Release 4.12 include/linux/usb/musb.h
/*
* This is used to for host and peripheral modes of the driver for
* Inventra (Multidrop) Highspeed Dual-Role Controllers: (M)HDRC.
*
* Board initialization should put one of these into dev->platform_data,
* probably on some platform_device named "musb-hdrc". It encapsulates
* key configuration differences between boards.
*/
#ifndef __LINUX_USB_MUSB_H
#define __LINUX_USB_MUSB_H
/* The USB role is defined by the connector used on the board, so long as
* standards are being followed. (Developer boards sometimes won't.)
*/
enum musb_mode {
MUSB_UNDEFINED = 0,
MUSB_HOST, /* A or Mini-A connector */
MUSB_PERIPHERAL, /* B or Mini-B connector */
MUSB_OTG /* Mini-AB connector */
};
struct clk;
enum musb_fifo_style {
FIFO_RXTX,
FIFO_TX,
FIFO_RX
} __attribute__ ((packed));
enum musb_buf_mode {
BUF_SINGLE,
BUF_DOUBLE
} __attribute__ ((packed));
struct musb_fifo_cfg {
u8 hw_ep_num;
enum musb_fifo_style style;
enum musb_buf_mode mode;
u16 maxpacket;
};
#define MUSB_EP_FIFO(ep, st, m, pkt) \
{ \
.hw_ep_num = ep, \
.style = st, \
.mode = m, \
.maxpacket = pkt, \
}
#define MUSB_EP_FIFO_SINGLE(ep, st, pkt) \
MUSB_EP_FIFO(ep, st, BUF_SINGLE, pkt)
#define MUSB_EP_FIFO_DOUBLE(ep, st, pkt) \
MUSB_EP_FIFO(ep, st, BUF_DOUBLE, pkt)
struct musb_hdrc_eps_bits {
const char name[16];
u8 bits;
};
struct musb_hdrc_config {
struct musb_fifo_cfg *fifo_cfg; /* board fifo configuration */
unsigned fifo_cfg_size; /* size of the fifo configuration */
/* MUSB configuration-specific details */
unsigned multipoint:1; /* multipoint device */
unsigned dyn_fifo:1 __deprecated; /* supports dynamic fifo sizing */
unsigned soft_con:1 __deprecated; /* soft connect required */
unsigned utm_16:1 __deprecated; /* utm data witdh is 16 bits */
unsigned big_endian:1; /* true if CPU uses big-endian */
unsigned mult_bulk_tx:1; /* Tx ep required for multbulk pkts */
unsigned mult_bulk_rx:1; /* Rx ep required for multbulk pkts */
unsigned high_iso_tx:1; /* Tx ep required for HB iso */
unsigned high_iso_rx:1; /* Rx ep required for HD iso */
unsigned dma:1 __deprecated; /* supports DMA */
unsigned vendor_req:1 __deprecated; /* vendor registers required */
/* need to explicitly de-assert the port reset after resume? */
unsigned host_port_deassert_reset_at_resume:1;
u8 num_eps; /* number of endpoints _with_ ep0 */
u8 dma_channels __deprecated; /* number of dma channels */
u8 dyn_fifo_size; /* dynamic size in bytes */
u8 vendor_ctrl __deprecated; /* vendor control reg width */
u8 vendor_stat __deprecated; /* vendor status reg witdh */
u8 dma_req_chan __deprecated; /* bitmask for required dma channels */
u8 ram_bits; /* ram address size */
struct musb_hdrc_eps_bits *eps_bits __deprecated;
#ifdef CONFIG_BLACKFIN
/* A GPIO controlling VRSEL in Blackfin */
unsigned int gpio_vrsel;
unsigned int gpio_vrsel_active;
/* musb CLKIN in Blackfin in MHZ */
unsigned char clkin;
#endif
u32 maximum_speed;
};
struct musb_hdrc_platform_data {
/* MUSB_HOST, MUSB_PERIPHERAL, or MUSB_OTG */
u8 mode;
/* for clk_get() */
const char *clock;
/* (HOST or OTG) switch VBUS on/off */
int (*set_vbus)(struct device *dev, int is_on);
/* (HOST or OTG) mA/2 power supplied on (default = 8mA) */
u8 power;
/* (PERIPHERAL) mA/2 max power consumed (default = 100mA) */
u8 min_power;
/* (HOST or OTG) msec/2 after VBUS on till power good */
u8 potpgt;
/* (HOST or OTG) program PHY for external Vbus */
unsigned extvbus:1;
/* Power the device on or off */
int (*set_power)(int state);
/* MUSB configuration-specific details */
const struct musb_hdrc_config *config;
/* Architecture specific board data */
void *board_data;
/* Platform specific struct musb_ops pointer */
const void *platform_ops;
};
enum musb_vbus_id_status {
MUSB_UNKNOWN = 0,
MUSB_ID_GROUND,
MUSB_ID_FLOAT,
MUSB_VBUS_VALID,
MUSB_VBUS_OFF,
};
#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
int musb_mailbox(enum musb_vbus_id_status status);
#else
static inline int musb_mailbox(enum musb_vbus_id_status status)
{
return 0;
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| Tony Lindgren | 14 | 100.00% | 2 | 100.00% |
| Total | 14 | 100.00% | 2 | 100.00% |
#endif
/* TUSB 6010 support */
#define TUSB6010_OSCCLK_60 16667
/* psec/clk @ 60.0 MHz */
#define TUSB6010_REFCLK_24 41667
/* psec/clk @ 24.0 MHz XI */
#define TUSB6010_REFCLK_19 52083
/* psec/clk @ 19.2 MHz CLKIN */
#ifdef CONFIG_ARCH_OMAP2
extern int __init tusb6010_setup_interface(
struct musb_hdrc_platform_data *data,
unsigned ps_refclk, unsigned waitpin,
unsigned async_cs, unsigned sync_cs,
unsigned irq, unsigned dmachan);
extern int tusb6010_platform_retime(unsigned is_refclk);
#endif /* OMAP2 */
#endif /* __LINUX_USB_MUSB_H */
Overall Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| Felipe Balbi | 374 | 79.41% | 6 | 35.29% |
| Tony Lindgren | 48 | 10.19% | 2 | 11.76% |
| Bryan Wu | 10 | 2.12% | 1 | 5.88% |
| Mark A. Greer | 9 | 1.91% | 1 | 5.88% |
| Ajay Kumar Gupta | 6 | 1.27% | 1 | 5.88% |
| Daniel Mack | 6 | 1.27% | 1 | 5.88% |
| Bob Liu | 5 | 1.06% | 1 | 5.88% |
| Maulik Mankad | 5 | 1.06% | 1 | 5.88% |
| Cliff Cai | 4 | 0.85% | 1 | 5.88% |
| Bin Liu | 3 | 0.64% | 1 | 5.88% |
| Petr Kulhavy | 1 | 0.21% | 1 | 5.88% |
| Total | 471 | 100.00% | 17 | 100.00% |
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.