Release 4.14 arch/x86/pci/intel_mid_pci.c

// SPDX-License-Identifier: GPL-2.0
/*
 * Intel MID PCI support
 *   Copyright (c) 2008 Intel Corporation
 *     Jesse Barnes <jesse.barnes@intel.com>
 *
 * Moorestown has an interesting PCI implementation:
 *   - configuration space is memory mapped (as defined by MCFG)
 *   - Lincroft devices also have a real, type 1 configuration space
 *   - Early Lincroft silicon has a type 1 access bug that will cause
 *     a hang if non-existent devices are accessed
 *   - some devices have the "fixed BAR" capability, which means
 *     they can't be relocated or modified; check for that during
 *     BAR sizing
 *
 * So, we use the MCFG space for all reads and writes, but also send
 * Lincroft writes to type 1 space.  But only read/write if the device
 * actually exists, otherwise return all 1s for reads and bit bucket
 * the writes.
 */

#include <linux/sched.h>
#include <linux/pci.h>
#include <linux/ioport.h>
#include <linux/init.h>
#include <linux/dmi.h>
#include <linux/acpi.h>
#include <linux/io.h>
#include <linux/smp.h>

#include <asm/segment.h>
#include <asm/pci_x86.h>
#include <asm/hw_irq.h>
#include <asm/io_apic.h>
#include <asm/intel-mid.h>


#define PCIE_CAP_OFFSET	0x100

/* Quirks for the listed devices */

#define PCI_DEVICE_ID_INTEL_MRFLD_MMC	0x1190

#define PCI_DEVICE_ID_INTEL_MRFLD_HSU	0x1191

/* Fixed BAR fields */

#define PCIE_VNDR_CAP_ID_FIXED_BAR 0x00	
/* Fixed BAR (TBD) */

#define PCI_FIXED_BAR_0_SIZE	0x04

#define PCI_FIXED_BAR_1_SIZE	0x08

#define PCI_FIXED_BAR_2_SIZE	0x0c

#define PCI_FIXED_BAR_3_SIZE	0x10

#define PCI_FIXED_BAR_4_SIZE	0x14

#define PCI_FIXED_BAR_5_SIZE	0x1c


static int pci_soc_mode;

/**
 * fixed_bar_cap - return the offset of the fixed BAR cap if found
 * @bus: PCI bus
 * @devfn: device in question
 *
 * Look for the fixed BAR cap on @bus and @devfn, returning its offset
 * if found or 0 otherwise.
 */


static int fixed_bar_cap(struct pci_bus *bus, unsigned int devfn)
{
	int pos;
	u32 pcie_cap = 0, cap_data;

	pos = PCIE_CAP_OFFSET;

	if (!raw_pci_ext_ops)
		return 0;

	while (pos) {
		if (raw_pci_ext_ops->read(pci_domain_nr(bus), bus->number,
					  devfn, pos, 4, &pcie_cap))
			return 0;

		if (PCI_EXT_CAP_ID(pcie_cap) == 0x0000 ||
			PCI_EXT_CAP_ID(pcie_cap) == 0xffff)
			break;

		if (PCI_EXT_CAP_ID(pcie_cap) == PCI_EXT_CAP_ID_VNDR) {
			raw_pci_ext_ops->read(pci_domain_nr(bus), bus->number,
					      devfn, pos + 4, 4, &cap_data);
			if ((cap_data & 0xffff) == PCIE_VNDR_CAP_ID_FIXED_BAR)
				return pos;
		}

		pos = PCI_EXT_CAP_NEXT(pcie_cap);
	}

	return 0;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
Jesse Barnes
124
84.35%
1
33.33%
Jacob jun Pan
23
15.65%
2
66.67%
Total
147
100.00%
3
100.00%



static int pci_device_update_fixed(struct pci_bus *bus, unsigned int devfn,
				   int reg, int len, u32 val, int offset)
{
	u32 size;
	unsigned int domain, busnum;
	int bar = (reg - PCI_BASE_ADDRESS_0) >> 2;

	domain = pci_domain_nr(bus);
	busnum = bus->number;

	if (val == ~0 && len == 4) {
		unsigned long decode;

		raw_pci_ext_ops->read(domain, busnum, devfn,
			       offset + 8 + (bar * 4), 4, &size);

