cregit-Linux how code gets into the kernel

Release 4.11 drivers/gpu/drm/vc4/vc4_dsi.c

Directory: drivers/gpu/drm/vc4
/*
 * Copyright (C) 2016 Broadcom
 *
 * This program is free software; you can redistribute it and/or modify it
 * under the terms of the GNU General Public License version 2 as published by
 * the Free Software Foundation.
 *
 * This program is distributed in the hope that it will be useful, but WITHOUT
 * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
 * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
 * more details.
 *
 * You should have received a copy of the GNU General Public License along with
 * this program.  If not, see <http://www.gnu.org/licenses/>.
 */

/**
 * DOC: VC4 DSI0/DSI1 module
 *
 * BCM2835 contains two DSI modules, DSI0 and DSI1.  DSI0 is a
 * single-lane DSI controller, while DSI1 is a more modern 4-lane DSI
 * controller.
 *
 * Most Raspberry Pi boards expose DSI1 as their "DISPLAY" connector,
 * while the compute module brings both DSI0 and DSI1 out.
 *
 * This driver has been tested for DSI1 video-mode display only
 * currently, with most of the information necessary for DSI0
 * hopefully present.
 */

#include "drm_atomic_helper.h"
#include "drm_crtc_helper.h"
#include "drm_edid.h"
#include "drm_mipi_dsi.h"
#include "drm_panel.h"
#include "linux/clk.h"
#include "linux/clk-provider.h"
#include "linux/completion.h"
#include "linux/component.h"
#include "linux/dmaengine.h"
#include "linux/i2c.h"
#include "linux/of_address.h"
#include "linux/of_platform.h"
#include "linux/pm_runtime.h"
#include "vc4_drv.h"
#include "vc4_regs.h"


#define DSI_CMD_FIFO_DEPTH  16

#define DSI_PIX_FIFO_DEPTH 256

#define DSI_PIX_FIFO_WIDTH   4


#define DSI0_CTRL		0x00

/* Command packet control. */

#define DSI0_TXPKT1C		0x04 
/* AKA PKTC */

#define DSI1_TXPKT1C		0x04

# define DSI_TXPKT1C_TRIG_CMD_MASK	VC4_MASK(31, 24)

# define DSI_TXPKT1C_TRIG_CMD_SHIFT	24

# define DSI_TXPKT1C_CMD_REPEAT_MASK	VC4_MASK(23, 10)

# define DSI_TXPKT1C_CMD_REPEAT_SHIFT	10


# define DSI_TXPKT1C_DISPLAY_NO_MASK	VC4_MASK(9, 8)

# define DSI_TXPKT1C_DISPLAY_NO_SHIFT	8
/* Short, trigger, BTA, or a long packet that fits all in CMDFIFO. */

# define DSI_TXPKT1C_DISPLAY_NO_SHORT		0
/* Primary display where cmdfifo provides part of the payload and
 * pixelvalve the rest.
 */

# define DSI_TXPKT1C_DISPLAY_NO_PRIMARY		1
/* Secondary display where cmdfifo provides part of the payload and
 * pixfifo the rest.
 */

# define DSI_TXPKT1C_DISPLAY_NO_SECONDARY	2


# define DSI_TXPKT1C_CMD_TX_TIME_MASK	VC4_MASK(7, 6)

# define DSI_TXPKT1C_CMD_TX_TIME_SHIFT	6


# define DSI_TXPKT1C_CMD_CTRL_MASK	VC4_MASK(5, 4)

# define DSI_TXPKT1C_CMD_CTRL_SHIFT	4
/* Command only.  Uses TXPKT1H and DISPLAY_NO */

# define DSI_TXPKT1C_CMD_CTRL_TX	0
/* Command with BTA for either ack or read data. */

# define DSI_TXPKT1C_CMD_CTRL_RX	1
/* Trigger according to TRIG_CMD */

# define DSI_TXPKT1C_CMD_CTRL_TRIG	2
/* BTA alone for getting error status after a command, or a TE trigger
 * without a previous command.
 */

# define DSI_TXPKT1C_CMD_CTRL_BTA	3


# define DSI_TXPKT1C_CMD_MODE_LP	BIT(3)

# define DSI_TXPKT1C_CMD_TYPE_LONG	BIT(2)

# define DSI_TXPKT1C_CMD_TE_EN		BIT(1)

# define DSI_TXPKT1C_CMD_EN		BIT(0)

/* Command packet header. */

#define DSI0_TXPKT1H		0x08 
/* AKA PKTH */

#define DSI1_TXPKT1H		0x08

# define DSI_TXPKT1H_BC_CMDFIFO_MASK	VC4_MASK(31, 24)

# define DSI_TXPKT1H_BC_CMDFIFO_SHIFT	24

# define DSI_TXPKT1H_BC_PARAM_MASK	VC4_MASK(23, 8)

# define DSI_TXPKT1H_BC_PARAM_SHIFT	8

# define DSI_TXPKT1H_BC_DT_MASK		VC4_MASK(7, 0)

# define DSI_TXPKT1H_BC_DT_SHIFT	0


#define DSI0_RXPKT1H		0x0c 
/* AKA RX1_PKTH */

#define DSI1_RXPKT1H		0x14

# define DSI_RXPKT1H_CRC_ERR		BIT(31)

# define DSI_RXPKT1H_DET_ERR		BIT(30)

# define DSI_RXPKT1H_ECC_ERR		BIT(29)

# define DSI_RXPKT1H_COR_ERR		BIT(28)

# define DSI_RXPKT1H_INCOMP_PKT		BIT(25)

# define DSI_RXPKT1H_PKT_TYPE_LONG	BIT(24)
/* Byte count if DSI_RXPKT1H_PKT_TYPE_LONG */

# define DSI_RXPKT1H_BC_PARAM_MASK	VC4_MASK(23, 8)

# define DSI_RXPKT1H_BC_PARAM_SHIFT	8
/* Short return bytes if !DSI_RXPKT1H_PKT_TYPE_LONG */

# define DSI_RXPKT1H_SHORT_1_MASK	VC4_MASK(23, 16)

# define DSI_RXPKT1H_SHORT_1_SHIFT	16

# define DSI_RXPKT1H_SHORT_0_MASK	VC4_MASK(15, 8)

# define DSI_RXPKT1H_SHORT_0_SHIFT	8

# define DSI_RXPKT1H_DT_LP_CMD_MASK	VC4_MASK(7, 0)

# define DSI_RXPKT1H_DT_LP_CMD_SHIFT	0


#define DSI0_RXPKT2H		0x10 
/* AKA RX2_PKTH */

#define DSI1_RXPKT2H		0x18

# define DSI_RXPKT1H_DET_ERR		BIT(30)

# define DSI_RXPKT1H_ECC_ERR		BIT(29)

# define DSI_RXPKT1H_COR_ERR		BIT(28)

# define DSI_RXPKT1H_INCOMP_PKT		BIT(25)

# define DSI_RXPKT1H_BC_PARAM_MASK	VC4_MASK(23, 8)

# define DSI_RXPKT1H_BC_PARAM_SHIFT	8

# define DSI_RXPKT1H_DT_MASK		VC4_MASK(7, 0)

# define DSI_RXPKT1H_DT_SHIFT		0


#define DSI0_TXPKT_CMD_FIFO	0x14 
/* AKA CMD_DATAF */

#define DSI1_TXPKT_CMD_FIFO	0x1c


#define DSI0_DISP0_CTRL		0x18

# define DSI_DISP0_PIX_CLK_DIV_MASK	VC4_MASK(21, 13)

# define DSI_DISP0_PIX_CLK_DIV_SHIFT	13

# define DSI_DISP0_LP_STOP_CTRL_MASK	VC4_MASK(12, 11)

# define DSI_DISP0_LP_STOP_CTRL_SHIFT	11

# define DSI_DISP0_LP_STOP_DISABLE	0

# define DSI_DISP0_LP_STOP_PERLINE	1

# define DSI_DISP0_LP_STOP_PERFRAME	2

/* Transmit RGB pixels and null packets only during HACTIVE, instead
 * of going to LP-STOP.
 */

# define DSI_DISP_HACTIVE_NULL		BIT(10)
/* Transmit blanking packet only during vblank, instead of allowing LP-STOP. */

# define DSI_DISP_VBLP_CTRL		BIT(9)
/* Transmit blanking packet only during HFP, instead of allowing LP-STOP. */

# define DSI_DISP_HFP_CTRL		BIT(8)
/* Transmit blanking packet only during HBP, instead of allowing LP-STOP. */

# define DSI_DISP_HBP_CTRL		BIT(7)

# define DSI_DISP0_CHANNEL_MASK		VC4_MASK(6, 5)

# define DSI_DISP0_CHANNEL_SHIFT	5
/* Enables end events for HSYNC/VSYNC, not just start events. */

# define DSI_DISP0_ST_END		BIT(4)

# define DSI_DISP0_PFORMAT_MASK		VC4_MASK(3, 2)

# define DSI_DISP0_PFORMAT_SHIFT	2

# define DSI_PFORMAT_RGB565		0

# define DSI_PFORMAT_RGB666_PACKED	1

# define DSI_PFORMAT_RGB666		2

# define DSI_PFORMAT_RGB888		3
/* Default is VIDEO mode. */

# define DSI_DISP0_COMMAND_MODE		BIT(1)

# define DSI_DISP0_ENABLE		BIT(0)


#define DSI0_DISP1_CTRL		0x1c

#define DSI1_DISP1_CTRL		0x2c
/* Format of the data written to TXPKT_PIX_FIFO. */

