cregit-Linux how code gets into the kernel

Release 4.14 drivers/spi/spi-cadence.c

Directory: drivers/spi
/*
 * Cadence SPI controller driver (master mode only)
 *
 * Copyright (C) 2008 - 2014 Xilinx, Inc.
 *
 * based on Blackfin On-Chip SPI Driver (spi_bfin5xx.c)
 *
 * This program is free software; you can redistribute it and/or modify it under
 * the terms of the GNU General Public License version 2 as published by the
 * Free Software Foundation; either version 2 of the License, or (at your
 * option) any later version.
 */

#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/gpio.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/module.h>
#include <linux/of_irq.h>
#include <linux/of_address.h>
#include <linux/platform_device.h>
#include <linux/pm_runtime.h>
#include <linux/spi/spi.h>

/* Name of this driver */

#define CDNS_SPI_NAME		"cdns-spi"

/* Register offset definitions */

#define CDNS_SPI_CR	0x00 
/* Configuration  Register, RW */

#define CDNS_SPI_ISR	0x04 
/* Interrupt Status Register, RO */

#define CDNS_SPI_IER	0x08 
/* Interrupt Enable Register, WO */

#define CDNS_SPI_IDR	0x0c 
/* Interrupt Disable Register, WO */

#define CDNS_SPI_IMR	0x10 
/* Interrupt Enabled Mask Register, RO */

#define CDNS_SPI_ER	0x14 
/* Enable/Disable Register, RW */

#define CDNS_SPI_DR	0x18 
/* Delay Register, RW */

#define CDNS_SPI_TXD	0x1C 
/* Data Transmit Register, WO */

#define CDNS_SPI_RXD	0x20 
/* Data Receive Register, RO */

#define CDNS_SPI_SICR	0x24 
/* Slave Idle Count Register, RW */

#define CDNS_SPI_THLD	0x28 
/* Transmit FIFO Watermark Register,RW */


#define SPI_AUTOSUSPEND_TIMEOUT		3000
/*
 * SPI Configuration Register bit Masks
 *
 * This register contains various control bits that affect the operation
 * of the SPI controller
 */

#define CDNS_SPI_CR_MANSTRT	0x00010000 
/* Manual TX Start */

#define CDNS_SPI_CR_CPHA		0x00000004 
/* Clock Phase Control */

#define CDNS_SPI_CR_CPOL		0x00000002 
/* Clock Polarity Control */

#define CDNS_SPI_CR_SSCTRL		0x00003C00 
/* Slave Select Mask */

#define CDNS_SPI_CR_PERI_SEL	0x00000200 
/* Peripheral Select Decode */

#define CDNS_SPI_CR_BAUD_DIV	0x00000038 
/* Baud Rate Divisor Mask */

#define CDNS_SPI_CR_MSTREN		0x00000001 
/* Master Enable Mask */

#define CDNS_SPI_CR_MANSTRTEN	0x00008000 
/* Manual TX Enable Mask */

#define CDNS_SPI_CR_SSFORCE	0x00004000 
/* Manual SS Enable Mask */

#define CDNS_SPI_CR_BAUD_DIV_4	0x00000008 
/* Default Baud Div Mask */

#define CDNS_SPI_CR_DEFAULT	(CDNS_SPI_CR_MSTREN | \
                                        CDNS_SPI_CR_SSCTRL | \
                                        CDNS_SPI_CR_SSFORCE | \
                                        CDNS_SPI_CR_BAUD_DIV_4)

/*
 * SPI Configuration Register - Baud rate and slave select
 *
 * These are the values used in the calculation of baud rate divisor and
 * setting the slave select.
 */


#define CDNS_SPI_BAUD_DIV_MAX		7 
/* Baud rate divisor maximum */

#define CDNS_SPI_BAUD_DIV_MIN		1 
/* Baud rate divisor minimum */

#define CDNS_SPI_BAUD_DIV_SHIFT		3 
/* Baud rate divisor shift in CR */

#define CDNS_SPI_SS_SHIFT		10 
/* Slave Select field shift in CR */

#define CDNS_SPI_SS0			0x1 
/* Slave Select zero */

/*
 * SPI Interrupt Registers bit Masks
 *
 * All the four interrupt registers (Status/Mask/Enable/Disable) have the same
 * bit definitions.
 */