		/* Turn the size into a decode pattern for the sizing code */
		if (size) {
			decode = size - 1;
			decode |= decode >> 1;
			decode |= decode >> 2;
			decode |= decode >> 4;
			decode |= decode >> 8;
			decode |= decode >> 16;
			decode++;
			decode = ~(decode - 1);
		} else {
			decode = 0;
		}

		/*
                 * If val is all ones, the core code is trying to size the reg,
                 * so update the mmconfig space with the real size.
                 *
                 * Note: this assumes the fixed size we got is a power of two.
                 */
		return raw_pci_ext_ops->write(domain, busnum, devfn, reg, 4,
				       decode);
	}

	/* This is some other kind of BAR write, so just do it. */
	return raw_pci_ext_ops->write(domain, busnum, devfn, reg, len, val);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
Jesse Barnes
203
100.00%
1
100.00%
Total
203
100.00%
1
100.00%

/**
 * type1_access_ok - check whether to use type 1
 * @bus: bus number
 * @devfn: device & function in question
 *
 * If the bus is on a Lincroft chip and it exists, or is not on a Lincroft at
 * all, the we can go ahead with any reads & writes.  If it's on a Lincroft,
 * but doesn't exist, avoid the access altogether to keep the chip from
 * hanging.
 */


static bool type1_access_ok(unsigned int bus, unsigned int devfn, int reg)
{
	/*
         * This is a workaround for A0 LNC bug where PCI status register does
         * not have new CAP bit set. can not be written by SW either.
         *
         * PCI header type in real LNC indicates a single function device, this
         * will prevent probing other devices under the same function in PCI
         * shim. Therefore, use the header type in shim instead.
         */
	if (reg >= 0x100 || reg == PCI_STATUS || reg == PCI_HEADER_TYPE)
		return false;
	if (bus == 0 && (devfn == PCI_DEVFN(2, 0)
				|| devfn == PCI_DEVFN(0, 0)
				|| devfn == PCI_DEVFN(3, 0)))
		return true;
	return false; /* Langwell on others */
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
Jesse Barnes
47
61.04%
1
20.00%
Björn Helgaas
16
20.78%
1
20.00%
Jacob jun Pan
9
11.69%
1
20.00%
Fengguang Wu
3
3.90%
1
20.00%
Valentina Manea
2
2.60%
1
20.00%
Total
77
100.00%
5
100.00%



static int pci_read(struct pci_bus *bus, unsigned int devfn, int where,
		    int size, u32 *value)
{
	if (type1_access_ok(bus->number, devfn, where))
		return pci_direct_conf1.read(pci_domain_nr(bus), bus->number,
					devfn, where, size, value);
	return raw_pci_ext_ops->read(pci_domain_nr(bus), bus->number,
			      devfn, where, size, value);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
Jesse Barnes
84
100.00%
1
100.00%
Total
84
100.00%
1
100.00%



static int pci_write(struct pci_bus *bus, unsigned int devfn, int where,
		     int size, u32 value)
{
	int offset;

	/*
         * On MRST, there is no PCI ROM BAR, this will cause a subsequent read
         * to ROM BAR return 0 then being ignored.
         */
	if (where == PCI_ROM_ADDRESS)
		return 0;

	/*
         * Devices with fixed BARs need special handling:
         *   - BAR sizing code will save, write ~0, read size, restore
         *   - so writes to fixed BARs need special handling
         *   - other writes to fixed BAR devices should go through mmconfig
         */
	offset = fixed_bar_cap(bus, devfn);
	if (offset &&
	    (where >= PCI_BASE_ADDRESS_0 && where <= PCI_BASE_ADDRESS_5)) {
		return pci_device_update_fixed(bus, devfn, where, size, value,
					       offset);
	}

