cregit-Linux how code gets into the kernel

Release 4.11 drivers/input/touchscreen/wm9713.c

/*
 * wm9713.c  --  Codec touch driver for Wolfson WM9713 AC97 Codec.
 *
 * Copyright 2003, 2004, 2005, 2006, 2007, 2008 Wolfson Microelectronics PLC.
 * Author: Liam Girdwood <lrg@slimlogic.co.uk>
 * Parts Copyright : Ian Molton <spyro@f2s.com>
 *                   Andrew Zabolotny <zap@homelink.ru>
 *                   Russell King <rmk@arm.linux.org.uk>
 *
 *  This program is free software; you can redistribute  it and/or modify it
 *  under  the terms of  the GNU General  Public License as published by the
 *  Free Software Foundation;  either version 2 of the  License, or (at your
 *  option) any later version.
 *
 */

#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/kernel.h>
#include <linux/input.h>
#include <linux/delay.h>
#include <linux/bitops.h>
#include <linux/wm97xx.h>


#define TS_NAME			"wm97xx"

#define WM9713_VERSION		"1.00"

#define DEFAULT_PRESSURE	0xb0c0

/*
 * Module parameters
 */

/*
 * Set internal pull up for pen detect.
 *
 * Pull up is in the range 1.02k (least sensitive) to 64k (most sensitive)
 * i.e. pull up resistance = 64k Ohms / rpu.
 *
 * Adjust this value if you are having problems with pen detect not
 * detecting any down event.
 */

static int rpu = 8;
module_param(rpu, int, 0);
MODULE_PARM_DESC(rpu, "Set internal pull up resistor for pen detect.");

/*
 * Set current used for pressure measurement.
 *
 * Set pil = 2 to use 400uA
 *     pil = 1 to use 200uA and
 *     pil = 0 to disable pressure measurement.
 *
 * This is used to increase the range of values returned by the adc
 * when measureing touchpanel pressure.
 */

static int pil;
module_param(pil, int, 0);
MODULE_PARM_DESC(pil, "Set current used for pressure measurement.");

/*
 * Set threshold for pressure measurement.
 *
 * Pen down pressure below threshold is ignored.
 */

static int pressure = DEFAULT_PRESSURE & 0xfff;
module_param(pressure, int, 0);
MODULE_PARM_DESC(pressure, "Set threshold for pressure measurement.");

/*
 * Set adc sample delay.
 *
 * For accurate touchpanel measurements, some settling time may be
 * required between the switch matrix applying a voltage across the
 * touchpanel plate and the ADC sampling the signal.
 *
 * This delay can be set by setting delay = n, where n is the array
 * position of the delay in the array delay_table below.
 * Long delays > 1ms are supported for completeness, but are not
 * recommended.
 */

static int delay = 4;
module_param(delay, int, 0);
MODULE_PARM_DESC(delay, "Set adc sample delay.");

/*
 * Set five_wire = 1 to use a 5 wire touchscreen.
 *
 * NOTE: Five wire mode does not allow for readback of pressure.
 */

static int five_wire;
module_param(five_wire, int, 0);
MODULE_PARM_DESC(five_wire, "Set to '1' to use 5-wire touchscreen.");

/*
 * Set adc mask function.
 *
 * Sources of glitch noise, such as signals driving an LCD display, may feed
 * through to the touch screen plates and affect measurement accuracy. In
 * order to minimise this, a signal may be applied to the MASK pin to delay or
 * synchronise the sampling.
 *
 * 0 = No delay or sync
 * 1 = High on pin stops conversions
 * 2 = Edge triggered, edge on pin delays conversion by delay param (above)
 * 3 = Edge triggered, edge on pin starts conversion after delay param
 */

static int mask;
module_param(mask, int, 0);
MODULE_PARM_DESC(mask, "Set adc mask function.");

/*
 * Coordinate Polling Enable.
 *
 * Set to 1 to enable coordinate polling. e.g. x,y[,p] is sampled together
 * for every poll.
 */

static int coord;
module_param(coord, int, 0);
MODULE_PARM_DESC(coord, "Polling coordinate mode");

/*
 * ADC sample delay times in uS
 */

static const int delay_table[] = {
	21,    /* 1 AC97 Link frames */
	42,    /* 2 */
	84,    /* 4 */
	167,   /* 8 */
	333,   /* 16 */
	667,   /* 32 */
	1000,  /* 48 */
	1333,  /* 64 */
	2000,  /* 96 */
	2667,  /* 128 */
	3333,  /* 160 */
	4000,  /* 192 */
	4667,  /* 224 */
	5333,  /* 256 */
	6000,  /* 288 */
	0      /* No delay, switch matrix always on */
};

