Contributors: 6
Author Tokens Token Proportion Commits Commit Proportion
Michael Buesch 2441 92.11% 6 37.50%
Rafał Miłecki 62 2.34% 4 25.00%
Gábor Stefanik 42 1.58% 1 6.25%
Hauke Mehrtens 40 1.51% 3 18.75%
John W. Linville 38 1.43% 1 6.25%
Aurelien Jarno 27 1.02% 1 6.25%
Total 2650 16 


#ifndef LINUX_SSB_CHIPCO_H_
#define LINUX_SSB_CHIPCO_H_

/* SonicsSiliconBackplane CHIPCOMMON core hardware definitions
 *
 * The chipcommon core provides chip identification, SB control,
 * jtag, 0/1/2 uarts, clock frequency control, a watchdog interrupt timer,
 * gpio interface, extbus, and support for serial and parallel flashes.
 *
 * Copyright 2005, Broadcom Corporation
 * Copyright 2006, Michael Buesch <m@bues.ch>
 *
 * Licensed under the GPL version 2. See COPYING for details.
 */

/** ChipCommon core registers. **/

#define SSB_CHIPCO_CHIPID		0x0000
#define  SSB_CHIPCO_IDMASK		0x0000FFFF
#define  SSB_CHIPCO_REVMASK		0x000F0000
#define  SSB_CHIPCO_REVSHIFT		16
#define  SSB_CHIPCO_PACKMASK		0x00F00000
#define  SSB_CHIPCO_PACKSHIFT		20
#define  SSB_CHIPCO_NRCORESMASK		0x0F000000
#define  SSB_CHIPCO_NRCORESSHIFT	24
#define SSB_CHIPCO_CAP	 		0x0004		/* Capabilities */
#define  SSB_CHIPCO_CAP_NRUART		0x00000003	/* # of UARTs */
#define  SSB_CHIPCO_CAP_MIPSEB		0x00000004	/* MIPS in BigEndian Mode */
#define  SSB_CHIPCO_CAP_UARTCLK		0x00000018	/* UART clock select */
#define   SSB_CHIPCO_CAP_UARTCLK_INT	0x00000008	/* UARTs are driven by internal divided clock */
#define  SSB_CHIPCO_CAP_UARTGPIO	0x00000020	/* UARTs on GPIO 15-12 */
#define  SSB_CHIPCO_CAP_EXTBUS		0x000000C0	/* External buses present */
#define  SSB_CHIPCO_CAP_FLASHT		0x00000700	/* Flash Type */
#define   SSB_CHIPCO_FLASHT_NONE	0x00000000	/* No flash */
#define   SSB_CHIPCO_FLASHT_STSER	0x00000100	/* ST serial flash */
#define   SSB_CHIPCO_FLASHT_ATSER	0x00000200	/* Atmel serial flash */
#define	  SSB_CHIPCO_FLASHT_PARA	0x00000700	/* Parallel flash */
#define  SSB_CHIPCO_CAP_PLLT		0x00038000	/* PLL Type */
#define   SSB_PLLTYPE_NONE		0x00000000
#define   SSB_PLLTYPE_1			0x00010000	/* 48Mhz base, 3 dividers */
#define   SSB_PLLTYPE_2			0x00020000	/* 48Mhz, 4 dividers */
#define   SSB_PLLTYPE_3			0x00030000	/* 25Mhz, 2 dividers */
#define   SSB_PLLTYPE_4			0x00008000	/* 48Mhz, 4 dividers */
#define   SSB_PLLTYPE_5			0x00018000	/* 25Mhz, 4 dividers */
#define   SSB_PLLTYPE_6			0x00028000	/* 100/200 or 120/240 only */
#define   SSB_PLLTYPE_7			0x00038000	/* 25Mhz, 4 dividers */
#define  SSB_CHIPCO_CAP_PCTL		0x00040000	/* Power Control */
#define  SSB_CHIPCO_CAP_OTPS		0x00380000	/* OTP size */
#define  SSB_CHIPCO_CAP_OTPS_SHIFT	19
#define  SSB_CHIPCO_CAP_OTPS_BASE	5
#define  SSB_CHIPCO_CAP_JTAGM		0x00400000	/* JTAG master present */
#define  SSB_CHIPCO_CAP_BROM		0x00800000	/* Internal boot ROM active */
#define  SSB_CHIPCO_CAP_64BIT		0x08000000	/* 64-bit Backplane */
#define  SSB_CHIPCO_CAP_PMU		0x10000000	/* PMU available (rev >= 20) */
#define  SSB_CHIPCO_CAP_ECI		0x20000000	/* ECI available (rev >= 20) */
#define  SSB_CHIPCO_CAP_SPROM		0x40000000	/* SPROM present */
#define SSB_CHIPCO_CORECTL		0x0008
#define  SSB_CHIPCO_CORECTL_UARTCLK0	0x00000001	/* Drive UART with internal clock */
#define	 SSB_CHIPCO_CORECTL_SE		0x00000002	/* sync clk out enable (corerev >= 3) */
#define  SSB_CHIPCO_CORECTL_UARTCLKEN	0x00000008	/* UART clock enable (rev >= 21) */
#define SSB_CHIPCO_BIST			0x000C
#define SSB_CHIPCO_OTPS			0x0010		/* OTP status */
#define	 SSB_CHIPCO_OTPS_PROGFAIL	0x80000000