	/*
         * On Moorestown update both real & mmconfig space
         * Note: early Lincroft silicon can't handle type 1 accesses to
         *       non-existent devices, so just eat the write in that case.
         */
	if (type1_access_ok(bus->number, devfn, where))
		return pci_direct_conf1.write(pci_domain_nr(bus), bus->number,
					      devfn, where, size, value);
	return raw_pci_ext_ops->write(pci_domain_nr(bus), bus->number, devfn,
			       where, size, value);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
Jesse Barnes
138
99.28%
1
50.00%
Valentina Manea
1
0.72%
1
50.00%
Total
139
100.00%
2
100.00%



static int intel_mid_pci_irq_enable(struct pci_dev *dev)
{
	struct irq_alloc_info info;
	int polarity;
	int ret;
	u8 gsi;

	if (dev->irq_managed && dev->irq > 0)
		return 0;

	ret = pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &gsi);
	if (ret < 0) {
		dev_warn(&dev->dev, "Failed to read interrupt line: %d\n", ret);
		return ret;
	}

	switch (intel_mid_identify_cpu()) {
	case INTEL_MID_CPU_CHIP_TANGIER:
		polarity = IOAPIC_POL_HIGH;

		/* Special treatment for IRQ0 */
		if (gsi == 0) {
			/*
                         * Skip HS UART common registers device since it has
                         * IRQ0 assigned and not used by the kernel.
                         */
			if (dev->device == PCI_DEVICE_ID_INTEL_MRFLD_HSU)
				return -EBUSY;
			/*
                         * TNG has IRQ0 assigned to eMMC controller. But there
                         * are also other devices with bogus PCI configuration
                         * that have IRQ0 assigned. This check ensures that
                         * eMMC gets it. The rest of devices still could be
                         * enabled without interrupt line being allocated.
                         */
			if (dev->device != PCI_DEVICE_ID_INTEL_MRFLD_MMC)
				return 0;
		}
		break;
	default:
		polarity = IOAPIC_POL_LOW;
		break;
	}

	ioapic_set_alloc_attr(&info, dev_to_node(&dev->dev), 1, polarity);

	/*
         * MRST only have IOAPIC, the PCI irq lines are 1:1 mapped to
         * IOAPIC RTE entries, so we just enable RTE for the device.
         */
	ret = mp_map_gsi_to_irq(gsi, IOAPIC_MAP_ALLOC, &info);
	if (ret < 0)
		return ret;

	dev->irq = ret;
	dev->irq_managed = 1;

	return 0;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
Andy Shevchenko
98
53.26%
5
38.46%
Jiang Liu
48
26.09%
3
23.08%
Jesse Barnes
19
10.33%
1
7.69%
David Cohen
8
4.35%
1
7.69%
Björn Helgaas
8
4.35%
1
7.69%
Thomas Gleixner
2
1.09%
1
7.69%
Kuppuswamy Sathyanarayanan
1
0.54%
1
7.69%
Total
184
100.00%
13
100.00%



static void intel_mid_pci_irq_disable(struct pci_dev *dev)
{
	if (!mp_should_keep_irq(&dev->dev) && dev->irq_managed &&
	    dev->irq > 0) {
		mp_unmap_irq(dev->irq);
		dev->irq_managed = 0;
	}
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
Jiang Liu
30
63.83%
2
50.00%
Björn Helgaas
17
36.17%
2
50.00%
Total
47
100.00%
4
100.00%


static struct pci_ops intel_mid_pci_ops = {
	.read = pci_read,
	.write = pci_write,
};

/**
 * intel_mid_pci_init - installs intel_mid_pci_ops
 *
 * Moorestown has an interesting PCI implementation (see above).
 * Called when the early platform detection installs it.
 */


int __init intel_mid_pci_init(void)
{
	pr_info("Intel MID platform detected, using MID PCI ops\n");
	pci_mmcfg_late_init();
	pcibios_enable_irq = intel_mid_pci_irq_enable;
	pcibios_disable_irq = intel_mid_pci_irq_disable;
	pci_root_ops = intel_mid_pci_ops;
	pci_soc_mode = 1;
	/* Continue with standard init */
	return 1;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
Jesse Barnes
23
63.89%
1
20.00%
Alan Cox
5
13.89%
1
20.00%
Jiang Liu
4
11.11%
1
20.00%
Kuppuswamy Sathyanarayanan
3
8.33%
1
20.00%
Valentina Manea
1
2.78%
1
20.00%
Total
36
100.00%
5
100.00%

