/* * m32r_sio_reg.h * * Copyright (C) 1992, 1994 by Theodore Ts'o. * Copyright (C) 2004 Hirokazu Takata <takata at linux-m32r.org> * * Redistribution of this file is permitted under the terms of the GNU * Public License (GPL) * * These are the UART port assignments, expressed as offsets from the base * register. These assignments should hold for any serial port based on * a 8250, 16450, or 16550(A). */ #ifndef _M32R_SIO_REG_H #define _M32R_SIO_REG_H #ifdef CONFIG_SERIAL_M32R_PLDSIO #define SIOCR 0x000 #define SIOMOD0 0x002 #define SIOMOD1 0x004 #define SIOSTS 0x006 #define SIOTRCR 0x008 #define SIOBAUR 0x00a // #define SIORBAUR 0x018 #define SIOTXB 0x00c #define SIORXB 0x00e #define UART_RX ((unsigned long) PLD_ESIO0RXB) /* In: Receive buffer (DLAB=0) */ #define UART_TX ((unsigned long) PLD_ESIO0TXB) /* Out: Transmit buffer (DLAB=0) */ #define UART_DLL 0 /* Out: Divisor Latch Low (DLAB=1) */ #define UART_TRG 0 /* (LCR=BF) FCTR bit 7 selects Rx or Tx * In: Fifo count * Out: Fifo custom trigger levels * XR16C85x only */ #define UART_DLM 0 /* Out: Divisor Latch High (DLAB=1) */ #define UART_IER ((unsigned long) PLD_ESIO0INTCR) /* Out: Interrupt Enable Register */ #define UART_FCTR 0 /* (LCR=BF) Feature Control Register * XR16C85x only */ #define UART_IIR 0 /* In: Interrupt ID Register */ #define UART_FCR 0 /* Out: FIFO Control Register */ #define UART_EFR 0 /* I/O: Extended Features Register */ /* (DLAB=1, 16C660 only) */ #define UART_LCR 0 /* Out: Line Control Register */ #define UART_MCR 0 /* Out: Modem Control Register */ #define UART_LSR ((unsigned long) PLD_ESIO0STS) /* In: Line Status Register */ #define UART_MSR 0 /* In: Modem Status Register */ #define UART_SCR 0 /* I/O: Scratch Register */ #define UART_EMSR 0 /* (LCR=BF) Extended Mode Select Register * FCTR bit 6 selects SCR or EMSR * XR16c85x only */ #else /* not CONFIG_SERIAL_M32R_PLDSIO */ #define SIOCR 0x000 #define SIOMOD0 0x004 #define SIOMOD1 0x008 #define SIOSTS 0x00c #define SIOTRCR 0x010 #define SIOBAUR 0x014 #define SIORBAUR 0x018 #define SIOTXB 0x01c #define SIORXB 0x020 #define UART_RX M32R_SIO0_RXB_PORTL /* In: Receive buffer (DLAB=0) */ #define UART_TX M32R_SIO0_TXB_PORTL /* Out: Transmit buffer (DLAB=0) */ #define UART_DLL 0 /* Out: Divisor Latch Low (DLAB=1) */ #define UART_TRG 0 /* (LCR=BF) FCTR bit 7 selects Rx or Tx * In: Fifo count * Out: Fifo custom trigger levels * XR16C85x only */ #define UART_DLM 0 /* Out: Divisor Latch High (DLAB=1) */ #define UART_IER M32R_SIO0_TRCR_PORTL /* Out: Interrupt Enable Register */ #define UART_FCTR 0 /* (LCR=BF) Feature Control Register * XR16C85x only */ #define UART_IIR 0 /* In: Interrupt ID Register */ #define UART_FCR 0 /* Out: FIFO Control Register */ #define UART_EFR 0 /* I/O: Extended Features Register */ /* (DLAB=1, 16C660 only) */ #define UART_LCR 0 /* Out: Line Control Register */ #define UART_MCR 0 /* Out: Modem Control Register */ #define UART_LSR M32R_SIO0_STS_PORTL /* In: Line Status Register */ #define UART_MSR 0 /* In: Modem Status Register */ #define UART_SCR 0 /* I/O: Scratch Register */ #define UART_EMSR 0 /* (LCR=BF) Extended Mode Select Register * FCTR bit 6 selects SCR or EMSR * XR16c85x only */ #endif /* CONFIG_SERIAL_M32R_PLDSIO */ #define UART_EMPTY (UART_LSR_TEMT | UART_LSR_THRE) /* * These are the definitions for the Line Control Register * * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits. */ #define UART_LCR_DLAB 0x80 /* Divisor latch access bit */ #define UART_LCR_SBC 0x40 /* Set break control */ #define UART_LCR_SPAR 0x20 /* Stick parity (?) */ #define UART_LCR_EPAR 0x10 /* Even parity select */ #define UART_LCR_PARITY 0x08 /* Parity Enable */ #define UART_LCR_STOP 0x04 /* Stop bits: 0=1 stop bit, 1= 2 stop bits */ #define UART_LCR_WLEN5 0x00 /* Wordlength: 5 bits */ #define UART_LCR_WLEN6 0x01 /* Wordlength: 6 bits */ #define UART_LCR_WLEN7 0x02 /* Wordlength: 7 bits */ #define UART_LCR_WLEN8 0x03 /* Wordlength: 8 bits */ /* * These are the definitions for the Line Status Register */ #define UART_LSR_TEMT 0x02 /* Transmitter empty */ #define UART_LSR_THRE 0x01 /* Transmit-hold-register empty */ #define UART_LSR_BI 0x00 /* Break interrupt indicator */ #define UART_LSR_FE 0x80 /* Frame error indicator */ #define UART_LSR_PE 0x40 /* Parity error indicator */ #define UART_LSR_OE 0x20 /* Overrun error indicator */ #define UART_LSR_DR 0x04 /* Receiver data ready */ /* * These are the definitions for the Interrupt Identification Register */ #define UART_IIR_NO_INT 0x01 /* No interrupts pending */ #define UART_IIR_ID 0x06 /* Mask for the interrupt ID */ #define UART_IIR_MSI 0x00 /* Modem status interrupt */ #define UART_IIR_THRI 0x02 /* Transmitter holding register empty */ #define UART_IIR_RDI 0x04 /* Receiver data interrupt */ #define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */ /* * These are the definitions for the Interrupt Enable Register */ #define UART_IER_MSI 0x00 /* Enable Modem status interrupt */ #define UART_IER_RLSI 0x08 /* Enable receiver line status interrupt */ #define UART_IER_THRI 0x03 /* Enable Transmitter holding register int. */ #define UART_IER_RDI 0x04 /* Enable receiver data interrupt */ #endif /* _M32R_SIO_REG_H */Overall Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| Hirokazu Takata | 393 | 100.00% | 1 | 100.00% |
| Total | 393 | 100.00% | 1 | 100.00% |