ctl, default value: 0x00 */
#define REG_COC_CTL19 0x072c
#define MSK_COC_CTL19_COC_CTRL19_7_4 0xf0
#define MSK_COC_CTL19_COC_CTRL19_3_0 0x0f
/* CoC 27th Ctl, default value: 0x00 */
#define REG_COC_CTL1A 0x072d
#define MSK_COC_CTL1A_COC_CTRL1A_7_2 0xfc
#define MSK_COC_CTL1A_COC_CTRL1A_1_0 0x03
/* DoC 9th Status, default value: 0x00 */
#define REG_DOC_STAT_8 0x0740
/* DoC 10th Status, default value: 0x00 */
#define REG_DOC_STAT_9 0x0741
/* DoC 5th CFG, default value: 0x00 */
#define REG_DOC_CFG4 0x074e
#define MSK_DOC_CFG4_DBG_STATE_DOC_FSM 0x0f
/* DoC 1st Ctl, default value: 0x40 */
#define REG_DOC_CTL0 0x0751
/* DoC 7th Ctl, default value: 0x00 */
#define REG_DOC_CTL6 0x0757
#define BIT_DOC_CTL6_DOC_CTRL6_7 BIT(7)
#define BIT_DOC_CTL6_DOC_CTRL6_6 BIT(6)
#define MSK_DOC_CTL6_DOC_CTRL6_5_4 0x30
#define MSK_DOC_CTL6_DOC_CTRL6_3_0 0x0f
/* DoC 8th Ctl, default value: 0x00 */
#define REG_DOC_CTL7 0x0758
#define BIT_DOC_CTL7_DOC_CTRL7_7 BIT(7)
#define BIT_DOC_CTL7_DOC_CTRL7_6 BIT(6)
#define BIT_DOC_CTL7_DOC_CTRL7_5 BIT(5)
#define MSK_DOC_CTL7_DOC_CTRL7_4_3 0x18
#define MSK_DOC_CTL7_DOC_CTRL7_2_0 0x07
/* DoC 9th Ctl, default value: 0x00 */
#define REG_DOC_CTL8 0x076c
#define BIT_DOC_CTL8_DOC_CTRL8_7 BIT(7)
#define MSK_DOC_CTL8_DOC_CTRL8_6_4 0x70
#define MSK_DOC_CTL8_DOC_CTRL8_3_2 0x0c
#define MSK_DOC_CTL8_DOC_CTRL8_1_0 0x03
/* DoC 10th Ctl, default value: 0x00 */
#define REG_DOC_CTL9 0x076d
/* DoC 11th Ctl, default value: 0x00 */
#define REG_DOC_CTLA 0x076e
/* DoC 15th Ctl, default value: 0x00 */
#define REG_DOC_CTLE 0x0772
#define BIT_DOC_CTLE_DOC_CTRLE_7 BIT(7)
#define BIT_DOC_CTLE_DOC_CTRLE_6 BIT(6)
#define MSK_DOC_CTLE_DOC_CTRLE_5_4 0x30
#define MSK_DOC_CTLE_DOC_CTRLE_3_0 0x0f
/* Interrupt Mask 1st, default value: 0x00 */
#define REG_MHL_INT_0_MASK 0x0580
/* Interrupt Mask 2nd, default value: 0x00 */
#define REG_MHL_INT_1_MASK 0x0581
/* Interrupt Mask 3rd, default value: 0x00 */
#define REG_MHL_INT_2_MASK 0x0582
/* Interrupt Mask 4th, default value: 0x00 */
#define REG_MHL_INT_3_MASK 0x0583
/* MDT Receive Time Out, default value: 0x00 */
#define REG_MDT_RCV_TIMEOUT 0x0584
/* MDT Transmit Time Out, default value: 0x00 */
#define REG_MDT_XMIT_TIMEOUT 0x0585
/* MDT Receive Control, default value: 0x00 */
#define REG_MDT_RCV_CTRL 0x0586
#define BIT_MDT_RCV_CTRL_MDT_RCV_EN BIT(7)
#define BIT_MDT_RCV_CTRL_MDT_DELAY_RCV_EN BIT(6)
#define BIT_MDT_RCV_CTRL_MDT_RFIFO_OVER_WR_EN BIT(4)
#define BIT_MDT_RCV_CTRL_MDT_XFIFO_OVER_WR_EN BIT(3)
#define BIT_MDT_RCV_CTRL_MDT_DISABLE BIT(2)
#define BIT_MDT_RCV_CTRL_MDT_RFIFO_CLR_ALL BIT(1)
#define BIT_MDT_RCV_CTRL_MDT_RFIFO_CLR_CUR BIT(0)
/* MDT Receive Read Port, default value: 0x00 */
#define REG_MDT_RCV_READ_PORT 0x0587
/* MDT Transmit Control, default value: 0x70 */