#define	 SSB_CHIPCO_OTPS_PROTECT	0x00000007
#define	 SSB_CHIPCO_OTPS_HW_PROTECT	0x00000001
#define	 SSB_CHIPCO_OTPS_SW_PROTECT	0x00000002
#define	 SSB_CHIPCO_OTPS_CID_PROTECT	0x00000004
#define SSB_CHIPCO_OTPC			0x0014		/* OTP control */
#define	 SSB_CHIPCO_OTPC_RECWAIT	0xFF000000
#define	 SSB_CHIPCO_OTPC_PROGWAIT	0x00FFFF00
#define	 SSB_CHIPCO_OTPC_PRW_SHIFT	8
#define	 SSB_CHIPCO_OTPC_MAXFAIL	0x00000038
#define	 SSB_CHIPCO_OTPC_VSEL		0x00000006
#define	 SSB_CHIPCO_OTPC_SELVL		0x00000001
#define SSB_CHIPCO_OTPP			0x0018		/* OTP prog */
#define	 SSB_CHIPCO_OTPP_COL		0x000000FF
#define	 SSB_CHIPCO_OTPP_ROW		0x0000FF00
#define	 SSB_CHIPCO_OTPP_ROW_SHIFT	8
#define	 SSB_CHIPCO_OTPP_READERR	0x10000000
#define	 SSB_CHIPCO_OTPP_VALUE		0x20000000
#define	 SSB_CHIPCO_OTPP_READ		0x40000000
#define	 SSB_CHIPCO_OTPP_START		0x80000000
#define	 SSB_CHIPCO_OTPP_BUSY		0x80000000
#define SSB_CHIPCO_IRQSTAT		0x0020
#define SSB_CHIPCO_IRQMASK		0x0024
#define	 SSB_CHIPCO_IRQ_GPIO		0x00000001	/* gpio intr */
#define	 SSB_CHIPCO_IRQ_EXT		0x00000002	/* ro: ext intr pin (corerev >= 3) */
#define	 SSB_CHIPCO_IRQ_WDRESET		0x80000000	/* watchdog reset occurred */
#define SSB_CHIPCO_CHIPCTL		0x0028		/* Rev >= 11 only */
#define SSB_CHIPCO_CHIPSTAT		0x002C		/* Rev >= 11 only */
#define SSB_CHIPCO_JCMD			0x0030		/* Rev >= 10 only */
#define  SSB_CHIPCO_JCMD_START		0x80000000
#define  SSB_CHIPCO_JCMD_BUSY		0x80000000
#define  SSB_CHIPCO_JCMD_PAUSE		0x40000000
#define  SSB_CHIPCO_JCMD0_ACC_MASK	0x0000F000
#define  SSB_CHIPCO_JCMD0_ACC_IRDR	0x00000000
#define  SSB_CHIPCO_JCMD0_ACC_DR	0x00001000
#define  SSB_CHIPCO_JCMD0_ACC_IR	0x00002000
#define  SSB_CHIPCO_JCMD0_ACC_RESET	0x00003000
#define  SSB_CHIPCO_JCMD0_ACC_IRPDR	0x00004000
#define  SSB_CHIPCO_JCMD0_ACC_PDR	0x00005000
#define  SSB_CHIPCO_JCMD0_IRW_MASK	0x00000F00
#define  SSB_CHIPCO_JCMD_ACC_MASK	0x000F0000	/* Changes for corerev 11 */
#define  SSB_CHIPCO_JCMD_ACC_IRDR	0x00000000
#define  SSB_CHIPCO_JCMD_ACC_DR		0x00010000
#define  SSB_CHIPCO_JCMD_ACC_IR		0x00020000
#define  SSB_CHIPCO_JCMD_ACC_RESET	0x00030000
#define  SSB_CHIPCO_JCMD_ACC_IRPDR	0x00040000
#define  SSB_CHIPCO_JCMD_ACC_PDR	0x00050000
#define  SSB_CHIPCO_JCMD_IRW_MASK	0x00001F00
#define  SSB_CHIPCO_JCMD_IRW_SHIFT	8
#define  SSB_CHIPCO_JCMD_DRW_MASK	0x0000003F
#define SSB_CHIPCO_JIR			0x0034		/* Rev >= 10 only */
#define SSB_CHIPCO_JDR			0x0038		/* Rev >= 10 only */
#define SSB_CHIPCO_JCTL			0x003C		/* Rev >= 10 only */
#define  SSB_CHIPCO_JCTL_FORCE_CLK	4		/* Force clock */
#define  SSB_CHIPCO_JCTL_EXT_EN		2		/* Enable external targets */
#define  SSB_CHIPCO_JCTL_EN		1		/* Enable Jtag master */
#define SSB_CHIPCO_FLASHCTL		0x0040
#define  SSB_CHIPCO_FLASHCTL_START	0x80000000
#define  SSB_CHIPCO_FLASHCTL_BUSY	SSB_CHIPCO_FLASHCTL_START
#define SSB_CHIPCO_FLASHADDR		0x0044
#define SSB_CHIPCO_FLASHDATA		0x0048
#define SSB_CHIPCO_BCAST_ADDR		0x0050
#define SSB_CHIPCO_BCAST_DATA		0x0054
#define SSB_CHIPCO_GPIOPULLUP		0x0058		/* Rev >= 20 only */
#define SSB_CHIPCO_GPIOPULLDOWN		0x005C		/* Rev >= 20 only */
#define SSB_CHIPCO_GPIOIN		0x0060
#define SSB_CHIPCO_GPIOOUT		0x0064
#define SSB_CHIPCO_GPIOOUTEN		0x0068
#define SSB_CHIPCO_GPIOCTL		0x006C
#define SSB_CHIPCO_GPIOPOL		0x0070
#define SSB_CHIPCO_GPIOIRQ		0x0074
#define SSB_CHIPCO_WATCHDOG		0x0080
#define SSB_CHIPCO_GPIOTIMER		0x0088		/* LED powersave (corerev >= 16) */
#define  SSB_CHIPCO_GPIOTIMER_OFFTIME	0x0000FFFF
#define  SSB_CHIPCO_GPIOTIMER_OFFTIME_SHIFT	0
#define  SSB_CHIPCO_GPIOTIMER_ONTIME	0xFFFF0000
