cregit-Linux how code gets into the kernel

Release 4.11 drivers/net/usb/pegasus.h

Directory: drivers/net/usb
/*
 * Copyright (c) 1999-2013 Petko Manolov (petkan@nucleusys.com)
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as published
 * by the Free Software Foundation.
 */


#ifndef	PEGASUS_DEV


#define	PEGASUS_II		0x80000000

#define	HAS_HOME_PNA		0x40000000


#define	PEGASUS_MTU		1536


#define	EPROM_WRITE		0x01

#define	EPROM_READ		0x02

#define	EPROM_DONE		0x04

#define	EPROM_WR_ENABLE		0x10

#define	EPROM_LOAD		0x20


#define	PHY_DONE		0x80

#define	PHY_READ		0x40

#define	PHY_WRITE		0x20

#define	DEFAULT_GPIO_RESET	0x24

#define	DEFAULT_GPIO_SET	0x26


#define	PEGASUS_PRESENT		0x00000001

#define	PEGASUS_TX_BUSY		0x00000004

#define	PEGASUS_RX_BUSY		0x00000008

#define	CTRL_URB_RUNNING	0x00000010

#define	CTRL_URB_SLEEP		0x00000020

#define	PEGASUS_UNPLUG		0x00000040

#define	PEGASUS_RX_URB_FAIL	0x00000080


#define	RX_MULTICAST		2

#define	RX_PROMISCUOUS		4


#define	REG_TIMEOUT		(HZ)

#define	PEGASUS_TX_TIMEOUT	(HZ*10)


#define	TX_UNDERRUN		0x80

#define	EXCESSIVE_COL		0x40

#define	LATE_COL		0x20

#define	NO_CARRIER		0x10

#define	LOSS_CARRIER		0x08

#define	JABBER_TIMEOUT		0x04


#define	LINK_STATUS		0x01


#define	PEGASUS_REQT_READ	0xc0

#define	PEGASUS_REQT_WRITE	0x40

#define	PEGASUS_REQ_GET_REGS	0xf0

#define	PEGASUS_REQ_SET_REGS	0xf1

#define	PEGASUS_REQ_SET_REG	PEGASUS_REQ_SET_REGS


enum pegasus_registers {
	
EthCtrl0 = 0,
	
EthCtrl1 = 1,
	
EthCtrl2 = 2,
	
EthID = 0x10,
	
Reg1d = 0x1d,
	
EpromOffset = 0x20,
	
EpromData = 0x21,	/* 0x21 low, 0x22 high byte */
	
EpromCtrl = 0x23,
	
PhyAddr = 0x25,
	
PhyData = 0x26,		/* 0x26 low, 0x27 high byte */
	
PhyCtrl = 0x28,
	
UsbStst = 0x2a,
	
EthTxStat0 = 0x2b,
	
EthTxStat1 = 0x2c,
	
EthRxStat = 0x2d,
	
WakeupControl = 0x78,
	
Reg7b = 0x7b,
	
Gpio0 = 0x7e,
	
Gpio1 = 0x7f,
	
Reg81 = 0x81,
};



typedef struct pegasus {
	
struct usb_device	*usb;
	
struct usb_interface	*intf;
	
struct net_device	*net;
	
struct net_device_stats	stats;
	
struct mii_if_info	mii;
	
unsigned		flags;
	
unsigned		features;
	
u32			msg_enable;
	
u32			wolopts;
	
int			dev_index;
	
int			intr_interval;
	
struct tasklet_struct	rx_tl;
	
struct delayed_work	carrier_check;
	


struct urb		*rx_urb, *tx_urb, *intr_urb;
	
struct sk_buff		*rx_skb;
	
int			chip;
	
unsigned char		intr_buff[8];
	
__u8			tx_buff[PEGASUS_MTU];
	
__u8			eth_regs[4];
	
__u8			phy;
	
__u8			gpio_res;
} 
pegasus_t;



struct usb_eth_dev {
	
char	*name;
	
