Author | Tokens | Token Proportion | Commits | Commit Proportion |
---|---|---|---|---|
Peter Korsgaard | 2588 | 87.02% | 20 | 40.82% |
Fengguang Wu | 92 | 3.09% | 4 | 8.16% |
Stephen Hemminger | 56 | 1.88% | 2 | 4.08% |
Jon Dowland | 40 | 1.34% | 1 | 2.04% |
Joe Perches | 35 | 1.18% | 1 | 2.04% |
Hideaki Yoshifuji / 吉藤英明 | 20 | 0.67% | 1 | 2.04% |
Janusz Krzysztofik | 20 | 0.67% | 1 | 2.04% |
Shahar Havivi | 20 | 0.67% | 1 | 2.04% |
Jiri Pirko | 18 | 0.61% | 3 | 6.12% |
Ming Lei | 14 | 0.47% | 2 | 4.08% |
David Decotigny | 12 | 0.40% | 1 | 2.04% |
Tushar Behera | 11 | 0.37% | 1 | 2.04% |
Herbert Xu | 10 | 0.34% | 1 | 2.04% |
Philippe Reynes | 6 | 0.20% | 1 | 2.04% |
Al Viro | 6 | 0.20% | 1 | 2.04% |
Sarah Sharp | 5 | 0.17% | 1 | 2.04% |
Greg Ungerer | 5 | 0.17% | 1 | 2.04% |
Randy Dunlap | 4 | 0.13% | 1 | 2.04% |
Simon Que | 4 | 0.13% | 1 | 2.04% |
Tejun Heo | 3 | 0.10% | 1 | 2.04% |
Greg Kroah-Hartman | 2 | 0.07% | 1 | 2.04% |
Ben Hutchings | 2 | 0.07% | 1 | 2.04% |
Jussi Kivilinna | 1 | 0.03% | 1 | 2.04% |
Total | 2974 | 49 |
/* * Davicom DM96xx USB 10/100Mbps ethernet devices * * Peter Korsgaard <jacmet@sunsite.dk> * * This file is licensed under the terms of the GNU General Public License * version 2. This program is licensed "as is" without any warranty of any * kind, whether express or implied. */ //#define DEBUG #include <linux/module.h> #include <linux/sched.h> #include <linux/stddef.h> #include <linux/netdevice.h> #include <linux/etherdevice.h> #include <linux/ethtool.h> #include <linux/mii.h> #include <linux/usb.h> #include <linux/crc32.h> #include <linux/usb/usbnet.h> #include <linux/slab.h> /* datasheet: http://ptm2.cc.utu.fi/ftp/network/cards/DM9601/From_NET/DM9601-DS-P01-930914.pdf */ /* control requests */ #define DM_READ_REGS 0x00 #define DM_WRITE_REGS 0x01 #define DM_READ_MEMS 0x02 #define DM_WRITE_REG 0x03 #define DM_WRITE_MEMS 0x05 #define DM_WRITE_MEM 0x07 /* registers */ #define DM_NET_CTRL 0x00 #define DM_RX_CTRL 0x05 #define DM_SHARED_CTRL 0x0b #define DM_SHARED_ADDR 0x0c #define DM_SHARED_DATA 0x0d /* low + high */ #define DM_PHY_ADDR 0x10 /* 6 bytes */ #define DM_MCAST_ADDR 0x16 /* 8 bytes */ #define DM_GPR_CTRL 0x1e #define DM_GPR_DATA 0x1f #define DM_CHIP_ID 0x2c #define DM_MODE_CTRL 0x91 /* only on dm9620 */ /* chip id values */ #define ID_DM9601 0 #define ID_DM9620 1 #define DM_MAX_MCAST 64 #define DM_MCAST_SIZE 8 #define DM_EEPROM_LEN 256 #define DM_TX_OVERHEAD 2 /* 2 byte header */ #define DM_RX_OVERHEAD 7 /* 3 byte header + 4 byte crc tail */ #define DM_TIMEOUT 1000 static int dm_read(struct usbnet *dev, u8 reg, u16 length, void *data) { int err; err = usbnet_read_cmd(dev, DM_READ_REGS, USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE, 0, reg, data, length); if(err != length && err >= 0) err = -EINVAL; return err; } static int dm_read_reg(struct usbnet *dev, u8 reg, u8 *value) { return dm_read(dev, reg, 1, value); } static int dm_write(struct usbnet *dev, u8 reg, u16 length, void *data) { int err; err = usbnet_write_cmd(dev, DM_WRITE_REGS, USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE, 0, reg, data, length); if (err >= 0 && err < length) err = -EINVAL; return err; } static int dm_write_reg(struct