Release 4.12 drivers/mfd/cros_ec_spi.c
  
  
  
/*
 * ChromeOS EC multi-function device (SPI)
 *
 * Copyright (C) 2012 Google, Inc
 *
 * This software is licensed under the terms of the GNU General Public
 * License version 2, as published by the Free Software Foundation, and
 * may be copied, distributed, and modified under those terms.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 */
#include <linux/delay.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/mfd/cros_ec.h>
#include <linux/mfd/cros_ec_commands.h>
#include <linux/of.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
#include <linux/spi/spi.h>
/* The header byte, which follows the preamble */
#define EC_MSG_HEADER			0xec
/*
 * Number of EC preamble bytes we read at a time. Since it takes
 * about 400-500us for the EC to respond there is not a lot of
 * point in tuning this. If the EC could respond faster then
 * we could increase this so that might expect the preamble and
 * message to occur in a single transaction. However, the maximum
 * SPI transfer size is 256 bytes, so at 5MHz we need a response
 * time of perhaps <320us (200 bytes / 1600 bits).
 */
#define EC_MSG_PREAMBLE_COUNT		32
/*
 * Allow for a long time for the EC to respond.  We support i2c
 * tunneling and support fairly long messages for the tunnel (249
 * bytes long at the moment).  If we're talking to a 100 kHz device
 * on the other end and need to transfer ~256 bytes, then we need:
 *  10 us/bit * ~10 bits/byte * ~256 bytes = ~25ms
 *
 * We'll wait 8 times that to handle clock stretching and other
 * paranoia.  Note that some battery gas gauge ICs claim to have a
 * clock stretch of 144ms in rare situations.  That's incentive for
 * not directly passing i2c through, but it's too late for that for
 * existing hardware.
 *
 * It's pretty unlikely that we'll really see a 249 byte tunnel in
 * anything other than testing.  If this was more common we might
 * consider having slow commands like this require a GET_STATUS
 * wait loop.  The 'flash write' command would be another candidate
 * for this, clocking in at 2-3ms.
 */
#define EC_MSG_DEADLINE_MS		200
/*
  * Time between raising the SPI chip select (for the end of a
  * transaction) and dropping it again (for the next transaction).
  * If we go too fast, the EC will miss the transaction. We know that we
  * need at least 70 us with the 16 MHz STM32 EC, so go with 200 us to be
  * safe.
  */
#define EC_SPI_RECOVERY_TIME_NS	(200 * 1000)
/**
 * struct cros_ec_spi - information about a SPI-connected EC
 *
 * @spi: SPI device we are connected to
 * @last_transfer_ns: time that we last finished a transfer, or 0 if there
 *      if no record
 * @start_of_msg_delay: used to set the delay_usecs on the spi_transfer that
 *      is sent when we want to turn on CS at the start of a transaction.
 * @end_of_msg_delay: used to set the delay_usecs on the spi_transfer that
 *      is sent when we want to turn off CS at the end of a transaction.
 */
struct cros_ec_spi {
	
struct spi_device *spi;
	
s64 last_transfer_ns;
	
unsigned int start_of_msg_delay;
	
unsigned int end_of_msg_delay;
};
static void debug_packet(struct device *dev, const char *name, u8 *ptr,
			 int len)
{
#ifdef DEBUG
	int i;
	dev_dbg(dev, "%s: ", name);
	for (i = 0; i < len; i++)
		pr_cont(" %02x", ptr[i]);
	pr_cont("\n");
#endif
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp | 
| Simon Glass | 62 | 91.18% | 1 | 50.00% | 
| Thierry Reding | 6 | 8.82% | 1 | 50.00% | 
| Total | 68 | 100.00% | 2 | 100.00% | 
static int terminate_request(struct cros_ec_device *ec_dev)
{
	struct cros_ec_spi *ec_spi = ec_dev->priv;
	struct spi_message msg;
	struct spi_transfer trans;
	int ret;
	/*
         * Turn off CS, possibly adding a delay to ensure the rising edge
         * doesn't come too soon after the end of the data.