#define  SSB_CHIPCO_GPIOTIMER_ONTIME_SHIFT	16
#define SSB_CHIPCO_GPIOTOUTM		0x008C		/* LED powersave (corerev >= 16) */
#define SSB_CHIPCO_CLOCK_N		0x0090
#define SSB_CHIPCO_CLOCK_SB		0x0094
#define SSB_CHIPCO_CLOCK_PCI		0x0098
#define SSB_CHIPCO_CLOCK_M2		0x009C
#define SSB_CHIPCO_CLOCK_MIPS		0x00A0
#define SSB_CHIPCO_CLKDIV		0x00A4		/* Rev >= 3 only */
#define	 SSB_CHIPCO_CLKDIV_SFLASH	0x0F000000
#define	 SSB_CHIPCO_CLKDIV_SFLASH_SHIFT	24
#define	 SSB_CHIPCO_CLKDIV_OTP		0x000F0000
#define	 SSB_CHIPCO_CLKDIV_OTP_SHIFT	16
#define	 SSB_CHIPCO_CLKDIV_JTAG		0x00000F00
#define	 SSB_CHIPCO_CLKDIV_JTAG_SHIFT	8
#define	 SSB_CHIPCO_CLKDIV_UART		0x000000FF
#define SSB_CHIPCO_PLLONDELAY		0x00B0		/* Rev >= 4 only */
#define SSB_CHIPCO_FREFSELDELAY		0x00B4		/* Rev >= 4 only */
#define SSB_CHIPCO_SLOWCLKCTL		0x00B8		/* 6 <= Rev <= 9 only */
#define  SSB_CHIPCO_SLOWCLKCTL_SRC	0x00000007	/* slow clock source mask */
#define	  SSB_CHIPCO_SLOWCLKCTL_SRC_LPO		0x00000000	/* source of slow clock is LPO */
#define   SSB_CHIPCO_SLOWCLKCTL_SRC_XTAL	0x00000001	/* source of slow clock is crystal */
#define	  SSB_CHIPCO_SLOECLKCTL_SRC_PCI		0x00000002	/* source of slow clock is PCI */
#define  SSB_CHIPCO_SLOWCLKCTL_LPOFREQ	0x00000200	/* LPOFreqSel, 1: 160Khz, 0: 32KHz */
#define  SSB_CHIPCO_SLOWCLKCTL_LPOPD	0x00000400	/* LPOPowerDown, 1: LPO is disabled, 0: LPO is enabled */
#define  SSB_CHIPCO_SLOWCLKCTL_FSLOW	0x00000800	/* ForceSlowClk, 1: sb/cores running on slow clock, 0: power logic control */
#define  SSB_CHIPCO_SLOWCLKCTL_IPLL	0x00001000	/* IgnorePllOffReq, 1/0: power logic ignores/honors PLL clock disable requests from core */
#define  SSB_CHIPCO_SLOWCLKCTL_ENXTAL	0x00002000	/* XtalControlEn, 1/0: power logic does/doesn't disable crystal when appropriate */
#define  SSB_CHIPCO_SLOWCLKCTL_XTALPU	0x00004000	/* XtalPU (RO), 1/0: crystal running/disabled */
#define  SSB_CHIPCO_SLOWCLKCTL_CLKDIV	0xFFFF0000	/* ClockDivider (SlowClk = 1/(4+divisor)) */
#define  SSB_CHIPCO_SLOWCLKCTL_CLKDIV_SHIFT	16
#define SSB_CHIPCO_SYSCLKCTL		0x00C0		/* Rev >= 3 only */
#define	 SSB_CHIPCO_SYSCLKCTL_IDLPEN	0x00000001	/* ILPen: Enable Idle Low Power */
#define	 SSB_CHIPCO_SYSCLKCTL_ALPEN	0x00000002	/* ALPen: Enable Active Low Power */
#define	 SSB_CHIPCO_SYSCLKCTL_PLLEN	0x00000004	/* ForcePLLOn */
#define	 SSB_CHIPCO_SYSCLKCTL_FORCEALP	0x00000008	/* Force ALP (or HT if ALPen is not set */
#define	 SSB_CHIPCO_SYSCLKCTL_FORCEHT	0x00000010	/* Force HT */
#define  SSB_CHIPCO_SYSCLKCTL_CLKDIV	0xFFFF0000	/* ClkDiv  (ILP = 1/(4+divisor)) */
#define  SSB_CHIPCO_SYSCLKCTL_CLKDIV_SHIFT	16
#define SSB_CHIPCO_CLKSTSTR		0x00C4		/* Rev >= 3 only */
#define SSB_CHIPCO_PCMCIA_CFG		0x0100
#define SSB_CHIPCO_PCMCIA_MEMWAIT	0x0104
#define SSB_CHIPCO_PCMCIA_ATTRWAIT	0x0108
#define SSB_CHIPCO_PCMCIA_IOWAIT	0x010C
#define SSB_CHIPCO_IDE_CFG		0x0110
#define SSB_CHIPCO_IDE_MEMWAIT		0x0114
#define SSB_CHIPCO_IDE_ATTRWAIT		0x0118
#define SSB_CHIPCO_IDE_IOWAIT		0x011C
#define SSB_CHIPCO_PROG_CFG		0x0120
#define SSB_CHIPCO_PROG_WAITCNT		0x0124
#define SSB_CHIPCO_FLASH_CFG		0x0128
#define SSB_CHIPCO_FLASH_WAITCNT	0x012C
#define SSB_CHIPCO_CLKCTLST		0x01E0 /* Clock control and status (rev >= 20) */
#define  SSB_CHIPCO_CLKCTLST_FORCEALP	0x00000001 /* Force ALP request */
#define  SSB_CHIPCO_CLKCTLST_FORCEHT	0x00000002 /* Force HT request */
#define  SSB_CHIPCO_CLKCTLST_FORCEILP	0x00000004 /* Force ILP request */
#define  SSB_CHIPCO_CLKCTLST_HAVEALPREQ	0x00000008 /* ALP available request */