/*
 * Langwell devices are not true PCI devices; they are not subject to 10 ms
 * d3 to d0 delay required by PCI spec.
 */


static void pci_d3delay_fixup(struct pci_dev *dev)
{
	/*
         * PCI fixups are effectively decided compile time. If we have a dual
         * SoC/non-SoC kernel we don't want to mangle d3 on non-SoC devices.
         */
	if (!pci_soc_mode)
		return;
	/*
         * True PCI devices in Lincroft should allow type 1 access, the rest
         * are Langwell fake PCI devices.
         */
	if (type1_access_ok(dev->bus->number, dev->devfn, PCI_DEVICE_ID))
		return;
	dev->d3_delay = 0;
}
Contributors
Person
Tokens
Prop
Commits
CommitProp
Jacob jun Pan
35
81.40%
1
33.33%
Alan Cox
6
13.95%
1
33.33%
Valentina Manea
2
4.65%
1
33.33%
Total
43
100.00%
3
100.00%

DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, pci_d3delay_fixup);



static void mid_power_off_one_device(struct pci_dev *dev)
{
	u16 pmcsr;

	/*
         * Update current state first, otherwise PCI core enforces PCI_D0 in
         * pci_set_power_state() for devices which status was PCI_UNKNOWN.
         */
	pci_read_config_word(dev, dev->pm_cap + PCI_PM_CTRL, &pmcsr);
	dev->current_state = (pci_power_t __force)(pmcsr & PCI_PM_CTRL_STATE_MASK);

	pci_set_power_state(dev, PCI_D3hot);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
Andy Shevchenko
33
66.00%
2
50.00%
Jacob jun Pan
16
32.00%
1
25.00%
Huang Ying
1
2.00%
1
25.00%
Total
50
100.00%
4
100.00%



static void mid_power_off_devices(struct pci_dev *dev)
{
	int id;

	if (!pci_soc_mode)
		return;

	id = intel_mid_pwr_get_lss_id(dev);
	if (id < 0)
		return;

	/*
         * This sets only PMCSR bits. The actual power off will happen in
         * arch/x86/platform/intel-mid/pwr.c.
         */
	mid_power_off_one_device(dev);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
Andy Shevchenko
40
100.00%
2
100.00%
Total
40
100.00%
2
100.00%

DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, mid_power_off_devices);

/*
 * Langwell devices reside at fixed offsets, don't try to move them.
 */


static void pci_fixed_bar_fixup(struct pci_dev *dev)
{
	unsigned long offset;
	u32 size;
	int i;

	if (!pci_soc_mode)
		return;

	/* Must have extended configuration space */
	if (dev->cfg_size < PCIE_CAP_OFFSET + 4)
		return;

	/* Fixup the BAR sizes for fixed BAR devices and make them unmoveable */
	offset = fixed_bar_cap(dev->bus, dev->devfn);
	if (!offset || PCI_DEVFN(2, 0) == dev->devfn ||
	    PCI_DEVFN(2, 2) == dev->devfn)
		return;

	for (i = 0; i < PCI_ROM_RESOURCE; i++) {
		pci_read_config_dword(dev, offset + 8 + (i * 4), &size);
		dev->resource[i].end = dev->resource[i].start + size - 1;
		dev->resource[i].flags |= IORESOURCE_PCI_FIXED;
	}
}
Contributors
Person
Tokens
Prop
Commits
CommitProp
Jesse Barnes
129
87.76%
1
33.33%
H. Peter Anvin
12
8.16%
1
33.33%
Alan Cox
6
4.08%
1
33.33%
Total
147
100.00%
3
100.00%

DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, pci_fixed_bar_fixup);
Overall Contributors
Person
Tokens
Prop
Commits
CommitProp
Jesse Barnes
860
64.47%
1
3.33%
Andy Shevchenko
188
14.09%
8
26.67%
Jacob jun Pan
94
7.05%
4
13.33%
Jiang Liu
82
6.15%
4
13.33%
Björn Helgaas
41
3.07%
3
10.00%
Alan Cox
21
1.57%
1
3.33%
H. Peter Anvin
12
0.90%
1
3.33%
Valentina Manea
11
0.82%
1
3.33%
David Cohen
11
0.82%
1
3.33%
Kuppuswamy Sathyanarayanan
7
0.52%
2
6.67%
Fengguang Wu
3
0.22%
1
3.33%
Thomas Gleixner
2
0.15%
1
3.33%
Greg Kroah-Hartman
1
0.07%
1
3.33%
Huang Ying
1
0.07%
1
3.33%
Total
1334
100.00%
30
100.00%
Directory: arch/x86/pci

Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.