Release 4.14 arch/blackfin/mach-bf533/boards/blackstamp.c
/*
* Board Info File for the BlackStamp
*
* Copyright 2004-2008 Analog Devices Inc.
* 2008 Benjamin Matthews <bmat@lle.rochester.edu>
* 2005 National ICT Australia (NICTA)
* Aidan Williams <aidan@nicta.com.au>
*
* More info about the BlackStamp at:
* http://blackfin.uclinux.org/gf/project/blackstamp/
*
* Licensed under the GPL-2 or later.
*/
#include <linux/device.h>
#include <linux/platform_device.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#include <linux/irq.h>
#include <linux/gpio.h>
#include <linux/i2c.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
#include <asm/portmux.h>
#include <asm/dpmc.h>
/*
* Name the Board for the /proc/cpuinfo
*/
const char bfin_board_name[] = "BlackStamp";
#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
};
#endif
/*
* Driver needs to know address, irq and flag pin.
*/
#if IS_ENABLED(CONFIG_SMC91X)
#include <linux/smc91x.h>
static struct smc91x_platdata smc91x_info = {
.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
.leda = RPC_LED_100_10,
.ledb = RPC_LED_TX_RX,
};
static struct resource smc91x_resources[] = {
{
.name = "smc91x-regs",
.start = 0x20300300,
.end = 0x20300300 + 16,
.flags = IORESOURCE_MEM,
}, {
.start = IRQ_PF3,
.end = IRQ_PF3,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
},
};
static struct platform_device smc91x_device = {
.name = "smc91x",
.id = 0,
.num_resources = ARRAY_SIZE(smc91x_resources),
.resource = smc91x_resources,
.dev = {
.platform_data = &smc91x_info,
},
};
#endif
#if IS_ENABLED(CONFIG_MTD_M25P80)
static struct mtd_partition bfin_spi_flash_partitions[] = {
{
.name = "bootloader(spi)",
.size = 0x00040000,
.offset = 0,
.mask_flags = MTD_CAP_ROM
}, {
.name = "linux kernel(spi)",
.size = 0x180000,
.offset = MTDPART_OFS_APPEND,
}, {
.name = "file system(spi)",
.size = MTDPART_SIZ_FULL,
.offset = MTDPART_OFS_APPEND,
}
};
static struct flash_platform_data bfin_spi_flash_data = {
.name = "m25p80",
.parts = bfin_spi_flash_partitions,
.nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
.type = "m25p64",
};
/* SPI flash chip (m25p64) */
static struct bfin5xx_spi_chip spi_flash_chip_info = {
.enable_dma = 0, /* use dma transfer with this chip*/
};
#endif
#if IS_ENABLED(CONFIG_MMC_SPI)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
};
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
#if IS_ENABLED(CONFIG_MTD_M25P80)
{
/* the modalias must be the same as spi device driver name */
.modalias = "m25p80", /* Name of spi_driver for this device */
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0, /* Framework bus number */
.chip_select = 2, /* Framework chip select. */
.platform_data = &bfin_spi_flash_data,
.controller_data = &spi_flash_chip_info,
.mode = SPI_MODE_3,
},
#endif
#if IS_ENABLED(CONFIG_MMC_SPI)
{
.modalias = "mmc_spi",
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 5,
.controller_data = &mmc_spi_chip_info,
.mode = SPI_MODE_3,
},
#endif
#if IS_ENABLED(CONFIG_SPI_SPIDEV)
{
.modalias = "spidev",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
.chip_select = 7,
},
#endif
};
#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
/* SPI (0) */
static struct resource bfin_spi0_resource[] = {
[0] = {
.start = SPI0_REGBASE,
.end = SPI0_REGBASE + 0xFF,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = CH_SPI,
.end = CH_SPI,
.flags = IORESOURCE_DMA,
},
[2] = {
.start = IRQ_SPI,
.end = IRQ_SPI,
.flags = IORESOURCE_IRQ,
}
};
/* SPI controller data */
static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 8,
.enable_dma = 1, /* master has the ability to do dma transfer */
.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
};
static struct platform_device bfin_spi0_device = {
.name = "bfin-spi",
.id = 0, /* Bus number */
.num_resources = ARRAY_SIZE(bfin_spi0_resource),
.resource = bfin_spi0_resource,
.dev = {
