cregit-Linux how code gets into the kernel

Release 4.11 drivers/spi/spi-omap-uwire.c

Directory: drivers/spi
/*
 * MicroWire interface driver for OMAP
 *
 * Copyright 2003 MontaVista Software Inc. <source@mvista.com>
 *
 * Ported to 2.6 OMAP uwire interface.
 * Copyright (C) 2004 Texas Instruments.
 *
 * Generalization patches by Juha Yrjola <juha.yrjola@nokia.com>
 *
 * Copyright (C) 2005 David Brownell (ported to 2.6 SPI interface)
 * Copyright (C) 2006 Nokia
 *
 * Many updates by Imre Deak <imre.deak@nokia.com>
 *
 * This program is free software; you can redistribute it and/or modify it
 * under the terms of the GNU General Public License as published by the
 * Free Software Foundation; either version 2 of the License, or (at your
 * option) any later version.
 *
 * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED
 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
 * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
 * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
 * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 */
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/platform_device.h>
#include <linux/interrupt.h>
#include <linux/err.h>
#include <linux/clk.h>
#include <linux/slab.h>
#include <linux/device.h>

#include <linux/spi/spi.h>
#include <linux/spi/spi_bitbang.h>
#include <linux/module.h>
#include <linux/io.h>

#include <mach/hardware.h>
#include <asm/mach-types.h>

#include <mach/mux.h>

#include <mach/omap7xx.h>	/* OMAP7XX_IO_CONF registers */


/* FIXME address is now a platform device resource,
 * and irqs should show there too...
 */

#define UWIRE_BASE_PHYS		0xFFFB3000

/* uWire Registers: */

#define UWIRE_IO_SIZE 0x20

#define UWIRE_TDR     0x00

#define UWIRE_RDR     0x00

#define UWIRE_CSR     0x01

#define UWIRE_SR1     0x02

#define UWIRE_SR2     0x03

#define UWIRE_SR3     0x04

#define UWIRE_SR4     0x05

#define UWIRE_SR5     0x06

/* CSR bits */

#define	RDRB	(1 << 15)

#define	CSRB	(1 << 14)

#define	START	(1 << 13)

#define	CS_CMD	(1 << 12)

/* SR1 or SR2 bits */

#define UWIRE_READ_FALLING_EDGE		0x0001

#define UWIRE_READ_RISING_EDGE		0x0000

#define UWIRE_WRITE_FALLING_EDGE	0x0000

#define UWIRE_WRITE_RISING_EDGE		0x0002

#define UWIRE_CS_ACTIVE_LOW		0x0000

#define UWIRE_CS_ACTIVE_HIGH		0x0004

#define UWIRE_FREQ_DIV_2		0x0000

#define UWIRE_FREQ_DIV_4		0x0008

#define UWIRE_FREQ_DIV_8		0x0010

#define UWIRE_CHK_READY			0x0020

#define UWIRE_CLK_INVERTED		0x0040



struct uwire_spi {
	
struct spi_bitbang	bitbang;
	
struct clk		*ck;
};


struct uwire_state {
	
unsigned	div1_idx;
};

/* REVISIT compile time constant for idx_shift? */
/*
 * Or, put it in a structure which is used throughout the driver;
 * that avoids having to issue two loads for each bit of static data.
 */

static unsigned int uwire_idx_shift;

static void __iomem *uwire_base;


static inline void uwire_write_reg(int idx, u16 val) { __raw_writew(val, uwire_base + (idx << uwire_idx_shift)); }

Contributors

PersonTokensPropCommitsCommitProp
David Brownell2596.15%150.00%
Russell King13.85%150.00%
Total26100.00%2100.00%


static inline u16 uwire_read_reg(int idx) { return __raw_readw(uwire_base + (idx << uwire_idx_shift)); }

Contributors

PersonTokensPropCommitsCommitProp
David Brownell2195.45%150.00%
Russell King14.55%150.00%
Total22100.00%2100.00%


static inline void omap_uwire_configure_mode(u8 cs, unsigned long flags) { u16 w, val = 0; int shift, reg; if (flags & UWIRE_CLK_INVERTED) val ^= 0x03; val = flags & 0x3f; if (cs & 1) shift = 6; else shift = 0; if (cs <= 1) reg = UWIRE_SR1; else reg = UWIRE_SR2; w = uwire_read_reg(reg); w &= ~(0x3f << shift); w |= val << shift; uwire_write_reg(reg, w); }