#define CDNS_SPI_IXR_TXOW	0x00000004 
/* SPI TX FIFO Overwater */

#define CDNS_SPI_IXR_MODF	0x00000002 
/* SPI Mode Fault */

#define CDNS_SPI_IXR_RXNEMTY 0x00000010 
/* SPI RX FIFO Not Empty */

#define CDNS_SPI_IXR_DEFAULT	(CDNS_SPI_IXR_TXOW | \
                                        CDNS_SPI_IXR_MODF)

#define CDNS_SPI_IXR_TXFULL	0x00000008 
/* SPI TX Full */

#define CDNS_SPI_IXR_ALL	0x0000007F 
/* SPI all interrupts */

/*
 * SPI Enable Register bit Masks
 *
 * This register is used to enable or disable the SPI controller
 */

#define CDNS_SPI_ER_ENABLE	0x00000001 
/* SPI Enable Bit Mask */

#define CDNS_SPI_ER_DISABLE	0x0 
/* SPI Disable Bit Mask */

/* SPI FIFO depth in bytes */

#define CDNS_SPI_FIFO_DEPTH	128

/* Default number of chip select lines */

#define CDNS_SPI_DEFAULT_NUM_CS		4

/**
 * struct cdns_spi - This definition defines spi driver instance
 * @regs:               Virtual address of the SPI controller registers
 * @ref_clk:            Pointer to the peripheral clock
 * @pclk:               Pointer to the APB clock
 * @speed_hz:           Current SPI bus clock speed in Hz
 * @txbuf:              Pointer to the TX buffer
 * @rxbuf:              Pointer to the RX buffer
 * @tx_bytes:           Number of bytes left to transfer
 * @rx_bytes:           Number of bytes requested
 * @dev_busy:           Device busy flag
 * @is_decoded_cs:      Flag for decoder property set or not
 */

struct cdns_spi {
	
void __iomem *regs;
	
struct clk *ref_clk;
	
struct clk *pclk;
	
u32 speed_hz;
	
const u8 *txbuf;
	
u8 *rxbuf;
	
int tx_bytes;
	
int rx_bytes;
	
u8 dev_busy;
	
u32 is_decoded_cs;
};


struct cdns_spi_device_data {
	
bool gpio_requested;
};

/* Macros for the SPI controller read/write */

static inline u32 cdns_spi_read(struct cdns_spi *xspi, u32 offset) { return readl_relaxed(xspi->regs + offset); }

Contributors

PersonTokensPropCommitsCommitProp
Harini Katakam25100.00%1100.00%
Total25100.00%1100.00%


static inline void cdns_spi_write(struct cdns_spi *xspi, u32 offset, u32 val) { writel_relaxed(val, xspi->regs + offset); }

Contributors

PersonTokensPropCommitsCommitProp
Harini Katakam29100.00%1100.00%
Total29100.00%1100.00%

/** * cdns_spi_init_hw - Initialize the hardware and configure the SPI controller * @xspi: Pointer to the cdns_spi structure * * On reset the SPI controller is configured to be in master mode, baud rate * divisor is set to 4, threshold value for TX FIFO not full interrupt is set * to 1 and size of the word to be transferred as 8 bit. * This function initializes the SPI controller to disable and clear all the * interrupts, enable manual slave select and manual start, deselect all the * chip select lines, and enable the SPI controller. */
static void cdns_spi_init_hw(struct cdns_spi *xspi) { u32 ctrl_reg = CDNS_SPI_CR_DEFAULT; if (xspi->is_decoded_cs) ctrl_reg |= CDNS_SPI_CR_PERI_SEL; cdns_spi_write(xspi, CDNS_SPI_ER, CDNS_SPI_ER_DISABLE); cdns_spi_write(xspi, CDNS_SPI_IDR, CDNS_SPI_IXR_ALL); /* Clear the RX FIFO */ while (cdns_spi_read(xspi, CDNS_SPI_ISR) & CDNS_SPI_IXR_RXNEMTY) cdns_spi_read(xspi, CDNS_SPI_RXD); cdns_spi_write(xspi, CDNS_SPI_ISR, CDNS_SPI_IXR_ALL); cdns_spi_write(xspi, CDNS_SPI_CR, ctrl_reg); cdns_spi_write(xspi, CDNS_SPI_ER, CDNS_SPI_ER_ENABLE); }