__u16	vendor;
	
__u16	device;
	
__u32	private; /* LSB is gpio reset value */
};


#define	VENDOR_3COM		0x0506

#define	VENDOR_ABOCOM		0x07b8

#define	VENDOR_ACCTON		0x083a

#define	VENDOR_ADMTEK		0x07a6

#define	VENDOR_AEILAB		0x3334

#define	VENDOR_ALLIEDTEL	0x07c9

#define	VENDOR_ATEN		0x0557

#define	VENDOR_BELKIN		0x050d

#define	VENDOR_BILLIONTON	0x08dd

#define	VENDOR_COMPAQ		0x049f

#define	VENDOR_COREGA		0x07aa

#define	VENDOR_DLINK		0x2001

#define	VENDOR_ELCON		0x0db7

#define	VENDOR_ELECOM		0x056e

#define	VENDOR_ELSA		0x05cc

#define	VENDOR_GIGABYTE		0x1044

#define	VENDOR_HAWKING		0x0e66

#define	VENDOR_HP		0x03f0

#define	VENDOR_IODATA		0x04bb

#define	VENDOR_KINGSTON		0x0951

#define	VENDOR_LANEED		0x056e

#define	VENDOR_LINKSYS		0x066b

#define	VENDOR_LINKSYS2		0x077b

#define	VENDOR_MELCO		0x0411

#define	VENDOR_MICROSOFT	0x045e

#define	VENDOR_MOBILITY		0x1342

#define	VENDOR_NETGEAR		0x0846

#define	VENDOR_OCT		0x0b39

#define	VENDOR_SMARTBRIDGES	0x08d1

#define	VENDOR_SMC		0x0707

#define	VENDOR_SOHOWARE		0x15e8

#define	VENDOR_SIEMENS		0x067c


#else	/* PEGASUS_DEV */

PEGASUS_DEV("3Com USB Ethernet 3C460B", VENDOR_3COM, 0x4601,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("ATEN USB Ethernet UC-110T", VENDOR_ATEN, 0x2007,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("USB HPNA/Ethernet", VENDOR_ABOCOM, 0x110c,
		DEFAULT_GPIO_RESET | PEGASUS_II | HAS_HOME_PNA)
PEGASUS_DEV("USB HPNA/Ethernet", VENDOR_ABOCOM, 0x4104,
		DEFAULT_GPIO_RESET | HAS_HOME_PNA)
PEGASUS_DEV("USB HPNA/Ethernet", VENDOR_ABOCOM, 0x4004,
		DEFAULT_GPIO_RESET | HAS_HOME_PNA)
PEGASUS_DEV("USB HPNA/Ethernet", VENDOR_ABOCOM, 0x4007,
		DEFAULT_GPIO_RESET | HAS_HOME_PNA)
PEGASUS_DEV("USB 10/100 Fast Ethernet", VENDOR_ABOCOM, 0x4102,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("USB 10/100 Fast Ethernet", VENDOR_ABOCOM, 0x4002,
		DEFAULT_GPIO_RESET)
PEGASUS_DEV("USB 10/100 Fast Ethernet", VENDOR_ABOCOM, 0x400b,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("USB 10/100 Fast Ethernet", VENDOR_ABOCOM, 0x400c,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("USB 10/100 Fast Ethernet", VENDOR_ABOCOM, 0xabc1,
		DEFAULT_GPIO_RESET)
PEGASUS_DEV("USB 10/100 Fast Ethernet", VENDOR_ABOCOM, 0x200c,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("Accton USB 10/100 Ethernet Adapter", VENDOR_ACCTON, 0x1046,
		DEFAULT_GPIO_RESET)
PEGASUS_DEV("SpeedStream USB 10/100 Ethernet", VENDOR_ACCTON, 0x5046,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("Philips USB 10/100 Ethernet", VENDOR_ACCTON, 0xb004,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("ADMtek ADM8511 \"Pegasus II\" USB Ethernet",
		VENDOR_ADMTEK, 0x8511,
		DEFAULT_GPIO_RESET | PEGASUS_II | HAS_HOME_PNA)
PEGASUS_DEV("ADMtek ADM8513 \"Pegasus II\" USB Ethernet",
		VENDOR_ADMTEK, 0x8513,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("ADMtek ADM8515 \"Pegasus II\" USB-2.0 Ethernet",
		VENDOR_ADMTEK, 0x8515,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("ADMtek AN986 \"Pegasus\" USB Ethernet (evaluation board)",