.platform_data = &bfin_spi0_info, /* Passed to driver */
},
};
#endif /* spi master and devices */
#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
.start = BFIN_UART_THR,
.end = BFIN_UART_GCTL+2,
.flags = IORESOURCE_MEM,
},
{
.start = IRQ_UART0_TX,
.end = IRQ_UART0_TX,
.flags = IORESOURCE_IRQ,
},
{
.start = IRQ_UART0_RX,
.end = IRQ_UART0_RX,
.flags = IORESOURCE_IRQ,
},
{
.start = IRQ_UART0_ERROR,
.end = IRQ_UART0_ERROR,
.flags = IORESOURCE_IRQ,
},
{
.start = CH_UART0_TX,
.end = CH_UART0_TX,
.flags = IORESOURCE_DMA,
},
{
.start = CH_UART0_RX,
.end = CH_UART0_RX,
.flags = IORESOURCE_DMA,
},
};
static unsigned short bfin_uart0_peripherals[] = {
P_UART0_TX, P_UART0_RX, 0
};
static struct platform_device bfin_uart0_device = {
.name = "bfin-uart",
.id = 0,
.num_resources = ARRAY_SIZE(bfin_uart0_resources),
.resource = bfin_uart0_resources,
.dev = {
.platform_data = &bfin_uart0_peripherals, /* Passed to driver */
},
};
#endif
#endif
#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
static struct resource bfin_sir0_resources[] = {
{
.start = 0xFFC00400,
.end = 0xFFC004FF,
.flags = IORESOURCE_MEM,
},
{
.start = IRQ_UART0_RX,
.end = IRQ_UART0_RX+1,
.flags = IORESOURCE_IRQ,
},
{
.start = CH_UART0_RX,
.end = CH_UART0_RX+1,
.flags = IORESOURCE_DMA,
},
};
static struct platform_device bfin_sir0_device = {
.name = "bfin_sir",
.id = 0,
.num_resources = ARRAY_SIZE(bfin_sir0_resources),
.resource = bfin_sir0_resources,
};
#endif
#endif
#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
static struct resource bfin_sport0_uart_resources[] = {
{
.start = SPORT0_TCR1,
.end = SPORT0_MRCS3+4,
.flags = IORESOURCE_MEM,
},
{
.start = IRQ_SPORT0_RX,
.end = IRQ_SPORT0_RX+1,
.flags = IORESOURCE_IRQ,
},
{
.start = IRQ_SPORT0_ERROR,
.end = IRQ_SPORT0_ERROR,
.flags = IORESOURCE_IRQ,
},
};
static unsigned short bfin_sport0_peripherals[] = {
P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
P_SPORT0_DRPRI, P_SPORT0_RSCLK, 0
};
static struct platform_device bfin_sport0_uart_device = {
.name = "bfin-sport-uart",
.id = 0,
.num_resources = ARRAY_SIZE(bfin_sport0_uart_resources),
.resource = bfin_sport0_uart_resources,
.dev = {
.platform_data = &bfin_sport0_peripherals, /* Passed to driver */
},
};
#endif
#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
static struct resource bfin_sport1_uart_resources[] = {
{
.start = SPORT1_TCR1,
.end = SPORT1_MRCS3+4,
.flags = IORESOURCE_MEM,
},
{
.start = IRQ_SPORT1_RX,
.end = IRQ_SPORT1_RX+1,
.flags = IORESOURCE_IRQ,
},
{
.start = IRQ_SPORT1_ERROR,
.end = IRQ_SPORT1_ERROR,
.flags = IORESOURCE_IRQ,
},
};
static unsigned short bfin_sport1_peripherals[] = {
P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS,
P_SPORT1_DRPRI, P_SPORT1_RSCLK, 0
};
static struct platform_device bfin_sport1_uart_device = {
.name = "bfin-sport-uart",
.id = 1,
.num_resources = ARRAY_SIZE(bfin_sport1_uart_resources),
.resource = bfin_sport1_uart_resources,
.dev = {
.platform_data = &bfin_sport1_peripherals, /* Passed to driver */
},
};
#endif
#endif
#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
#include <linux/input.h>
#include <linux/gpio_keys.h>
static struct gpio_keys_button bfin_gpio_keys_table[] = {
{BTN_0, GPIO_PF4, 0, "gpio-keys: BTN0"},
{BTN_1, GPIO_PF5, 0, "gpio-keys: BTN1"},
{BTN_2, GPIO_PF6, 0, "gpio-keys: BTN2"},
}; /* Mapped to the first three PF Test Points */
static struct gpio_keys_platform_data bfin_gpio_keys_data = {
.buttons = bfin_gpio_keys_table,
.nbuttons = ARRAY_SIZE(bfin_gpio_keys_table),
};
static struct platform_device bfin_device_gpiokeys = {
.name = "gpio-keys",
.dev = {
.platform_data = &bfin_gpio_keys_data,
},
};
#endif
#if IS_ENABLED(CONFIG_I2C_GPIO)
#include <linux/i2c-gpio.h>
static struct i2c_gpio_platform_data i2c_gpio_data = {
.sda_pin = GPIO_PF8,
.scl_pin = GPIO_PF9,
.sda_is_open_drain = 0,
.scl_is_open_drain = 0,
.udelay = 40,