Contributors

PersonTokensPropCommitsCommitProp
Harini Katakam6268.89%133.33%
Lars-Peter Clausen1415.56%133.33%
Shubhrajyoti Datta1415.56%133.33%
Total90100.00%3100.00%

/** * cdns_spi_chipselect - Select or deselect the chip select line * @spi: Pointer to the spi_device structure * @is_high: Select(0) or deselect (1) the chip select line */
static void cdns_spi_chipselect(struct spi_device *spi, bool is_high) { struct cdns_spi *xspi = spi_master_get_devdata(spi->master); u32 ctrl_reg; ctrl_reg = cdns_spi_read(xspi, CDNS_SPI_CR); if (is_high) { /* Deselect the slave */ ctrl_reg |= CDNS_SPI_CR_SSCTRL; } else { /* Select the slave */ ctrl_reg &= ~CDNS_SPI_CR_SSCTRL; if (!(xspi->is_decoded_cs)) ctrl_reg |= ((~(CDNS_SPI_SS0 << spi->chip_select)) << CDNS_SPI_SS_SHIFT) & CDNS_SPI_CR_SSCTRL; else ctrl_reg |= (spi->chip_select << CDNS_SPI_SS_SHIFT) & CDNS_SPI_CR_SSCTRL; } cdns_spi_write(xspi, CDNS_SPI_CR, ctrl_reg); }

Contributors

PersonTokensPropCommitsCommitProp
Harini Katakam10294.44%150.00%
Shubhrajyoti Datta65.56%150.00%
Total108100.00%2100.00%

/** * cdns_spi_config_clock_mode - Sets clock polarity and phase * @spi: Pointer to the spi_device structure * * Sets the requested clock polarity and phase. */
static void cdns_spi_config_clock_mode(struct spi_device *spi) { struct cdns_spi *xspi = spi_master_get_devdata(spi->master); u32 ctrl_reg, new_ctrl_reg; new_ctrl_reg = cdns_spi_read(xspi, CDNS_SPI_CR); ctrl_reg = new_ctrl_reg; /* Set the SPI clock phase and clock polarity */ new_ctrl_reg &= ~(CDNS_SPI_CR_CPHA | CDNS_SPI_CR_CPOL); if (spi->mode & SPI_CPHA) new_ctrl_reg |= CDNS_SPI_CR_CPHA; if (spi->mode & SPI_CPOL) new_ctrl_reg |= CDNS_SPI_CR_CPOL; if (new_ctrl_reg != ctrl_reg) { /* * Just writing the CR register does not seem to apply the clock * setting changes. This is problematic when changing the clock * polarity as it will cause the SPI slave to see spurious clock * transitions. To workaround the issue toggle the ER register. */ cdns_spi_write(xspi, CDNS_SPI_ER, CDNS_SPI_ER_DISABLE); cdns_spi_write(xspi, CDNS_SPI_CR, new_ctrl_reg); cdns_spi_write(xspi, CDNS_SPI_ER, CDNS_SPI_ER_ENABLE); } }

Contributors

PersonTokensPropCommitsCommitProp
Harini Katakam6659.46%125.00%
Lars-Peter Clausen3127.93%125.00%
Shubhrajyoti Datta1412.61%250.00%
Total111100.00%4100.00%