         */
	spi_message_init(&msg);
	memset(&trans, 0, sizeof(trans));
	trans.delay_usecs = ec_spi->end_of_msg_delay;
	spi_message_add_tail(&trans, &msg);
	ret = spi_sync_locked(ec_spi->spi, &msg);
	/* Reset end-of-response timer */
	ec_spi->last_transfer_ns = ktime_get_ns();
	if (ret < 0) {
		dev_err(ec_dev->dev,
			"cs-deassert spi transfer failed: %d\n",
			ret);
	}
	return ret;
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp | 
| Stephen Barber | 109 | 99.09% | 1 | 50.00% | 
| Nicolas Boichat | 1 | 0.91% | 1 | 50.00% | 
| Total | 110 | 100.00% | 2 | 100.00% | 
/**
 * receive_n_bytes - receive n bytes from the EC.
 *
 * Assumes buf is a pointer into the ec_dev->din buffer
 */
static int receive_n_bytes(struct cros_ec_device *ec_dev, u8 *buf, int n)
{
	struct cros_ec_spi *ec_spi = ec_dev->priv;
	struct spi_transfer trans;
	struct spi_message msg;
	int ret;
	BUG_ON(buf - ec_dev->din + n > ec_dev->din_size);
	memset(&trans, 0, sizeof(trans));
	trans.cs_change = 1;
	trans.rx_buf = buf;
	trans.len = n;
	spi_message_init(&msg);
	spi_message_add_tail(&trans, &msg);
	ret = spi_sync_locked(ec_spi->spi, &msg);
	if (ret < 0)
		dev_err(ec_dev->dev, "spi transfer failed: %d\n", ret);
	return ret;
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp | 
| Simon Glass | 109 | 83.21% | 1 | 25.00% | 
| Stephen Barber | 20 | 15.27% | 1 | 25.00% | 
| Nicolas Boichat | 1 | 0.76% | 1 | 25.00% | 
| Thierry Reding | 1 | 0.76% | 1 | 25.00% | 
| Total | 131 | 100.00% | 4 | 100.00% | 
/**
 * cros_ec_spi_receive_packet - Receive a packet from the EC.
 *
 * This function has two phases: reading the preamble bytes (since if we read
 * data from the EC before it is ready to send, we just get preamble) and
 * reading the actual message.
 *
 * The received data is placed into ec_dev->din.
 *
 * @ec_dev: ChromeOS EC device
 * @need_len: Number of message bytes we need to read
 */
static int cros_ec_spi_receive_packet(struct cros_ec_device *ec_dev,
				      int need_len)
{
	struct ec_host_response *response;
	u8 *ptr, *end;
	int ret;
	unsigned long deadline;
	int todo;
	BUG_ON(ec_dev->din_size < EC_MSG_PREAMBLE_COUNT);
	/* Receive data until we see the header byte */
	deadline = jiffies + msecs_to_jiffies(EC_MSG_DEADLINE_MS);
	while (true) {
		unsigned long start_jiffies = jiffies;
		ret = receive_n_bytes(ec_dev,
				      ec_dev->din,
				      EC_MSG_PREAMBLE_COUNT);
		if (ret < 0)
			return ret;
		ptr = ec_dev->din;
		for (end = ptr + EC_MSG_PREAMBLE_COUNT; ptr != end; ptr++) {
			if (*ptr == EC_SPI_FRAME_START) {
				dev_dbg(ec_dev->dev, "msg found at %zd\n",
					ptr - ec_dev->din);
				break;
			}
		}
		if (ptr != end)
			break;
		/*
                 * Use the time at the start of the loop as a timeout.  This
                 * gives us one last shot at getting the transfer and is useful
                 * in case we got context switched out for a while.
