Release 4.11 drivers/iio/common/st_sensors/st_sensors_trigger.c
/*
* STMicroelectronics sensors trigger library driver
*
* Copyright 2012-2013 STMicroelectronics Inc.
*
* Denis Ciocca <denis.ciocca@st.com>
*
* Licensed under the GPL-2.
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/slab.h>
#include <linux/iio/iio.h>
#include <linux/iio/trigger.h>
#include <linux/interrupt.h>
#include <linux/iio/common/st_sensors.h>
#include "st_sensors_core.h"
/**
* st_sensors_new_samples_available() - check if more samples came in
* returns:
* 0 - no new samples available
* 1 - new samples available
* negative - error or unknown
*/
static int st_sensors_new_samples_available(struct iio_dev *indio_dev,
struct st_sensor_data *sdata)
{
u8 status;
int ret;
/* How would I know if I can't check it? */
if (!sdata->sensor_settings->drdy_irq.addr_stat_drdy)
return -EINVAL;
/* No scan mask, no interrupt */
if (!indio_dev->active_scan_mask)
return 0;
ret = sdata->tf->read_byte(&sdata->tb, sdata->dev,
sdata->sensor_settings->drdy_irq.addr_stat_drdy,
&status);
if (ret < 0) {
dev_err(sdata->dev,
"error checking samples available\n");
return ret;
}
/*
* the lower bits of .active_scan_mask[0] is directly mapped
* to the channels on the sensor: either bit 0 for
* one-dimensional sensors, or e.g. x,y,z for accelerometers,
* gyroscopes or magnetometers. No sensor use more than 3
* channels, so cut the other status bits here.
*/
status &= 0x07;
if (status & (u8)indio_dev->active_scan_mask[0])
return 1;
return 0;
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| Linus Walleij | 123 | 100.00% | 1 | 100.00% |
| Total | 123 | 100.00% | 1 | 100.00% |
/**
* st_sensors_irq_handler() - top half of the IRQ-based triggers
* @irq: irq number
* @p: private handler data
*/
static irqreturn_t st_sensors_irq_handler(int irq, void *p)
{
struct iio_trigger *trig = p;
struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig);
struct st_sensor_data *sdata = iio_priv(indio_dev);
/* Get the time stamp as close in time as possible */
sdata->hw_timestamp = iio_get_time_ns(indio_dev);
return IRQ_WAKE_THREAD;
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| Linus Walleij | 49 | 92.45% | 1 | 33.33% |
| Grégor Boirie | 3 | 5.66% | 1 | 33.33% |
| Baoyou Xie | 1 | 1.89% | 1 | 33.33% |
| Total | 53 | 100.00% | 3 | 100.00% |
/**
* st_sensors_irq_thread() - bottom half of the IRQ-based triggers
* @irq: irq number
* @p: private handler data
*/
static irqreturn_t st_sensors_irq_thread(int irq, void *p)
{
struct iio_trigger *trig = p;
struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig);
struct st_sensor_data *sdata = iio_priv(indio_dev);
/*
* If this trigger is backed by a hardware interrupt and we have a
* status register, check if this IRQ came from us. Notice that
* we will process also if st_sensors_new_samples_available()
* returns negative: if we can't check status, then poll
* unconditionally.
*/
if (sdata->hw_irq_trigger &&
st_sensors_new_samples_available(indio_dev, sdata)) {
iio_trigger_poll_chained(p);
} else {
dev_dbg(sdata->dev, "spurious IRQ\n");
return IRQ_NONE;
}
/*
* If we have proper level IRQs the handler will be re-entered if
* the line is still active, so return here and come back in through
* the top half if need be.
*/
if (!sdata->edge_irq)
return IRQ_HANDLED;
/*
* If we are using egde IRQs, new samples arrived while processing
* the IRQ and those may be missed unless we pick them here, so poll
* again. If the sensor delivery frequency is very high, this thread
* turns into a polled loop handler.
*/
while (sdata->hw_irq_trigger &&
st_sensors_new_samples_available(indio_dev, sdata)) {
dev_dbg(sdata->dev, "more samples came in during polling\n");
sdata->hw_timestamp = iio_get_time_ns(indio_dev);
iio_trigger_poll_chained(p);
}
return IRQ_HANDLED;
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| Linus Walleij | 128 | 99.22% | 2 | 66.67% |
| Baoyou Xie | 1 | 0.78% | 1 | 33.33% |
| Total | 129 | 100.00% | 3 | 100.00% |
int st_sensors_allocate_trigger(struct iio_dev *indio_dev,
const struct iio_trigger_ops *trigger_ops)
{
int err, irq;
struct st_sensor_data *sdata = iio_priv(indio_dev);
unsigned long irq_trig;
sdata->trig = iio_trigger_alloc("%s-trigger", indio_dev->name);
if (sdata->trig == NULL) {
dev_err(&indio_dev->dev, "failed to allocate iio trigger.\n");
return -ENOMEM;
}
iio_trigger_set_drvdata(sdata->trig, indio_dev);
sdata->trig->ops = trigger_ops;
sdata->trig->dev.parent = sdata->dev;
irq = sdata->get_irq_data_ready(indio_dev);
irq_trig = irqd_get_trigger_type(irq_get_irq_data(irq));
/*
* If the IRQ is triggered on falling edge, we need to mark the
* interrupt as active low, if the hardware supports this.
