Release 4.11 drivers/media/usb/em28xx/em28xx-reg.h
#define EM_GPIO_0 (1 << 0)
#define EM_GPIO_1 (1 << 1)
#define EM_GPIO_2 (1 << 2)
#define EM_GPIO_3 (1 << 3)
#define EM_GPIO_4 (1 << 4)
#define EM_GPIO_5 (1 << 5)
#define EM_GPIO_6 (1 << 6)
#define EM_GPIO_7 (1 << 7)
#define EM_GPO_0 (1 << 0)
#define EM_GPO_1 (1 << 1)
#define EM_GPO_2 (1 << 2)
#define EM_GPO_3 (1 << 3)
/* em28xx endpoints */
/* 0x82: (always ?) analog */
#define EM28XX_EP_AUDIO 0x83
/* 0x84: digital or analog */
/* em2800 registers */
#define EM2800_R08_AUDIOSRC 0x08
/* em28xx registers */
#define EM28XX_R00_CHIPCFG 0x00
/* em28xx Chip Configuration 0x00 */
#define EM2860_CHIPCFG_VENDOR_AUDIO 0x80
#define EM2860_CHIPCFG_I2S_VOLUME_CAPABLE 0x40
#define EM2820_CHIPCFG_I2S_3_SAMPRATES 0x30
#define EM2860_CHIPCFG_I2S_5_SAMPRATES 0x30
#define EM2820_CHIPCFG_I2S_1_SAMPRATE 0x20
#define EM2860_CHIPCFG_I2S_3_SAMPRATES 0x20
#define EM28XX_CHIPCFG_AC97 0x10
#define EM28XX_CHIPCFG_AUDIOMASK 0x30
#define EM28XX_R01_CHIPCFG2 0x01
/* em28xx Chip Configuration 2 0x01 */
#define EM28XX_CHIPCFG2_TS_PRESENT 0x10
#define EM28XX_CHIPCFG2_TS_REQ_INTERVAL_MASK 0x0c
/* bits 3-2 */
#define EM28XX_CHIPCFG2_TS_REQ_INTERVAL_1MF 0x00
#define EM28XX_CHIPCFG2_TS_REQ_INTERVAL_2MF 0x04
#define EM28XX_CHIPCFG2_TS_REQ_INTERVAL_4MF 0x08
#define EM28XX_CHIPCFG2_TS_REQ_INTERVAL_8MF 0x0c
#define EM28XX_CHIPCFG2_TS_PACKETSIZE_MASK 0x03
/* bits 0-1 */
#define EM28XX_CHIPCFG2_TS_PACKETSIZE_188 0x00
#define EM28XX_CHIPCFG2_TS_PACKETSIZE_376 0x01
#define EM28XX_CHIPCFG2_TS_PACKETSIZE_564 0x02
#define EM28XX_CHIPCFG2_TS_PACKETSIZE_752 0x03
/* GPIO/GPO registers */
#define EM2880_R04_GPO 0x04
/* em2880-em2883 only */
#define EM2820_R08_GPIO_CTRL 0x08
/* em2820-em2873/83 only */
#define EM2820_R09_GPIO_STATE 0x09
/* em2820-em2873/83 only */
#define EM28XX_R06_I2C_CLK 0x06
/* em28xx I2C Clock Register (0x06) */
#define EM28XX_I2C_CLK_ACK_LAST_READ 0x80
#define EM28XX_I2C_CLK_WAIT_ENABLE 0x40
#define EM28XX_I2C_EEPROM_ON_BOARD 0x08
#define EM28XX_I2C_EEPROM_KEY_VALID 0x04
#define EM2874_I2C_SECONDARY_BUS_SELECT 0x04
/* em2874 has two i2c busses */
#define EM28XX_I2C_FREQ_1_5_MHZ 0x03
/* bus frequency (bits [1-0]) */
#define EM28XX_I2C_FREQ_25_KHZ 0x02
#define EM28XX_I2C_FREQ_400_KHZ 0x01
#define EM28XX_I2C_FREQ_100_KHZ 0x00
#define EM28XX_R0A_CHIPID 0x0a
#define EM28XX_R0C_USBSUSP 0x0c
#define EM28XX_R0C_USBSUSP_SNAPSHOT 0x20
/* 1=button pressed, needs reset */
#define EM28XX_R0E_AUDIOSRC 0x0e
#define EM28XX_R0F_XCLK 0x0f
/* em28xx XCLK Register (0x0f) */
#define EM28XX_XCLK_AUDIO_UNMUTE 0x80
/* otherwise audio muted */
#define EM28XX_XCLK_I2S_MSB_TIMING 0x40
/* otherwise standard timing */
#define EM28XX_XCLK_IR_RC5_MODE 0x20
/* otherwise NEC mode */
#define EM28XX_XCLK_IR_NEC_CHK_PARITY 0x10
#define EM28XX_XCLK_FREQUENCY_30MHZ 0x00
/* Freq. select (bits [3-0]) */
#define EM28XX_XCLK_FREQUENCY_15MHZ 0x01