		VENDOR_ADMTEK, 0x0986,
		DEFAULT_GPIO_RESET | HAS_HOME_PNA)
PEGASUS_DEV("AN986A USB MAC", VENDOR_ADMTEK, 1986,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("AEI USB Fast Ethernet Adapter", VENDOR_AEILAB, 0x1701,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("Allied Telesyn Int. AT-USB100", VENDOR_ALLIEDTEL, 0xb100,
		DEFAULT_GPIO_RESET | PEGASUS_II)
/*
 * Distinguish between this Belkin adaptor and the Belkin bluetooth adaptors
 * with the same product IDs by checking the device class too.
 */
PEGASUS_DEV_CLASS("Belkin F5D5050 USB Ethernet", VENDOR_BELKIN, 0x0121, 0x00,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("Belkin F5U122 10/100 USB Ethernet", VENDOR_BELKIN, 0x0122,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("Billionton USB-100", VENDOR_BILLIONTON, 0x0986,
		DEFAULT_GPIO_RESET)
PEGASUS_DEV("Billionton USBLP-100", VENDOR_BILLIONTON, 0x0987,
		DEFAULT_GPIO_RESET | HAS_HOME_PNA)
PEGASUS_DEV("iPAQ Networking 10/100 USB", VENDOR_COMPAQ, 0x8511,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("Billionton USBEL-100", VENDOR_BILLIONTON, 0x0988,
		DEFAULT_GPIO_RESET)
PEGASUS_DEV("Billionton USBE-100", VENDOR_BILLIONTON, 0x8511,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("Corega FEther USB-TX", VENDOR_COREGA, 0x0004,
		DEFAULT_GPIO_RESET)
PEGASUS_DEV("Corega FEther USB-TXS", VENDOR_COREGA, 0x000d,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("D-Link DSB-650TX", VENDOR_DLINK, 0x4001,
		DEFAULT_GPIO_RESET)
PEGASUS_DEV("D-Link DSB-650TX", VENDOR_DLINK, 0x4002,
		DEFAULT_GPIO_RESET)
PEGASUS_DEV("D-Link DSB-650TX", VENDOR_DLINK, 0x4102,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("D-Link DSB-650TX", VENDOR_DLINK, 0x400b,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("D-Link DSB-650TX", VENDOR_DLINK, 0x200c,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("D-Link DSB-650TX(PNA)", VENDOR_DLINK, 0x4003,
		DEFAULT_GPIO_RESET | HAS_HOME_PNA)
PEGASUS_DEV("D-Link DSB-650", VENDOR_DLINK, 0xabc1,
		DEFAULT_GPIO_RESET)
PEGASUS_DEV("GOLDPFEIL USB Adapter", VENDOR_ELCON, 0x0002,
		DEFAULT_GPIO_RESET | PEGASUS_II | HAS_HOME_PNA)
PEGASUS_DEV("ELECOM USB Ethernet LD-USB20", VENDOR_ELECOM,  0x4010,
		DEFAULT_GPIO_RESET  | PEGASUS_II)
PEGASUS_DEV("EasiDock Ethernet", VENDOR_MOBILITY, 0x0304,
		DEFAULT_GPIO_RESET)
PEGASUS_DEV("Elsa Micolink USB2Ethernet", VENDOR_ELSA, 0x3000,
		DEFAULT_GPIO_RESET)
PEGASUS_DEV("GIGABYTE GN-BR402W Wireless Router", VENDOR_GIGABYTE, 0x8002,
		DEFAULT_GPIO_RESET)
PEGASUS_DEV("Hawking UF100 10/100 Ethernet", VENDOR_HAWKING, 0x400c,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("HP hn210c Ethernet USB", VENDOR_HP, 0x811c,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("IO DATA USB ET/TX", VENDOR_IODATA, 0x0904,
		DEFAULT_GPIO_RESET)
PEGASUS_DEV("IO DATA USB ET/TX-S", VENDOR_IODATA, 0x0913,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("IO DATA USB ETX-US2", VENDOR_IODATA, 0x093a,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("Kingston KNU101TX Ethernet", VENDOR_KINGSTON, 0x000a,