*/
switch(irq_trig) {
case IRQF_TRIGGER_FALLING:
case IRQF_TRIGGER_LOW:
if (!sdata->sensor_settings->drdy_irq.addr_ihl) {
dev_err(&indio_dev->dev,
"falling/low specified for IRQ "
"but hardware only support rising/high: "
"will request rising/high\n");
if (irq_trig == IRQF_TRIGGER_FALLING)
irq_trig = IRQF_TRIGGER_RISING;
if (irq_trig == IRQF_TRIGGER_LOW)
irq_trig = IRQF_TRIGGER_HIGH;
} else {
/* Set up INT active low i.e. falling edge */
err = st_sensors_write_data_with_mask(indio_dev,
sdata->sensor_settings->drdy_irq.addr_ihl,
sdata->sensor_settings->drdy_irq.mask_ihl, 1);
if (err < 0)
goto iio_trigger_free;
dev_info(&indio_dev->dev,
"interrupts on the falling edge or "
"active low level\n");
}
break;
case IRQF_TRIGGER_RISING:
dev_info(&indio_dev->dev,
"interrupts on the rising edge\n");
break;
case IRQF_TRIGGER_HIGH:
dev_info(&indio_dev->dev,
"interrupts active high level\n");
break;
default:
/* This is the most preferred mode, if possible */
dev_err(&indio_dev->dev,
"unsupported IRQ trigger specified (%lx), enforce "
"rising edge\n", irq_trig);
irq_trig = IRQF_TRIGGER_RISING;
}
/* Tell the interrupt handler that we're dealing with edges */
if (irq_trig == IRQF_TRIGGER_FALLING ||
irq_trig == IRQF_TRIGGER_RISING)
sdata->edge_irq = true;
else
/*
* If we're not using edges (i.e. level interrupts) we
* just mask off the IRQ, handle one interrupt, then
* if the line is still low, we return to the
* interrupt handler top half again and start over.
*/
irq_trig |= IRQF_ONESHOT;
/*
* If the interrupt pin is Open Drain, by definition this
* means that the interrupt line may be shared with other
* peripherals. But to do this we also need to have a status
* register and mask to figure out if this sensor was firing
* the IRQ or not, so we can tell the interrupt handle that
* it was "our" interrupt.
*/
if (sdata->int_pin_open_drain &&
sdata->sensor_settings->drdy_irq.addr_stat_drdy)
irq_trig |= IRQF_SHARED;
err = request_threaded_irq(sdata->get_irq_data_ready(indio_dev),
st_sensors_irq_handler,
st_sensors_irq_thread,
irq_trig,
sdata->trig->name,
sdata->trig);
if (err) {
dev_err(&indio_dev->dev, "failed to request trigger IRQ.\n");
goto iio_trigger_free;
}
err = iio_trigger_register(sdata->trig);
if (err < 0) {
dev_err(&indio_dev->dev, "failed to register iio trigger.\n");
goto iio_trigger_register_error;
}
indio_dev->trig = iio_trigger_get(sdata->trig);
return 0;
iio_trigger_register_error:
free_irq(sdata->get_irq_data_ready(indio_dev), sdata->trig);
iio_trigger_free:
iio_trigger_free(sdata->trig);
return err;
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| Linus Walleij | 243 | 55.73% | 5 | 62.50% |
| Denis Ciocca | 161 | 36.93% | 1 | 12.50% |
| Crestez Dan Leonard | 29 | 6.65% | 1 | 12.50% |
| Srinivas Pandruvada | 3 | 0.69% | 1 | 12.50% |
| Total | 436 | 100.00% | 8 | 100.00% |
EXPORT_SYMBOL(st_sensors_allocate_trigger);
void st_sensors_deallocate_trigger(struct iio_dev *indio_dev)
{
struct st_sensor_data *sdata = iio_priv(indio_dev);
iio_trigger_unregister(sdata->trig);
free_irq(sdata->get_irq_data_ready(indio_dev), sdata->trig);
iio_trigger_free(sdata->trig);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| Denis Ciocca | 48 | 100.00% | 1 | 100.00% |
| Total | 48 | 100.00% | 1 | 100.00% |
EXPORT_SYMBOL(st_sensors_deallocate_trigger);
int st_sensors_validate_device(struct iio_trigger *trig,
struct iio_dev *indio_dev)
{
struct iio_dev *indio = iio_trigger_get_drvdata(trig);
if (indio != indio_dev)
return -EINVAL;
return 0;
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| Linus Walleij | 38 | 100.00% | 1 | 100.00% |
| Total | 38 | 100.00% | 1 | 100.00% |
EXPORT_SYMBOL(st_sensors_validate_device);
MODULE_AUTHOR("Denis Ciocca <denis.ciocca@st.com>");
MODULE_DESCRIPTION("STMicroelectronics ST-sensors trigger");
MODULE_LICENSE("GPL v2");
Overall Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| Linus Walleij | 592 | 66.89% | 5 | 50.00% |
| Denis Ciocca | 256 | 28.93% | 1 | 10.00% |
| Crestez Dan Leonard | 29 | 3.28% | 1 | 10.00% |
| Srinivas Pandruvada | 3 | 0.34% | 1 | 10.00% |
| Grégor Boirie | 3 | 0.34% | 1 | 10.00% |
| Baoyou Xie | 2 | 0.23% | 1 | 10.00% |
| Total | 885 | 100.00% | 10 | 100.00% |
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.