                 */
		if (time_after(start_jiffies, deadline)) {
			dev_warn(ec_dev->dev, "EC failed to respond in time\n");
			return -ETIMEDOUT;
		}
	}
	/*
         * ptr now points to the header byte. Copy any valid data to the
         * start of our buffer
         */
	todo = end - ++ptr;
	BUG_ON(todo < 0 || todo > ec_dev->din_size);
	todo = min(todo, need_len);
	memmove(ec_dev->din, ptr, todo);
	ptr = ec_dev->din + todo;
	dev_dbg(ec_dev->dev, "need %d, got %d bytes from preamble\n",
		need_len, todo);
	need_len -= todo;
	/* If the entire response struct wasn't read, get the rest of it. */
	if (todo < sizeof(*response)) {
		ret = receive_n_bytes(ec_dev, ptr, sizeof(*response) - todo);
		if (ret < 0)
			return -EBADMSG;
		ptr += (sizeof(*response) - todo);
		todo = sizeof(*response);
	}
	response = (struct ec_host_response *)ec_dev->din;
	/* Abort if data_len is too large. */
	if (response->data_len > ec_dev->din_size)
		return -EMSGSIZE;
	/* Receive data until we have it all */
	while (need_len > 0) {
		/*
                 * We can't support transfers larger than the SPI FIFO size
                 * unless we have DMA. We don't have DMA on the ISP SPI ports
                 * for Exynos. We need a way of asking SPI driver for
                 * maximum-supported transfer size.
                 */
		todo = min(need_len, 256);
		dev_dbg(ec_dev->dev, "loop, todo=%d, need_len=%d, ptr=%zd\n",
			todo, need_len, ptr - ec_dev->din);
		ret = receive_n_bytes(ec_dev, ptr, todo);
		if (ret < 0)
			return ret;
		ptr += todo;
		need_len -= todo;
	}
	dev_dbg(ec_dev->dev, "loop done, ptr=%zd\n", ptr - ec_dev->din);
	return 0;
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp | 
| Stephen Barber | 252 | 62.22% | 1 | 20.00% | 
| Simon Glass | 145 | 35.80% | 1 | 20.00% | 
| Douglas Anderson | 5 | 1.23% | 1 | 20.00% | 
| Lee Jones | 2 | 0.49% | 1 | 20.00% | 
| Geert Uytterhoeven | 1 | 0.25% | 1 | 20.00% | 
| Total | 405 | 100.00% | 5 | 100.00% | 
/**
 * cros_ec_spi_receive_response - Receive a response from the EC.
 *
 * This function has two phases: reading the preamble bytes (since if we read
 * data from the EC before it is ready to send, we just get preamble) and
 * reading the actual message.
 *
 * The received data is placed into ec_dev->din.
 *
 * @ec_dev: ChromeOS EC device
 * @need_len: Number of message bytes we need to read
 */
static int cros_ec_spi_receive_response(struct cros_ec_device *ec_dev,
					int need_len)
{
	u8 *ptr, *end;
	int ret;
	unsigned long deadline;
	int todo;
	BUG_ON(ec_dev->din_size < EC_MSG_PREAMBLE_COUNT);
	/* Receive data until we see the header byte */
	deadline = jiffies + msecs_to_jiffies(EC_MSG_DEADLINE_MS);
	while (true) {
		unsigned long start_jiffies = jiffies;
		ret = receive_n_bytes(ec_dev,
				      ec_dev->din,
				      EC_MSG_PREAMBLE_COUNT);
		if (ret < 0)
			return ret;
		ptr = ec_dev->din;
		for (end = ptr + EC_MSG_PREAMBLE_COUNT; ptr != end; ptr++) {
			if (*ptr == EC_SPI_FRAME_START) {
				dev_dbg(ec_dev->dev, "msg found at %zd\n",
					ptr - ec_dev->din);
				break;
			}
		}
		if (ptr != end)
			break;
		/*
                 * Use the time at the start of the loop as a timeout.  This
                 * gives us one last shot at getting the transfer and is useful
                 * in case we got context switched out for a while.
                 */
		if (time_after(start_jiffies, deadline)) {
			dev_warn(ec_dev->dev, "EC failed to respond in time\n");
			return -ETIMEDOUT;
		}
	}
	/*
         * ptr now points to the header byte. Copy any valid data to the
         * start of our buffer
         */
	todo = end - ++ptr;
	BUG_ON(todo < 0 || todo > ec_dev->din_size);
	todo = min(todo, need_len);
	memmove(ec_dev->din, ptr, todo);
	ptr = ec_dev->din + todo;
	dev_dbg(ec_dev->dev, "need %d, got %d bytes from preamble\n",
		 need_len, todo);
	need_len -= todo;
	/* Receive data until we have it all */
	while (need_len > 0) {
		/*
                 * We can't support transfers larger than the SPI FIFO size
                 * unless we have DMA. We don't have DMA on the ISP SPI ports
                 * for Exynos. We need a way of asking SPI driver for
                 * maximum-supported transfer size.