		DEFAULT_GPIO_RESET)
PEGASUS_DEV("LANEED USB Ethernet LD-USB/TX", VENDOR_LANEED, 0x4002,
		DEFAULT_GPIO_RESET)
PEGASUS_DEV("LANEED USB Ethernet LD-USBL/TX", VENDOR_LANEED, 0x4005,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("LANEED USB Ethernet LD-USB/TX", VENDOR_LANEED, 0x400b,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("LANEED USB Ethernet LD-USB/T", VENDOR_LANEED, 0xabc1,
		DEFAULT_GPIO_RESET)
PEGASUS_DEV("LANEED USB Ethernet LD-USB/TX", VENDOR_LANEED, 0x200c,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("Linksys USB10TX", VENDOR_LINKSYS, 0x2202,
		DEFAULT_GPIO_RESET)
PEGASUS_DEV("Linksys USB100TX", VENDOR_LINKSYS, 0x2203,
		DEFAULT_GPIO_RESET)
PEGASUS_DEV("Linksys USB100TX", VENDOR_LINKSYS, 0x2204,
		DEFAULT_GPIO_RESET | HAS_HOME_PNA)
PEGASUS_DEV("Linksys USB10T Ethernet Adapter", VENDOR_LINKSYS, 0x2206,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("Linksys USBVPN1", VENDOR_LINKSYS2, 0x08b4,
		DEFAULT_GPIO_RESET)
PEGASUS_DEV("Linksys USB USB100TX", VENDOR_LINKSYS, 0x400b,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("Linksys USB10TX", VENDOR_LINKSYS, 0x200c,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("MELCO/BUFFALO LUA-TX", VENDOR_MELCO, 0x0001,
		DEFAULT_GPIO_RESET)
PEGASUS_DEV("MELCO/BUFFALO LUA-TX", VENDOR_MELCO, 0x0005,
		DEFAULT_GPIO_RESET)
PEGASUS_DEV("MELCO/BUFFALO LUA2-TX", VENDOR_MELCO, 0x0009,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("Microsoft MN-110", VENDOR_MICROSOFT, 0x007a,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("NETGEAR FA101", VENDOR_NETGEAR, 0x1020,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("OCT Inc.", VENDOR_OCT, 0x0109,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("OCT USB TO Ethernet", VENDOR_OCT, 0x0901,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("smartNIC 2 PnP Adapter", VENDOR_SMARTBRIDGES, 0x0003,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("SMC 202 USB Ethernet", VENDOR_SMC, 0x0200,
		DEFAULT_GPIO_RESET)
PEGASUS_DEV("SMC 2206 USB Ethernet", VENDOR_SMC, 0x0201,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("SOHOware NUB100 Ethernet", VENDOR_SOHOWARE, 0x9100,
		DEFAULT_GPIO_RESET)
PEGASUS_DEV("SOHOware NUB110 Ethernet", VENDOR_SOHOWARE, 0x9110,
		DEFAULT_GPIO_RESET | PEGASUS_II)
PEGASUS_DEV("SpeedStream USB 10/100 Ethernet", VENDOR_SIEMENS, 0x1001,
		DEFAULT_GPIO_RESET | PEGASUS_II)


#endif	/* PEGASUS_DEV */

Overall Contributors

PersonTokensPropCommitsCommitProp
Linus Torvalds (pre-git)55745.28%12.63%
Linus Torvalds29824.23%513.16%
Petko Manolov26821.79%2052.63%
Malte Doersam252.03%12.63%
Greg Kroah-Hartman151.22%12.63%
Nobuhiro Iwamatsu141.14%12.63%
Jan Spitalnik141.14%12.63%
Mordechai Ovits141.14%12.63%
Hideaki Yoshifuji / 吉藤英明120.98%25.26%
David Brownell60.49%12.63%
Chris Rankin40.33%12.63%
Dan J Williams10.08%12.63%
Tadashi Abe10.08%12.63%
David Howells10.08%12.63%
Total1230100.00%38100.00%
Directory: drivers/net/usb
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.
Created with cregit.