#define EM28XX_XCLK_FREQUENCY_10MHZ 0x02
#define EM28XX_XCLK_FREQUENCY_7_5MHZ 0x03
#define EM28XX_XCLK_FREQUENCY_6MHZ 0x04
#define EM28XX_XCLK_FREQUENCY_5MHZ 0x05
#define EM28XX_XCLK_FREQUENCY_4_3MHZ 0x06
#define EM28XX_XCLK_FREQUENCY_12MHZ 0x07
#define EM28XX_XCLK_FREQUENCY_20MHZ 0x08
#define EM28XX_XCLK_FREQUENCY_20MHZ_2 0x09
#define EM28XX_XCLK_FREQUENCY_48MHZ 0x0a
#define EM28XX_XCLK_FREQUENCY_24MHZ 0x0b
#define EM28XX_R10_VINMODE 0x10
#define EM28XX_R11_VINCTRL 0x11
/* em28xx Video Input Control Register 0x11 */
#define EM28XX_VINCTRL_VBI_SLICED 0x80
#define EM28XX_VINCTRL_VBI_RAW 0x40
#define EM28XX_VINCTRL_VOUT_MODE_IN 0x20
/* HREF,VREF,VACT in output */
#define EM28XX_VINCTRL_CCIR656_ENABLE 0x10
#define EM28XX_VINCTRL_VBI_16BIT_RAW 0x08
/* otherwise 8-bit raw */
#define EM28XX_VINCTRL_FID_ON_HREF 0x04
#define EM28XX_VINCTRL_DUAL_EDGE_STROBE 0x02
#define EM28XX_VINCTRL_INTERLACED 0x01
#define EM28XX_R12_VINENABLE 0x12
/* */
#define EM28XX_R14_GAMMA 0x14
#define EM28XX_R15_RGAIN 0x15
#define EM28XX_R16_GGAIN 0x16
#define EM28XX_R17_BGAIN 0x17
#define EM28XX_R18_ROFFSET 0x18
#define EM28XX_R19_GOFFSET 0x19
#define EM28XX_R1A_BOFFSET 0x1a
#define EM28XX_R1B_OFLOW 0x1b
#define EM28XX_R1C_HSTART 0x1c
#define EM28XX_R1D_VSTART 0x1d
#define EM28XX_R1E_CWIDTH 0x1e
#define EM28XX_R1F_CHEIGHT 0x1f
#define EM28XX_R20_YGAIN 0x20
/* contrast [0:4] */
#define CONTRAST_DEFAULT 0x10
#define EM28XX_R21_YOFFSET 0x21
/* brightness */
/* signed */
#define BRIGHTNESS_DEFAULT 0x00
#define EM28XX_R22_UVGAIN 0x22
/* saturation [0:4] */
#define SATURATION_DEFAULT 0x10
#define EM28XX_R23_UOFFSET 0x23
/* blue balance */
/* signed */
#define BLUE_BALANCE_DEFAULT 0x00
#define EM28XX_R24_VOFFSET 0x24
/* red balance */
/* signed */
#define RED_BALANCE_DEFAULT 0x00
#define EM28XX_R25_SHARPNESS 0x25
/* sharpness [0:4] */
#define SHARPNESS_DEFAULT 0x00
#define EM28XX_R26_COMPR 0x26
#define EM28XX_R27_OUTFMT 0x27
/* em28xx Output Format Register (0x27) */
#define EM28XX_OUTFMT_RGB_8_RGRG 0x00
#define EM28XX_OUTFMT_RGB_8_GRGR 0x01
#define EM28XX_OUTFMT_RGB_8_GBGB 0x02
#define EM28XX_OUTFMT_RGB_8_BGBG 0x03
#define EM28XX_OUTFMT_RGB_16_656 0x04
#define EM28XX_OUTFMT_RGB_8_BAYER 0x08
/* Pattern in Reg 0x10[1-0] */
#define EM28XX_OUTFMT_YUV211 0x10
#define EM28XX_OUTFMT_YUV422_Y0UY1V 0x14
#define EM28XX_OUTFMT_YUV422_Y1UY0V 0x15
#define EM28XX_OUTFMT_YUV411 0x18
#define EM28XX_R28_XMIN 0x28
#define EM28XX_R29_XMAX 0x29
#define EM28XX_R2A_YMIN 0x2a
#define EM28XX_R2B_YMAX 0x2b
#define EM28XX_R30_HSCALELOW 0x30
#define EM28XX_R31_HSCALEHIGH 0x31
#define EM28XX_R32_VSCALELOW 0x32
#define EM28XX_R33_VSCALEHIGH 0x33
#define EM28XX_HVSCALE_MAX 0x3fff
/* => 20% */
#define EM28XX_R34_VBI_START_H 0x34
#define EM28XX_R35_VBI_START_V 0x35
/*
* NOTE: the EM276x (and EM25xx, EM277x/8x ?) (camera bridges) use these
* registers for a different unknown purpose.