/** * cdns_spi_config_clock_freq - Sets clock frequency * @spi: Pointer to the spi_device structure * @transfer: Pointer to the spi_transfer structure which provides * information about next transfer setup parameters * * Sets the requested clock frequency. * Note: If the requested frequency is not an exact match with what can be * obtained using the prescalar value the driver sets the clock frequency which * is lower than the requested frequency (maximum lower) for the transfer. If * the requested frequency is higher or lower than that is supported by the SPI * controller the driver will set the highest or lowest frequency supported by * controller. */
static void cdns_spi_config_clock_freq(struct spi_device *spi, struct spi_transfer *transfer) { struct cdns_spi *xspi = spi_master_get_devdata(spi->master); u32 ctrl_reg, baud_rate_val; unsigned long frequency; frequency = clk_get_rate(xspi->ref_clk); ctrl_reg = cdns_spi_read(xspi, CDNS_SPI_CR); /* Set the clock frequency */ if (xspi->speed_hz != transfer->speed_hz) { /* first valid value is 1 */ baud_rate_val = CDNS_SPI_BAUD_DIV_MIN; while ((baud_rate_val < CDNS_SPI_BAUD_DIV_MAX) && (frequency / (2 << baud_rate_val)) > transfer->speed_hz) baud_rate_val++; ctrl_reg &= ~CDNS_SPI_CR_BAUD_DIV; ctrl_reg |= baud_rate_val << CDNS_SPI_BAUD_DIV_SHIFT; xspi->speed_hz = frequency / (2 << baud_rate_val); } cdns_spi_write(xspi, CDNS_SPI_CR, ctrl_reg); }

Contributors

PersonTokensPropCommitsCommitProp
Harini Katakam12797.69%150.00%
Shubhrajyoti Datta32.31%150.00%
Total130100.00%2100.00%

/** * cdns_spi_setup_transfer - Configure SPI controller for specified transfer * @spi: Pointer to the spi_device structure * @transfer: Pointer to the spi_transfer structure which provides * information about next transfer setup parameters * * Sets the operational mode of SPI controller for the next SPI transfer and * sets the requested clock frequency. * * Return: Always 0 */
static int cdns_spi_setup_transfer(struct spi_device *spi, struct spi_transfer *transfer) { struct cdns_spi *xspi = spi_master_get_devdata(spi->master); cdns_spi_config_clock_freq(spi, transfer); dev_dbg(&spi->dev, "%s, mode %d, %u bits/w, %u clock speed\n", __func__, spi->mode, spi->bits_per_word, xspi->speed_hz); return 0; }

Contributors

PersonTokensPropCommitsCommitProp
Harini Katakam62100.00%1100.00%
Total62100.00%1100.00%

/** * cdns_spi_fill_tx_fifo - Fills the TX FIFO with as many bytes as possible * @xspi: Pointer to the cdns_spi structure */
static void cdns_spi_fill_tx_fifo(struct cdns_spi *xspi) { unsigned long trans_cnt = 0; while ((trans_cnt < CDNS_SPI_FIFO_DEPTH) && (xspi->tx_bytes > 0)) { if (xspi->txbuf) cdns_spi_write(xspi, CDNS_SPI_TXD, *xspi->txbuf++); else cdns_spi_write(xspi, CDNS_SPI_TXD, 0); xspi->tx_bytes--; trans_cnt++; } }

Contributors

PersonTokensPropCommitsCommitProp
Harini Katakam7097.22%150.00%
Shubhrajyoti Datta22.78%150.00%
Total72100.00%2100.00%

/** * cdns_spi_irq - Interrupt service routine of the SPI controller * @irq: IRQ number * @dev_id: Pointer to the xspi structure * * This function handles TX empty and Mode Fault interrupts only. * On TX empty interrupt this function reads the received data from RX FIFO and * fills the TX FIFO if there is any data remaining to be transferred. * On Mode Fault interrupt this function indicates that transfer is completed, * the SPI subsystem will identify the error as the remaining bytes to be * transferred is non-zero. * * Return: IRQ_HANDLED when handled; IRQ_NONE otherwise. */
static irqreturn_t cdns_spi_irq(int irq, void *dev_id) { struct spi_master *master = dev_id; struct cdns_spi *xspi = spi_master_get_devdata(master); u32 intr_status, status; status = IRQ_NONE; intr_status = cdns_spi_read(xspi, CDNS_SPI_ISR); cdns_spi_write(xspi, CDNS_SPI_ISR, intr_status); if (intr_status & CDNS_SPI_IXR_MODF) { /* Indicate that transfer is completed, the SPI subsystem will * identify the error as the remaining bytes to be * transferred is non-zero */ cdns_spi_write(xspi, CDNS_SPI_IDR, CDNS_SPI_IXR_DEFAULT); spi_finalize_current_transfer(master); status = IRQ_HANDLED; } else if (intr_status & CDNS_SPI_IXR_TXOW) { unsigned long trans_cnt; trans_cnt = xspi->rx_bytes - xspi->tx_bytes; /* Read out the data from the RX FIFO */ while (trans_cnt) { u8 data; data = cdns_spi_read(xspi, CDNS_SPI_RXD); if (xspi->rxbuf) *xspi->rxbuf++ = data; xspi->rx_bytes--; trans_cnt--; } if (xspi->tx_bytes) { /* There is more data to send */ cdns_spi_fill_tx_fifo(xspi); } else { /* Transfer is completed */ cdns_spi_write(xspi, CDNS_SPI_IDR, CDNS_SPI_IXR_DEFAULT); spi_finalize_current_transfer(master); } status = IRQ_HANDLED; } return status; }

