cregit-Linux how code gets into the kernel

Release 4.14 arch/sparc/include/asm/dma.h

/* SPDX-License-Identifier: GPL-2.0 */
#ifndef _ASM_SPARC_DMA_H

#define _ASM_SPARC_DMA_H

/* These are irrelevant for Sparc DMA, but we leave it in so that
 * things can compile.
 */

#define MAX_DMA_CHANNELS 8

#define DMA_MODE_READ    1

#define DMA_MODE_WRITE   2

#define MAX_DMA_ADDRESS  (~0UL)

/* Useful constants */

#define SIZE_16MB      (16*1024*1024)

#define SIZE_64K       (64*1024)

/* SBUS DMA controller reg offsets */

#define DMA_CSR		0x00UL		
/* rw  DMA control/status register    0x00   */

#define DMA_ADDR	0x04UL		
/* rw  DMA transfer address register  0x04   */

#define DMA_COUNT	0x08UL		
/* rw  DMA transfer count register    0x08   */

#define DMA_TEST	0x0cUL		
/* rw  DMA test/debug register        0x0c   */

/* Fields in the cond_reg register */
/* First, the version identification bits */

#define DMA_DEVICE_ID    0xf0000000        
/* Device identification bits */

#define DMA_VERS0        0x00000000        
/* Sunray DMA version */

#define DMA_ESCV1        0x40000000        
/* DMA ESC Version 1 */

#define DMA_VERS1        0x80000000        
/* DMA rev 1 */

#define DMA_VERS2        0xa0000000        
/* DMA rev 2 */

#define DMA_VERHME       0xb0000000        
/* DMA hme gate array */

#define DMA_VERSPLUS     0x90000000        
/* DMA rev 1 PLUS */


#define DMA_HNDL_INTR    0x00000001        
/* An IRQ needs to be handled */

#define DMA_HNDL_ERROR   0x00000002        
/* We need to take an error */

#define DMA_FIFO_ISDRAIN 0x0000000c        
/* The DMA FIFO is draining */

#define DMA_INT_ENAB     0x00000010        
/* Turn on interrupts */

#define DMA_FIFO_INV     0x00000020        
/* Invalidate the FIFO */

#define DMA_ACC_SZ_ERR   0x00000040        
/* The access size was bad */

#define DMA_FIFO_STDRAIN 0x00000040        
/* DMA_VERS1 Drain the FIFO */

#define DMA_RST_SCSI     0x00000080        
/* Reset the SCSI controller */

#define DMA_RST_ENET     DMA_RST_SCSI      
/* Reset the ENET controller */

#define DMA_ST_WRITE     0x00000100        
/* write from device to memory */

#define DMA_ENABLE       0x00000200        
/* Fire up DMA, handle requests */

#define DMA_PEND_READ    0x00000400        
/* DMA_VERS1/0/PLUS Pending Read */

#define DMA_ESC_BURST    0x00000800        
/* 1=16byte 0=32byte */

#define DMA_READ_AHEAD   0x00001800        
/* DMA read ahead partial longword */

#define DMA_DSBL_RD_DRN  0x00001000        
/* No EC drain on slave reads */

#define DMA_BCNT_ENAB    0x00002000        
/* If on, use the byte counter */

#define DMA_TERM_CNTR    0x00004000        
/* Terminal counter */

#define DMA_SCSI_SBUS64  0x00008000        
/* HME: Enable 64-bit SBUS mode. */

#define DMA_CSR_DISAB    0x00010000        
/* No FIFO drains during csr */

#define DMA_SCSI_DISAB   0x00020000        
/* No FIFO drains during reg */

#define DMA_DSBL_WR_INV  0x00020000        
/* No EC inval. on slave writes */

#define DMA_ADD_ENABLE   0x00040000        
/* Special ESC DVMA optimization */

#define DMA_E_BURSTS	 0x000c0000	   
/* ENET: SBUS r/w burst mask */

#define DMA_E_BURST32	 0x00040000	   
/* ENET: SBUS 32 byte r/w burst */

#define DMA_E_BURST16	 0x00000000	   
/* ENET: SBUS 16 byte r/w burst */

#define DMA_BRST_SZ      0x000c0000        
/* SCSI: SBUS r/w burst size */

#define DMA_BRST64       0x000c0000        
/* SCSI: 64byte bursts (HME on UltraSparc only) */

#define DMA_BRST32       0x00040000        
/* SCSI: 32byte bursts */

#define DMA_BRST16       0x00000000        
/* SCSI: 16byte bursts */

#define DMA_BRST0        0x00080000        
/* SCSI: no bursts (non-HME gate arrays) */