# define DSI_DISP1_PFORMAT_MASK		VC4_MASK(2, 1)

# define DSI_DISP1_PFORMAT_SHIFT	1

# define DSI_DISP1_PFORMAT_16BIT	0

# define DSI_DISP1_PFORMAT_24BIT	1

# define DSI_DISP1_PFORMAT_32BIT_LE	2

# define DSI_DISP1_PFORMAT_32BIT_BE	3

/* DISP1 is always command mode. */

# define DSI_DISP1_ENABLE		BIT(0)


#define DSI0_TXPKT_PIX_FIFO		0x20 
/* AKA PIX_FIFO */


#define DSI0_INT_STAT		0x24

#define DSI0_INT_EN		0x28

# define DSI1_INT_PHY_D3_ULPS		BIT(30)

# define DSI1_INT_PHY_D3_STOP		BIT(29)

# define DSI1_INT_PHY_D2_ULPS		BIT(28)

# define DSI1_INT_PHY_D2_STOP		BIT(27)

# define DSI1_INT_PHY_D1_ULPS		BIT(26)

# define DSI1_INT_PHY_D1_STOP		BIT(25)

# define DSI1_INT_PHY_D0_ULPS		BIT(24)

# define DSI1_INT_PHY_D0_STOP		BIT(23)

# define DSI1_INT_FIFO_ERR		BIT(22)

# define DSI1_INT_PHY_DIR_RTF		BIT(21)

# define DSI1_INT_PHY_RXLPDT		BIT(20)

# define DSI1_INT_PHY_RXTRIG		BIT(19)

# define DSI1_INT_PHY_D0_LPDT		BIT(18)

# define DSI1_INT_PHY_DIR_FTR		BIT(17)

/* Signaled when the clock lane enters the given state. */

# define DSI1_INT_PHY_CLOCK_ULPS	BIT(16)

# define DSI1_INT_PHY_CLOCK_HS		BIT(15)

# define DSI1_INT_PHY_CLOCK_STOP	BIT(14)

/* Signaled on timeouts */

# define DSI1_INT_PR_TO			BIT(13)

# define DSI1_INT_TA_TO			BIT(12)

# define DSI1_INT_LPRX_TO		BIT(11)

# define DSI1_INT_HSTX_TO		BIT(10)

/* Contention on a line when trying to drive the line low */

# define DSI1_INT_ERR_CONT_LP1		BIT(9)

# define DSI1_INT_ERR_CONT_LP0		BIT(8)

/* Control error: incorrect line state sequence on data lane 0. */

# define DSI1_INT_ERR_CONTROL		BIT(7)
/* LPDT synchronization error (bits received not a multiple of 8. */


# define DSI1_INT_ERR_SYNC_ESC		BIT(6)
/* Signaled after receiving an error packet from the display in
 * response to a read.
 */

# define DSI1_INT_RXPKT2		BIT(5)
/* Signaled after receiving a packet.  The header and optional short
 * response will be in RXPKT1H, and a long response will be in the
 * RXPKT_FIFO.
 */

# define DSI1_INT_RXPKT1		BIT(4)

# define DSI1_INT_TXPKT2_DONE		BIT(3)

# define DSI1_INT_TXPKT2_END		BIT(2)
/* Signaled after all repeats of TXPKT1 are transferred. */

# define DSI1_INT_TXPKT1_DONE		BIT(1)
/* Signaled after each TXPKT1 repeat is scheduled. */

# define DSI1_INT_TXPKT1_END		BIT(0)


#define DSI1_INTERRUPTS_ALWAYS_ENABLED	(DSI1_INT_ERR_SYNC_ESC | \
                                         DSI1_INT_ERR_CONTROL |  \
                                         DSI1_INT_ERR_CONT_LP0 | \
                                         DSI1_INT_ERR_CONT_LP1 | \
                                         DSI1_INT_HSTX_TO |      \
                                         DSI1_INT_LPRX_TO |      \
                                         DSI1_INT_TA_TO |        \
                                         DSI1_INT_PR_TO)


#define DSI0_STAT		0x2c

#define DSI0_HSTX_TO_CNT	0x30

#define DSI0_LPRX_TO_CNT	0x34

#define DSI0_TA_TO_CNT		0x38

#define DSI0_PR_TO_CNT		0x3c

#define DSI0_PHYC		0x40

# define DSI1_PHYC_ESC_CLK_LPDT_MASK	VC4_MASK(25, 20)

# define DSI1_PHYC_ESC_CLK_LPDT_SHIFT	20

# define DSI1_PHYC_HS_CLK_CONTINUOUS	BIT(18)

# define DSI0_PHYC_ESC_CLK_LPDT_MASK	VC4_MASK(17, 12)

# define DSI0_PHYC_ESC_CLK_LPDT_SHIFT	12

# define DSI1_PHYC_CLANE_ULPS		BIT(17)

# define DSI1_PHYC_CLANE_ENABLE		BIT(16)

# define DSI_PHYC_DLANE3_ULPS		BIT(13)

# define DSI_PHYC_DLANE3_ENABLE		BIT(12)

# define DSI0_PHYC_HS_CLK_CONTINUOUS	BIT(10)

# define DSI0_PHYC_CLANE_ULPS		BIT(9)

# define DSI_PHYC_DLANE2_ULPS		BIT(9)

# define DSI0_PHYC_CLANE_ENABLE		BIT(8)

# define DSI_PHYC_DLANE2_ENABLE		BIT(8)

# define DSI_PHYC_DLANE1_ULPS		BIT(5)

# define DSI_PHYC_DLANE1_ENABLE		BIT(4)

# define DSI_PHYC_DLANE0_FORCE_STOP	BIT(2)

# define DSI_PHYC_DLANE0_ULPS		BIT(1)

# define DSI_PHYC_DLANE0_ENABLE		BIT(0)


#define DSI0_HS_CLT0		0x44

#define DSI0_HS_CLT1		0x48

#define DSI0_HS_CLT2		0x4c

#define DSI0_HS_DLT3		0x50

#define DSI0_HS_DLT4		0x54

#define DSI0_HS_DLT5		0x58

#define DSI0_HS_DLT6		0x5c

#define DSI0_HS_DLT7		0x60


#define DSI0_PHY_AFEC0		0x64

# define DSI0_PHY_AFEC0_DDR2CLK_EN		BIT(26)

# define DSI0_PHY_AFEC0_DDRCLK_EN		BIT(25)

# define DSI0_PHY_AFEC0_LATCH_ULPS		BIT(24)

# define DSI1_PHY_AFEC0_IDR_DLANE3_MASK		VC4_MASK(31, 29)

# define DSI1_PHY_AFEC0_IDR_DLANE3_SHIFT	29

# define DSI1_PHY_AFEC0_IDR_DLANE2_MASK		VC4_MASK(28, 26)

# define DSI1_PHY_AFEC0_IDR_DLANE2_SHIFT	26

# define DSI1_PHY_AFEC0_IDR_DLANE1_MASK		VC4_MASK(27, 23)

# define DSI1_PHY_AFEC0_IDR_DLANE1_SHIFT	23

# define DSI1_PHY_AFEC0_IDR_DLANE0_MASK		VC4_MASK(22, 20)

# define DSI1_PHY_AFEC0_IDR_DLANE0_SHIFT	20

# define DSI1_PHY_AFEC0_IDR_CLANE_MASK		VC4_MASK(19, 17)

# define DSI1_PHY_AFEC0_IDR_CLANE_SHIFT		17

# define DSI0_PHY_AFEC0_ACTRL_DLANE1_MASK	VC4_MASK(23, 20)

# define DSI0_PHY_AFEC0_ACTRL_DLANE1_SHIFT	20

# define DSI0_PHY_AFEC0_ACTRL_DLANE0_MASK	VC4_MASK(19, 16)

# define DSI0_PHY_AFEC0_ACTRL_DLANE0_SHIFT	16

# define DSI0_PHY_AFEC0_ACTRL_CLANE_MASK	VC4_MASK(15, 12)

# define DSI0_PHY_AFEC0_ACTRL_CLANE_SHIFT	12

# define DSI1_PHY_AFEC0_DDR2CLK_EN		BIT(16)

# define DSI1_PHY_AFEC0_DDRCLK_EN		BIT(15)

# define DSI1_PHY_AFEC0_LATCH_ULPS		BIT(14)

# define DSI1_PHY_AFEC0_RESET			BIT(13)

# define DSI1_PHY_AFEC0_PD			BIT(12)

# define DSI0_PHY_AFEC0_RESET			BIT(11)

# define DSI1_PHY_AFEC0_PD_BG			BIT(11)

# define DSI0_PHY_AFEC0_PD			BIT(10)

# define DSI1_PHY_AFEC0_PD_DLANE3		BIT(10)

# define DSI0_PHY_AFEC0_PD_BG			BIT(9)

# define DSI1_PHY_AFEC0_PD_DLANE2		BIT(9)

# define DSI0_PHY_AFEC0_PD_DLANE1		BIT(8)

# define DSI1_PHY_AFEC0_PD_DLANE1		BIT(8)

# define DSI_PHY_AFEC0_PTATADJ_MASK		VC4_MASK(7, 4)

# define DSI_PHY_AFEC0_PTATADJ_SHIFT		4

# define DSI_PHY_AFEC0_CTATADJ_MASK		VC4_MASK(3, 0)

# define DSI_PHY_AFEC0_CTATADJ_SHIFT		0


#define DSI0_PHY_AFEC1		0x68

# define DSI0_PHY_AFEC1_IDR_DLANE1_MASK		VC4_MASK(10, 8)

# define DSI0_PHY_AFEC1_IDR_DLANE1_SHIFT	8

# define DSI0_PHY_AFEC1_IDR_DLANE0_MASK		VC4_MASK(6, 4)

# define DSI0_PHY_AFEC1_IDR_DLANE0_SHIFT	4

# define DSI0_PHY_AFEC1_IDR_CLANE_MASK		VC4_MASK(2, 0)

# define DSI0_PHY_AFEC1_IDR_CLANE_SHIFT		0


#define DSI0_TST_SEL		0x6c

#define DSI0_TST_MON		0x70

#define DSI0_ID			0x74

# define DSI_ID_VALUE		0x00647369


#define DSI1_CTRL		0x00

# define DSI_CTRL_HS_CLKC_MASK		VC4_MASK(15, 14)

# define DSI_CTRL_HS_CLKC_SHIFT		14

# define DSI_CTRL_HS_CLKC_BYTE		0

# define DSI_CTRL_HS_CLKC_DDR2		1

# define DSI_CTRL_HS_CLKC_DDR		2


# define DSI_CTRL_RX_LPDT_EOT_DISABLE	BIT(13)

# define DSI_CTRL_LPDT_EOT_DISABLE	BIT(12)

# define DSI_CTRL_HSDT_EOT_DISABLE	BIT(11)

# define DSI_CTRL_SOFT_RESET_CFG	BIT(10)

# define DSI_CTRL_CAL_BYTE		BIT(9)

# define DSI_CTRL_INV_BYTE		BIT(8)

# define DSI_CTRL_CLR_LDF		BIT(7)

# define DSI0_CTRL_CLR_PBCF		BIT(6)

# define DSI1_CTRL_CLR_RXF		BIT(6)

# define DSI0_CTRL_CLR_CPBCF		BIT(5)

# define DSI1_CTRL_CLR_PDF		BIT(5)

# define DSI0_CTRL_CLR_PDF		BIT(4)

# define DSI1_CTRL_CLR_CDF		BIT(4)

# define DSI0_CTRL_CLR_CDF		BIT(3)

# define DSI0_CTRL_CTRL2		BIT(2)

# define DSI1_CTRL_DISABLE_DISP_CRCC	BIT(2)

# define DSI0_CTRL_CTRL1		BIT(1)

# define DSI1_CTRL_DISABLE_DISP_ECCC	BIT(1)

# define DSI0_CTRL_CTRL0		BIT(0)

# define DSI1_CTRL_EN			BIT(0)

# define DSI0_CTRL_RESET_FIFOS		(DSI_CTRL_CLR_LDF | \
                                         DSI0_CTRL_CLR_PBCF | \
                                         DSI0_CTRL_CLR_CPBCF |  \
                                         DSI0_CTRL_CLR_PDF | \
                                         DSI0_CTRL_CLR_CDF)