Contributors

PersonTokensPropCommitsCommitProp
Harini Katakam17895.19%150.00%
Shubhrajyoti Datta94.81%150.00%
Total187100.00%2100.00%


static int cdns_prepare_message(struct spi_master *master, struct spi_message *msg) { cdns_spi_config_clock_mode(msg->spi); return 0; }

Contributors

PersonTokensPropCommitsCommitProp
Lars-Peter Clausen26100.00%1100.00%
Total26100.00%1100.00%

/** * cdns_transfer_one - Initiates the SPI transfer * @master: Pointer to spi_master structure * @spi: Pointer to the spi_device structure * @transfer: Pointer to the spi_transfer structure which provides * information about next transfer parameters * * This function fills the TX FIFO, starts the SPI transfer and * returns a positive transfer count so that core will wait for completion. * * Return: Number of bytes transferred in the last transfer */
static int cdns_transfer_one(struct spi_master *master, struct spi_device *spi, struct spi_transfer *transfer) { struct cdns_spi *xspi = spi_master_get_devdata(master); xspi->txbuf = transfer->tx_buf; xspi->rxbuf = transfer->rx_buf; xspi->tx_bytes = transfer->len; xspi->rx_bytes = transfer->len; cdns_spi_setup_transfer(spi, transfer); cdns_spi_fill_tx_fifo(xspi); cdns_spi_write(xspi, CDNS_SPI_IER, CDNS_SPI_IXR_DEFAULT); return transfer->len; }

Contributors

PersonTokensPropCommitsCommitProp
Harini Katakam8797.75%150.00%
Shubhrajyoti Datta22.25%150.00%
Total89100.00%2100.00%

/** * cdns_prepare_transfer_hardware - Prepares hardware for transfer. * @master: Pointer to the spi_master structure which provides * information about the controller. * * This function enables SPI master controller. * * Return: 0 always */
static int cdns_prepare_transfer_hardware(struct spi_master *master) { struct cdns_spi *xspi = spi_master_get_devdata(master); cdns_spi_write(xspi, CDNS_SPI_ER, CDNS_SPI_ER_ENABLE); return 0; }

Contributors

PersonTokensPropCommitsCommitProp
Harini Katakam3193.94%150.00%
Shubhrajyoti Datta26.06%150.00%
Total33100.00%2100.00%

/** * cdns_unprepare_transfer_hardware - Relaxes hardware after transfer * @master: Pointer to the spi_master structure which provides * information about the controller. * * This function disables the SPI master controller. * * Return: 0 always */
static int cdns_unprepare_transfer_hardware(struct spi_master *master) { struct cdns_spi *xspi = spi_master_get_devdata(master); cdns_spi_write(xspi, CDNS_SPI_ER, CDNS_SPI_ER_DISABLE); return 0; }