#define DMA_ADDR_DISAB   0x00100000        
/* No FIFO drains during addr */

#define DMA_2CLKS        0x00200000        
/* Each transfer = 2 clock ticks */

#define DMA_3CLKS        0x00400000        
/* Each transfer = 3 clock ticks */

#define DMA_EN_ENETAUI   DMA_3CLKS         
/* Put lance into AUI-cable mode */

#define DMA_CNTR_DISAB   0x00800000        
/* No IRQ when DMA_TERM_CNTR set */

#define DMA_AUTO_NADDR   0x01000000        
/* Use "auto nxt addr" feature */

#define DMA_SCSI_ON      0x02000000        
/* Enable SCSI dma */

#define DMA_PARITY_OFF   0x02000000        
/* HME: disable parity checking */

#define DMA_LOADED_ADDR  0x04000000        
/* Address has been loaded */

#define DMA_LOADED_NADDR 0x08000000        
/* Next address has been loaded */

#define DMA_RESET_FAS366 0x08000000        
/* HME: Assert RESET to FAS366 */

/* Values describing the burst-size property from the PROM */

#define DMA_BURST1       0x01

#define DMA_BURST2       0x02

#define DMA_BURST4       0x04

#define DMA_BURST8       0x08

#define DMA_BURST16      0x10

#define DMA_BURST32      0x20

#define DMA_BURST64      0x40

#define DMA_BURSTBITS    0x7f

/* From PCI */

#ifdef CONFIG_PCI
extern int isa_dma_bridge_buggy;
#else

#define isa_dma_bridge_buggy 	(0)
#endif

#ifdef CONFIG_SPARC32

/* Routines for data transfer buffers. */
struct device;
struct scatterlist;


struct sparc32_dma_ops {
	
__u32 (*get_scsi_one)(struct device *, char *, unsigned long);
	
void (*get_scsi_sgl)(struct device *, struct scatterlist *, int);
	
void (*release_scsi_one)(struct device *, __u32, unsigned long);
	
void (*release_scsi_sgl)(struct device *, struct scatterlist *,int);
#ifdef CONFIG_SBUS
	
int (*map_dma_area)(struct device *, dma_addr_t *, unsigned long, unsigned long, int);
	
void (*unmap_dma_area)(struct device *, unsigned long, int);
#endif
};
extern const struct sparc32_dma_ops *sparc32_dma_ops;


#define mmu_get_scsi_one(dev,vaddr,len) \
	sparc32_dma_ops->get_scsi_one(dev, vaddr, len)

#define mmu_get_scsi_sgl(dev,sg,sz) \
	sparc32_dma_ops->get_scsi_sgl(dev, sg, sz)

#define mmu_release_scsi_one(dev,vaddr,len) \
	sparc32_dma_ops->release_scsi_one(dev, vaddr,len)

#define mmu_release_scsi_sgl(dev,sg,sz) \
	sparc32_dma_ops->release_scsi_sgl(dev, sg, sz)

#ifdef CONFIG_SBUS
/*
 * mmu_map/unmap are provided by iommu/iounit; Invalid to call on IIep.
 *
 * The mmu_map_dma_area establishes two mappings in one go.
 * These mappings point to pages normally mapped at 'va' (linear address).
 * First mapping is for CPU visible address at 'a', uncached.
 * This is an alias, but it works because it is an uncached mapping.
 * Second mapping is for device visible address, or "bus" address.
 * The bus address is returned at '*pba'.
 *
 * These functions seem distinct, but are hard to split.
 * On sun4m, page attributes depend on the CPU type, so we have to
 * know if we are mapping RAM or I/O, so it has to be an additional argument
 * to a separate mapping function for CPU visible mappings.
 */

#define sbus_map_dma_area(dev,pba,va,a,len) \
	sparc32_dma_ops->map_dma_area(dev, pba, va, a, len)

#define sbus_unmap_dma_area(dev,ba,len) \
	sparc32_dma_ops->unmap_dma_area(dev, ba, len)
#endif /* CONFIG_SBUS */

#endif

#endif /* !(_ASM_SPARC_DMA_H) */

Overall Contributors

PersonTokensPropCommitsCommitProp
David S. Miller55498.05%550.00%
Linus Torvalds (pre-git)81.42%330.00%
Sam Ravnborg20.35%110.00%
Greg Kroah-Hartman10.18%110.00%
Total565100.00%10100.00%
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.
Created with cregit.