#define  SSB_CHIPCO_CLKCTLST_HAVEHTREQ	0x00000010 /* HT available request */
#define  SSB_CHIPCO_CLKCTLST_HWCROFF	0x00000020 /* Force HW clock request off */
#define  SSB_CHIPCO_CLKCTLST_HAVEALP	0x00010000 /* ALP available */
#define  SSB_CHIPCO_CLKCTLST_HAVEHT	0x00020000 /* HT available */
#define  SSB_CHIPCO_CLKCTLST_4328A0_HAVEHT	0x00010000 /* 4328a0 has reversed bits */
#define  SSB_CHIPCO_CLKCTLST_4328A0_HAVEALP	0x00020000 /* 4328a0 has reversed bits */
#define SSB_CHIPCO_HW_WORKAROUND	0x01E4 /* Hardware workaround (rev >= 20) */
#define SSB_CHIPCO_UART0_DATA		0x0300
#define SSB_CHIPCO_UART0_IMR		0x0304
#define SSB_CHIPCO_UART0_FCR		0x0308
#define SSB_CHIPCO_UART0_LCR		0x030C
#define SSB_CHIPCO_UART0_MCR		0x0310
#define SSB_CHIPCO_UART0_LSR		0x0314
#define SSB_CHIPCO_UART0_MSR		0x0318
#define SSB_CHIPCO_UART0_SCRATCH	0x031C
#define SSB_CHIPCO_UART1_DATA		0x0400
#define SSB_CHIPCO_UART1_IMR		0x0404
#define SSB_CHIPCO_UART1_FCR		0x0408
#define SSB_CHIPCO_UART1_LCR		0x040C
#define SSB_CHIPCO_UART1_MCR		0x0410
#define SSB_CHIPCO_UART1_LSR		0x0414
#define SSB_CHIPCO_UART1_MSR		0x0418
#define SSB_CHIPCO_UART1_SCRATCH	0x041C
/* PMU registers (rev >= 20) */
#define SSB_CHIPCO_PMU_CTL			0x0600 /* PMU control */
#define  SSB_CHIPCO_PMU_CTL_ILP_DIV		0xFFFF0000 /* ILP div mask */
#define  SSB_CHIPCO_PMU_CTL_ILP_DIV_SHIFT	16
#define  SSB_CHIPCO_PMU_CTL_PLL_UPD		0x00000400
#define  SSB_CHIPCO_PMU_CTL_NOILPONW		0x00000200 /* No ILP on wait */
#define  SSB_CHIPCO_PMU_CTL_HTREQEN		0x00000100 /* HT req enable */
#define  SSB_CHIPCO_PMU_CTL_ALPREQEN		0x00000080 /* ALP req enable */
#define  SSB_CHIPCO_PMU_CTL_XTALFREQ		0x0000007C /* Crystal freq */
#define  SSB_CHIPCO_PMU_CTL_XTALFREQ_SHIFT	2
#define  SSB_CHIPCO_PMU_CTL_ILPDIVEN		0x00000002 /* ILP div enable */
#define  SSB_CHIPCO_PMU_CTL_LPOSEL		0x00000001 /* LPO sel */
#define SSB_CHIPCO_PMU_CAP			0x0604 /* PMU capabilities */
#define  SSB_CHIPCO_PMU_CAP_REVISION		0x000000FF /* Revision mask */
#define SSB_CHIPCO_PMU_STAT			0x0608 /* PMU status */
#define  SSB_CHIPCO_PMU_STAT_INTPEND		0x00000040 /* Interrupt pending */
#define  SSB_CHIPCO_PMU_STAT_SBCLKST		0x00000030 /* Backplane clock status? */
#define  SSB_CHIPCO_PMU_STAT_HAVEALP		0x00000008 /* ALP available */
#define  SSB_CHIPCO_PMU_STAT_HAVEHT		0x00000004 /* HT available */
#define  SSB_CHIPCO_PMU_STAT_RESINIT		0x00000003 /* Res init */
#define SSB_CHIPCO_PMU_RES_STAT			0x060C /* PMU res status */
#define SSB_CHIPCO_PMU_RES_PEND			0x0610 /* PMU res pending */
#define SSB_CHIPCO_PMU_TIMER			0x0614 /* PMU timer */
#define SSB_CHIPCO_PMU_MINRES_MSK		0x0618 /* PMU min res mask */
#define SSB_CHIPCO_PMU_MAXRES_MSK		0x061C /* PMU max res mask */
#define SSB_CHIPCO_PMU_RES_TABSEL		0x0620 /* PMU res table sel */
#define SSB_CHIPCO_PMU_RES_DEPMSK		0x0624 /* PMU res dep mask */
#define SSB_CHIPCO_PMU_RES_UPDNTM		0x0628 /* PMU res updown timer */
#define SSB_CHIPCO_PMU_RES_TIMER		0x062C /* PMU res timer */
#define SSB_CHIPCO_PMU_CLKSTRETCH		0x0630 /* PMU clockstretch */
#define SSB_CHIPCO_PMU_WATCHDOG			0x0634 /* PMU watchdog */
#define SSB_CHIPCO_PMU_RES_REQTS		0x0640 /* PMU res req timer sel */
#define SSB_CHIPCO_PMU_RES_REQT			0x0644 /* PMU res req timer */
#define SSB_CHIPCO_PMU_RES_REQM			0x0648 /* PMU res req mask */
#define SSB_CHIPCO_CHIPCTL_ADDR			0x0650
#define SSB_CHIPCO_CHIPCTL_DATA			0x0654
#define SSB_CHIPCO_REGCTL_ADDR			0x0658
#define SSB_CHIPCO_REGCTL_DATA			0x065C
#define SSB_CHIPCO_PLLCTL_ADDR			0x0660
#define SSB_CHIPCO_PLLCTL_DATA			0x0664