* => register 0x34 is set to capture width / 16
* => register 0x35 is set to capture height / 16
*/
#define EM28XX_R36_VBI_WIDTH 0x36
#define EM28XX_R37_VBI_HEIGHT 0x37
#define EM28XX_R40_AC97LSB 0x40
#define EM28XX_R41_AC97MSB 0x41
#define EM28XX_R42_AC97ADDR 0x42
#define EM28XX_R43_AC97BUSY 0x43
#define EM28XX_R45_IR 0x45
/* 0x45 bit 7 - parity bit
bits 6-0 - count
0x46 IR brand
0x47 IR data
*/
/* em2874 registers */
#define EM2874_R50_IR_CONFIG 0x50
#define EM2874_R51_IR 0x51
#define EM2874_R5D_TS1_PKT_SIZE 0x5d
#define EM2874_R5E_TS2_PKT_SIZE 0x5e
/*
* For both TS1 and TS2, In isochronous mode:
* 0x01 188 bytes
* 0x02 376 bytes
* 0x03 564 bytes
* 0x04 752 bytes
* 0x05 940 bytes
* In bulk mode:
* 0x01..0xff total packet count in 188-byte
*/
#define EM2874_R5F_TS_ENABLE 0x5f
/* em2874/174/84, em25xx, em276x/7x/8x GPIO registers */
/*
* NOTE: not all ports are bonded out;
* Some ports are multiplexed with special function I/O
*/
#define EM2874_R80_GPIO_P0_CTRL 0x80
#define EM2874_R81_GPIO_P1_CTRL 0x81
#define EM2874_R82_GPIO_P2_CTRL 0x82
#define EM2874_R83_GPIO_P3_CTRL 0x83
#define EM2874_R84_GPIO_P0_STATE 0x84
#define EM2874_R85_GPIO_P1_STATE 0x85
#define EM2874_R86_GPIO_P2_STATE 0x86
#define EM2874_R87_GPIO_P3_STATE 0x87
/* em2874 IR config register (0x50) */
#define EM2874_IR_NEC 0x00
#define EM2874_IR_NEC_NO_PARITY 0x01
#define EM2874_IR_RC5 0x04
#define EM2874_IR_RC6_MODE_0 0x08
#define EM2874_IR_RC6_MODE_6A 0x0b
/* em2874 Transport Stream Enable Register (0x5f) */
#define EM2874_TS1_CAPTURE_ENABLE (1 << 0)
#define EM2874_TS1_FILTER_ENABLE (1 << 1)
#define EM2874_TS1_NULL_DISCARD (1 << 2)
#define EM2874_TS2_CAPTURE_ENABLE (1 << 4)
#define EM2874_TS2_FILTER_ENABLE (1 << 5)
#define EM2874_TS2_NULL_DISCARD (1 << 6)
/* register settings */
#define EM2800_AUDIO_SRC_TUNER 0x0d
#define EM2800_AUDIO_SRC_LINE 0x0c
#define EM28XX_AUDIO_SRC_TUNER 0xc0
#define EM28XX_AUDIO_SRC_LINE 0x80
/* FIXME: Need to be populated with the other chip ID's */
enum em28xx_chip_id {
CHIP_ID_EM2800 = 7,
CHIP_ID_EM2710 = 17,
CHIP_ID_EM2820 = 18, /* Also used by some em2710 */
CHIP_ID_EM2840 = 20,
CHIP_ID_EM2750 = 33,
CHIP_ID_EM2860 = 34,
CHIP_ID_EM2870 = 35,
CHIP_ID_EM2883 = 36,
CHIP_ID_EM2765 = 54,
CHIP_ID_EM2874 = 65,
CHIP_ID_EM2884 = 68,
CHIP_ID_EM28174 = 113,
CHIP_ID_EM28178 = 114,
};
/*
* Registers used by em202
*/
/* EMP202 vendor registers */
#define EM202_EXT_MODEM_CTRL 0x3e
#define EM202_GPIO_CONF 0x4c
#define EM202_GPIO_POLARITY 0x4e
#define EM202_GPIO_STICKY 0x50
#define EM202_GPIO_MASK 0x52
#define EM202_GPIO_STATUS 0x54
#define EM202_SPDIF_OUT_SEL 0x6a
#define EM202_ANTIPOP 0x72
#define EM202_EAPD_GPIO_ACCESS 0x74
Overall Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| Devin Heitmueller | 349 | 44.12% | 14 | 36.84% |
| Mauro Carvalho Chehab | 319 | 40.33% | 10 | 26.32% |
| Frank Schäfer | 100 | 12.64% | 9 | 23.68% |
| Olli Salonen | 9 | 1.14% | 1 | 2.63% |
| Antti Palosaari | 8 | 1.01% | 2 | 5.26% |
| Holger Nelson | 5 | 0.63% | 1 | 2.63% |
| Ezequiel García | 1 | 0.13% | 1 | 2.63% |
| Total | 791 | 100.00% | 38 | 100.00% |
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.