#define REG_MDT_XMIT_CTRL 0x0588
#define BIT_MDT_XMIT_CTRL_EN BIT(7)
#define BIT_MDT_XMIT_CTRL_CMD_MERGE_EN BIT(6)
#define BIT_MDT_XMIT_CTRL_FIXED_BURST_LEN BIT(5)
#define BIT_MDT_XMIT_CTRL_FIXED_AID BIT(4)
#define BIT_MDT_XMIT_CTRL_SINGLE_RUN_EN BIT(3)
#define BIT_MDT_XMIT_CTRL_CLR_ABORT_WAIT BIT(2)
#define BIT_MDT_XMIT_CTRL_XFIFO_CLR_ALL BIT(1)
#define BIT_MDT_XMIT_CTRL_XFIFO_CLR_CUR BIT(0)
/* MDT Receive WRITE Port, default value: 0x00 */
#define REG_MDT_XMIT_WRITE_PORT 0x0589
/* MDT RFIFO Status, default value: 0x00 */
#define REG_MDT_RFIFO_STAT 0x058a
#define MSK_MDT_RFIFO_STAT_MDT_RFIFO_CNT 0xe0
#define MSK_MDT_RFIFO_STAT_MDT_RFIFO_CUR_BYTE_CNT 0x1f
/* MDT XFIFO Status, default value: 0x80 */
#define REG_MDT_XFIFO_STAT 0x058b
#define MSK_MDT_XFIFO_STAT_MDT_XFIFO_LEVEL_AVAIL 0xe0
#define BIT_MDT_XFIFO_STAT_MDT_XMIT_PRE_HS_EN BIT(4)
#define MSK_MDT_XFIFO_STAT_MDT_WRITE_BURST_LEN 0x0f
/* MDT Interrupt 0, default value: 0x0c */
#define REG_MDT_INT_0 0x058c
#define BIT_MDT_RFIFO_DATA_RDY BIT(0)
#define BIT_MDT_IDLE_AFTER_HAWB_DISABLE BIT(2)
#define BIT_MDT_XFIFO_EMPTY BIT(3)
/* MDT Interrupt 0 Mask, default value: 0x00 */
#define REG_MDT_INT_0_MASK 0x058d
/* MDT Interrupt 1, default value: 0x00 */
#define REG_MDT_INT_1 0x058e
#define BIT_MDT_RCV_TIMEOUT BIT(0)
#define BIT_MDT_RCV_SM_ABORT_PKT_RCVD BIT(1)
#define BIT_MDT_RCV_SM_ERROR BIT(2)
#define BIT_MDT_XMIT_TIMEOUT BIT(5)
#define BIT_MDT_XMIT_SM_ABORT_PKT_RCVD BIT(6)
#define BIT_MDT_XMIT_SM_ERROR BIT(7)
/* MDT Interrupt 1 Mask, default value: 0x00 */
#define REG_MDT_INT_1_MASK 0x058f
/* CBUS Vendor ID, default value: 0x01 */
#define REG_CBUS_VENDOR_ID 0x0590
/* CBUS Connection Status, default value: 0x00 */
#define REG_CBUS_STATUS 0x0591
#define BIT_CBUS_STATUS_MHL_CABLE_PRESENT BIT(4)
#define BIT_CBUS_STATUS_MSC_HB_SUCCESS BIT(3)
#define BIT_CBUS_STATUS_CBUS_HPD BIT(2)
#define BIT_CBUS_STATUS_MHL_MODE BIT(1)
#define BIT_CBUS_STATUS_CBUS_CONNECTED BIT(0)
/* CBUS Interrupt 1st, default value: 0x00 */
#define REG_CBUS_INT_0 0x0592
#define BIT_CBUS_MSC_MT_DONE_NACK BIT(7)
#define BIT_CBUS_MSC_MR_SET_INT BIT(6)
#define BIT_CBUS_MSC_MR_WRITE_BURST BIT(5)
#define BIT_CBUS_MSC_MR_MSC_MSG BIT(4)
#define BIT_CBUS_MSC_MR_WRITE_STAT BIT(3)
#define BIT_CBUS_HPD_CHG BIT(2)
#define BIT_CBUS_MSC_MT_DONE BIT(1)
#define BIT_CBUS_CNX_CHG BIT(0)
/* CBUS Interrupt Mask 1st, default value: 0x00 */
#define REG_CBUS_INT_0_MASK 0x0593
/* CBUS Interrupt 2nd, default value: 0x00 */
#define REG_CBUS_INT_1 0x0594
#define BIT_CBUS_CMD_ABORT BIT(6)
#define BIT_CBUS_MSC_ABORT_RCVD BIT(3)
#define BIT_CBUS_DDC_ABORT BIT(2)
#define BIT_CBUS_CEC_ABORT BIT(1)
/* CBUS Interrupt Mask 2nd, default value: 0x00 */
#define REG_CBUS_INT_1_MASK 0x0595