usbnet *dev, u8 reg, u8 value) { return usbnet_write_cmd(dev, DM_WRITE_REG, USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE, value, reg, NULL, 0); } static void dm_write_async(struct usbnet *dev, u8 reg, u16 length, void *data) { usbnet_write_cmd_async(dev, DM_WRITE_REGS, USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE, 0, reg, data, length); } static void dm_write_reg_async(struct usbnet *dev, u8 reg, u8 value) { usbnet_write_cmd_async(dev, DM_WRITE_REG, USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE, value, reg, NULL, 0); } static int dm_read_shared_word(struct usbnet *dev, int phy, u8 reg, __le16 *value) { int ret, i; mutex_lock(&dev->phy_mutex); dm_write_reg(dev, DM_SHARED_ADDR, phy ? (reg | 0x40) : reg); dm_write_reg(dev, DM_SHARED_CTRL, phy ? 0xc : 0x4); for (i = 0; i < DM_TIMEOUT; i++) { u8 tmp = 0; udelay(1); ret = dm_read_reg(dev, DM_SHARED_CTRL, &tmp); if (ret < 0) goto out; /* ready */ if ((tmp & 1) == 0) break; } if (i == DM_TIMEOUT) { netdev_err(dev->net, "%s read timed out!\n", phy ? "phy" : "eeprom"); ret = -EIO; goto out; } dm_write_reg(dev, DM_SHARED_CTRL, 0x0); ret = dm_read(dev, DM_SHARED_DATA, 2, value); netdev_dbg(dev->net, "read shared %d 0x%02x returned 0x%04x, %d\n", phy, reg, *value, ret); out: mutex_unlock(&dev->phy_mutex); return ret; } static int dm_write_shared_word(struct usbnet *dev, int phy, u8 reg, __le16 value) { int ret, i; mutex_lock(&dev->phy_mutex); ret = dm_write(dev, DM_SHARED_DATA, 2, &value); if (ret < 0) goto out; dm_write_reg(dev, DM_SHARED_ADDR, phy ? (reg | 0x40) : reg); dm_write_reg(dev, DM_SHARED_CTRL, phy ? 0x1a : 0x12); for (i = 0; i < DM_TIMEOUT; i++) { u8 tmp = 0; udelay(1); ret = dm_read_reg(dev, DM_SHARED_CTRL, &tmp); if (ret < 0) goto out; /* ready */ if ((tmp & 1) == 0) break; } if (i == DM_TIMEOUT) { netdev_err(dev->net, "%s write timed out!\n", phy ? "phy" : "eeprom"); ret = -EIO; goto out; } dm_write_reg(dev, DM_SHARED_CTRL, 0x0); out: mutex_unlock(&dev->phy_mutex); return ret; } static int dm_read_eeprom_word(struct usbnet *dev, u8 offset, void *value) { return dm_read_shared_word(dev, 0, offset, value); } static int dm9601_get_eeprom_len(struct net_device *dev) { return DM_EEPROM_LEN; } static int dm9601_get_eeprom(struct net_device *net, struct ethtool_eeprom *eeprom, u8 * data) { struct usbnet *dev = netdev_priv(net); __le16 *ebuf = (__le16 *) data; int i; /* access is 16bit */ if ((eeprom->offset % 2) || (eeprom->len % 2)) return -EINVAL; for (i = 0; i < eeprom->len / 2; i++) { if (dm_read_eeprom_word(dev, eeprom->offset / 2 + i, &ebuf[i]) < 0) return -EINVAL; } return 0; } static int dm9601_mdio_read(struct net_device *netdev, int phy_id, int loc) { struct usbnet *dev = netdev_priv(netdev); __le16 res; if (phy_id) { netdev_dbg(dev->net, "Only internal phy supported\n"); return 0; } dm_read_shared_word(dev, 1, loc, &res); netdev_dbg(dev->net, "dm9601_mdio_read() phy_id=0x%02x, loc=0x%02x, returns=0x%04x\n", phy_id, loc, le16_to_cpu(res)); return le16_to_cpu(res); } static void dm9601_mdio_write(struct net_device *netdev, int phy_id, int loc, int val) { struct usbnet *dev = netdev_priv(netdev); __le16 res = cpu_to_le16(val); if (phy_id) { netdev_dbg(dev->net, "Only