# define DSI1_CTRL_RESET_FIFOS		(DSI_CTRL_CLR_LDF | \
                                         DSI1_CTRL_CLR_RXF | \
                                         DSI1_CTRL_CLR_PDF | \
                                         DSI1_CTRL_CLR_CDF)


#define DSI1_TXPKT2C		0x0c

#define DSI1_TXPKT2H		0x10

#define DSI1_TXPKT_PIX_FIFO	0x20

#define DSI1_RXPKT_FIFO		0x24

#define DSI1_DISP0_CTRL		0x28

#define DSI1_INT_STAT		0x30

#define DSI1_INT_EN		0x34
/* State reporting bits.  These mostly behave like INT_STAT, where
 * writing a 1 clears the bit.
 */

#define DSI1_STAT		0x38

# define DSI1_STAT_PHY_D3_ULPS		BIT(31)

# define DSI1_STAT_PHY_D3_STOP		BIT(30)

# define DSI1_STAT_PHY_D2_ULPS		BIT(29)

# define DSI1_STAT_PHY_D2_STOP		BIT(28)

# define DSI1_STAT_PHY_D1_ULPS		BIT(27)

# define DSI1_STAT_PHY_D1_STOP		BIT(26)

# define DSI1_STAT_PHY_D0_ULPS		BIT(25)

# define DSI1_STAT_PHY_D0_STOP		BIT(24)

# define DSI1_STAT_FIFO_ERR		BIT(23)

# define DSI1_STAT_PHY_RXLPDT		BIT(22)

# define DSI1_STAT_PHY_RXTRIG		BIT(21)

# define DSI1_STAT_PHY_D0_LPDT		BIT(20)
/* Set when in forward direction */

# define DSI1_STAT_PHY_DIR		BIT(19)

# define DSI1_STAT_PHY_CLOCK_ULPS	BIT(18)

# define DSI1_STAT_PHY_CLOCK_HS		BIT(17)

# define DSI1_STAT_PHY_CLOCK_STOP	BIT(16)

# define DSI1_STAT_PR_TO		BIT(15)

# define DSI1_STAT_TA_TO		BIT(14)

# define DSI1_STAT_LPRX_TO		BIT(13)

# define DSI1_STAT_HSTX_TO		BIT(12)

# define DSI1_STAT_ERR_CONT_LP1		BIT(11)

# define DSI1_STAT_ERR_CONT_LP0		BIT(10)

# define DSI1_STAT_ERR_CONTROL		BIT(9)

# define DSI1_STAT_ERR_SYNC_ESC		BIT(8)

# define DSI1_STAT_RXPKT2		BIT(7)

# define DSI1_STAT_RXPKT1		BIT(6)

# define DSI1_STAT_TXPKT2_BUSY		BIT(5)

# define DSI1_STAT_TXPKT2_DONE		BIT(4)

# define DSI1_STAT_TXPKT2_END		BIT(3)

# define DSI1_STAT_TXPKT1_BUSY		BIT(2)

# define DSI1_STAT_TXPKT1_DONE		BIT(1)

# define DSI1_STAT_TXPKT1_END		BIT(0)


#define DSI1_HSTX_TO_CNT	0x3c

#define DSI1_LPRX_TO_CNT	0x40

#define DSI1_TA_TO_CNT		0x44

#define DSI1_PR_TO_CNT		0x48

#define DSI1_PHYC		0x4c


#define DSI1_HS_CLT0		0x50

# define DSI_HS_CLT0_CZERO_MASK		VC4_MASK(26, 18)

# define DSI_HS_CLT0_CZERO_SHIFT	18

# define DSI_HS_CLT0_CPRE_MASK		VC4_MASK(17, 9)

# define DSI_HS_CLT0_CPRE_SHIFT		9

# define DSI_HS_CLT0_CPREP_MASK		VC4_MASK(8, 0)

# define DSI_HS_CLT0_CPREP_SHIFT	0


#define DSI1_HS_CLT1		0x54

# define DSI_HS_CLT1_CTRAIL_MASK	VC4_MASK(17, 9)

# define DSI_HS_CLT1_CTRAIL_SHIFT	9

# define DSI_HS_CLT1_CPOST_MASK		VC4_MASK(8, 0)

# define DSI_HS_CLT1_CPOST_SHIFT	0


#define DSI1_HS_CLT2		0x58

# define DSI_HS_CLT2_WUP_MASK		VC4_MASK(23, 0)

# define DSI_HS_CLT2_WUP_SHIFT		0


#define DSI1_HS_DLT3		0x5c

# define DSI_HS_DLT3_EXIT_MASK		VC4_MASK(26, 18)

# define DSI_HS_DLT3_EXIT_SHIFT		18

# define DSI_HS_DLT3_ZERO_MASK		VC4_MASK(17, 9)

# define DSI_HS_DLT3_ZERO_SHIFT		9

# define DSI_HS_DLT3_PRE_MASK		VC4_MASK(8, 0)

# define DSI_HS_DLT3_PRE_SHIFT		0


#define DSI1_HS_DLT4		0x60

# define DSI_HS_DLT4_ANLAT_MASK		VC4_MASK(22, 18)

# define DSI_HS_DLT4_ANLAT_SHIFT	18

# define DSI_HS_DLT4_TRAIL_MASK		VC4_MASK(17, 9)

# define DSI_HS_DLT4_TRAIL_SHIFT	9

# define DSI_HS_DLT4_LPX_MASK		VC4_MASK(8, 0)

# define DSI_HS_DLT4_LPX_SHIFT		0


#define DSI1_HS_DLT5		0x64

# define DSI_HS_DLT5_INIT_MASK		VC4_MASK(23, 0)

# define DSI_HS_DLT5_INIT_SHIFT		0


#define DSI1_HS_DLT6		0x68

# define DSI_HS_DLT6_TA_GET_MASK	VC4_MASK(31, 24)

# define DSI_HS_DLT6_TA_GET_SHIFT	24

# define DSI_HS_DLT6_TA_SURE_MASK	VC4_MASK(23, 16)

# define DSI_HS_DLT6_TA_SURE_SHIFT	16

# define DSI_HS_DLT6_TA_GO_MASK		VC4_MASK(15, 8)

# define DSI_HS_DLT6_TA_GO_SHIFT	8

# define DSI_HS_DLT6_LP_LPX_MASK	VC4_MASK(7, 0)

# define DSI_HS_DLT6_LP_LPX_SHIFT	0


#define DSI1_HS_DLT7		0x6c

# define DSI_HS_DLT7_LP_WUP_MASK	VC4_MASK(23, 0)

# define DSI_HS_DLT7_LP_WUP_SHIFT	0


#define DSI1_PHY_AFEC0		0x70


#define DSI1_PHY_AFEC1		0x74

# define DSI1_PHY_AFEC1_ACTRL_DLANE3_MASK	VC4_MASK(19, 16)

# define DSI1_PHY_AFEC1_ACTRL_DLANE3_SHIFT	16

# define DSI1_PHY_AFEC1_ACTRL_DLANE2_MASK	VC4_MASK(15, 12)

# define DSI1_PHY_AFEC1_ACTRL_DLANE2_SHIFT	12

# define DSI1_PHY_AFEC1_ACTRL_DLANE1_MASK	VC4_MASK(11, 8)

# define DSI1_PHY_AFEC1_ACTRL_DLANE1_SHIFT	8

# define DSI1_PHY_AFEC1_ACTRL_DLANE0_MASK	VC4_MASK(7, 4)

# define DSI1_PHY_AFEC1_ACTRL_DLANE0_SHIFT	4

# define DSI1_PHY_AFEC1_ACTRL_CLANE_MASK	VC4_MASK(3, 0)

# define DSI1_PHY_AFEC1_ACTRL_CLANE_SHIFT	0


#define DSI1_TST_SEL		0x78

#define DSI1_TST_MON		0x7c

#define DSI1_PHY_TST1		0x80

#define DSI1_PHY_TST2		0x84

#define DSI1_PHY_FIFO_STAT	0x88
/* Actually, all registers in the range that aren't otherwise claimed
 * will return the ID.
 */

#define DSI1_ID			0x8c

/* General DSI hardware state. */

struct vc4_dsi {
	
struct platform_device *pdev;

	
struct mipi_dsi_host dsi_host;
	
struct drm_encoder *encoder;
	
struct drm_connector *connector;
	
struct drm_panel *panel;

	
void __iomem *regs;

	
struct dma_chan *reg_dma_chan;
	
dma_addr_t reg_dma_paddr;
	
u32 *reg_dma_mem;
	
dma_addr_t reg_paddr;

	/* Whether we're on bcm2835's DSI0 or DSI1. */
	
int port;