/* CBUS DDC Abort Interrupt, default value: 0x00 */
#define REG_DDC_ABORT_INT 0x0598
/* CBUS DDC Abort Interrupt Mask, default value: 0x00 */
#define REG_DDC_ABORT_INT_MASK 0x0599
/* CBUS MSC Requester Abort Interrupt, default value: 0x00 */
#define REG_MSC_MT_ABORT_INT 0x059a
/* CBUS MSC Requester Abort Interrupt Mask, default value: 0x00 */
#define REG_MSC_MT_ABORT_INT_MASK 0x059b
/* CBUS MSC Responder Abort Interrupt, default value: 0x00 */
#define REG_MSC_MR_ABORT_INT 0x059c
/* CBUS MSC Responder Abort Interrupt Mask, default value: 0x00 */
#define REG_MSC_MR_ABORT_INT_MASK 0x059d
/* CBUS RX DISCOVERY interrupt, default value: 0x00 */
#define REG_CBUS_RX_DISC_INT0 0x059e
/* CBUS RX DISCOVERY Interrupt Mask, default value: 0x00 */
#define REG_CBUS_RX_DISC_INT0_MASK 0x059f
/* CBUS_Link_Layer Control #8, default value: 0x00 */
#define REG_CBUS_LINK_CTRL_8 0x05a7
/* MDT State Machine Status, default value: 0x00 */
#define REG_MDT_SM_STAT 0x05b5
#define MSK_MDT_SM_STAT_MDT_RCV_STATE 0xf0
#define MSK_MDT_SM_STAT_MDT_XMIT_STATE 0x0f
/* CBUS MSC command trigger, default value: 0x00 */
#define REG_MSC_COMMAND_START 0x05b8
#define BIT_MSC_COMMAND_START_DEBUG BIT(5)
#define BIT_MSC_COMMAND_START_WRITE_BURST BIT(4)
#define BIT_MSC_COMMAND_START_WRITE_STAT BIT(3)
#define BIT_MSC_COMMAND_START_READ_DEVCAP BIT(2)
#define BIT_MSC_COMMAND_START_MSC_MSG BIT(1)
#define BIT_MSC_COMMAND_START_PEER BIT(0)
/* CBUS MSC Command/Offset, default value: 0x00 */
#define REG_MSC_CMD_OR_OFFSET 0x05b9
/* CBUS MSC Transmit Data */
#define REG_MSC_1ST_TRANSMIT_DATA 0x05ba
#define REG_MSC_2ND_TRANSMIT_DATA 0x05bb
/* CBUS MSC Requester Received Data */
#define REG_MSC_MT_RCVD_DATA0 0x05bc
#define REG_MSC_MT_RCVD_DATA1 0x05bd
/* CBUS MSC Responder MSC_MSG Received Data */
#define REG_MSC_MR_MSC_MSG_RCVD_1ST_DATA 0x05bf
#define REG_MSC_MR_MSC_MSG_RCVD_2ND_DATA 0x05c0
/* CBUS MSC Heartbeat Control, default value: 0x27 */
#define REG_MSC_HEARTBEAT_CTRL 0x05c4
#define BIT_MSC_HEARTBEAT_CTRL_MSC_HB_EN BIT(7)
#define MSK_MSC_HEARTBEAT_CTRL_MSC_HB_FAIL_LIMIT 0x70
#define MSK_MSC_HEARTBEAT_CTRL_MSC_HB_PERIOD_MSB 0x0f
/* CBUS MSC Compatibility Control, default value: 0x02 */
#define REG_CBUS_MSC_COMPAT_CTRL 0x05c7
#define BIT_CBUS_MSC_COMPAT_CTRL_XDEVCAP_EN BIT(7)
#define BIT_CBUS_MSC_COMPAT_CTRL_DISABLE_MSC_ON_CBUS BIT(6)
#define BIT_CBUS_MSC_COMPAT_CTRL_DISABLE_DDC_ON_CBUS BIT(5)
#define BIT_CBUS_MSC_COMPAT_CTRL_DISABLE_GET_DDC_ERRORCODE BIT(3)
#define BIT_CBUS_MSC_COMPAT_CTRL_DISABLE_GET_VS1_ERRORCODE BIT(2)
/* CBUS3 Converter Control, default value: 0x24 */
#define REG_CBUS3_CNVT 0x05dc
#define MSK_CBUS3_CNVT_CBUS3_RETRYLMT 0xf0
#define MSK_CBUS3_CNVT_CBUS3_PEERTOUT_SEL 0x0c
#define BIT_CBUS3_CNVT_TEARCBUS_EN BIT(1)
#define BIT_CBUS3_CNVT_CBUS3CNVT_EN BIT(0)