internal phy supported\n"); return; } netdev_dbg(dev->net, "dm9601_mdio_write() phy_id=0x%02x, loc=0x%02x, val=0x%04x\n", phy_id, loc, val); dm_write_shared_word(dev, 1, loc, res); } static void dm9601_get_drvinfo(struct net_device *net, struct ethtool_drvinfo *info) { /* Inherit standard device info */ usbnet_get_drvinfo(net, info); } static u32 dm9601_get_link(struct net_device *net) { struct usbnet *dev = netdev_priv(net); return mii_link_ok(&dev->mii); } static int dm9601_ioctl(struct net_device *net, struct ifreq *rq, int cmd) { struct usbnet *dev = netdev_priv(net); return generic_mii_ioctl(&dev->mii, if_mii(rq), cmd, NULL); } static const struct ethtool_ops dm9601_ethtool_ops = { .get_drvinfo = dm9601_get_drvinfo, .get_link = dm9601_get_link, .get_msglevel = usbnet_get_msglevel, .set_msglevel = usbnet_set_msglevel, .get_eeprom_len = dm9601_get_eeprom_len, .get_eeprom = dm9601_get_eeprom, .nway_reset = usbnet_nway_reset, .get_link_ksettings = usbnet_get_link_ksettings, .set_link_ksettings = usbnet_set_link_ksettings, }; static void dm9601_set_multicast(struct net_device *net) { struct usbnet *dev = netdev_priv(net); /* We use the 20 byte dev->data for our 8 byte filter buffer * to avoid allocating memory that is tricky to free later */ u8 *hashes = (u8 *) & dev->data; u8 rx_ctl = 0x31; memset(hashes, 0x00, DM_MCAST_SIZE); hashes[DM_MCAST_SIZE - 1] |= 0x80; /* broadcast address */ if (net->flags & IFF_PROMISC) { rx_ctl |= 0x02; } else if (net->flags & IFF_ALLMULTI || netdev_mc_count(net) > DM_MAX_MCAST) { rx_ctl |= 0x08; } else if (!netdev_mc_empty(net)) { struct netdev_hw_addr *ha; netdev_for_each_mc_addr(ha, net) { u32 crc = ether_crc(ETH_ALEN, ha->addr) >> 26; hashes[crc >> 3] |= 1 << (crc & 0x7); } } dm_write_async(dev, DM_MCAST_ADDR, DM_MCAST_SIZE, hashes); dm_write_reg_async(dev, DM_RX_CTRL, rx_ctl); } static void __dm9601_set_mac_address(struct usbnet *dev) { dm_write_async(dev, DM_PHY_ADDR, ETH_ALEN, dev->net->dev_addr); } static int dm9601_set_mac_address(struct net_device *net, void *p) { struct sockaddr *addr = p; struct usbnet *dev = netdev_priv(net); if (!is_valid_ether_addr(addr->sa_data)) { dev_err(&net->dev, "not setting invalid mac address %pM\n", addr->sa_data); return -EINVAL; } memcpy(net->dev_addr, addr->sa_data, net->addr_len); __dm9601_set_mac_address(dev); return 0; } static const struct net_device_ops dm9601_netdev_ops = { .ndo_open = usbnet_open, .ndo_stop = usbnet_stop, .ndo_start_xmit = usbnet_start_xmit, .ndo_tx_timeout = usbnet_tx_timeout, .ndo_change_mtu = usbnet_change_mtu, .ndo_get_stats64 = usbnet_get_stats64, .ndo_validate_addr = eth_validate_addr, .ndo_do_ioctl = dm9601_ioctl, .ndo_set_rx_mode = dm9601_set_multicast, .ndo_set_mac_address = dm9601_set_mac_address, }; static int dm9601_bind(struct usbnet *dev, struct usb_interface *intf) { int ret; u8 mac[ETH_ALEN], id; ret = usbnet_get_endpoints(dev, intf); if (ret) goto out; dev->net->netdev_ops = &dm9601_netdev_ops; dev->net->ethtool_ops = &dm9601_ethtool_ops; dev->net->hard_header_len += DM_TX_OVERHEAD; dev->hard_mtu = dev->net->mtu + dev->net->hard_header_len; /* dm9620/21a require room for 4 byte padding, even in dm9601 * mode, so we need +1 to be able to receive full size * ethernet frames. */ dev->rx_urb_size = dev->net->mtu + ETH_HLEN + DM_RX_OVERHEAD + 1; dev->mii.dev = dev->net; dev->mii.mdio_read = dm9601_mdio_read; dev->mii.mdio_write = dm9601_mdio_write; dev->mii.phy_id_mask = 0x1f; dev->mii.reg_num_mask = 0x1f; /* reset */ dm_write_reg(dev, DM_NET_CTRL, 1); udelay(20); /* read MAC */ if (dm_read(dev, DM_PHY_ADDR, ETH_ALEN, mac) < 0) { printk(KERN_ERR "Error reading MAC address\n"); ret = -ENODEV; goto out; } /* * Overwrite the auto-generated address only with good ones. */ if (is_valid_ether_addr(mac)) memcpy(dev->net->dev_addr, mac, ETH_ALEN); else { printk(KERN_WARNING "dm9601: No valid MAC address in EEPROM, using %pM\n", dev->net->dev_addr); __dm9601_set_mac_address(dev); } if (dm_read_reg(dev, DM_CHIP_ID, &id) < 0) { netdev_err(dev->net, "Error reading chip ID\n"); ret = -ENODEV; goto out; } /* put dm9620 devices in dm9601 mode */ if (id == ID_DM9620) { u8 mode; if (dm_read_reg(dev, DM_MODE_CTRL, &mode) < 0) { netdev_err(dev->net, "Error reading MODE_CTRL\n"); ret = -ENODEV; goto out; } dm_write_reg(dev, DM_MODE_CTRL, mode & 0x7f); } /* power up phy */ dm_write_reg(dev, DM_GPR_CTRL, 1); dm_write_reg(dev, DM_GPR_DATA, 0); /* receive broadcast packets */ dm9601_set_multicast(dev->net); dm9601_mdio_write(dev->net, dev->mii.phy_id, MII_BMCR, BMCR_RESET); dm9601_mdio_write(dev->net, dev->mii.phy_id, MII_ADVERTISE, ADVERTISE_ALL | ADVERTISE_CSMA | ADVERTISE_PAUSE_CAP); mii_nway_restart(&dev->mii); out: return ret; } static int dm9601_rx_fixup(struct usbnet *dev, struct sk_buff *skb) { u8 status; int len; /* format: b1: rx status b2: packet length (incl crc) low b3: packet length (incl crc) high b4..n-4: packet data bn-3..bn: ethernet crc */ if (unlikely(skb->len < DM_RX_OVERHEAD)) { dev_err(&dev->udev->dev, "unexpected tiny rx frame\n"); return 0; } status = skb->data[0]; len = (skb->data[1] | (skb->data[2] << 8)) - 4; if (unlikely(status & 0xbf)) { if (status & 0x01) dev->net->stats.rx_fifo_errors++; if (status & 0x02) dev->net->stats.rx_crc_errors++; if (status & 0x04) dev->net->stats.rx_frame_errors++; if (status & 0x20) dev->net->stats.rx_missed_errors++; if (status & 0x90) dev->net->stats.rx_length_errors++; return 0; } skb_pull(skb, 3); skb_trim(skb, len); return 1; } static struct sk_buff *dm9601_tx_fixup(struct usbnet *dev, struct sk_buff *skb, gfp_t flags) { int len, pad; /* format: b1: packet length low b2: packet length high b3..n: packet data */ len = skb->len + DM_TX_OVERHEAD; /* workaround for dm962x errata with tx fifo getting out of * sync if a USB bulk transfer retry happens right after a * packet with odd / maxpacket length by adding up to 3 bytes * padding. */ while ((len & 1) || !(len % dev->maxpacket)) len++; len -= DM_TX_OVERHEAD; /* hw header doesn't count as part of length */ pad = len - skb->len; if (skb_headroom(skb) < DM_TX_OVERHEAD || skb_tailroom(skb) < pad) { struct sk_buff *skb2; skb2 = skb_copy_expand(skb, DM_TX_OVERHEAD, pad, flags); dev_kfree_skb_any(skb); skb = skb2; if (!skb) return NULL; } __skb_push(skb, DM_TX_OVERHEAD); if (pad) { memset(skb->data + skb->len, 0, pad); __skb_put(skb, pad); } skb->data[0] = len; skb->data[1] = len >> 8; return skb; } static void dm9601_status(struct usbnet *dev, struct urb *urb) { int link; u8 *buf; /* format: b0: net status b1: tx status 1 b2: tx status 2 b3: rx status b4: rx overflow b5: rx count b6: tx count b7: gpr */ if (urb->actual_length < 8) return; buf = urb->transfer_buffer; link = !!