                 */
		todo = min(need_len, 256);
		dev_dbg(ec_dev->dev, "loop, todo=%d, need_len=%d, ptr=%zd\n",
			todo, need_len, ptr - ec_dev->din);
		ret = receive_n_bytes(ec_dev, ptr, todo);
		if (ret < 0)
			return ret;
		debug_packet(ec_dev->dev, "interim", ptr, todo);
		ptr += todo;
		need_len -= todo;
	}
	dev_dbg(ec_dev->dev, "loop done, ptr=%zd\n", ptr - ec_dev->din);
	return 0;
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp | 
| Stephen Barber | 325 | 99.39% | 1 | 50.00% | 
| Lee Jones | 2 | 0.61% | 1 | 50.00% | 
| Total | 327 | 100.00% | 2 | 100.00% | 
/**
 * cros_ec_pkt_xfer_spi - Transfer a packet over SPI and receive the reply
 *
 * @ec_dev: ChromeOS EC device
 * @ec_msg: Message to transfer
 */
static int cros_ec_pkt_xfer_spi(struct cros_ec_device *ec_dev,
				struct cros_ec_command *ec_msg)
{
	struct ec_host_response *response;
	struct cros_ec_spi *ec_spi = ec_dev->priv;
	struct spi_transfer trans, trans_delay;
	struct spi_message msg;
	int i, len;
	u8 *ptr;
	u8 *rx_buf;
	u8 sum;
	int ret = 0, final_ret;
	len = cros_ec_prepare_tx(ec_dev, ec_msg);
	dev_dbg(ec_dev->dev, "prepared, len=%d\n", len);
	/* If it's too soon to do another transaction, wait */
	if (ec_spi->last_transfer_ns) {
		unsigned long delay;	/* The delay completed so far */
		delay = ktime_get_ns() - ec_spi->last_transfer_ns;
		if (delay < EC_SPI_RECOVERY_TIME_NS)
			ndelay(EC_SPI_RECOVERY_TIME_NS - delay);
	}
	rx_buf = kzalloc(len, GFP_KERNEL);
	if (!rx_buf)
		return -ENOMEM;
	spi_bus_lock(ec_spi->spi->master);
	/*
         * Leave a gap between CS assertion and clocking of data to allow the
         * EC time to wakeup.
         */
	spi_message_init(&msg);
	if (ec_spi->start_of_msg_delay) {
		memset(&trans_delay, 0, sizeof(trans_delay));
		trans_delay.delay_usecs = ec_spi->start_of_msg_delay;
		spi_message_add_tail(&trans_delay, &msg);
	}
	/* Transmit phase - send our message */
	memset(&trans, 0, sizeof(trans));
	trans.tx_buf = ec_dev->dout;
	trans.rx_buf = rx_buf;
	trans.len = len;
	trans.cs_change = 1;
	spi_message_add_tail(&trans, &msg);
	ret = spi_sync_locked(ec_spi->spi, &msg);
	/* Get the response */
	if (!ret) {
		/* Verify that EC can process command */
		for (i = 0; i < len; i++) {
			switch (rx_buf[i]) {
			case EC_SPI_PAST_END:
			case EC_SPI_RX_BAD_DATA:
			case EC_SPI_NOT_READY:
				ret = -EAGAIN;
				ec_msg->result = EC_RES_IN_PROGRESS;
			default:
				break;
			}
			if (ret)
				break;
		}
		if (!ret)
			ret = cros_ec_spi_receive_packet(ec_dev,
					ec_msg->insize + sizeof(*response));
	} else {
		dev_err(ec_dev->dev, "spi transfer failed: %d\n", ret);
	}
	final_ret = terminate_request(ec_dev);
	spi_bus_unlock(ec_spi->spi->master);
	if (!ret)
		ret = final_ret;
	if (ret < 0)
		goto exit;
	ptr = ec_dev->din;
	/* check response error code */
	response = (struct ec_host_response *)ptr;
	ec_msg->result = response->result;
	ret = cros_ec_check_result(ec_dev, ec_msg);
	if (ret)
		goto exit;