Contributors

PersonTokensPropCommitsCommitProp
Harini Katakam3193.94%150.00%
Shubhrajyoti Datta26.06%150.00%
Total33100.00%2100.00%


static int cdns_spi_setup(struct spi_device *spi) { int ret = -EINVAL; struct cdns_spi_device_data *cdns_spi_data = spi_get_ctldata(spi); /* this is a pin managed by the controller, leave it alone */ if (spi->cs_gpio == -ENOENT) return 0; /* this seems to be the first time we're here */ if (!cdns_spi_data) { cdns_spi_data = kzalloc(sizeof(*cdns_spi_data), GFP_KERNEL); if (!cdns_spi_data) return -ENOMEM; cdns_spi_data->gpio_requested = false; spi_set_ctldata(spi, cdns_spi_data); } /* if we haven't done so, grab the gpio */ if (!cdns_spi_data->gpio_requested && gpio_is_valid(spi->cs_gpio)) { ret = gpio_request_one(spi->cs_gpio, (spi->mode & SPI_CS_HIGH) ? GPIOF_OUT_INIT_LOW : GPIOF_OUT_INIT_HIGH, dev_name(&spi->dev)); if (ret) dev_err(&spi->dev, "can't request chipselect gpio %d\n", spi->cs_gpio); else cdns_spi_data->gpio_requested = true; } else { if (gpio_is_valid(spi->cs_gpio)) { int mode = ((spi->mode & SPI_CS_HIGH) ? GPIOF_OUT_INIT_LOW : GPIOF_OUT_INIT_HIGH); ret = gpio_direction_output(spi->cs_gpio, mode); if (ret) dev_err(&spi->dev, "chipselect gpio %d setup failed (%d)\n", spi->cs_gpio, ret); } } return ret; }

Contributors

PersonTokensPropCommitsCommitProp
Moritz Fischer219100.00%1100.00%
Total219100.00%1100.00%


static void cdns_spi_cleanup(struct spi_device *spi) { struct cdns_spi_device_data *cdns_spi_data = spi_get_ctldata(spi); if (cdns_spi_data) { if (cdns_spi_data->gpio_requested) gpio_free(spi->cs_gpio); kfree(cdns_spi_data); spi_set_ctldata(spi, NULL); } }

Contributors

PersonTokensPropCommitsCommitProp
Moritz Fischer52100.00%1100.00%
Total52100.00%1100.00%