	/* DSI channel for the panel we're connected to. */
	
u32 channel;
	
u32 lanes;
	
enum mipi_dsi_pixel_format format;
	
u32 mode_flags;

	/* Input clock from CPRMAN to the digital PHY, for the DSI
         * escape clock.
         */
	
struct clk *escape_clock;

	/* Input clock to the analog PHY, used to generate the DSI bit
         * clock.
         */
	
struct clk *pll_phy_clock;

	/* HS Clocks generated within the DSI analog PHY. */
	
struct clk_fixed_factor phy_clocks[3];

	
struct clk_hw_onecell_data *clk_onecell;

	/* Pixel clock output to the pixelvalve, generated from the HS
         * clock.
         */
	
struct clk *pixel_clock;

	
struct completion xfer_completion;
	
int xfer_result;
};


#define host_to_dsi(host) container_of(host, struct vc4_dsi, dsi_host)



static inline void

dsi_dma_workaround_write(struct vc4_dsi *dsi, u32 offset, u32 val)
{
	struct dma_chan *chan = dsi->reg_dma_chan;
	struct dma_async_tx_descriptor *tx;
	dma_cookie_t cookie;
	int ret;

	/* DSI0 should be able to write normally. */
	if (!chan) {
		writel(val, dsi->regs + offset);
		return;
	}

	*dsi->reg_dma_mem = val;

	tx = chan->device->device_prep_dma_memcpy(chan,
						  dsi->reg_paddr + offset,
						  dsi->reg_dma_paddr,
						  4, 0);
	if (!tx) {
		DRM_ERROR("Failed to set up DMA register write\n");
		return;
	}

	cookie = tx->tx_submit(tx);
	ret = dma_submit_error(cookie);
	if (ret) {
		DRM_ERROR("Failed to submit DMA: %d\n", ret);
		return;
	}
	ret = dma_sync_wait(chan, cookie);
	if (ret)
		DRM_ERROR("Failed to wait for DMA: %d\n", ret);
}


Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt153100.00%1100.00%


Total153100.00%1100.00%




#define DSI_READ(offset) readl(dsi->regs + (offset))

#define DSI_WRITE(offset, val) dsi_dma_workaround_write(dsi, offset, val)

#define DSI_PORT_READ(offset) \
	DSI_READ(dsi->port ? DSI1_##offset : DSI0_##offset)

#define DSI_PORT_WRITE(offset, val) \
	DSI_WRITE(dsi->port ? DSI1_##offset : DSI0_##offset, val)

#define DSI_PORT_BIT(bit) (dsi->port ? DSI1_##bit : DSI0_##bit)

/* VC4 DSI encoder KMS struct */

struct vc4_dsi_encoder {
	
struct vc4_encoder base;
	
struct vc4_dsi *dsi;
};



static inline struct vc4_dsi_encoder *

to_vc4_dsi_encoder(struct drm_encoder *encoder)
{
	return container_of(encoder, struct vc4_dsi_encoder, base.base);
}


Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt27100.00%1100.00%


Total27100.00%1100.00%



/* VC4 DSI connector KMS struct */

struct vc4_dsi_connector {
	
struct drm_connector base;
	
struct vc4_dsi *dsi;
};



static inline struct vc4_dsi_connector *

to_vc4_dsi_connector(struct drm_connector *connector)
{
	return container_of(connector, struct vc4_dsi_connector, base);
}


Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt25100.00%1100.00%


Total25100.00%1100.00%




#define DSI_REG(reg) { reg, #reg }
static const struct {
	
u32 reg;
	
const char *name;
} 
dsi0_regs[] = {
	DSI_REG(DSI0_CTRL),
	DSI_REG(DSI0_STAT),
	DSI_REG(DSI0_HSTX_TO_CNT),
	DSI_REG(DSI0_LPRX_TO_CNT),
	DSI_REG(DSI0_TA_TO_CNT),
	DSI_REG(DSI0_PR_TO_CNT),
	DSI_REG(DSI0_DISP0_CTRL),
	DSI_REG(DSI0_DISP1_CTRL),
	DSI_REG(DSI0_INT_STAT),
	DSI_REG(DSI0_INT_EN),
	DSI_REG(DSI0_PHYC),
	DSI_REG(DSI0_HS_CLT0),
	DSI_REG(DSI0_HS_CLT1),
	DSI_REG(DSI0_HS_CLT2),
	DSI_REG(DSI0_HS_DLT3),
	DSI_REG(DSI0_HS_DLT4),
	DSI_REG(DSI0_HS_DLT5),
	DSI_REG(DSI0_HS_DLT6),
	DSI_REG(DSI0_HS_DLT7),
	DSI_REG(DSI0_PHY_AFEC0),
	DSI_REG(DSI0_PHY_AFEC1),
	DSI_REG(DSI0_ID),
};

static const struct {
	
u32 reg;
	
const char *name;
} 
dsi1_regs[] = {
	DSI_REG(DSI1_CTRL),
	DSI_REG(DSI1_STAT),
	DSI_REG(DSI1_HSTX_TO_CNT),
	DSI_REG(DSI1_LPRX_TO_CNT),
	DSI_REG(DSI1_TA_TO_CNT),
	DSI_REG(DSI1_PR_TO_CNT),
	DSI_REG(DSI1_DISP0_CTRL),
	DSI_REG(DSI1_DISP1_CTRL),
	DSI_REG(DSI1_INT_STAT),
	DSI_REG(DSI1_INT_EN),
	DSI_REG(DSI1_PHYC),
	DSI_REG(DSI1_HS_CLT0),
	DSI_REG(DSI1_HS_CLT1),
	DSI_REG(DSI1_HS_CLT2),
	DSI_REG(DSI1_HS_DLT3),
	DSI_REG(DSI1_HS_DLT4),
	DSI_REG(DSI1_HS_DLT5),
	DSI_REG(DSI1_HS_DLT6),
	DSI_REG(DSI1_HS_DLT7),
	DSI_REG(DSI1_PHY_AFEC0),
	DSI_REG(DSI1_PHY_AFEC1),
	DSI_REG(DSI1_ID),
};




static void vc4_dsi_dump_regs(struct vc4_dsi *dsi)
{
	int i;

	if (dsi->port == 0) {
		for (i = 0; i < ARRAY_SIZE(dsi0_regs); i++) {
			DRM_INFO("0x%04x (%s): 0x%08x\n",
				 dsi0_regs[i].reg, dsi0_regs[i].name,
				 DSI_READ(dsi0_regs[i].reg));
		}
	} else {
		for (i = 0; i < ARRAY_SIZE(dsi1_regs); i++) {
			DRM_INFO("0x%04x (%s): 0x%08x\n",
				 dsi1_regs[i].reg, dsi1_regs[i].name,
				 DSI_READ(dsi1_regs[i].reg));
		}
	}
}


Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt121100.00%1100.00%


Total121100.00%1100.00%



#ifdef CONFIG_DEBUG_FS



int vc4_dsi_debugfs_regs(struct seq_file *m, void *unused)
{
	struct drm_info_node *node = (struct drm_info_node *)m->private;
	struct drm_device *drm = node->minor->dev;
	struct vc4_dev *vc4 = to_vc4_dev(drm);
	int dsi_index = (uintptr_t)node->info_ent->data;
	struct vc4_dsi *dsi = (dsi_index == 1 ? vc4->dsi1 : NULL);
	int i;

	if (!dsi)
		return 0;

	if (dsi->port == 0) {
		for (i = 0; i < ARRAY_SIZE(dsi0_regs); i++) {
			seq_printf(m, "0x%04x (%s): 0x%08x\n",
				   dsi0_regs[i].reg, dsi0_regs[i].name,
				   DSI_READ(dsi0_regs[i].reg));
		}
	} else {
		for (i = 0; i < ARRAY_SIZE(dsi1_regs); i++) {
			seq_printf(m, "0x%04x (%s): 0x%08x\n",
				   dsi1_regs[i].reg, dsi1_regs[i].name,
				   DSI_READ(dsi1_regs[i].reg));
		}
	}

	return 0;
}

Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt203100.00%1100.00%


Total203100.00%1100.00%



#endif



static enum drm_connector_status

vc4_dsi_connector_detect(struct drm_connector *connector, bool force)
{
	struct vc4_dsi_connector *vc4_connector =
		to_vc4_dsi_connector(connector);
	struct vc4_dsi *dsi = vc4_connector->dsi;

	if (dsi->panel)
		return connector_status_connected;
	else
		return connector_status_disconnected;
}


Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt47100.00%1100.00%


Total47100.00%1100.00%






static void vc4_dsi_connector_destroy(struct drm_connector *connector)
{
	drm_connector_unregister(connector);
	drm_connector_cleanup(connector);
}


Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt21100.00%1100.00%


Total21100.00%1100.00%






static int vc4_dsi_connector_get_modes(struct drm_connector *connector)
{
	struct vc4_dsi_connector *vc4_connector =
		to_vc4_dsi_connector(connector);
	struct vc4_dsi *dsi = vc4_connector->dsi;

	if (dsi->panel)
		return drm_panel_get_modes(dsi->panel);

	return 0;
}


Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt47100.00%1100.00%


Total47100.00%1100.00%




static const struct drm_connector_funcs vc4_dsi_connector_funcs = {
	.dpms = drm_atomic_helper_connector_dpms,
	.detect = vc4_dsi_connector_detect,
	.fill_modes = drm_helper_probe_single_connector_modes,
	.destroy = vc4_dsi_connector_destroy,
	.reset = drm_atomic_helper_connector_reset,
	.atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
	.atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
};


static const struct drm_connector_helper_funcs vc4_dsi_connector_helper_funcs = {
	.get_modes = vc4_dsi_connector_get_modes,
};




static struct drm_connector *vc4_dsi_connector_init(struct drm_device *dev,
						    struct vc4_dsi *dsi)
{
	struct drm_connector *connector = NULL;
	struct vc4_dsi_connector *dsi_connector;
	int ret = 0;

	dsi_connector = devm_kzalloc(dev->dev, sizeof(*dsi_connector),
				     GFP_KERNEL);
	if (!dsi_connector) {
		ret = -ENOMEM;
		goto fail;
	}
	connector = &dsi_connector->base;

	dsi_connector->dsi = dsi;

	drm_connector_init(dev, connector, &vc4_dsi_connector_funcs,
			   DRM_MODE_CONNECTOR_DSI);
	drm_connector_helper_add(connector, &vc4_dsi_connector_helper_funcs);

	connector->polled = 0;
	connector->interlace_allowed = 0;
	connector->doublescan_allowed = 0;

	drm_mode_connector_attach_encoder(connector, dsi->encoder);

	return connector;

fail:
	if (connector)
		vc4_dsi_connector_destroy(connector);

	return ERR_PTR(ret);
}


Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt147100.00%1100.00%


Total147100.00%1100.00%






static void vc4_dsi_encoder_destroy(struct drm_encoder *encoder)
{
	drm_encoder_cleanup(encoder);
}


Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt16100.00%1100.00%


Total16100.00%1100.00%




static const struct drm_encoder_funcs vc4_dsi_encoder_funcs = {
	.destroy = vc4_dsi_encoder_destroy,
};




static void vc4_dsi_latch_ulps(struct vc4_dsi *dsi, bool latch)
{
	u32 afec0 = DSI_PORT_READ(PHY_AFEC0);

	if (latch)
		afec0 |= DSI_PORT_BIT(PHY_AFEC0_LATCH_ULPS);
	else
		afec0 &= ~DSI_PORT_BIT(PHY_AFEC0_LATCH_ULPS);

	DSI_PORT_WRITE(PHY_AFEC0, afec0);
}


Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt49100.00%1100.00%


Total49100.00%1100.00%



/* Enters or exits Ultra Low Power State. */



static void vc4_dsi_ulps(struct vc4_dsi *dsi, bool ulps)
{
	bool continuous = dsi->mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS;
	u32 phyc_ulps = ((continuous ? DSI_PORT_BIT(PHYC_CLANE_ULPS) : 0) |
			 DSI_PHYC_DLANE0_ULPS |
			 (dsi->lanes > 1 ? DSI_PHYC_DLANE1_ULPS : 0) |
			 (dsi->lanes > 2 ? DSI_PHYC_DLANE2_ULPS : 0) |
			 (dsi->lanes > 3 ? DSI_PHYC_DLANE3_ULPS : 0));
	u32 stat_ulps = ((continuous ? DSI1_STAT_PHY_CLOCK_ULPS : 0) |
			 DSI1_STAT_PHY_D0_ULPS |
			 (dsi->lanes > 1 ? DSI1_STAT_PHY_D1_ULPS : 0) |
			 (dsi->lanes > 2 ? DSI1_STAT_PHY_D2_ULPS : 0) |
			 (dsi->lanes > 3 ? DSI1_STAT_PHY_D3_ULPS : 0));
	u32 stat_stop = ((continuous ? DSI1_STAT_PHY_CLOCK_STOP : 0) |
			 DSI1_STAT_PHY_D0_STOP |
			 (dsi->lanes > 1 ? DSI1_STAT_PHY_D1_STOP : 0) |
			 (dsi->lanes > 2 ? DSI1_STAT_PHY_D2_STOP : 0) |
			 (dsi->lanes > 3 ? DSI1_STAT_PHY_D3_STOP : 0));
	int ret;

	DSI_PORT_WRITE(STAT, stat_ulps);
	DSI_PORT_WRITE(PHYC, DSI_PORT_READ(PHYC) | phyc_ulps);
	ret = wait_for((DSI_PORT_READ(STAT) & stat_ulps) == stat_ulps, 200);
	if (ret) {
		dev_warn(&dsi->pdev->dev,
			 "Timeout waiting for DSI ULPS entry: STAT 0x%08x",
			 DSI_PORT_READ(STAT));
		DSI_PORT_WRITE(PHYC, DSI_PORT_READ(PHYC) & ~phyc_ulps);
		vc4_dsi_latch_ulps(dsi, false);
		return;
	}

	/* The DSI module can't be disabled while the module is
         * generating ULPS state.  So, to be able to disable the
         * module, we have the AFE latch the ULPS state and continue
         * on to having the module enter STOP.
         */
	vc4_dsi_latch_ulps(dsi, ulps);

	DSI_PORT_WRITE(STAT, stat_stop);
	DSI_PORT_WRITE(PHYC, DSI_PORT_READ(PHYC) & ~phyc_ulps);
	ret = wait_for((DSI_PORT_READ(STAT) & stat_stop) == stat_stop, 200);
	if (ret) {
		dev_warn(&dsi->pdev->dev,
			 "Timeout waiting for DSI STOP entry: STAT 0x%08x",
			 DSI_PORT_READ(STAT));
		DSI_PORT_WRITE(PHYC, DSI_PORT_READ(PHYC) & ~phyc_ulps);
		return;
	}
}


Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt346100.00%1100.00%


Total346100.00%1100.00%





static u32

dsi_hs_timing(u32 ui_ns, u32 ns, u32 ui)
{
	/* The HS timings have to be rounded up to a multiple of 8
         * because we're using the byte clock.
         */
	return roundup(ui + DIV_ROUND_UP(ns, ui_ns), 8);
}


Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt31100.00%1100.00%


Total31100.00%1100.00%



/* ESC always runs at 100Mhz. */

#define ESC_TIME_NS 10



static u32

dsi_esc_timing(u32 ns)
{
	return DIV_ROUND_UP(ns, ESC_TIME_NS);
}


Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt17100.00%1100.00%


Total17100.00%1100.00%






static void vc4_dsi_encoder_disable(struct drm_encoder *encoder)
{
	struct vc4_dsi_encoder *vc4_encoder = to_vc4_dsi_encoder(encoder);
	struct vc4_dsi *dsi = vc4_encoder->dsi;
	struct device *dev = &dsi->pdev->dev;

	drm_panel_disable(dsi->panel);

	vc4_dsi_ulps(dsi, true);

	drm_panel_unprepare(dsi->panel);

	clk_disable_unprepare(dsi->pll_phy_clock);
	clk_disable_unprepare(dsi->escape_clock);
	clk_disable_unprepare(dsi->pixel_clock);

	pm_runtime_put(dev);
}


Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt89100.00%1100.00%


Total89100.00%1100.00%






static void vc4_dsi_encoder_enable(struct drm_encoder *encoder)
{
	struct drm_display_mode *mode = &encoder->crtc->mode;
	struct vc4_dsi_encoder *vc4_encoder = to_vc4_dsi_encoder(encoder);
	struct vc4_dsi *dsi = vc4_encoder->dsi;
	struct device *dev = &dsi->pdev->dev;
	u32 format = 0, divider = 0;
	bool debug_dump_regs = false;
	unsigned long hs_clock;
	u32 ui_ns;
	/* Minimum LP state duration in escape clock cycles. */
	u32 lpx = dsi_esc_timing(60);
	unsigned long pixel_clock_hz = mode->clock * 1000;
	unsigned long dsip_clock;
	unsigned long phy_clock;
	int ret;

	ret = pm_runtime_get_sync(dev);
	if (ret) {
		DRM_ERROR("Failed to runtime PM enable on DSI%d\n", dsi->port);
		return;
	}

	ret = drm_panel_prepare(dsi->panel);
	if (ret) {
		DRM_ERROR("Panel failed to prepare\n");
		return;
	}

	if (debug_dump_regs) {
		DRM_INFO("DSI regs before:\n");
		vc4_dsi_dump_regs(dsi);
	}

	switch (dsi->format) {
	case MIPI_DSI_FMT_RGB888:
		format = DSI_PFORMAT_RGB888;
		divider = 24 / dsi->lanes;
		break;
	case MIPI_DSI_FMT_RGB666:
		format = DSI_PFORMAT_RGB666;
		divider = 24 / dsi->lanes;
		break;
	case MIPI_DSI_FMT_RGB666_PACKED:
		format = DSI_PFORMAT_RGB666_PACKED;
		divider = 18 / dsi->lanes;
		break;
	case MIPI_DSI_FMT_RGB565:
		format = DSI_PFORMAT_RGB565;
		divider = 16 / dsi->lanes;
		break;
	}

	phy_clock = pixel_clock_hz * divider;
	ret = clk_set_rate(dsi->pll_phy_clock, phy_clock);
	if (ret) {
		dev_err(&dsi->pdev->dev,
			"Failed to set phy clock to %ld: %d\n", phy_clock, ret);
	}

	/* Reset the DSI and all its fifos. */
	DSI_PORT_WRITE(CTRL,
		       DSI_CTRL_SOFT_RESET_CFG |
		       DSI_PORT_BIT(CTRL_RESET_FIFOS));

	DSI_PORT_WRITE(CTRL,
		       DSI_CTRL_HSDT_EOT_DISABLE |
		       DSI_CTRL_RX_LPDT_EOT_DISABLE);

	/* Clear all stat bits so we see what has happened during enable. */
	DSI_PORT_WRITE(STAT, DSI_PORT_READ(STAT));

	/* Set AFE CTR00/CTR1 to release powerdown of analog. */
	if (dsi->port == 0) {
		u32 afec0 = (VC4_SET_FIELD(7, DSI_PHY_AFEC0_PTATADJ) |
			     VC4_SET_FIELD(7, DSI_PHY_AFEC0_CTATADJ));

		if (dsi->lanes < 2)
			afec0 |= DSI0_PHY_AFEC0_PD_DLANE1;

		if (!(dsi->mode_flags & MIPI_DSI_MODE_VIDEO))
			afec0 |= DSI0_PHY_AFEC0_RESET;

		DSI_PORT_WRITE(PHY_AFEC0, afec0);