Contributors

PersonTokensPropCommitsCommitProp
David Brownell101100.00%1100.00%
Total101100.00%1100.00%


static int wait_uwire_csr_flag(u16 mask, u16 val, int might_not_catch) { u16 w; int c = 0; unsigned long max_jiffies = jiffies + HZ; for (;;) { w = uwire_read_reg(UWIRE_CSR); if ((w & mask) == val) break; if (time_after(jiffies, max_jiffies)) { printk(KERN_ERR "%s: timeout. reg=%#06x " "mask=%#06x val=%#06x\n", __func__, w, mask, val); return -1; } c++; if (might_not_catch && c > 64) break; } return 0; }

Contributors

PersonTokensPropCommitsCommitProp
David Brownell10099.01%150.00%
Harvey Harrison10.99%150.00%
Total101100.00%2100.00%


static void uwire_set_clk1_div(int div1_idx) { u16 w; w = uwire_read_reg(UWIRE_SR3); w &= ~(0x03 << 1); w |= div1_idx << 1; uwire_write_reg(UWIRE_SR3, w); }

Contributors

PersonTokensPropCommitsCommitProp
David Brownell41100.00%1100.00%
Total41100.00%1100.00%


static void uwire_chipselect(struct spi_device *spi, int value) { struct uwire_state *ust = spi->controller_state; u16 w; int old_cs; BUG_ON(wait_uwire_csr_flag(CSRB, 0, 0)); w = uwire_read_reg(UWIRE_CSR); old_cs = (w >> 10) & 0x03; if (value == BITBANG_CS_INACTIVE || old_cs != spi->chip_select) { /* Deselect this CS, or the previous CS */ w &= ~CS_CMD; uwire_write_reg(UWIRE_CSR, w); } /* activate specfied chipselect */ if (value == BITBANG_CS_ACTIVE) { uwire_set_clk1_div(ust->div1_idx); /* invert clock? */ if (spi->mode & SPI_CPOL) uwire_write_reg(UWIRE_SR4, 1); else uwire_write_reg(UWIRE_SR4, 0); w = spi->chip_select << 10; w |= CS_CMD; uwire_write_reg(UWIRE_CSR, w); } }

Contributors

PersonTokensPropCommitsCommitProp
David Brownell144100.00%1100.00%
Total144100.00%1100.00%


static int uwire_txrx(struct spi_device *spi, struct spi_transfer *t) { unsigned len = t->len; unsigned bits = t->bits_per_word; unsigned bytes; u16 val, w; int status = 0; if (!t->tx_buf && !t->rx_buf) return 0; w = spi->chip_select << 10; w |= CS_CMD; if (t->tx_buf) { const u8 *buf = t->tx_buf; /* NOTE: DMA could be used for TX transfers */ /* write one or two bytes at a time */ while (len >= 1) { /* tx bit 15 is first sent; we byteswap multibyte words * (msb-first) on the way out from memory. */ val = *buf++; if (bits > 8) { bytes = 2; val |= *buf++ << 8; } else bytes = 1; val <<= 16 - bits; #ifdef VERBOSE pr_debug("%s: write-%d =%04x\n", dev_name(&spi->dev), bits, val); #endif if (wait_uwire_csr_flag(CSRB, 0, 0)) goto eio; uwire_write_reg(UWIRE_TDR, val); /* start write */ val = START | w | (bits << 5); uwire_write_reg(UWIRE_CSR, val); len -= bytes; /* Wait till write actually starts. * This is needed with MPU clock 60+ MHz. * REVISIT: we may not have time to catch it... */ if (wait_uwire_csr_flag(CSRB, CSRB, 1)) goto eio; status += bytes; } /* REVISIT: save this for later to get more i/o overlap */ if (wait_uwire_csr_flag(CSRB, 0, 0)) goto eio; } else if (t->rx_buf) { u8 *buf = t->rx_buf; /* read one or two bytes at a time */ while (len) { if (bits > 8) { bytes = 2; } else bytes = 1; /* start read */ val = START | w | (bits << 0); uwire_write_reg(UWIRE_CSR, val); len -= bytes; /* Wait till read actually starts */ (void) wait_uwire_csr_flag(CSRB, CSRB, 1); if (wait_uwire_csr_flag(RDRB | CSRB, RDRB, 0)) goto eio; /* rx bit 0 is last received; multibyte words will * be properly byteswapped on the way to memory. */ val = uwire_read_reg(UWIRE_RDR); val &= (1 << bits) - 1; *buf++ = (u8) val; if (bytes == 2) *buf++ = val >> 8; status += bytes; #ifdef VERBOSE pr_debug("%s: read-%d =%04x\n", dev_name(&spi->dev), bits, val); #endif } } return status; eio: return -EIO; }