/*
 * Delay after issuing a POLL command.
 *
 * The delay is 3 AC97 link frames + the touchpanel settling delay
 */

static inline void poll_delay(int d) { udelay(3 * AC97_LINK_FRAME + delay_table[d]); }

Contributors

PersonTokensPropCommitsCommitProp
Mark Brown22100.00%1100.00%
Total22100.00%1100.00%

/* * set up the physical settings of the WM9713 */
static void wm9713_phy_init(struct wm97xx *wm) { u16 dig1 = 0, dig2, dig3; /* default values */ dig2 = WM97XX_DELAY(4) | WM97XX_SLT(5); dig3 = WM9712_RPU(1); /* rpu */ if (rpu) { dig3 &= 0xffc0; dig3 |= WM9712_RPU(rpu); dev_info(wm->dev, "setting pen detect pull-up to %d Ohms\n", 64000 / rpu); } /* Five wire panel? */ if (five_wire) { dig3 |= WM9713_45W; dev_info(wm->dev, "setting 5-wire touchscreen mode."); if (pil) { dev_warn(wm->dev, "Pressure measurement not supported in 5 " "wire mode, disabling\n"); pil = 0; } } /* touchpanel pressure */ if (pil == 2) { dig3 |= WM9712_PIL; dev_info(wm->dev, "setting pressure measurement current to 400uA."); } else if (pil) dev_info(wm->dev, "setting pressure measurement current to 200uA."); if (!pil) pressure = 0; /* sample settling delay */ if (delay < 0 || delay > 15) { dev_info(wm->dev, "supplied delay out of range."); delay = 4; dev_info(wm->dev, "setting adc sample delay to %d u Secs.", delay_table[delay]); } dig2 &= 0xff0f; dig2 |= WM97XX_DELAY(delay); /* mask */ dig3 |= ((mask & 0x3) << 4); if (coord) dig3 |= WM9713_WAIT; wm->misc = wm97xx_reg_read(wm, 0x5a); wm97xx_reg_write(wm, AC97_WM9713_DIG1, dig1); wm97xx_reg_write(wm, AC97_WM9713_DIG2, dig2); wm97xx_reg_write(wm, AC97_WM9713_DIG3, dig3); wm97xx_reg_write(wm, AC97_GPIO_STICKY, 0x0); }

Contributors

PersonTokensPropCommitsCommitProp
Mark Brown275100.00%2100.00%
Total275100.00%2100.00%


static void wm9713_dig_enable(struct wm97xx *wm, int enable) { u16 val; if (enable) { val = wm97xx_reg_read(wm, AC97_EXTENDED_MID); wm97xx_reg_write(wm, AC97_EXTENDED_MID, val & 0x7fff); wm97xx_reg_write(wm, AC97_WM9713_DIG3, wm->dig[2] | WM97XX_PRP_DET_DIG); wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD); /* dummy read */ } else { wm97xx_reg_write(wm, AC97_WM9713_DIG3, wm->dig[2] & ~WM97XX_PRP_DET_DIG); val = wm97xx_reg_read(wm, AC97_EXTENDED_MID); wm97xx_reg_write(wm, AC97_EXTENDED_MID, val | 0x8000); } }

Contributors

PersonTokensPropCommitsCommitProp
Mark Brown107100.00%1100.00%
Total107100.00%1100.00%


static void wm9713_dig_restore(struct wm97xx *wm) { wm97xx_reg_write(wm, AC97_WM9713_DIG1, wm->dig_save[0]); wm97xx_reg_write(wm, AC97_WM9713_DIG2, wm->dig_save[1]); wm97xx_reg_write(wm, AC97_WM9713_DIG3, wm->dig_save[2]); }

Contributors

PersonTokensPropCommitsCommitProp
Mark Brown53100.00%1100.00%
Total53100.00%1100.00%


static void wm9713_aux_prepare(struct wm97xx *wm) { memcpy(wm->dig_save, wm->dig, sizeof(wm->dig)); wm97xx_reg_write(wm, AC97_WM9713_DIG1, 0); wm97xx_reg_write(wm, AC97_WM9713_DIG2, 0); wm97xx_reg_write(wm, AC97_WM9713_DIG3, WM97XX_PRP_DET_DIG); }