/** PMU PLL registers */

/* PMU rev 0 PLL registers */
#define SSB_PMU0_PLLCTL0			0
#define  SSB_PMU0_PLLCTL0_PDIV_MSK		0x00000001
#define  SSB_PMU0_PLLCTL0_PDIV_FREQ		25000 /* kHz */
#define SSB_PMU0_PLLCTL1			1
#define  SSB_PMU0_PLLCTL1_WILD_IMSK		0xF0000000 /* Wild int mask (low nibble) */
#define  SSB_PMU0_PLLCTL1_WILD_IMSK_SHIFT	28
#define  SSB_PMU0_PLLCTL1_WILD_FMSK		0x0FFFFF00 /* Wild frac mask */
#define  SSB_PMU0_PLLCTL1_WILD_FMSK_SHIFT	8
#define  SSB_PMU0_PLLCTL1_STOPMOD		0x00000040 /* Stop mod */
#define SSB_PMU0_PLLCTL2			2
#define  SSB_PMU0_PLLCTL2_WILD_IMSKHI		0x0000000F /* Wild int mask (high nibble) */
#define  SSB_PMU0_PLLCTL2_WILD_IMSKHI_SHIFT	0

/* PMU rev 1 PLL registers */
#define SSB_PMU1_PLLCTL0			0
#define  SSB_PMU1_PLLCTL0_P1DIV			0x00F00000 /* P1 div */
#define  SSB_PMU1_PLLCTL0_P1DIV_SHIFT		20
#define  SSB_PMU1_PLLCTL0_P2DIV			0x0F000000 /* P2 div */
#define  SSB_PMU1_PLLCTL0_P2DIV_SHIFT		24
#define SSB_PMU1_PLLCTL1			1
#define  SSB_PMU1_PLLCTL1_M1DIV			0x000000FF /* M1 div */
#define  SSB_PMU1_PLLCTL1_M1DIV_SHIFT		0
#define  SSB_PMU1_PLLCTL1_M2DIV			0x0000FF00 /* M2 div */
#define  SSB_PMU1_PLLCTL1_M2DIV_SHIFT		8
#define  SSB_PMU1_PLLCTL1_M3DIV			0x00FF0000 /* M3 div */
#define  SSB_PMU1_PLLCTL1_M3DIV_SHIFT		16
#define  SSB_PMU1_PLLCTL1_M4DIV			0xFF000000 /* M4 div */
#define  SSB_PMU1_PLLCTL1_M4DIV_SHIFT		24
#define SSB_PMU1_PLLCTL2			2
#define  SSB_PMU1_PLLCTL2_M5DIV			0x000000FF /* M5 div */
#define  SSB_PMU1_PLLCTL2_M5DIV_SHIFT		0
#define  SSB_PMU1_PLLCTL2_M6DIV			0x0000FF00 /* M6 div */
#define  SSB_PMU1_PLLCTL2_M6DIV_SHIFT		8
#define  SSB_PMU1_PLLCTL2_NDIVMODE		0x000E0000 /* NDIV mode */
#define  SSB_PMU1_PLLCTL2_NDIVMODE_SHIFT	17
#define  SSB_PMU1_PLLCTL2_NDIVINT		0x1FF00000 /* NDIV int */
#define  SSB_PMU1_PLLCTL2_NDIVINT_SHIFT		20
#define SSB_PMU1_PLLCTL3			3
#define  SSB_PMU1_PLLCTL3_NDIVFRAC		0x00FFFFFF /* NDIV frac */
#define  SSB_PMU1_PLLCTL3_NDIVFRAC_SHIFT	0
#define SSB_PMU1_PLLCTL4			4
#define SSB_PMU1_PLLCTL5			5
#define  SSB_PMU1_PLLCTL5_CLKDRV		0xFFFFFF00 /* clk drv */
#define  SSB_PMU1_PLLCTL5_CLKDRV_SHIFT		8

/* BCM4312 PLL resource numbers. */
#define SSB_PMURES_4312_SWITCHER_BURST		0
#define SSB_PMURES_4312_SWITCHER_PWM    	1
#define SSB_PMURES_4312_PA_REF_LDO		2
#define SSB_PMURES_4312_CORE_LDO_BURST		3
#define SSB_PMURES_4312_CORE_LDO_PWM		4
#define SSB_PMURES_4312_RADIO_LDO		5
#define SSB_PMURES_4312_ILP_REQUEST		6
#define SSB_PMURES_4312_BG_FILTBYP		7
#define SSB_PMURES_4312_TX_FILTBYP		8
#define SSB_PMURES_4312_RX_FILTBYP		9
#define SSB_PMURES_4312_XTAL_PU			10
#define SSB_PMURES_4312_ALP_AVAIL		11
#define SSB_PMURES_4312_BB_PLL_FILTBYP		12
#define SSB_PMURES_4312_RF_PLL_FILTBYP		13
#define SSB_PMURES_4312_HT_AVAIL		14

/* BCM4325 PLL resource numbers. */
#define SSB_PMURES_4325_BUCK_BOOST_BURST	0
#define SSB_PMURES_4325_CBUCK_BURST		1
#define SSB_PMURES_4325_CBUCK_PWM		2
#define SSB_PMURES_4325_CLDO_CBUCK_BURST	3
#define SSB_PMURES_4325_CLDO_CBUCK_PWM		4
#define SSB_PMURES_4325_BUCK_BOOST_PWM		5
#define SSB_PMURES_4325_ILP_REQUEST		6
#define SSB_PMURES_4325_ABUCK_BURST		7
#define SSB_PMURES_4325_ABUCK_PWM		8
#define SSB_PMURES_4325_LNLDO1_PU		9
#define SSB_PMURES_4325_LNLDO2_PU		10
#define SSB_PMURES_4325_LNLDO3_PU		11
#define SSB_PMURES_4325_LNLDO4_PU		12
#define SSB_PMURES_4325_XTAL_PU			13
#define SSB_PMURES_4325_ALP_AVAIL		14
#define SSB_PMURES_4325_RX_PWRSW_PU		15
#define SSB_PMURES_4325_TX_PWRSW_PU		16
#define SSB_PMURES_4325_RFPLL_PWRSW_PU		17
#define SSB_PMURES_4325_LOGEN_PWRSW_PU		18
#define SSB_PMURES_4325_AFE_PWRSW_PU		19
#define SSB_PMURES_4325_BBPLL_PWRSW_PU		20
#define SSB_PMURES_4325_HT_AVAIL		21

/* BCM4328 PLL resource numbers. */
#define SSB_PMURES_4328_EXT_SWITCHER_PWM	0
#define SSB_PMURES_4328_BB_SWITCHER_PWM		1
#define SSB_PMURES_4328_BB_SWITCHER_BURST	2
#define SSB_PMURES_4328_BB_EXT_SWITCHER_BURST	3
#define SSB_PMURES_4328_ILP_REQUEST		4
#define SSB_PMURES_4328_RADIO_SWITCHER_PWM	5
#define SSB_PMURES_4328_RADIO_SWITCHER_BURST	6
#define SSB_PMURES_4328_ROM_SWITCH		7
#define SSB_PMURES_4328_PA_REF_LDO		8
#define SSB_PMURES_4328_RADIO_LDO		9
#define SSB_PMURES_4328_AFE_LDO			10
#define SSB_PMURES_4328_PLL_LDO			11
#define SSB_PMURES_4328_BG_FILTBYP		12
#define SSB_PMURES_4328_TX_FILTBYP		13
#define SSB_PMURES_4328_RX_FILTBYP		14
#define SSB_PMURES_4328_XTAL_PU			15
#define SSB_PMURES_4328_XTAL_EN			16
#define SSB_PMURES_4328_BB_PLL_FILTBYP		17
#define SSB_PMURES_4328_RF_PLL_FILTBYP		18
#define SSB_PMURES_4328_BB_PLL_PU		19