}; /* This hasn't actually been used these pins
* are (currently) free pins on the expansion connector */
static struct platform_device i2c_gpio_device = {
.name = "i2c-gpio",
.id = 0,
.dev = {
.platform_data = &i2c_gpio_data,
},
};
#endif
static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
};
static const unsigned int cclk_vlev_datasheet[] =
{
VRPAIR(VLEV_085, 250000000),
VRPAIR(VLEV_090, 376000000),
VRPAIR(VLEV_095, 426000000),
VRPAIR(VLEV_100, 426000000),
VRPAIR(VLEV_105, 476000000),
VRPAIR(VLEV_110, 476000000),
VRPAIR(VLEV_115, 476000000),
VRPAIR(VLEV_120, 600000000),
VRPAIR(VLEV_125, 600000000),
VRPAIR(VLEV_130, 600000000),
};
static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
.tuple_tab = cclk_vlev_datasheet,
.tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
.vr_settling_time = 25 /* us */,
};
static struct platform_device bfin_dpmc = {
.name = "bfin dpmc",
.dev = {
.platform_data = &bfin_dmpc_vreg_data,
},
};
static struct platform_device *stamp_devices[] __initdata = {
&bfin_dpmc,
#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
&rtc_device,
#endif
#if IS_ENABLED(CONFIG_SMC91X)
&smc91x_device,
#endif
#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
&bfin_spi0_device,
#endif
#if IS_ENABLED(CONFIG_SERIAL_BFIN)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
#if IS_ENABLED(CONFIG_BFIN_SIR)
#ifdef CONFIG_BFIN_SIR0
&bfin_sir0_device,
#endif
#endif
#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
&bfin_sport0_uart_device,
#endif
#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
&bfin_sport1_uart_device,
#endif
#endif
#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
&bfin_device_gpiokeys,
#endif
#if IS_ENABLED(CONFIG_I2C_GPIO)
&i2c_gpio_device,
#endif
};
static int __init blackstamp_init(void)
{
int ret;
printk(KERN_INFO "%s(): registering device resources\n", __func__);
i2c_register_board_info(0, bfin_i2c_board_info,
ARRAY_SIZE(bfin_i2c_board_info));
ret = platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
if (ret < 0)
return ret;
#if IS_ENABLED(CONFIG_SMC91X)
/*
* setup BF533_STAMP CPLD to route AMS3 to Ethernet MAC.
* the bfin-async-map driver takes care of flipping between
* flash and ethernet when necessary.
*/
ret = gpio_request(GPIO_PF0, "enet_cpld");
if (!ret) {
gpio_direction_output(GPIO_PF0, 1);
gpio_free(GPIO_PF0);
}
#endif
spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
return 0;
}
Contributors
Person | Tokens | Prop | Commits | CommitProp |
Benjamin Matthews | 80 | 77.67% | 1 | 33.33% |
Mike Frysinger | 22 | 21.36% | 1 | 33.33% |
Steven Miao | 1 | 0.97% | 1 | 33.33% |
Total | 103 | 100.00% | 3 | 100.00% |
arch_initcall(blackstamp_init);
static struct platform_device *stamp_early_devices[] __initdata = {
#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#endif
#if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE)
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
&bfin_sport0_uart_device,
#endif
#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
&bfin_sport1_uart_device,
#endif
#endif
};
void __init native_machine_early_platform_add_devices(void)
{
printk(KERN_INFO "register early platform devices\n");
early_platform_add_devices(stamp_early_devices,
ARRAY_SIZE(stamp_early_devices));
}
Contributors
Person | Tokens | Prop | Commits | CommitProp |
Sonic Zhang | 24 | 100.00% | 1 | 100.00% |
Total | 24 | 100.00% | 1 | 100.00% |
Overall Contributors
Person | Tokens | Prop | Commits | CommitProp |
Benjamin Matthews | 1189 | 65.47% | 1 | 5.56% |
Sonic Zhang | 453 | 24.94% | 5 | 27.78% |
Graf Yang | 53 | 2.92% | 1 | 5.56% |
Michael Hennerich | 45 | 2.48% | 2 | 11.11% |
Mike Frysinger | 29 | 1.60% | 5 | 27.78% |
Steven Miao | 25 | 1.38% | 2 | 11.11% |
Yi Li | 21 | 1.16% | 1 | 5.56% |
Robin Getz | 1 | 0.06% | 1 | 5.56% |
Total | 1816 | 100.00% | 18 | 100.00% |
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.