Contributors

PersonTokensPropCommitsCommitProp
Mark Brown56100.00%1100.00%
Total56100.00%1100.00%


static inline int is_pden(struct wm97xx *wm) { return wm->dig[2] & WM9713_PDEN; }

Contributors

PersonTokensPropCommitsCommitProp
Mark Brown22100.00%1100.00%
Total22100.00%1100.00%

/* * Read a sample from the WM9713 adc in polling mode. */
static int wm9713_poll_sample(struct wm97xx *wm, int adcsel, int *sample) { u16 dig1; int timeout = 5 * delay; bool wants_pen = adcsel & WM97XX_PEN_DOWN; if (wants_pen && !wm->pen_probably_down) { u16 data = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD); if (!(data & WM97XX_PEN_DOWN)) return RC_PENUP; wm->pen_probably_down = 1; } /* set up digitiser */ dig1 = wm97xx_reg_read(wm, AC97_WM9713_DIG1); dig1 &= ~WM9713_ADCSEL_MASK; /* WM97XX_ADCSEL_* channels need to be converted to WM9713 format */ dig1 |= 1 << ((adcsel & WM97XX_ADCSEL_MASK) >> 12); if (wm->mach_ops && wm->mach_ops->pre_sample) wm->mach_ops->pre_sample(adcsel); wm97xx_reg_write(wm, AC97_WM9713_DIG1, dig1 | WM9713_POLL); /* wait 3 AC97 time slots + delay for conversion */ poll_delay(delay); /* wait for POLL to go low */ while ((wm97xx_reg_read(wm, AC97_WM9713_DIG1) & WM9713_POLL) && timeout) { udelay(AC97_LINK_FRAME); timeout--; } if (timeout <= 0) { /* If PDEN is set, we can get a timeout when pen goes up */ if (is_pden(wm)) wm->pen_probably_down = 0; else dev_dbg(wm->dev, "adc sample timeout"); return RC_PENUP; } *sample = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD); if (wm->mach_ops && wm->mach_ops->post_sample) wm->mach_ops->post_sample(adcsel); /* check we have correct sample */ if ((*sample ^ adcsel) & WM97XX_ADCSEL_MASK) { dev_dbg(wm->dev, "adc wrong sample, wanted %x got %x", adcsel & WM97XX_ADCSEL_MASK, *sample & WM97XX_ADCSEL_MASK); return RC_PENUP; } if (wants_pen && !(*sample & WM97XX_PEN_DOWN)) { wm->pen_probably_down = 0; return RC_PENUP; } return RC_VALID; }

Contributors

PersonTokensPropCommitsCommitProp
Mark Brown26188.47%125.00%
Wolfram Sang3411.53%375.00%
Total295100.00%4100.00%

/* * Read a coordinate from the WM9713 adc in polling mode. */
static int wm9713_poll_coord(struct wm97xx *wm, struct wm97xx_data *data) { u16 dig1; int timeout = 5 * delay; if (!wm->pen_probably_down) { u16 val = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD); if (!(val & WM97XX_PEN_DOWN)) return RC_PENUP; wm->pen_probably_down = 1; } /* set up digitiser */ dig1 = wm97xx_reg_read(wm, AC97_WM9713_DIG1); dig1 &= ~WM9713_ADCSEL_MASK; if (pil) dig1 |= WM9713_ADCSEL_PRES; if (wm->mach_ops && wm->mach_ops->pre_sample) wm->mach_ops->pre_sample(WM97XX_ADCSEL_X | WM97XX_ADCSEL_Y); wm97xx_reg_write(wm, AC97_WM9713_DIG1, dig1 | WM9713_POLL | WM9713_COO); /* wait 3 AC97 time slots + delay for conversion */ poll_delay(delay); data->x = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD); /* wait for POLL to go low */ while ((wm97xx_reg_read(wm, AC97_WM9713_DIG1) & WM9713_POLL) && timeout) { udelay(AC97_LINK_FRAME); timeout--; } if (timeout <= 0) { /* If PDEN is set, we can get a timeout when pen goes up */ if (is_pden(wm)) wm->pen_probably_down = 0; else dev_dbg(wm->dev, "adc sample timeout"); return RC_PENUP; } /* read back data */ data->y = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD); if (pil) data->p = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD); else data->p = DEFAULT_PRESSURE; if (wm->mach_ops && wm->mach_ops->post_sample) wm->mach_ops->post_sample(WM97XX_ADCSEL_X | WM97XX_ADCSEL_Y); /* check we have correct sample */ if (!(data->x & WM97XX_ADCSEL_X) || !(data->y & WM97XX_ADCSEL_Y)) goto err; if (pil && !(data->p & WM97XX_ADCSEL_PRES)) goto err; if (!(data->x & WM97XX_PEN_DOWN) || !(data->y & WM97XX_PEN_DOWN)) { wm->pen_probably_down = 0; return RC_PENUP; } return RC_VALID; err: return 0; }