/* Discovery Control1, default value: 0x24 */
#define REG_DISC_CTRL1 0x05e0
#define BIT_DISC_CTRL1_CBUS_INTR_EN BIT(7)
#define BIT_DISC_CTRL1_HB_ONLY BIT(6)
#define MSK_DISC_CTRL1_DISC_ATT 0x30
#define MSK_DISC_CTRL1_DISC_CYC 0x0c
#define BIT_DISC_CTRL1_DISC_EN BIT(0)
#define VAL_PUP_OFF 0
#define VAL_PUP_20K 1
#define VAL_PUP_5K 2
/* Discovery Control4, default value: 0x80 */
#define REG_DISC_CTRL4 0x05e3
#define MSK_DISC_CTRL4_CBUSDISC_PUP_SEL 0xc0
#define MSK_DISC_CTRL4_CBUSIDLE_PUP_SEL 0x30
#define VAL_DISC_CTRL4(pup_disc, pup_idle) (((pup_disc) << 6) | (pup_idle << 4))
/* Discovery Control5, default value: 0x03 */
#define REG_DISC_CTRL5 0x05e4
#define BIT_DISC_CTRL5_DSM_OVRIDE BIT(3)
#define MSK_DISC_CTRL5_CBUSMHL_PUP_SEL 0x03
/* Discovery Control8, default value: 0x81 */
#define REG_DISC_CTRL8 0x05e7
#define BIT_DISC_CTRL8_NOMHLINT_CLR_BYPASS BIT(7)
#define BIT_DISC_CTRL8_DELAY_CBUS_INTR_EN BIT(0)
/* Discovery Control9, default value: 0x54 */
#define REG_DISC_CTRL9 0x05e8
#define BIT_DISC_CTRL9_MHL3_RSEN_BYP BIT(7)
#define BIT_DISC_CTRL9_MHL3DISC_EN BIT(6)
#define BIT_DISC_CTRL9_WAKE_DRVFLT BIT(4)
#define BIT_DISC_CTRL9_NOMHL_EST BIT(3)
#define BIT_DISC_CTRL9_DISC_PULSE_PROCEED BIT(2)
#define BIT_DISC_CTRL9_WAKE_PULSE_BYPASS BIT(1)
#define BIT_DISC_CTRL9_VBUS_OUTPUT_CAPABILITY_SRC BIT(0)
/* Discovery Status1, default value: 0x00 */
#define REG_DISC_STAT1 0x05eb
#define BIT_DISC_STAT1_PSM_OVRIDE BIT(5)
#define MSK_DISC_STAT1_DISC_SM 0x0f
/* Discovery Status2, default value: 0x00 */
#define REG_DISC_STAT2 0x05ec
#define BIT_DISC_STAT2_CBUS_OE_POL BIT(6)
#define BIT_DISC_STAT2_CBUS_SATUS BIT(5)
#define BIT_DISC_STAT2_RSEN BIT(4)
#define MSK_DISC_STAT2_MHL_VRSN 0x0c
#define VAL_DISC_STAT2_DEFAULT 0x00
#define VAL_DISC_STAT2_MHL1_2 0x04
#define VAL_DISC_STAT2_MHL3 0x08
#define VAL_DISC_STAT2_RESERVED 0x0c
#define MSK_DISC_STAT2_RGND 0x03
#define VAL_RGND_OPEN 0x00
#define VAL_RGND_2K 0x01
#define VAL_RGND_1K 0x02
#define VAL_RGND_SHORT 0x03
/* Interrupt CBUS_reg1 INTR0, default value: 0x00 */
#define REG_CBUS_DISC_INTR0 0x05ed
#define BIT_RGND_READY_INT BIT(6)
#define BIT_CBUS_MHL12_DISCON_INT BIT(5)
#define BIT_CBUS_MHL3_DISCON_INT BIT(4)
#define BIT_NOT_MHL_EST_INT BIT(3)
#define BIT_MHL_EST_INT BIT(2)
#define BIT_MHL3_EST_INT BIT(1)
#define VAL_CBUS_MHL_DISCON (BIT_CBUS_MHL12_DISCON_INT \
| BIT_CBUS_MHL3_DISCON_INT \
| BIT_NOT_MHL_EST_INT)
/* Interrupt CBUS_reg1 INTR0 Mask, default value: 0x00 */
#define REG_CBUS_DISC_INTR0_MASK 0x05ee
#endif /* __SIL_SII8620_H__ */
Overall Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| Andrzej Hajda | 4105 | 100.00% | 6 | 100.00% |
| Total | 4105 | 100.00% | 6 | 100.00% |
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.