Release 4.12 include/linux/spi/spi_gpio.h
#ifndef __LINUX_SPI_GPIO_H
#define __LINUX_SPI_GPIO_H
/*
* For each bitbanged SPI bus, set up a platform_device node with:
* - name "spi_gpio"
* - id the same as the SPI bus number it implements
* - dev.platform data pointing to a struct spi_gpio_platform_data
*
* Or, see the driver code for information about speedups that are
* possible on platforms that support inlined access for GPIOs (no
* spi_gpio_platform_data is used).
*
* Use spi_board_info with these busses in the usual way, being sure
* that the controller_data being the GPIO used for each device's
* chipselect:
*
* static struct spi_board_info ... [] = {
* ...
* // this slave uses GPIO 42 for its chipselect
* .controller_data = (void *) 42,
* ...
* // this one uses GPIO 86 for its chipselect
* .controller_data = (void *) 86,
* ...
* };
*
* If chipselect is not used (there's only one device on the bus), assign
* SPI_GPIO_NO_CHIPSELECT to the controller_data:
* .controller_data = (void *) SPI_GPIO_NO_CHIPSELECT;
*
* If the MISO or MOSI pin is not available then it should be set to
* SPI_GPIO_NO_MISO or SPI_GPIO_NO_MOSI.
*
* If the bitbanged bus is later switched to a "native" controller,
* that platform_device and controller_data should be removed.
*/
#define SPI_GPIO_NO_CHIPSELECT ((unsigned long)-1l)
#define SPI_GPIO_NO_MISO ((unsigned long)-1l)
#define SPI_GPIO_NO_MOSI ((unsigned long)-1l)
/**
* struct spi_gpio_platform_data - parameter for bitbanged SPI master
* @sck: number of the GPIO used for clock output
* @mosi: number of the GPIO used for Master Output, Slave In (MOSI) data
* @miso: number of the GPIO used for Master Input, Slave Output (MISO) data
* @num_chipselect: how many slaves to allow
*
* All GPIO signals used with the SPI bus managed through this driver
* (chipselects, MOSI, MISO, SCK) must be configured as GPIOs, instead
* of some alternate function.
*
* It can be convenient to use this driver with pins that have alternate
* functions associated with a "native" SPI controller if a driver for that
* controller is not available, or is missing important functionality.
*
* On platforms which can do so, configure MISO with a weak pullup unless
* there's an external pullup on that signal. That saves power by avoiding
* floating signals. (A weak pulldown would save power too, but many
* drivers expect to see all-ones data as the no slave "response".)
*/
struct spi_gpio_platform_data {
unsigned sck;
unsigned long mosi;
unsigned long miso;
u16 num_chipselect;
};
#endif /* __LINUX_SPI_GPIO_H */
Overall Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| David Brownell | 27 | 64.29% | 1 | 25.00% |
| Marek Szyprowski | 9 | 21.43% | 1 | 25.00% |
| Michael Büsch | 4 | 9.52% | 1 | 25.00% |
| Maxime Ripard | 2 | 4.76% | 1 | 25.00% |
| Total | 42 | 100.00% | 4 | 100.00% |
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.