		DSI_PORT_WRITE(PHY_AFEC1,
			       VC4_SET_FIELD(6,  DSI0_PHY_AFEC1_IDR_DLANE1) |
			       VC4_SET_FIELD(6,  DSI0_PHY_AFEC1_IDR_DLANE0) |
			       VC4_SET_FIELD(6,  DSI0_PHY_AFEC1_IDR_CLANE));
	} else {
		u32 afec0 = (VC4_SET_FIELD(7, DSI_PHY_AFEC0_PTATADJ) |
			     VC4_SET_FIELD(7, DSI_PHY_AFEC0_CTATADJ) |
			     VC4_SET_FIELD(6, DSI1_PHY_AFEC0_IDR_CLANE) |
			     VC4_SET_FIELD(6, DSI1_PHY_AFEC0_IDR_DLANE0) |
			     VC4_SET_FIELD(6, DSI1_PHY_AFEC0_IDR_DLANE1) |
			     VC4_SET_FIELD(6, DSI1_PHY_AFEC0_IDR_DLANE2) |
			     VC4_SET_FIELD(6, DSI1_PHY_AFEC0_IDR_DLANE3));

		if (dsi->lanes < 4)
			afec0 |= DSI1_PHY_AFEC0_PD_DLANE3;
		if (dsi->lanes < 3)
			afec0 |= DSI1_PHY_AFEC0_PD_DLANE2;
		if (dsi->lanes < 2)
			afec0 |= DSI1_PHY_AFEC0_PD_DLANE1;

		afec0 |= DSI1_PHY_AFEC0_RESET;

		DSI_PORT_WRITE(PHY_AFEC0, afec0);

		DSI_PORT_WRITE(PHY_AFEC1, 0);

		/* AFEC reset hold time */
		mdelay(1);
	}

	ret = clk_prepare_enable(dsi->escape_clock);
	if (ret) {
		DRM_ERROR("Failed to turn on DSI escape clock: %d\n", ret);
		return;
	}

	ret = clk_prepare_enable(dsi->pll_phy_clock);
	if (ret) {
		DRM_ERROR("Failed to turn on DSI PLL: %d\n", ret);
		return;
	}

	hs_clock = clk_get_rate(dsi->pll_phy_clock);

	/* Yes, we set the DSI0P/DSI1P pixel clock to the byte rate,
         * not the pixel clock rate.  DSIxP take from the APHY's byte,
         * DDR2, or DDR4 clock (we use byte) and feed into the PV at
         * that rate.  Separately, a value derived from PIX_CLK_DIV
         * and HS_CLKC is fed into the PV to divide down to the actual
         * pixel clock for pushing pixels into DSI.
         */
	dsip_clock = phy_clock / 8;
	ret = clk_set_rate(dsi->pixel_clock, dsip_clock);
	if (ret) {
		dev_err(dev, "Failed to set pixel clock to %ldHz: %d\n",
			dsip_clock, ret);
	}

	ret = clk_prepare_enable(dsi->pixel_clock);
	if (ret) {
		DRM_ERROR("Failed to turn on DSI pixel clock: %d\n", ret);
		return;
	}

	/* How many ns one DSI unit interval is.  Note that the clock
         * is DDR, so there's an extra divide by 2.
         */
	ui_ns = DIV_ROUND_UP(500000000, hs_clock);

	DSI_PORT_WRITE(HS_CLT0,
		       VC4_SET_FIELD(dsi_hs_timing(ui_ns, 262, 0),
				     DSI_HS_CLT0_CZERO) |
		       VC4_SET_FIELD(dsi_hs_timing(ui_ns, 0, 8),
				     DSI_HS_CLT0_CPRE) |
		       VC4_SET_FIELD(dsi_hs_timing(ui_ns, 38, 0),
				     DSI_HS_CLT0_CPREP));

	DSI_PORT_WRITE(HS_CLT1,
		       VC4_SET_FIELD(dsi_hs_timing(ui_ns, 60, 0),
				     DSI_HS_CLT1_CTRAIL) |
		       VC4_SET_FIELD(dsi_hs_timing(ui_ns, 60, 52),
				     DSI_HS_CLT1_CPOST));

	DSI_PORT_WRITE(HS_CLT2,
		       VC4_SET_FIELD(dsi_hs_timing(ui_ns, 1000000, 0),
				     DSI_HS_CLT2_WUP));

	DSI_PORT_WRITE(HS_DLT3,
		       VC4_SET_FIELD(dsi_hs_timing(ui_ns, 100, 0),
				     DSI_HS_DLT3_EXIT) |
		       VC4_SET_FIELD(dsi_hs_timing(ui_ns, 105, 6),
				     DSI_HS_DLT3_ZERO) |
		       VC4_SET_FIELD(dsi_hs_timing(ui_ns, 40, 4),
				     DSI_HS_DLT3_PRE));

	DSI_PORT_WRITE(HS_DLT4,
		       VC4_SET_FIELD(dsi_hs_timing(ui_ns, lpx * ESC_TIME_NS, 0),
				     DSI_HS_DLT4_LPX) |
		       VC4_SET_FIELD(max(dsi_hs_timing(ui_ns, 0, 8),
					 dsi_hs_timing(ui_ns, 60, 4)),
				     DSI_HS_DLT4_TRAIL) |
		       VC4_SET_FIELD(0, DSI_HS_DLT4_ANLAT));

	DSI_PORT_WRITE(HS_DLT5, VC4_SET_FIELD(dsi_hs_timing(ui_ns, 1000, 5000),
					      DSI_HS_DLT5_INIT));

	DSI_PORT_WRITE(HS_DLT6,
		       VC4_SET_FIELD(lpx * 5, DSI_HS_DLT6_TA_GET) |
		       VC4_SET_FIELD(lpx, DSI_HS_DLT6_TA_SURE) |
		       VC4_SET_FIELD(lpx * 4, DSI_HS_DLT6_TA_GO) |
		       VC4_SET_FIELD(lpx, DSI_HS_DLT6_LP_LPX));

	DSI_PORT_WRITE(HS_DLT7,
		       VC4_SET_FIELD(dsi_esc_timing(1000000),
				     DSI_HS_DLT7_LP_WUP));

	DSI_PORT_WRITE(PHYC,
		       DSI_PHYC_DLANE0_ENABLE |
		       (dsi->lanes >= 2 ? DSI_PHYC_DLANE1_ENABLE : 0) |
		       (dsi->lanes >= 3 ? DSI_PHYC_DLANE2_ENABLE : 0) |
		       (dsi->lanes >= 4 ? DSI_PHYC_DLANE3_ENABLE : 0) |
		       DSI_PORT_BIT(PHYC_CLANE_ENABLE) |
		       ((dsi->mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS) ?
			0 : DSI_PORT_BIT(PHYC_HS_CLK_CONTINUOUS)) |
		       (dsi->port == 0 ?
			VC4_SET_FIELD(lpx - 1, DSI0_PHYC_ESC_CLK_LPDT) :
			VC4_SET_FIELD(lpx - 1, DSI1_PHYC_ESC_CLK_LPDT)));

	DSI_PORT_WRITE(CTRL,
		       DSI_PORT_READ(CTRL) |
		       DSI_CTRL_CAL_BYTE);

	/* HS timeout in HS clock cycles: disabled. */
	DSI_PORT_WRITE(HSTX_TO_CNT, 0);
	/* LP receive timeout in HS clocks. */
	DSI_PORT_WRITE(LPRX_TO_CNT, 0xffffff);
	/* Bus turnaround timeout */
	DSI_PORT_WRITE(TA_TO_CNT, 100000);
	/* Display reset sequence timeout */
	DSI_PORT_WRITE(PR_TO_CNT, 100000);

	if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO) {
		DSI_PORT_WRITE(DISP0_CTRL,
			       VC4_SET_FIELD(divider, DSI_DISP0_PIX_CLK_DIV) |
			       VC4_SET_FIELD(format, DSI_DISP0_PFORMAT) |
			       VC4_SET_FIELD(DSI_DISP0_LP_STOP_PERFRAME,
					     DSI_DISP0_LP_STOP_CTRL) |
			       DSI_DISP0_ST_END |
			       DSI_DISP0_ENABLE);
	} else {
		DSI_PORT_WRITE(DISP0_CTRL,
			       DSI_DISP0_COMMAND_MODE |
			       DSI_DISP0_ENABLE);
	}

	/* Set up DISP1 for transferring long command payloads through
         * the pixfifo.
         */
	DSI_PORT_WRITE(DISP1_CTRL,
		       VC4_SET_FIELD(DSI_DISP1_PFORMAT_32BIT_LE,
				     DSI_DISP1_PFORMAT) |
		       DSI_DISP1_ENABLE);

	/* Ungate the block. */
	if (dsi->port == 0)
		DSI_PORT_WRITE(CTRL, DSI_PORT_READ(CTRL) | DSI0_CTRL_CTRL0);
	else
		DSI_PORT_WRITE(CTRL, DSI_PORT_READ(CTRL) | DSI1_CTRL_EN);

	/* Bring AFE out of reset. */
	if (dsi->port == 0) {
        } else {
		DSI_PORT_WRITE(PHY_AFEC0,
			       DSI_PORT_READ(PHY_AFEC0) &
			       ~DSI1_PHY_AFEC0_RESET);
	}

	vc4_dsi_ulps(dsi, false);

	if (debug_dump_regs) {
		DRM_INFO("DSI regs after:\n");
		vc4_dsi_dump_regs(dsi);
	}

	ret = drm_panel_enable(dsi->panel);
	if (ret) {
		DRM_ERROR("Panel failed to enable\n");
		drm_panel_unprepare(dsi->panel);
		return;
	}
}


Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt1223100.00%1100.00%


Total1223100.00%1100.00%






static ssize_t vc4_dsi_host_transfer(struct mipi_dsi_host *host,
				     const struct mipi_dsi_msg *msg)
{
	struct vc4_dsi *dsi = host_to_dsi(host);
	struct mipi_dsi_packet packet;
	u32 pkth = 0, pktc = 0;
	int i, ret;
	bool is_long = mipi_dsi_packet_format_is_long(msg->type);
	u32 cmd_fifo_len = 0, pix_fifo_len = 0;

	mipi_dsi_create_packet(&packet, msg);

	pkth |= VC4_SET_FIELD(packet.header[0], DSI_TXPKT1H_BC_DT);
	pkth |= VC4_SET_FIELD(packet.header[1] |
			      (packet.header[2] << 8),
			      DSI_TXPKT1H_BC_PARAM);
	if (is_long) {
		/* Divide data across the various FIFOs we have available.
                 * The command FIFO takes byte-oriented data, but is of
                 * limited size. The pixel FIFO (never actually used for
                 * pixel data in reality) is word oriented, and substantially
                 * larger. So, we use the pixel FIFO for most of the data,
                 * sending the residual bytes in the command FIFO at the start.
                 *
                 * With this arrangement, the command FIFO will never get full.
                 */
		if (packet.payload_length <= 16) {
			cmd_fifo_len = packet.payload_length;
			pix_fifo_len = 0;
		} else {
			cmd_fifo_len = (packet.payload_length %
					DSI_PIX_FIFO_WIDTH);
			pix_fifo_len = ((packet.payload_length - cmd_fifo_len) /
					DSI_PIX_FIFO_WIDTH);
		}