/* BCM5354 PLL resource numbers. */
#define SSB_PMURES_5354_EXT_SWITCHER_PWM	0
#define SSB_PMURES_5354_BB_SWITCHER_PWM		1
#define SSB_PMURES_5354_BB_SWITCHER_BURST	2
#define SSB_PMURES_5354_BB_EXT_SWITCHER_BURST	3
#define SSB_PMURES_5354_ILP_REQUEST		4
#define SSB_PMURES_5354_RADIO_SWITCHER_PWM	5
#define SSB_PMURES_5354_RADIO_SWITCHER_BURST	6
#define SSB_PMURES_5354_ROM_SWITCH		7
#define SSB_PMURES_5354_PA_REF_LDO		8
#define SSB_PMURES_5354_RADIO_LDO		9
#define SSB_PMURES_5354_AFE_LDO			10
#define SSB_PMURES_5354_PLL_LDO			11
#define SSB_PMURES_5354_BG_FILTBYP		12
#define SSB_PMURES_5354_TX_FILTBYP		13
#define SSB_PMURES_5354_RX_FILTBYP		14
#define SSB_PMURES_5354_XTAL_PU			15
#define SSB_PMURES_5354_XTAL_EN			16
#define SSB_PMURES_5354_BB_PLL_FILTBYP		17
#define SSB_PMURES_5354_RF_PLL_FILTBYP		18
#define SSB_PMURES_5354_BB_PLL_PU		19



/** Chip specific Chip-Status register contents. */
#define SSB_CHIPCO_CHST_4322_SPROM_EXISTS	0x00000040 /* SPROM present */
#define SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL	0x00000003
#define SSB_CHIPCO_CHST_4325_DEFCIS_SEL		0 /* OTP is powered up, use def. CIS, no SPROM */
#define SSB_CHIPCO_CHST_4325_SPROM_SEL		1 /* OTP is powered up, SPROM is present */
#define SSB_CHIPCO_CHST_4325_OTP_SEL		2 /* OTP is powered up, no SPROM */
#define SSB_CHIPCO_CHST_4325_OTP_PWRDN		3 /* OTP is powered down, SPROM is present */
#define SSB_CHIPCO_CHST_4325_SDIO_USB_MODE	0x00000004
#define SSB_CHIPCO_CHST_4325_SDIO_USB_MODE_SHIFT  2
#define SSB_CHIPCO_CHST_4325_RCAL_VALID		0x00000008
#define SSB_CHIPCO_CHST_4325_RCAL_VALID_SHIFT	3
#define SSB_CHIPCO_CHST_4325_RCAL_VALUE		0x000001F0
#define SSB_CHIPCO_CHST_4325_RCAL_VALUE_SHIFT	4
#define SSB_CHIPCO_CHST_4325_PMUTOP_2B 		0x00000200 /* 1 for 2b, 0 for to 2a */

/** Macros to determine SPROM presence based on Chip-Status register. */
#define SSB_CHIPCO_CHST_4312_SPROM_PRESENT(status) \
	((status & SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL) != \
		SSB_CHIPCO_CHST_4325_OTP_SEL)
#define SSB_CHIPCO_CHST_4322_SPROM_PRESENT(status) \
	(status & SSB_CHIPCO_CHST_4322_SPROM_EXISTS)
#define SSB_CHIPCO_CHST_4325_SPROM_PRESENT(status) \
	(((status & SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL) != \
		SSB_CHIPCO_CHST_4325_DEFCIS_SEL) && \
	 ((status & SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL) != \
		SSB_CHIPCO_CHST_4325_OTP_SEL))



/** Clockcontrol masks and values **/

/* SSB_CHIPCO_CLOCK_N */
#define	SSB_CHIPCO_CLK_N1		0x0000003F	/* n1 control */
#define	SSB_CHIPCO_CLK_N2		0x00003F00	/* n2 control */
#define	SSB_CHIPCO_CLK_N2_SHIFT		8
#define	SSB_CHIPCO_CLK_PLLC		0x000F0000	/* pll control */
#define	SSB_CHIPCO_CLK_PLLC_SHIFT	16

/* SSB_CHIPCO_CLOCK_SB/PCI/UART */
#define	SSB_CHIPCO_CLK_M1		0x0000003F	/* m1 control */
#define	SSB_CHIPCO_CLK_M2		0x00003F00	/* m2 control */
#define	SSB_CHIPCO_CLK_M2_SHIFT		8
#define	SSB_CHIPCO_CLK_M3		0x003F0000	/* m3 control */
#define	SSB_CHIPCO_CLK_M3_SHIFT		16
#define	SSB_CHIPCO_CLK_MC		0x1F000000	/* mux control */
#define	SSB_CHIPCO_CLK_MC_SHIFT		24

/* N3M Clock control magic field values */
#define	SSB_CHIPCO_CLK_F6_2		0x02		/* A factor of 2 in */
#define	SSB_CHIPCO_CLK_F6_3		0x03		/* 6-bit fields like */
#define	SSB_CHIPCO_CLK_F6_4		0x05		/* N1, M1 or M3 */
#define	SSB_CHIPCO_CLK_F6_5		0x09
#define	SSB_CHIPCO_CLK_F6_6		0x11
#define	SSB_CHIPCO_CLK_F6_7		0x21

#define	SSB_CHIPCO_CLK_F5_BIAS		5		/* 5-bit fields get this added */

#define	SSB_CHIPCO_CLK_MC_BYPASS	0x08
#define	SSB_CHIPCO_CLK_MC_M1		0x04
#define	SSB_CHIPCO_CLK_MC_M1M2		0x02
#define	SSB_CHIPCO_CLK_MC_M1M2M3	0x01
#define	SSB_CHIPCO_CLK_MC_M1M3		0x11

/* Type 2 Clock control magic field values */
#define	SSB_CHIPCO_CLK_T2_BIAS		2		/* n1, n2, m1 & m3 bias */
#define	SSB_CHIPCO_CLK_T2M2_BIAS	3		/* m2 bias */

#define	SSB_CHIPCO_CLK_T2MC_M1BYP	1
#define	SSB_CHIPCO_CLK_T2MC_M2BYP	2
#define	SSB_CHIPCO_CLK_T2MC_M3BYP	4