(buf[0] & 0x40); if (netif_carrier_ok(dev->net) != link) { usbnet_link_change(dev, link, 1); netdev_dbg(dev->net, "Link Status is: %d\n", link); } } static int dm9601_link_reset(struct usbnet *dev) { struct ethtool_cmd ecmd = { .cmd = ETHTOOL_GSET }; mii_check_media(&dev->mii, 1, 1); mii_ethtool_gset(&dev->mii, &ecmd); netdev_dbg(dev->net, "link_reset() speed: %u duplex: %d\n", ethtool_cmd_speed(&ecmd), ecmd.duplex); return 0; } static const struct driver_info dm9601_info = { .description = "Davicom DM96xx USB 10/100 Ethernet", .flags = FLAG_ETHER | FLAG_LINK_INTR, .bind = dm9601_bind, .rx_fixup = dm9601_rx_fixup, .tx_fixup = dm9601_tx_fixup, .status = dm9601_status, .link_reset = dm9601_link_reset, .reset = dm9601_link_reset, }; static const struct usb_device_id products[] = { { USB_DEVICE(0x07aa, 0x9601), /* Corega FEther USB-TXC */ .driver_info = (unsigned long)&dm9601_info, }, { USB_DEVICE(0x0a46, 0x9601), /* Davicom USB-100 */ .driver_info = (unsigned long)&dm9601_info, }, { USB_DEVICE(0x0a46, 0x6688), /* ZT6688 USB NIC */ .driver_info = (unsigned long)&dm9601_info, }, { USB_DEVICE(0x0a46, 0x0268), /* ShanTou ST268 USB NIC */ .driver_info = (unsigned long)&dm9601_info, }, { USB_DEVICE(0x0a46, 0x8515), /* ADMtek ADM8515 USB NIC */ .driver_info = (unsigned long)&dm9601_info, }, { USB_DEVICE(0x0a47, 0x9601), /* Hirose USB-100 */ .driver_info = (unsigned long)&dm9601_info, }, { USB_DEVICE(0x0fe6, 0x8101), /* DM9601 USB to Fast Ethernet Adapter */ .driver_info = (unsigned long)&dm9601_info, }, { USB_DEVICE(0x0fe6, 0x9700), /* DM9601 USB to Fast Ethernet Adapter */ .driver_info = (unsigned long)&dm9601_info, }, { USB_DEVICE(0x0a46, 0x9000), /* DM9000E */ .driver_info = (unsigned long)&dm9601_info, }, { USB_DEVICE(0x0a46, 0x9620), /* DM9620 USB to Fast Ethernet Adapter */ .driver_info = (unsigned long)&dm9601_info, }, { USB_DEVICE(0x0a46, 0x9621), /* DM9621A USB to Fast Ethernet Adapter */ .driver_info = (unsigned long)&dm9601_info, }, { USB_DEVICE(0x0a46, 0x9622), /* DM9622 USB to Fast Ethernet Adapter */ .driver_info = (unsigned long)&dm9601_info, }, { USB_DEVICE(0x0a46, 0x0269), /* DM962OA USB to Fast Ethernet Adapter */ .driver_info = (unsigned long)&dm9601_info, }, { USB_DEVICE(0x0a46, 0x1269), /* DM9621A USB to Fast Ethernet Adapter */ .driver_info = (unsigned long)&dm9601_info, }, {}, // END }; MODULE_DEVICE_TABLE(usb, products); static struct usb_driver dm9601_driver = { .name = "dm9601", .id_table = products, .probe = usbnet_probe, .disconnect = usbnet_disconnect, .suspend = usbnet_suspend, .resume = usbnet_resume, .disable_hub_initiated_lpm = 1, }; module_usb_driver(dm9601_driver); MODULE_AUTHOR("Peter Korsgaard <jacmet@sunsite.dk>"); MODULE_DESCRIPTION("Davicom DM96xx USB 10/100 ethernet devices"); MODULE_LICENSE("GPL");
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.
Created with Cregit http://github.com/cregit/cregit
Version 2.0-RC1