Release 4.7 drivers/atm/idt77105.h
/* drivers/atm/idt77105.h - IDT77105 (PHY) declarations */
/* Written 1999 by Greg Banks, NEC Australia <gnb@linuxfan.com>. Based on suni.h */
#ifndef DRIVER_ATM_IDT77105_H
#define DRIVER_ATM_IDT77105_H
#include <linux/atmdev.h>
#include <linux/atmioc.h>
/* IDT77105 registers */
#define IDT77105_MCR 0x0
/* Master Control Register */
#define IDT77105_ISTAT 0x1
/* Interrupt Status */
#define IDT77105_DIAG 0x2
/* Diagnostic Control */
#define IDT77105_LEDHEC 0x3
/* LED Driver & HEC Status/Control */
#define IDT77105_CTRLO 0x4
/* Low Byte Counter Register */
#define IDT77105_CTRHI 0x5
/* High Byte Counter Register */
#define IDT77105_CTRSEL 0x6
/* Counter Register Read Select */
/* IDT77105 register values */
/* MCR */
#define IDT77105_MCR_UPLO 0x80
/* R/W, User Prog'le Output Latch */
#define IDT77105_MCR_DREC 0x40
/* R/W, Discard Receive Error Cells */
#define IDT77105_MCR_ECEIO 0x20
/* R/W, Enable Cell Error Interrupts
* Only */
#define IDT77105_MCR_TDPC 0x10
/* R/W, Transmit Data Parity Check */
#define IDT77105_MCR_DRIC 0x08
/* R/W, Discard Received Idle Cells */
#define IDT77105_MCR_HALTTX 0x04
/* R/W, Halt Tx */
#define IDT77105_MCR_UMODE 0x02
/* R/W, Utopia (cell/byte) Mode */
#define IDT77105_MCR_EIP 0x01
/* R/W, Enable Interrupt Pin */
/* ISTAT */
#define IDT77105_ISTAT_GOODSIG 0x40
/* R, Good Signal Bit */
#define IDT77105_ISTAT_HECERR 0x20
/* sticky, HEC Error*/
#define IDT77105_ISTAT_SCR 0x10
/* sticky, Short Cell Received */
#define IDT77105_ISTAT_TPE 0x08
/* sticky, Transmit Parity Error */
#define IDT77105_ISTAT_RSCC 0x04
/* sticky, Rx Signal Condition Change */
#define IDT77105_ISTAT_RSE 0x02
/* sticky, Rx Symbol Error */
#define IDT77105_ISTAT_RFO 0x01
/* sticky, Rx FIFO Overrun */
/* DIAG */
#define IDT77105_DIAG_FTD 0x80
/* R/W, Force TxClav deassert */
#define IDT77105_DIAG_ROS 0x40
/* R/W, RxClav operation select */
#define IDT77105_DIAG_MPCS 0x20
/* R/W, Multi-PHY config'n select */
#define IDT77105_DIAG_RFLUSH 0x10
/* R/W, clear receive FIFO */
#define IDT77105_DIAG_ITPE 0x08
/* R/W, Insert Tx payload error */
#define IDT77105_DIAG_ITHE 0x04
/* R/W, Insert Tx HEC error */
#define IDT77105_DIAG_UMODE 0x02
/* R/W, Utopia (cell/byte) Mode */
#define IDT77105_DIAG_LCMASK 0x03
/* R/W, Loopback Control */
#define IDT77105_DIAG_LC_NORMAL 0x00
/* Receive from network */
#define IDT77105_DIAG_LC_PHY_LOOPBACK 0x02
#define IDT77105_DIAG_LC_LINE_LOOPBACK 0x03
/* LEDHEC */
#define IDT77105_LEDHEC_DRHC 0x40
/* R/W, Disable Rx HEC check */
#define IDT77105_LEDHEC_DTHC 0x20
/* R/W, Disable Tx HEC calculation */
#define IDT77105_LEDHEC_RPWMASK 0x18
/* R/W, RxRef pulse width select */
#define IDT77105_LEDHEC_TFS 0x04
/* R, Tx FIFO Status (1=empty) */
#define IDT77105_LEDHEC_TLS 0x02
/* R, Tx LED Status (1=lit) */
#define IDT77105_LEDHEC_RLS 0x01
/* R, Rx LED Status (1=lit) */
#define IDT77105_LEDHEC_RPW_1 0x00
/* RxRef active for 1 RxClk cycle */
#define IDT77105_LEDHEC_RPW_2 0x08
/* RxRef active for 2 RxClk cycle */
#define IDT77105_LEDHEC_RPW_4 0x10
/* RxRef active for 4 RxClk cycle */
#define IDT77105_LEDHEC_RPW_8 0x18
/* RxRef active for 8 RxClk cycle */
/* CTRSEL */
#define IDT77105_CTRSEL_SEC 0x08
/* W, Symbol Error Counter */
#define IDT77105_CTRSEL_TCC 0x04
/* W, Tx Cell Counter */
#define IDT77105_CTRSEL_RCC 0x02
/* W, Rx Cell Counter */
#define IDT77105_CTRSEL_RHEC 0x01
/* W, Rx HEC Error Counter */
#ifdef __KERNEL__
int idt77105_init(struct atm_dev *dev);
#endif
/*
* Tunable parameters
*/
/* Time between samples of the hardware cell counters. Should be <= 1 sec */
#define IDT77105_STATS_TIMER_PERIOD (HZ)
/* Time between checks to see if the signal has been found again */
#define IDT77105_RESTART_TIMER_PERIOD (5 * HZ)
#endif
Overall Contributors
| Person | Tokens | Prop | Commits | CommitProp |
pre-git | pre-git | 276 | 98.22% | 1 | 50.00% |
chas williams | chas williams | 5 | 1.78% | 1 | 50.00% |
| Total | 281 | 100.00% | 2 | 100.00% |
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.