		WARN_ON_ONCE(pix_fifo_len >= DSI_PIX_FIFO_DEPTH);

		pkth |= VC4_SET_FIELD(cmd_fifo_len, DSI_TXPKT1H_BC_CMDFIFO);
	}

	if (msg->rx_len) {
		pktc |= VC4_SET_FIELD(DSI_TXPKT1C_CMD_CTRL_RX,
				      DSI_TXPKT1C_CMD_CTRL);
	} else {
		pktc |= VC4_SET_FIELD(DSI_TXPKT1C_CMD_CTRL_TX,
				      DSI_TXPKT1C_CMD_CTRL);
	}

	for (i = 0; i < cmd_fifo_len; i++)
		DSI_PORT_WRITE(TXPKT_CMD_FIFO, packet.payload[i]);
	for (i = 0; i < pix_fifo_len; i++) {
		const u8 *pix = packet.payload + cmd_fifo_len + i * 4;

		DSI_PORT_WRITE(TXPKT_PIX_FIFO,
			       pix[0] |
			       pix[1] << 8 |
			       pix[2] << 16 |
			       pix[3] << 24);
	}

	if (msg->flags & MIPI_DSI_MSG_USE_LPM)
		pktc |= DSI_TXPKT1C_CMD_MODE_LP;
	if (is_long)
		pktc |= DSI_TXPKT1C_CMD_TYPE_LONG;

	/* Send one copy of the packet.  Larger repeats are used for pixel
         * data in command mode.
         */
	pktc |= VC4_SET_FIELD(1, DSI_TXPKT1C_CMD_REPEAT);

	pktc |= DSI_TXPKT1C_CMD_EN;
	if (pix_fifo_len) {
		pktc |= VC4_SET_FIELD(DSI_TXPKT1C_DISPLAY_NO_SECONDARY,
				      DSI_TXPKT1C_DISPLAY_NO);
	} else {
		pktc |= VC4_SET_FIELD(DSI_TXPKT1C_DISPLAY_NO_SHORT,
				      DSI_TXPKT1C_DISPLAY_NO);
	}

	/* Enable the appropriate interrupt for the transfer completion. */
	dsi->xfer_result = 0;
	reinit_completion(&dsi->xfer_completion);
	DSI_PORT_WRITE(INT_STAT, DSI1_INT_TXPKT1_DONE | DSI1_INT_PHY_DIR_RTF);
	if (msg->rx_len) {
		DSI_PORT_WRITE(INT_EN, (DSI1_INTERRUPTS_ALWAYS_ENABLED |
					DSI1_INT_PHY_DIR_RTF));
	} else {
		DSI_PORT_WRITE(INT_EN, (DSI1_INTERRUPTS_ALWAYS_ENABLED |
					DSI1_INT_TXPKT1_DONE));
	}

	/* Send the packet. */
	DSI_PORT_WRITE(TXPKT1H, pkth);
	DSI_PORT_WRITE(TXPKT1C, pktc);

	if (!wait_for_completion_timeout(&dsi->xfer_completion,
					 msecs_to_jiffies(1000))) {
		dev_err(&dsi->pdev->dev, "transfer interrupt wait timeout");
		dev_err(&dsi->pdev->dev, "instat: 0x%08x\n",
			DSI_PORT_READ(INT_STAT));
		ret = -ETIMEDOUT;
	} else {
		ret = dsi->xfer_result;
	}

	DSI_PORT_WRITE(INT_EN, DSI1_INTERRUPTS_ALWAYS_ENABLED);

	if (ret)
		goto reset_fifo_and_return;

	if (ret == 0 && msg->rx_len) {
		u32 rxpkt1h = DSI_PORT_READ(RXPKT1H);
		u8 *msg_rx = msg->rx_buf;

		if (rxpkt1h & DSI_RXPKT1H_PKT_TYPE_LONG) {
			u32 rxlen = VC4_GET_FIELD(rxpkt1h,
						  DSI_RXPKT1H_BC_PARAM);

			if (rxlen != msg->rx_len) {
				DRM_ERROR("DSI returned %db, expecting %db\n",
					  rxlen, (int)msg->rx_len);
				ret = -ENXIO;
				goto reset_fifo_and_return;
			}

			for (i = 0; i < msg->rx_len; i++)
				msg_rx[i] = DSI_READ(DSI1_RXPKT_FIFO);
		} else {
			/* FINISHME: Handle AWER */

			msg_rx[0] = VC4_GET_FIELD(rxpkt1h,
						  DSI_RXPKT1H_SHORT_0);
			if (msg->rx_len > 1) {
				msg_rx[1] = VC4_GET_FIELD(rxpkt1h,
							  DSI_RXPKT1H_SHORT_1);
			}
		}
	}

	return ret;

reset_fifo_and_return:
	DRM_ERROR("DSI transfer failed, resetting: %d\n", ret);

	DSI_PORT_WRITE(TXPKT1C, DSI_PORT_READ(TXPKT1C) & ~DSI_TXPKT1C_CMD_EN);
	udelay(1);
	DSI_PORT_WRITE(CTRL,
		       DSI_PORT_READ(CTRL) |
		       DSI_PORT_BIT(CTRL_RESET_FIFOS));

	DSI_PORT_WRITE(TXPKT1C, 0);
	DSI_PORT_WRITE(INT_EN, DSI1_INTERRUPTS_ALWAYS_ENABLED);
	return ret;
}


Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt707100.00%1100.00%


Total707100.00%1100.00%






static int vc4_dsi_host_attach(struct mipi_dsi_host *host,
			       struct mipi_dsi_device *device)
{
	struct vc4_dsi *dsi = host_to_dsi(host);
	int ret = 0;

	dsi->lanes = device->lanes;
	dsi->channel = device->channel;
	dsi->format = device->format;
	dsi->mode_flags = device->mode_flags;

	if (!(dsi->mode_flags & MIPI_DSI_MODE_VIDEO)) {
		dev_err(&dsi->pdev->dev,
			"Only VIDEO mode panels supported currently.\n");
		return 0;
	}

	dsi->panel = of_drm_find_panel(device->dev.of_node);
	if (!dsi->panel)
		return 0;

	ret = drm_panel_attach(dsi->panel, dsi->connector);
	if (ret != 0)
		return ret;

	drm_helper_hpd_irq_event(dsi->connector->dev);

	return 0;
}


Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt148100.00%1100.00%


Total148100.00%1100.00%






static int vc4_dsi_host_detach(struct mipi_dsi_host *host,
			       struct mipi_dsi_device *device)
{
	struct vc4_dsi *dsi = host_to_dsi(host);

	if (dsi->panel) {
		int ret = drm_panel_detach(dsi->panel);

		if (ret)
			return ret;

		dsi->panel = NULL;

		drm_helper_hpd_irq_event(dsi->connector->dev);
	}

	return 0;
}


Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt69100.00%1100.00%


Total69100.00%1100.00%




static const struct mipi_dsi_host_ops vc4_dsi_host_ops = {
	.attach = vc4_dsi_host_attach,
	.detach = vc4_dsi_host_detach,
	.transfer = vc4_dsi_host_transfer,
};


static const struct drm_encoder_helper_funcs vc4_dsi_encoder_helper_funcs = {
	.disable = vc4_dsi_encoder_disable,
	.enable = vc4_dsi_encoder_enable,
};


static const struct of_device_id vc4_dsi_dt_match[] = {
	{ .compatible = "brcm,bcm2835-dsi1", (void *)(uintptr_t)1 },
	{}
};




static void dsi_handle_error(struct vc4_dsi *dsi,
			     irqreturn_t *ret, u32 stat, u32 bit,
			     const char *type)
{
	if (!(stat & bit))
		return;

	DRM_ERROR("DSI%d: %s error\n", dsi->port, type);
	*ret = IRQ_HANDLED;
}


Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt52100.00%1100.00%


Total52100.00%1100.00%






static irqreturn_t vc4_dsi_irq_handler(int irq, void *data)
{
	struct vc4_dsi *dsi = data;
	u32 stat = DSI_PORT_READ(INT_STAT);
	irqreturn_t ret = IRQ_NONE;

	DSI_PORT_WRITE(INT_STAT, stat);

	dsi_handle_error(dsi, &ret, stat,
			 DSI1_INT_ERR_SYNC_ESC, "LPDT sync");
	dsi_handle_error(dsi, &ret, stat,
			 DSI1_INT_ERR_CONTROL, "data lane 0 sequence");
	dsi_handle_error(dsi, &ret, stat,
			 DSI1_INT_ERR_CONT_LP0, "LP0 contention");
	dsi_handle_error(dsi, &ret, stat,
			 DSI1_INT_ERR_CONT_LP1, "LP1 contention");
	dsi_handle_error(dsi, &ret, stat,
			 DSI1_INT_HSTX_TO, "HSTX timeout");
	dsi_handle_error(dsi, &ret, stat,
			 DSI1_INT_LPRX_TO, "LPRX timeout");
	dsi_handle_error(dsi, &ret, stat,
			 DSI1_INT_TA_TO, "turnaround timeout");
	dsi_handle_error(dsi, &ret, stat,
			 DSI1_INT_PR_TO, "peripheral reset timeout");

	if (stat & (DSI1_INT_TXPKT1_DONE | DSI1_INT_PHY_DIR_RTF)) {
		complete(&dsi->xfer_completion);
		ret = IRQ_HANDLED;
	} else if (stat & DSI1_INT_HSTX_TO) {
		complete(&dsi->xfer_completion);
		dsi->xfer_result = -ETIMEDOUT;
		ret = IRQ_HANDLED;
	}

	return ret;
}


Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt207100.00%1100.00%


Total207100.00%1100.00%



/**
 * Exposes clocks generated by the analog PHY that are consumed by
 * CPRMAN (clk-bcm2835.c).
 */


static int

vc4_dsi_init_phy_clocks(struct vc4_dsi *dsi)
{
	struct device *dev = &dsi->pdev->dev;
	const char *parent_name = __clk_get_name(dsi->pll_phy_clock);
	static const struct {
		const char *dsi0_name, *dsi1_name;
		int div;
	} phy_clocks[] = {
		{ "dsi0_byte", "dsi1_byte", 8 },
		{ "dsi0_ddr2", "dsi1_ddr2", 4 },
		{ "dsi0_ddr", "dsi1_ddr", 2 },
        };
	int i;

	dsi->clk_onecell = devm_kzalloc(dev,
					sizeof(*dsi->clk_onecell) +
					ARRAY_SIZE(phy_clocks) *
					sizeof(struct clk_hw *),
					GFP_KERNEL);
	if (!dsi->clk_onecell)
		return -ENOMEM;
	dsi->clk_onecell->num = ARRAY_SIZE(phy_clocks);

	for (i = 0; i < ARRAY_SIZE(phy_clocks); i++) {
		struct clk_fixed_factor *fix = &dsi->phy_clocks[i];
		struct clk_init_data init;
		int ret;