/** * cdns_spi_probe - Probe method for the SPI driver * @pdev: Pointer to the platform_device structure * * This function initializes the driver data structures and the hardware. * * Return: 0 on success and error value on error */
static int cdns_spi_probe(struct platform_device *pdev) { int ret = 0, irq; struct spi_master *master; struct cdns_spi *xspi; struct resource *res; u32 num_cs; master = spi_alloc_master(&pdev->dev, sizeof(*xspi)); if (!master) return -ENOMEM; xspi = spi_master_get_devdata(master); master->dev.of_node = pdev->dev.of_node; platform_set_drvdata(pdev, master); res = platform_get_resource(pdev, IORESOURCE_MEM, 0); xspi->regs = devm_ioremap_resource(&pdev->dev, res); if (IS_ERR(xspi->regs)) { ret = PTR_ERR(xspi->regs); goto remove_master; } xspi->pclk = devm_clk_get(&pdev->dev, "pclk"); if (IS_ERR(xspi->pclk)) { dev_err(&pdev->dev, "pclk clock not found.\n"); ret = PTR_ERR(xspi->pclk); goto remove_master; } xspi->ref_clk = devm_clk_get(&pdev->dev, "ref_clk"); if (IS_ERR(xspi->ref_clk)) { dev_err(&pdev->dev, "ref_clk clock not found.\n"); ret = PTR_ERR(xspi->ref_clk); goto remove_master; } ret = clk_prepare_enable(xspi->pclk); if (ret) { dev_err(&pdev->dev, "Unable to enable APB clock.\n"); goto remove_master; } ret = clk_prepare_enable(xspi->ref_clk); if (ret) { dev_err(&pdev->dev, "Unable to enable device clock.\n"); goto clk_dis_apb; } pm_runtime_use_autosuspend(&pdev->dev); pm_runtime_set_autosuspend_delay(&pdev->dev, SPI_AUTOSUSPEND_TIMEOUT); pm_runtime_set_active(&pdev->dev); pm_runtime_enable(&pdev->dev); ret = of_property_read_u32(pdev->dev.of_node, "num-cs", &num_cs); if (ret < 0) master->num_chipselect = CDNS_SPI_DEFAULT_NUM_CS; else master->num_chipselect = num_cs; ret = of_property_read_u32(pdev->dev.of_node, "is-decoded-cs", &xspi->is_decoded_cs); if (ret < 0) xspi->is_decoded_cs = 0; /* SPI controller initializations */ cdns_spi_init_hw(xspi); pm_runtime_mark_last_busy(&pdev->dev); pm_runtime_put_autosuspend(&pdev->dev); irq = platform_get_irq(pdev, 0); if (irq <= 0) { ret = -ENXIO; dev_err(&pdev->dev, "irq number is invalid\n"); goto clk_dis_all; } ret = devm_request_irq(&pdev->dev, irq, cdns_spi_irq, 0, pdev->name, master); if (ret != 0) { ret = -ENXIO; dev_err(&pdev->dev, "request_irq failed\n"); goto clk_dis_all; } master->prepare_transfer_hardware = cdns_prepare_transfer_hardware; master->prepare_message = cdns_prepare_message; master->transfer_one = cdns_transfer_one; master->unprepare_transfer_hardware = cdns_unprepare_transfer_hardware; master->set_cs = cdns_spi_chipselect; master->setup = cdns_spi_setup; master->cleanup = cdns_spi_cleanup; master->auto_runtime_pm = true; master->mode_bits = SPI_CPOL | SPI_CPHA; /* Set to default valid value */ master->max_speed_hz = clk_get_rate(xspi->ref_clk) / 4; xspi->speed_hz = master->max_speed_hz; master->bits_per_word_mask = SPI_BPW_MASK(8); ret = spi_register_master(master); if (ret) { dev_err(&pdev->dev, "spi_register_master failed\n"); goto clk_dis_all; } return ret; clk_dis_all: pm_runtime_set_suspended(&pdev->dev); pm_runtime_disable(&pdev->dev); clk_disable_unprepare(xspi->ref_clk); clk_dis_apb: clk_disable_unprepare(xspi->pclk); remove_master: spi_master_put(master); return ret; }

Contributors

PersonTokensPropCommitsCommitProp
Harini Katakam49175.65%112.50%
Shubhrajyoti Datta6910.63%337.50%
Paul Cercueil6510.02%112.50%
Moritz Fischer121.85%112.50%
Naga Sureshkumar Relli60.92%112.50%
Lars-Peter Clausen60.92%112.50%
Total649100.00%8100.00%

/** * cdns_spi_remove - Remove method for the SPI driver * @pdev: Pointer to the platform_device structure * * This function is called if a device is physically removed from the system or * if the driver module is being unloaded. It frees all resources allocated to * the device. * * Return: 0 on success and error value on error */
static int cdns_spi_remove(struct platform_device *pdev) { struct spi_master *master = platform_get_drvdata(pdev); struct cdns_spi *xspi = spi_master_get_devdata(master); cdns_spi_write(xspi, CDNS_SPI_ER, CDNS_SPI_ER_DISABLE); clk_disable_unprepare(xspi->ref_clk); clk_disable_unprepare(xspi->pclk); pm_runtime_set_suspended(&pdev->dev); pm_runtime_disable(&pdev->dev); spi_unregister_master(master); return 0; }

Contributors

PersonTokensPropCommitsCommitProp
Harini Katakam6076.92%133.33%
Shubhrajyoti Datta1823.08%266.67%
Total78100.00%3100.00%

/** * cdns_spi_suspend - Suspend method for the SPI driver * @dev: Address of the platform_device structure * * This function disables the SPI controller and * changes the driver state to "suspend" * * Return: 0 on success and error value on error */
static int __maybe_unused cdns_spi_suspend(struct device *dev) { struct platform_device *pdev = to_platform_device(dev); struct spi_master *master = platform_get_drvdata(pdev); return spi_master_suspend(master); }

Contributors

PersonTokensPropCommitsCommitProp
Harini Katakam3694.74%133.33%
Shubhrajyoti Datta12.63%133.33%
Geliang Tang12.63%133.33%
Total38100.00%3100.00%