	len = response->data_len;
	sum = 0;
	if (len > ec_msg->insize) {
		dev_err(ec_dev->dev, "packet too long (%d bytes, expected %d)",
			len, ec_msg->insize);
		ret = -EMSGSIZE;
		goto exit;
	}
	for (i = 0; i < sizeof(*response); i++)
		sum += ptr[i];
	/* copy response packet payload and compute checksum */
	memcpy(ec_msg->data, ptr + sizeof(*response), len);
	for (i = 0; i < len; i++)
		sum += ec_msg->data[i];
	if (sum) {
		dev_err(ec_dev->dev,
			"bad packet checksum, calculated %x\n",
			sum);
		ret = -EBADMSG;
		goto exit;
	}
	ret = len;
exit:
	kfree(rx_buf);
	if (ec_msg->command == EC_CMD_REBOOT_EC)
		msleep(EC_REBOOT_DELAY_MS);
	return ret;
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp | 
| Stephen Barber | 484 | 83.30% | 1 | 25.00% | 
| Alexandru M Stan | 47 | 8.09% | 1 | 25.00% | 
| Simon Glass | 30 | 5.16% | 1 | 25.00% | 
| Nicolas Boichat | 20 | 3.44% | 1 | 25.00% | 
| Total | 581 | 100.00% | 4 | 100.00% | 
/**
 * cros_ec_cmd_xfer_spi - Transfer a message over SPI and receive the reply
 *
 * @ec_dev: ChromeOS EC device
 * @ec_msg: Message to transfer
 */
static int cros_ec_cmd_xfer_spi(struct cros_ec_device *ec_dev,
				struct cros_ec_command *ec_msg)
{
	struct cros_ec_spi *ec_spi = ec_dev->priv;
	struct spi_transfer trans;
	struct spi_message msg;
	int i, len;
	u8 *ptr;
	u8 *rx_buf;
	int sum;
	int ret = 0, final_ret;
	len = cros_ec_prepare_tx(ec_dev, ec_msg);
	dev_dbg(ec_dev->dev, "prepared, len=%d\n", len);
	/* If it's too soon to do another transaction, wait */
	if (ec_spi->last_transfer_ns) {
		unsigned long delay;	/* The delay completed so far */
		delay = ktime_get_ns() - ec_spi->last_transfer_ns;
		if (delay < EC_SPI_RECOVERY_TIME_NS)
			ndelay(EC_SPI_RECOVERY_TIME_NS - delay);
	}
	rx_buf = kzalloc(len, GFP_KERNEL);
	if (!rx_buf)
		return -ENOMEM;
	spi_bus_lock(ec_spi->spi->master);
	/* Transmit phase - send our message */
	debug_packet(ec_dev->dev, "out", ec_dev->dout, len);
	memset(&trans, 0, sizeof(trans));
	trans.tx_buf = ec_dev->dout;
	trans.rx_buf = rx_buf;
	trans.len = len;
	trans.cs_change = 1;
	spi_message_init(&msg);
	spi_message_add_tail(&trans, &msg);
	ret = spi_sync_locked(ec_spi->spi, &msg);
	/* Get the response */
	if (!ret) {
		/* Verify that EC can process command */
		for (i = 0; i < len; i++) {
			switch (rx_buf[i]) {
			case EC_SPI_PAST_END:
			case EC_SPI_RX_BAD_DATA:
			case EC_SPI_NOT_READY:
				ret = -EAGAIN;
				ec_msg->result = EC_RES_IN_PROGRESS;
			default:
				break;
			}
			if (ret)
				break;
		}
		if (!ret)
			ret = cros_ec_spi_receive_response(ec_dev,
					ec_msg->insize + EC_MSG_TX_PROTO_BYTES);
	} else {
		dev_err(ec_dev->dev, "spi transfer failed: %d\n", ret);
	}
	final_ret = terminate_request(ec_dev);
	spi_bus_unlock(ec_spi->spi->master);
	if (!ret)
		ret = final_ret;
	if (ret < 0)
		goto exit;
	ptr = ec_dev->din;
	/* check response error code */
	ec_msg->result = ptr[0];
	ret = cros_ec_check_result(ec_dev, ec_msg);
	if (ret)