Contributors

PersonTokensPropCommitsCommitProp
Mark Brown336100.00%1100.00%
Total336100.00%1100.00%

/* * Sample the WM9713 touchscreen in polling mode */
static int wm9713_poll_touch(struct wm97xx *wm, struct wm97xx_data *data) { int rc; if (coord) { rc = wm9713_poll_coord(wm, data); if (rc != RC_VALID) return rc; } else { rc = wm9713_poll_sample(wm, WM97XX_ADCSEL_X | WM97XX_PEN_DOWN, &data->x); if (rc != RC_VALID) return rc; rc = wm9713_poll_sample(wm, WM97XX_ADCSEL_Y | WM97XX_PEN_DOWN, &data->y); if (rc != RC_VALID) return rc; if (pil) { rc = wm9713_poll_sample(wm, WM97XX_ADCSEL_PRES | WM97XX_PEN_DOWN, &data->p); if (rc != RC_VALID) return rc; } else data->p = DEFAULT_PRESSURE; } return RC_VALID; }

Contributors

PersonTokensPropCommitsCommitProp
Mark Brown12893.43%133.33%
Wolfram Sang96.57%266.67%
Total137100.00%3100.00%

/* * Enable WM9713 continuous mode, i.e. touch data is streamed across * an AC97 slot */
static int wm9713_acc_enable(struct wm97xx *wm, int enable) { u16 dig1, dig2, dig3; int ret = 0; dig1 = wm->dig[0]; dig2 = wm->dig[1]; dig3 = wm->dig[2]; if (enable) { /* continuous mode */ if (wm->mach_ops->acc_startup && (ret = wm->mach_ops->acc_startup(wm)) < 0) return ret; dig1 &= ~WM9713_ADCSEL_MASK; dig1 |= WM9713_CTC | WM9713_COO | WM9713_ADCSEL_X | WM9713_ADCSEL_Y; if (pil) dig1 |= WM9713_ADCSEL_PRES; dig2 &= ~(WM97XX_DELAY_MASK | WM97XX_SLT_MASK | WM97XX_CM_RATE_MASK); dig2 |= WM97XX_SLEN | WM97XX_DELAY(delay) | WM97XX_SLT(wm->acc_slot) | WM97XX_RATE(wm->acc_rate); dig3 |= WM9713_PDEN; } else { dig1 &= ~(WM9713_CTC | WM9713_COO); dig2 &= ~WM97XX_SLEN; dig3 &= ~WM9713_PDEN; if (wm->mach_ops->acc_shutdown) wm->mach_ops->acc_shutdown(wm); } wm97xx_reg_write(wm, AC97_WM9713_DIG1, dig1); wm97xx_reg_write(wm, AC97_WM9713_DIG2, dig2); wm97xx_reg_write(wm, AC97_WM9713_DIG3, dig3); return ret; }

Contributors

PersonTokensPropCommitsCommitProp
Mark Brown21599.54%150.00%
Lucas De Marchi10.46%150.00%
Total216100.00%2100.00%

struct wm97xx_codec_drv wm9713_codec = { .id = WM9713_ID2, .name = "wm9713", .poll_sample = wm9713_poll_sample, .poll_touch = wm9713_poll_touch, .acc_enable = wm9713_acc_enable, .phy_init = wm9713_phy_init, .dig_enable = wm9713_dig_enable, .dig_restore = wm9713_dig_restore, .aux_prepare = wm9713_aux_prepare, }; EXPORT_SYMBOL_GPL(wm9713_codec); /* Module information */ MODULE_AUTHOR("Liam Girdwood <lrg@slimlogic.co.uk>"); MODULE_DESCRIPTION("WM9713 Touch Screen Driver"); MODULE_LICENSE("GPL");

Overall Contributors

PersonTokensPropCommitsCommitProp
Mark Brown179797.45%225.00%
Wolfram Sang432.33%337.50%
Liam Girdwood20.11%112.50%
Masanari Iida10.05%112.50%
Lucas De Marchi10.05%112.50%
Total1844100.00%8100.00%
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.
Created with cregit.