/** * cdns_spi_resume - Resume method for the SPI driver * @dev: Address of the platform_device structure * * This function changes the driver state to "ready" * * Return: 0 on success and error value on error */
static int __maybe_unused cdns_spi_resume(struct device *dev) { struct platform_device *pdev = to_platform_device(dev); struct spi_master *master = platform_get_drvdata(pdev); struct cdns_spi *xspi = spi_master_get_devdata(master); cdns_spi_init_hw(xspi); return spi_master_resume(master); }

Contributors

PersonTokensPropCommitsCommitProp
Harini Katakam3667.92%125.00%
Shubhrajyoti Datta1630.19%250.00%
Geliang Tang11.89%125.00%
Total53100.00%4100.00%

/** * cdns_spi_runtime_resume - Runtime resume method for the SPI driver * @dev: Address of the platform_device structure * * This function enables the clocks * * Return: 0 on success and error value on error */
static int __maybe_unused cnds_runtime_resume(struct device *dev) { struct spi_master *master = dev_get_drvdata(dev); struct cdns_spi *xspi = spi_master_get_devdata(master); int ret; ret = clk_prepare_enable(xspi->pclk); if (ret) { dev_err(dev, "Cannot enable APB clock.\n"); return ret; } ret = clk_prepare_enable(xspi->ref_clk); if (ret) { dev_err(dev, "Cannot enable device clock.\n"); clk_disable(xspi->pclk); return ret; } return 0; }

Contributors

PersonTokensPropCommitsCommitProp
Shubhrajyoti Datta8892.63%133.33%
Harini Katakam66.32%133.33%
Arnd Bergmann11.05%133.33%
Total95100.00%3100.00%

/** * cdns_spi_runtime_suspend - Runtime suspend method for the SPI driver * @dev: Address of the platform_device structure * * This function disables the clocks * * Return: Always 0 */
static int __maybe_unused cnds_runtime_suspend(struct device *dev) { struct spi_master *master = dev_get_drvdata(dev); struct cdns_spi *xspi = spi_master_get_devdata(master); clk_disable_unprepare(xspi->ref_clk); clk_disable_unprepare(xspi->pclk); return 0; }

Contributors

PersonTokensPropCommitsCommitProp
Shubhrajyoti Datta4897.96%150.00%
Arnd Bergmann12.04%150.00%
Total49100.00%2100.00%

static const struct dev_pm_ops cdns_spi_dev_pm_ops = { SET_RUNTIME_PM_OPS(cnds_runtime_suspend, cnds_runtime_resume, NULL) SET_SYSTEM_SLEEP_PM_OPS(cdns_spi_suspend, cdns_spi_resume) }; static const struct of_device_id cdns_spi_of_match[] = { { .compatible = "xlnx,zynq-spi-r1p6" }, { .compatible = "cdns,spi-r1p6" }, { /* end of table */ } }; MODULE_DEVICE_TABLE(of, cdns_spi_of_match); /* cdns_spi_driver - This structure defines the SPI subsystem platform driver */ static struct platform_driver cdns_spi_driver = { .probe = cdns_spi_probe, .remove = cdns_spi_remove, .driver = { .name = CDNS_SPI_NAME, .of_match_table = cdns_spi_of_match, .pm = &cdns_spi_dev_pm_ops, }, }; module_platform_driver(cdns_spi_driver); MODULE_AUTHOR("Xilinx, Inc."); MODULE_DESCRIPTION("Cadence SPI driver"); MODULE_LICENSE("GPL");

Overall Contributors

PersonTokensPropCommitsCommitProp
Harini Katakam183469.34%15.56%
Shubhrajyoti Datta36013.61%844.44%
Moritz Fischer29411.12%15.56%
Lars-Peter Clausen813.06%316.67%
Paul Cercueil652.46%15.56%
Naga Sureshkumar Relli60.23%15.56%
Arnd Bergmann20.08%15.56%
Geliang Tang20.08%15.56%
Jingoo Han10.04%15.56%
Total2645100.00%18100.00%
Directory: drivers/spi
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.
Created with cregit.