		goto exit;
	len = ptr[1];
	sum = ptr[0] + ptr[1];
	if (len > ec_msg->insize) {
		dev_err(ec_dev->dev, "packet too long (%d bytes, expected %d)",
			len, ec_msg->insize);
		ret = -ENOSPC;
		goto exit;
	}
	/* copy response packet payload and compute checksum */
	for (i = 0; i < len; i++) {
		sum += ptr[i + 2];
		if (ec_msg->insize)
			ec_msg->data[i] = ptr[i + 2];
	}
	sum &= 0xff;
	debug_packet(ec_dev->dev, "in", ptr, len + 3);
	if (sum != ptr[len + 2]) {
		dev_err(ec_dev->dev,
			"bad packet checksum, expected %02x, got %02x\n",
			sum, ptr[len + 2]);
		ret = -EBADMSG;
		goto exit;
	}
	ret = len;
exit:
	kfree(rx_buf);
	if (ec_msg->command == EC_CMD_REBOOT_EC)
		msleep(EC_REBOOT_DELAY_MS);
	return ret;
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp | 
| Simon Glass | 389 | 69.34% | 2 | 14.29% | 
| Stephen Barber | 91 | 16.22% | 1 | 7.14% | 
| Douglas Anderson | 39 | 6.95% | 2 | 14.29% | 
| Nicolas Boichat | 20 | 3.57% | 1 | 7.14% | 
| Bill Richardson | 16 | 2.85% | 4 | 28.57% | 
| Thomas Gleixner | 2 | 0.36% | 1 | 7.14% | 
| David Hendricks | 2 | 0.36% | 1 | 7.14% | 
| Javier Martinez Canillas | 1 | 0.18% | 1 | 7.14% | 
| Thierry Reding | 1 | 0.18% | 1 | 7.14% | 
| Total | 561 | 100.00% | 14 | 100.00% | 
static void cros_ec_spi_dt_probe(struct cros_ec_spi *ec_spi, struct device *dev)
{
	struct device_node *np = dev->of_node;
	u32 val;
	int ret;
	ret = of_property_read_u32(np, "google,cros-ec-spi-pre-delay", &val);
	if (!ret)
		ec_spi->start_of_msg_delay = val;
	ret = of_property_read_u32(np, "google,cros-ec-spi-msg-delay", &val);
	if (!ret)
		ec_spi->end_of_msg_delay = val;
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp | 
| Rhyland Klein | 54 | 70.13% | 1 | 50.00% | 
| Alexandru M Stan | 23 | 29.87% | 1 | 50.00% | 
| Total | 77 | 100.00% | 2 | 100.00% | 
static int cros_ec_spi_probe(struct spi_device *spi)
{
	struct device *dev = &spi->dev;
	struct cros_ec_device *ec_dev;
	struct cros_ec_spi *ec_spi;
	int err;
	spi->bits_per_word = 8;
	spi->mode = SPI_MODE_0;
	err = spi_setup(spi);
	if (err < 0)
		return err;
	ec_spi = devm_kzalloc(dev, sizeof(*ec_spi), GFP_KERNEL);
	if (ec_spi == NULL)
		return -ENOMEM;
	ec_spi->spi = spi;
	ec_dev = devm_kzalloc(dev, sizeof(*ec_dev), GFP_KERNEL);
	if (!ec_dev)
		return -ENOMEM;
	/* Check for any DT properties */
	cros_ec_spi_dt_probe(ec_spi, dev);
	spi_set_drvdata(spi, ec_dev);
	ec_dev->dev = dev;
	ec_dev->priv = ec_spi;
	ec_dev->irq = spi->irq;
	ec_dev->cmd_xfer = cros_ec_cmd_xfer_spi;
	ec_dev->pkt_xfer = cros_ec_pkt_xfer_spi;
	ec_dev->phys_name = dev_name(&ec_spi->spi->dev);
	ec_dev->din_size = EC_MSG_PREAMBLE_COUNT +
			   sizeof(struct ec_host_response) +
			   sizeof(struct ec_response_get_protocol_info);
	ec_dev->dout_size = sizeof(struct ec_host_request);
	err = cros_ec_register(ec_dev);
	if (err) {
		dev_err(dev, "cannot register EC\n");
		return err;
	}
	device_init_wakeup(&spi->dev, true);
	return 0;