Contributors

PersonTokensPropCommitsCommitProp
David Brownell39597.29%133.33%
Kay Sievers81.97%133.33%
Axel Lin30.74%133.33%
Total406100.00%3100.00%


static int uwire_setup_transfer(struct spi_device *spi, struct spi_transfer *t) { struct uwire_state *ust = spi->controller_state; struct uwire_spi *uwire; unsigned flags = 0; unsigned hz; unsigned long rate; int div1_idx; int div1; int div2; int status; uwire = spi_master_get_devdata(spi->master); /* mode 0..3, clock inverted separately; * standard nCS signaling; * don't treat DI=high as "not ready" */ if (spi->mode & SPI_CS_HIGH) flags |= UWIRE_CS_ACTIVE_HIGH; if (spi->mode & SPI_CPOL) flags |= UWIRE_CLK_INVERTED; switch (spi->mode & (SPI_CPOL | SPI_CPHA)) { case SPI_MODE_0: case SPI_MODE_3: flags |= UWIRE_WRITE_FALLING_EDGE | UWIRE_READ_RISING_EDGE; break; case SPI_MODE_1: case SPI_MODE_2: flags |= UWIRE_WRITE_RISING_EDGE | UWIRE_READ_FALLING_EDGE; break; } /* assume it's already enabled */ rate = clk_get_rate(uwire->ck); if (t != NULL) hz = t->speed_hz; else hz = spi->max_speed_hz; if (!hz) { pr_debug("%s: zero speed?\n", dev_name(&spi->dev)); status = -EINVAL; goto done; } /* F_INT = mpu_xor_clk / DIV1 */ for (div1_idx = 0; div1_idx < 4; div1_idx++) { switch (div1_idx) { case 0: div1 = 2; break; case 1: div1 = 4; break; case 2: div1 = 7; break; default: case 3: div1 = 10; break; } div2 = (rate / div1 + hz - 1) / hz; if (div2 <= 8) break; } if (div1_idx == 4) { pr_debug("%s: lowest clock %ld, need %d\n", dev_name(&spi->dev), rate / 10 / 8, hz); status = -EDOM; goto done; } /* we have to cache this and reset in uwire_chipselect as this is a * global parameter and another uwire device can change it under * us */ ust->div1_idx = div1_idx; uwire_set_clk1_div(div1_idx); rate /= div1; switch (div2) { case 0: case 1: case 2: flags |= UWIRE_FREQ_DIV_2; rate /= 2; break; case 3: case 4: flags |= UWIRE_FREQ_DIV_4; rate /= 4; break; case 5: case 6: case 7: case 8: flags |= UWIRE_FREQ_DIV_8; rate /= 8; break; } omap_uwire_configure_mode(spi->chip_select, flags); pr_debug("%s: uwire flags %02x, armxor %lu KHz, SCK %lu KHz\n", __func__, flags, clk_get_rate(uwire->ck) / 1000, rate / 1000); status = 0; done: return status; }

Contributors

PersonTokensPropCommitsCommitProp
David Brownell39495.17%120.00%
Kay Sievers81.93%120.00%
Jarkko Nikula71.69%120.00%
Imre Deak40.97%120.00%
Harvey Harrison10.24%120.00%
Total414100.00%5100.00%


static int uwire_setup(struct spi_device *spi) { struct uwire_state *ust = spi->controller_state; if (ust == NULL) { ust = kzalloc(sizeof(*ust), GFP_KERNEL); if (ust == NULL) return -ENOMEM; spi->controller_state = ust; } return uwire_setup_transfer(spi, NULL); }

Contributors

PersonTokensPropCommitsCommitProp
David Brownell65100.00%1100.00%
Total65100.00%1100.00%


static void uwire_cleanup(struct spi_device *spi) { kfree(spi->controller_state); }

Contributors

PersonTokensPropCommitsCommitProp
David Brownell18100.00%1100.00%
Total18100.00%1100.00%


static void uwire_off(struct uwire_spi *uwire) { uwire_write_reg(UWIRE_SR3, 0); clk_disable(uwire->ck); spi_master_put(uwire->bitbang.master); }