		/* We just use core fixed factor clock ops for the PHY
                 * clocks.  The clocks are actually gated by the
                 * PHY_AFEC0_DDRCLK_EN bits, which we should be
                 * setting if we use the DDR/DDR2 clocks.  However,
                 * vc4_dsi_encoder_enable() is setting up both AFEC0,
                 * setting both our parent DSI PLL's rate and this
                 * clock's rate, so it knows if DDR/DDR2 are going to
                 * be used and could enable the gates itself.
                 */
		fix->mult = 1;
		fix->div = phy_clocks[i].div;
		fix->hw.init = &init;

		memset(&init, 0, sizeof(init));
		init.parent_names = &parent_name;
		init.num_parents = 1;
		if (dsi->port == 1)
			init.name = phy_clocks[i].dsi1_name;
		else
			init.name = phy_clocks[i].dsi0_name;
		init.ops = &clk_fixed_factor_ops;

		ret = devm_clk_hw_register(dev, &fix->hw);
		if (ret)
			return ret;

		dsi->clk_onecell->hws[i] = &fix->hw;
	}

	return of_clk_add_hw_provider(dev->of_node,
				      of_clk_hw_onecell_get,
				      dsi->clk_onecell);
}


Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt312100.00%1100.00%


Total312100.00%1100.00%






static int vc4_dsi_bind(struct device *dev, struct device *master, void *data)
{
	struct platform_device *pdev = to_platform_device(dev);
	struct drm_device *drm = dev_get_drvdata(master);
	struct vc4_dev *vc4 = to_vc4_dev(drm);
	struct vc4_dsi *dsi;
	struct vc4_dsi_encoder *vc4_dsi_encoder;
	const struct of_device_id *match;
	dma_cap_mask_t dma_mask;
	int ret;

	dsi = devm_kzalloc(dev, sizeof(*dsi), GFP_KERNEL);
	if (!dsi)
		return -ENOMEM;

	match = of_match_device(vc4_dsi_dt_match, dev);
	if (!match)
		return -ENODEV;

	dsi->port = (uintptr_t)match->data;

	vc4_dsi_encoder = devm_kzalloc(dev, sizeof(*vc4_dsi_encoder),
				       GFP_KERNEL);
	if (!vc4_dsi_encoder)
		return -ENOMEM;
	vc4_dsi_encoder->base.type = VC4_ENCODER_TYPE_DSI1;
	vc4_dsi_encoder->dsi = dsi;
	dsi->encoder = &vc4_dsi_encoder->base.base;

	dsi->pdev = pdev;
	dsi->regs = vc4_ioremap_regs(pdev, 0);
	if (IS_ERR(dsi->regs))
		return PTR_ERR(dsi->regs);

	if (DSI_PORT_READ(ID) != DSI_ID_VALUE) {
		dev_err(dev, "Port returned 0x%08x for ID instead of 0x%08x\n",
			DSI_PORT_READ(ID), DSI_ID_VALUE);
		return -ENODEV;
	}

	/* DSI1 has a broken AXI slave that doesn't respond to writes
         * from the ARM.  It does handle writes from the DMA engine,
         * so set up a channel for talking to it.
         */
	if (dsi->port == 1) {
		dsi->reg_dma_mem = dma_alloc_coherent(dev, 4,
						      &dsi->reg_dma_paddr,
						      GFP_KERNEL);
		if (!dsi->reg_dma_mem) {
			DRM_ERROR("Failed to get DMA memory\n");
			return -ENOMEM;
		}

		dma_cap_zero(dma_mask);
		dma_cap_set(DMA_MEMCPY, dma_mask);
		dsi->reg_dma_chan = dma_request_chan_by_mask(&dma_mask);
		if (IS_ERR(dsi->reg_dma_chan)) {
			ret = PTR_ERR(dsi->reg_dma_chan);
			if (ret != -EPROBE_DEFER)
				DRM_ERROR("Failed to get DMA channel: %d\n",
					  ret);
			return ret;
		}

		/* Get the physical address of the device's registers.  The
                 * struct resource for the regs gives us the bus address
                 * instead.
                 */
		dsi->reg_paddr = be32_to_cpup(of_get_address(dev->of_node,
							     0, NULL, NULL));
	}

	init_completion(&dsi->xfer_completion);
	/* At startup enable error-reporting interrupts and nothing else. */
	DSI_PORT_WRITE(INT_EN, DSI1_INTERRUPTS_ALWAYS_ENABLED);
	/* Clear any existing interrupt state. */
	DSI_PORT_WRITE(INT_STAT, DSI_PORT_READ(INT_STAT));

	ret = devm_request_irq(dev, platform_get_irq(pdev, 0),
			       vc4_dsi_irq_handler, 0, "vc4 dsi", dsi);
	if (ret) {
		if (ret != -EPROBE_DEFER)
			dev_err(dev, "Failed to get interrupt: %d\n", ret);
		return ret;
	}

	dsi->escape_clock = devm_clk_get(dev, "escape");
	if (IS_ERR(dsi->escape_clock)) {
		ret = PTR_ERR(dsi->escape_clock);
		if (ret != -EPROBE_DEFER)
			dev_err(dev, "Failed to get escape clock: %d\n", ret);
		return ret;
	}

	dsi->pll_phy_clock = devm_clk_get(dev, "phy");
	if (IS_ERR(dsi->pll_phy_clock)) {
		ret = PTR_ERR(dsi->pll_phy_clock);
		if (ret != -EPROBE_DEFER)
			dev_err(dev, "Failed to get phy clock: %d\n", ret);
		return ret;
	}

	dsi->pixel_clock = devm_clk_get(dev, "pixel");
	if (IS_ERR(dsi->pixel_clock)) {
		ret = PTR_ERR(dsi->pixel_clock);
		if (ret != -EPROBE_DEFER)
			dev_err(dev, "Failed to get pixel clock: %d\n", ret);
		return ret;
	}

	/* The esc clock rate is supposed to always be 100Mhz. */
	ret = clk_set_rate(dsi->escape_clock, 100 * 1000000);
	if (ret) {
		dev_err(dev, "Failed to set esc clock: %d\n", ret);
		return ret;
	}

	ret = vc4_dsi_init_phy_clocks(dsi);
	if (ret)
		return ret;

	if (dsi->port == 1)
		vc4->dsi1 = dsi;

	drm_encoder_init(drm, dsi->encoder, &vc4_dsi_encoder_funcs,
			 DRM_MODE_ENCODER_DSI, NULL);
	drm_encoder_helper_add(dsi->encoder, &vc4_dsi_encoder_helper_funcs);

	dsi->connector = vc4_dsi_connector_init(drm, dsi);
	if (IS_ERR(dsi->connector)) {
		ret = PTR_ERR(dsi->connector);
		goto err_destroy_encoder;
	}

	dsi->dsi_host.ops = &vc4_dsi_host_ops;
	dsi->dsi_host.dev = dev;

	mipi_dsi_host_register(&dsi->dsi_host);

	dev_set_drvdata(dev, dsi);

	pm_runtime_enable(dev);

	return 0;

err_destroy_encoder:
	vc4_dsi_encoder_destroy(dsi->encoder);

	return ret;
}


Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt760100.00%1100.00%


Total760100.00%1100.00%






static void vc4_dsi_unbind(struct device *dev, struct device *master,
			   void *data)
{
	struct drm_device *drm = dev_get_drvdata(master);
	struct vc4_dev *vc4 = to_vc4_dev(drm);
	struct vc4_dsi *dsi = dev_get_drvdata(dev);

	pm_runtime_disable(dev);

	vc4_dsi_connector_destroy(dsi->connector);
	vc4_dsi_encoder_destroy(dsi->encoder);

	mipi_dsi_host_unregister(&dsi->dsi_host);

	clk_disable_unprepare(dsi->pll_phy_clock);
	clk_disable_unprepare(dsi->escape_clock);

	if (dsi->port == 1)
		vc4->dsi1 = NULL;
}


Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt105100.00%1100.00%


Total105100.00%1100.00%




static const struct component_ops vc4_dsi_ops = {
	.bind   = vc4_dsi_bind,
	.unbind = vc4_dsi_unbind,
};




static int vc4_dsi_dev_probe(struct platform_device *pdev)
{
	return component_add(&pdev->dev, &vc4_dsi_ops);
}


Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt23100.00%1100.00%


Total23100.00%1100.00%






static int vc4_dsi_dev_remove(struct platform_device *pdev)
{
	component_del(&pdev->dev, &vc4_dsi_ops);
	return 0;
}


Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt25100.00%1100.00%


Total25100.00%1100.00%




struct platform_driver vc4_dsi_driver = {
	.probe = vc4_dsi_dev_probe,
	.remove = vc4_dsi_dev_remove,
	.driver = {
		.name = "vc4_dsi",
		.of_match_table = vc4_dsi_dt_match,
        },
};

Overall Contributors
PersonTokensPropCommitsCommitProp
Eric Anholt7086100.00%1100.00%


Total7086100.00%1100.00%


Directory: drivers/gpu/drm/vc4



Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.
Created with cregit.