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp | 
| Simon Glass | 198 | 81.82% | 1 | 14.29% | 
| Stephen Barber | 23 | 9.50% | 2 | 28.57% | 
| Prathyush K | 10 | 4.13% | 1 | 14.29% | 
| Rhyland Klein | 8 | 3.31% | 1 | 14.29% | 
| Bill Richardson | 2 | 0.83% | 1 | 14.29% | 
| Thierry Reding | 1 | 0.41% | 1 | 14.29% | 
| Total | 242 | 100.00% | 7 | 100.00% | 
static int cros_ec_spi_remove(struct spi_device *spi)
{
	struct cros_ec_device *ec_dev;
	ec_dev = spi_get_drvdata(spi);
	cros_ec_remove(ec_dev);
	return 0;
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp | 
| Simon Glass | 30 | 96.77% | 1 | 50.00% | 
| Thierry Reding | 1 | 3.23% | 1 | 50.00% | 
| Total | 31 | 100.00% | 2 | 100.00% | 
#ifdef CONFIG_PM_SLEEP
static int cros_ec_spi_suspend(struct device *dev)
{
	struct cros_ec_device *ec_dev = dev_get_drvdata(dev);
	return cros_ec_suspend(ec_dev);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp | 
| Simon Glass | 27 | 100.00% | 1 | 100.00% | 
| Total | 27 | 100.00% | 1 | 100.00% | 
static int cros_ec_spi_resume(struct device *dev)
{
	struct cros_ec_device *ec_dev = dev_get_drvdata(dev);
	return cros_ec_resume(ec_dev);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp | 
| Simon Glass | 27 | 100.00% | 1 | 100.00% | 
| Total | 27 | 100.00% | 1 | 100.00% | 
#endif
static SIMPLE_DEV_PM_OPS(cros_ec_spi_pm_ops, cros_ec_spi_suspend,
			 cros_ec_spi_resume);
static const struct of_device_id cros_ec_spi_of_match[] = {
	{ .compatible = "google,cros-ec-spi", },
	{ /* sentinel */ },
};
MODULE_DEVICE_TABLE(of, cros_ec_spi_of_match);
static const struct spi_device_id cros_ec_spi_id[] = {
	{ "cros-ec-spi", 0 },
	{ }
};
MODULE_DEVICE_TABLE(spi, cros_ec_spi_id);
static struct spi_driver cros_ec_driver_spi = {
	.driver	= {
		.name	= "cros-ec-spi",
		.of_match_table = of_match_ptr(cros_ec_spi_of_match),
		.pm	= &cros_ec_spi_pm_ops,
        },
	.probe		= cros_ec_spi_probe,
	.remove		= cros_ec_spi_remove,
	.id_table	= cros_ec_spi_id,
};
module_spi_driver(cros_ec_driver_spi);
MODULE_LICENSE("GPL v2");
MODULE_DESCRIPTION("ChromeOS EC multi function device (SPI)");
Overall Contributors
| Person | Tokens | Prop | Commits | CommitProp | 
| Stephen Barber | 1308 | 46.90% | 2 | 7.41% | 
| Simon Glass | 1160 | 41.59% | 2 | 7.41% | 
| Alexandru M Stan | 75 | 2.69% | 1 | 3.70% | 
| Rhyland Klein | 69 | 2.47% | 1 | 3.70% | 
| Douglas Anderson | 46 | 1.65% | 4 | 14.81% | 
| Nicolas Boichat | 42 | 1.51% | 1 | 3.70% | 
| Javier Martinez Canillas | 36 | 1.29% | 2 | 7.41% | 
| Bill Richardson | 19 | 0.68% | 4 | 14.81% | 
| Thierry Reding | 13 | 0.47% | 4 | 14.81% | 
| Prathyush K | 10 | 0.36% | 1 | 3.70% | 
| Lee Jones | 4 | 0.14% | 1 | 3.70% | 
| Derek Basehore | 2 | 0.07% | 1 | 3.70% | 
| David Hendricks | 2 | 0.07% | 1 | 3.70% | 
| Thomas Gleixner | 2 | 0.07% | 1 | 3.70% | 
| Geert Uytterhoeven | 1 | 0.04% | 1 | 3.70% | 
| Total | 2789 | 100.00% | 27 | 100.00% | 
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.