/* Type 6 Clock control magic field values */
#define	SSB_CHIPCO_CLK_T6_MMASK		1		/* bits of interest in m */
#define	SSB_CHIPCO_CLK_T6_M0		120000000	/* sb clock for m = 0 */
#define	SSB_CHIPCO_CLK_T6_M1		100000000	/* sb clock for m = 1 */
#define	SSB_CHIPCO_CLK_SB2MIPS_T6(sb)	(2 * (sb))

/* Common clock base */
#define	SSB_CHIPCO_CLK_BASE1		24000000	/* Half the clock freq */
#define SSB_CHIPCO_CLK_BASE2		12500000	/* Alternate crystal on some PLL's */

/* Clock control values for 200Mhz in 5350 */
#define	SSB_CHIPCO_CLK_5350_N		0x0311
#define	SSB_CHIPCO_CLK_5350_M		0x04020009


/** Bits in the config registers **/

#define	SSB_CHIPCO_CFG_EN		0x0001		/* Enable */
#define	SSB_CHIPCO_CFG_EXTM		0x000E		/* Extif Mode */
#define	 SSB_CHIPCO_CFG_EXTM_ASYNC	0x0002		/* Async/Parallel flash */
#define	 SSB_CHIPCO_CFG_EXTM_SYNC	0x0004		/* Synchronous */
#define	 SSB_CHIPCO_CFG_EXTM_PCMCIA	0x0008		/* PCMCIA */
#define	 SSB_CHIPCO_CFG_EXTM_IDE	0x000A		/* IDE */
#define	SSB_CHIPCO_CFG_DS16		0x0010		/* Data size, 0=8bit, 1=16bit */
#define	SSB_CHIPCO_CFG_CLKDIV		0x0060		/* Sync: Clock divisor */
#define	SSB_CHIPCO_CFG_CLKEN		0x0080		/* Sync: Clock enable */
#define	SSB_CHIPCO_CFG_BSTRO		0x0100		/* Sync: Size/Bytestrobe */


/** Flash-specific control/status values */

/* flashcontrol opcodes for ST flashes */
#define SSB_CHIPCO_FLASHCTL_ST_WREN	0x0006		/* Write Enable */
#define SSB_CHIPCO_FLASHCTL_ST_WRDIS	0x0004		/* Write Disable */
#define SSB_CHIPCO_FLASHCTL_ST_RDSR	0x0105		/* Read Status Register */
#define SSB_CHIPCO_FLASHCTL_ST_WRSR	0x0101		/* Write Status Register */
#define SSB_CHIPCO_FLASHCTL_ST_READ	0x0303		/* Read Data Bytes */
#define SSB_CHIPCO_FLASHCTL_ST_PP	0x0302		/* Page Program */
#define SSB_CHIPCO_FLASHCTL_ST_SE	0x02D8		/* Sector Erase */
#define SSB_CHIPCO_FLASHCTL_ST_BE	0x00C7		/* Bulk Erase */
#define SSB_CHIPCO_FLASHCTL_ST_DP	0x00B9		/* Deep Power-down */
#define SSB_CHIPCO_FLASHCTL_ST_RES	0x03AB		/* Read Electronic Signature */
#define SSB_CHIPCO_FLASHCTL_ST_CSA	0x1000		/* Keep chip select asserted */
#define SSB_CHIPCO_FLASHCTL_ST_SSE	0x0220		/* Sub-sector Erase */

/* Status register bits for ST flashes */
#define SSB_CHIPCO_FLASHSTA_ST_WIP	0x01		/* Write In Progress */
#define SSB_CHIPCO_FLASHSTA_ST_WEL	0x02		/* Write Enable Latch */
#define SSB_CHIPCO_FLASHSTA_ST_BP	0x1C		/* Block Protect */
#define SSB_CHIPCO_FLASHSTA_ST_BP_SHIFT	2
#define SSB_CHIPCO_FLASHSTA_ST_SRWD	0x80		/* Status Register Write Disable */

/* flashcontrol opcodes for Atmel flashes */
#define SSB_CHIPCO_FLASHCTL_AT_READ		0x07E8
#define SSB_CHIPCO_FLASHCTL_AT_PAGE_READ	0x07D2
#define SSB_CHIPCO_FLASHCTL_AT_BUF1_READ	/* FIXME */
#define SSB_CHIPCO_FLASHCTL_AT_BUF2_READ	/* FIXME */
#define SSB_CHIPCO_FLASHCTL_AT_STATUS		0x01D7
#define SSB_CHIPCO_FLASHCTL_AT_BUF1_WRITE	0x0384
#define SSB_CHIPCO_FLASHCTL_AT_BUF2_WRITE	0x0387
#define SSB_CHIPCO_FLASHCTL_AT_BUF1_ERASE_PRGM	0x0283	/* Erase program */
#define SSB_CHIPCO_FLASHCTL_AT_BUF2_ERASE_PRGM	0x0286	/* Erase program */
#define SSB_CHIPCO_FLASHCTL_AT_BUF1_PROGRAM	0x0288
#define SSB_CHIPCO_FLASHCTL_AT_BUF2_PROGRAM	0x0289
#define SSB_CHIPCO_FLASHCTL_AT_PAGE_ERASE	0x0281
#define SSB_CHIPCO_FLASHCTL_AT_BLOCK_ERASE	0x0250
#define SSB_CHIPCO_FLASHCTL_AT_BUF1_WRER_PRGM	0x0382	/* Write erase program */
#define SSB_CHIPCO_FLASHCTL_AT_BUF2_WRER_PRGM	0x0385	/* Write erase program */
#define SSB_CHIPCO_FLASHCTL_AT_BUF1_LOAD	0x0253
#define SSB_CHIPCO_FLASHCTL_AT_BUF2_LOAD	0x0255
#define SSB_CHIPCO_FLASHCTL_AT_BUF1_COMPARE	0x0260
#define SSB_CHIPCO_FLASHCTL_AT_BUF2_COMPARE	0x0261
#define SSB_CHIPCO_FLASHCTL_AT_BUF1_REPROGRAM	0x0258
#define SSB_CHIPCO_FLASHCTL_AT_BUF2_REPROGRAM	0x0259

/* Status register bits for Atmel flashes */
#define SSB_CHIPCO_FLASHSTA_AT_READY	0x80
#define SSB_CHIPCO_FLASHSTA_AT_MISMATCH	0x40
#define SSB_CHIPCO_FLASHSTA_AT_ID	0x38
#define SSB_CHIPCO_FLASHSTA_AT_ID_SHIFT	3