Contributors

PersonTokensPropCommitsCommitProp
David Brownell34100.00%1100.00%
Total34100.00%1100.00%


static int uwire_probe(struct platform_device *pdev) { struct spi_master *master; struct uwire_spi *uwire; int status; master = spi_alloc_master(&pdev->dev, sizeof *uwire); if (!master) return -ENODEV; uwire = spi_master_get_devdata(master); uwire_base = devm_ioremap(&pdev->dev, UWIRE_BASE_PHYS, UWIRE_IO_SIZE); if (!uwire_base) { dev_dbg(&pdev->dev, "can't ioremap UWIRE\n"); spi_master_put(master); return -ENOMEM; } platform_set_drvdata(pdev, uwire); uwire->ck = devm_clk_get(&pdev->dev, "fck"); if (IS_ERR(uwire->ck)) { status = PTR_ERR(uwire->ck); dev_dbg(&pdev->dev, "no functional clock?\n"); spi_master_put(master); return status; } clk_enable(uwire->ck); if (cpu_is_omap7xx()) uwire_idx_shift = 1; else uwire_idx_shift = 2; uwire_write_reg(UWIRE_SR3, 1); /* the spi->mode bits understood by this driver: */ master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH; master->bits_per_word_mask = SPI_BPW_RANGE_MASK(1, 16); master->flags = SPI_MASTER_HALF_DUPLEX; master->bus_num = 2; /* "official" */ master->num_chipselect = 4; master->setup = uwire_setup; master->cleanup = uwire_cleanup; uwire->bitbang.master = master; uwire->bitbang.chipselect = uwire_chipselect; uwire->bitbang.setup_transfer = uwire_setup_transfer; uwire->bitbang.txrx_bufs = uwire_txrx; status = spi_bitbang_start(&uwire->bitbang); if (status < 0) { uwire_off(uwire); } return status; }

Contributors

PersonTokensPropCommitsCommitProp
David Brownell22476.71%333.33%
Russell King4816.44%222.22%
Axel Lin113.77%111.11%
Himangi Saraogi72.40%111.11%
Jingoo Han10.34%111.11%
Alistair Buxton10.34%111.11%
Total292100.00%9100.00%


static int uwire_remove(struct platform_device *pdev) { struct uwire_spi *uwire = platform_get_drvdata(pdev); // FIXME remove all child devices, somewhere ... spi_bitbang_stop(&uwire->bitbang); uwire_off(uwire); return 0; }

Contributors

PersonTokensPropCommitsCommitProp
David Brownell3694.74%133.33%
Axel Lin12.63%133.33%
Jingoo Han12.63%133.33%
Total38100.00%3100.00%

/* work with hotplug and coldplug */ MODULE_ALIAS("platform:omap_uwire"); static struct platform_driver uwire_driver = { .driver = { .name = "omap_uwire", }, .probe = uwire_probe, .remove = uwire_remove, // suspend ... unuse ck // resume ... use ck };
static int __init omap_uwire_init(void) { /* FIXME move these into the relevant board init code. also, include * H3 support; it uses tsc2101 like H2 (on a different chipselect). */ if (machine_is_omap_h2()) { /* defaults: W21 SDO, U18 SDI, V19 SCL */ omap_cfg_reg(N14_1610_UWIRE_CS0); omap_cfg_reg(N15_1610_UWIRE_CS1); } if (machine_is_omap_perseus2()) { /* configure pins: MPU_UW_nSCS1, MPU_UW_SDO, MPU_UW_SCLK */ int val = omap_readl(OMAP7XX_IO_CONF_9) & ~0x00EEE000; omap_writel(val | 0x00AAA000, OMAP7XX_IO_CONF_9); } return platform_driver_register(&uwire_driver); }

Contributors

PersonTokensPropCommitsCommitProp
David Brownell6095.24%133.33%
Alistair Buxton23.17%133.33%
Wolfram Sang11.59%133.33%
Total63100.00%3100.00%


static void __exit omap_uwire_exit(void) { platform_driver_unregister(&uwire_driver); }

Contributors

PersonTokensPropCommitsCommitProp
David Brownell15100.00%1100.00%
Total15100.00%1100.00%

subsys_initcall(omap_uwire_init); module_exit(omap_uwire_exit); MODULE_LICENSE("GPL");

Overall Contributors

PersonTokensPropCommitsCommitProp
David Brownell188393.08%313.04%
Russell King572.82%28.70%
Kay Sievers221.09%28.70%
Axel Lin150.74%28.70%
Jarkko Nikula80.40%28.70%
Himangi Saraogi70.35%14.35%
Wolfram Sang60.30%14.35%
Alistair Buxton40.20%14.35%
Imre Deak40.20%14.35%
Paul Gortmaker30.15%14.35%
Tejun Heo30.15%14.35%
Mark Brown30.15%14.35%
Tony Lindgren20.10%28.70%
Jingoo Han20.10%14.35%
Sachin Kamat20.10%14.35%
Harvey Harrison20.10%14.35%
Total2023100.00%23100.00%
Directory: drivers/spi
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.
Created with cregit.