/** OTP **/

/* OTP regions */
#define	SSB_CHIPCO_OTP_HW_REGION	SSB_CHIPCO_OTPS_HW_PROTECT
#define	SSB_CHIPCO_OTP_SW_REGION	SSB_CHIPCO_OTPS_SW_PROTECT
#define	SSB_CHIPCO_OTP_CID_REGION	SSB_CHIPCO_OTPS_CID_PROTECT

/* OTP regions (Byte offsets from otp size) */
#define	SSB_CHIPCO_OTP_SWLIM_OFF	(-8)
#define	SSB_CHIPCO_OTP_CIDBASE_OFF	0
#define	SSB_CHIPCO_OTP_CIDLIM_OFF	8

/* Predefined OTP words (Word offset from otp size) */
#define	SSB_CHIPCO_OTP_BOUNDARY_OFF	(-4)
#define	SSB_CHIPCO_OTP_HWSIGN_OFF	(-3)
#define	SSB_CHIPCO_OTP_SWSIGN_OFF	(-2)
#define	SSB_CHIPCO_OTP_CIDSIGN_OFF	(-1)

#define	SSB_CHIPCO_OTP_CID_OFF		0
#define	SSB_CHIPCO_OTP_PKG_OFF		1
#define	SSB_CHIPCO_OTP_FID_OFF		2
#define	SSB_CHIPCO_OTP_RSV_OFF		3
#define	SSB_CHIPCO_OTP_LIM_OFF		4

#define	SSB_CHIPCO_OTP_SIGNATURE	0x578A
#define	SSB_CHIPCO_OTP_MAGIC		0x4E56


struct ssb_device;
struct ssb_serial_port;

/* Data for the PMU, if available.
 * Check availability with ((struct ssb_chipcommon)->capabilities & SSB_CHIPCO_CAP_PMU)
 */
struct ssb_chipcommon_pmu {
	u8 rev;			/* PMU revision */
	u32 crystalfreq;	/* The active crystal frequency (in kHz) */
};

struct ssb_chipcommon {
	struct ssb_device *dev;
	u32 capabilities;
	u32 status;
	/* Fast Powerup Delay constant */
	u16 fast_pwrup_delay;
	spinlock_t gpio_lock;
	struct ssb_chipcommon_pmu pmu;
	u32 ticks_per_ms;
	u32 max_timer_ms;
};

static inline bool ssb_chipco_available(struct ssb_chipcommon *cc)
{
	return (cc->dev != NULL);
}

/* Register access */
#define chipco_read32(cc, offset)	ssb_read32((cc)->dev, offset)
#define chipco_write32(cc, offset, val)	ssb_write32((cc)->dev, offset, val)

#define chipco_mask32(cc, offset, mask) \
		chipco_write32(cc, offset, chipco_read32(cc, offset) & (mask))
#define chipco_set32(cc, offset, set) \
		chipco_write32(cc, offset, chipco_read32(cc, offset) | (set))
#define chipco_maskset32(cc, offset, mask, set) \
		chipco_write32(cc, offset, (chipco_read32(cc, offset) & (mask)) | (set))

extern void ssb_chipcommon_init(struct ssb_chipcommon *cc);

extern void ssb_chipco_suspend(struct ssb_chipcommon *cc);
extern void ssb_chipco_resume(struct ssb_chipcommon *cc);

extern void ssb_chipco_get_clockcpu(struct ssb_chipcommon *cc,
                                    u32 *plltype, u32 *n, u32 *m);
extern void ssb_chipco_get_clockcontrol(struct ssb_chipcommon *cc,
					u32 *plltype, u32 *n, u32 *m);
extern void ssb_chipco_timing_init(struct ssb_chipcommon *cc,
				   unsigned long ns_per_cycle);

enum ssb_clkmode {
	SSB_CLKMODE_SLOW,
	SSB_CLKMODE_FAST,
	SSB_CLKMODE_DYNAMIC,
};

extern void ssb_chipco_set_clockmode(struct ssb_chipcommon *cc,
				     enum ssb_clkmode mode);

extern u32 ssb_chipco_watchdog_timer_set(struct ssb_chipcommon *cc, u32 ticks);

void ssb_chipco_irq_mask(struct ssb_chipcommon *cc, u32 mask, u32 value);

u32 ssb_chipco_irq_status(struct ssb_chipcommon *cc, u32 mask);

/* Chipcommon GPIO pin access. */
u32 ssb_chipco_gpio_in(struct ssb_chipcommon *cc, u32 mask);
u32 ssb_chipco_gpio_out(struct ssb_chipcommon *cc, u32 mask, u32 value);
u32 ssb_chipco_gpio_outen(struct ssb_chipcommon *cc, u32 mask, u32 value);
u32 ssb_chipco_gpio_control(struct ssb_chipcommon *cc, u32 mask, u32 value);
u32 ssb_chipco_gpio_intmask(struct ssb_chipcommon *cc, u32 mask, u32 value);
u32 ssb_chipco_gpio_polarity(struct ssb_chipcommon *cc, u32 mask, u32 value);
u32 ssb_chipco_gpio_pullup(struct ssb_chipcommon *cc, u32 mask, u32 value);
u32 ssb_chipco_gpio_pulldown(struct ssb_chipcommon *cc, u32 mask, u32 value);

#ifdef CONFIG_SSB_SERIAL
extern int ssb_chipco_serial_init(struct ssb_chipcommon *cc,
				  struct ssb_serial_port *ports);
#endif /* CONFIG_SSB_SERIAL */

/* PMU support */
extern void ssb_pmu_init(struct ssb_chipcommon *cc);

enum ssb_pmu_ldo_volt_id {
	LDO_PAREF = 0,
	LDO_VOLT1,
	LDO_VOLT2,
	LDO_VOLT3,
};

void ssb_pmu_set_ldo_voltage(struct ssb_chipcommon *cc,
			     enum ssb_pmu_ldo_volt_id id, u32 voltage);
void ssb_pmu_set_ldo_paref(struct ssb_chipcommon *cc, bool on);
void ssb_pmu_spuravoid_pllupdate(struct ssb_chipcommon *cc, int spuravoid);

#endif /* LINUX_SSB_CHIPCO_H_ */