Release 4.7 drivers/i2c/busses/i2c-rk3x.c
/*
* Driver for I2C adapter in Rockchip RK3xxx SoC
*
* Max Schwarz <max.schwarz@online.de>
* based on the patches by Rockchip Inc.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/i2c.h>
#include <linux/interrupt.h>
#include <linux/errno.h>
#include <linux/err.h>
#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/of_address.h>
#include <linux/of_irq.h>
#include <linux/spinlock.h>
#include <linux/clk.h>
#include <linux/wait.h>
#include <linux/mfd/syscon.h>
#include <linux/regmap.h>
#include <linux/math64.h>
/* Register Map */
#define REG_CON 0x00
/* control register */
#define REG_CLKDIV 0x04
/* clock divisor register */
#define REG_MRXADDR 0x08
/* slave address for REGISTER_TX */
#define REG_MRXRADDR 0x0c
/* slave register address for REGISTER_TX */
#define REG_MTXCNT 0x10
/* number of bytes to be transmitted */
#define REG_MRXCNT 0x14
/* number of bytes to be received */
#define REG_IEN 0x18
/* interrupt enable */
#define REG_IPD 0x1c
/* interrupt pending */
#define REG_FCNT 0x20
/* finished count */
/* Data buffer offsets */
#define TXBUFFER_BASE 0x100
#define RXBUFFER_BASE 0x200
/* REG_CON bits */
#define REG_CON_EN BIT(0)
enum {
REG_CON_MOD_TX = 0, /* transmit data */
REG_CON_MOD_REGISTER_TX, /* select register and restart */
REG_CON_MOD_RX, /* receive data */
REG_CON_MOD_REGISTER_RX, /* broken: transmits read addr AND writes
* register addr */
};
#define REG_CON_MOD(mod) ((mod) << 1)
#define REG_CON_MOD_MASK (BIT(1) | BIT(2))
#define REG_CON_START BIT(3)
#define REG_CON_STOP BIT(4)
#define REG_CON_LASTACK BIT(5)
/* 1: send NACK after last received byte */
#define REG_CON_ACTACK BIT(6)
/* 1: stop if NACK is received */
/* REG_MRXADDR bits */
#define REG_MRXADDR_VALID(x) BIT(24 + (x))
/* [x*8+7:x*8] of MRX[R]ADDR valid */
/* REG_IEN/REG_IPD bits */
#define REG_INT_BTF BIT(0)
/* a byte was transmitted */
#define REG_INT_BRF BIT(1)
/* a byte was received */
#define REG_INT_MBTF BIT(2)
/* master data transmit finished */
#define REG_INT_MBRF BIT(3)
/* master data receive finished */
#define REG_INT_START BIT(4)
/* START condition generated */
#define REG_INT_STOP BIT(5)
/* STOP condition generated */
#define REG_INT_NAKRCV BIT(6)
/* NACK received */
#define REG_INT_ALL 0x7f
/* Constants */
#define WAIT_TIMEOUT 1000
/* ms */
#define DEFAULT_SCL_RATE (100 * 1000)
/* Hz */
enum rk3x_i2c_state {
STATE_IDLE,
STATE_START,
STATE_READ,
STATE_WRITE,
STATE_STOP
};
/**
* @grf_offset: offset inside the grf regmap for setting the i2c type
*/
struct rk3x_i2c_soc_data {
int grf_offset;
};
struct rk3x_i2c {
struct i2c_adapter adap;
struct device *dev;
struct rk3x_i2c_soc_data *soc_data;
/* Hardware resources */
void __iomem *regs;
struct clk *clk;
struct notifier_block clk_rate_nb;
/* Settings */
struct i2c_timings t;
/* Synchronization & notification */
spinlock_t lock;
wait_queue_head_t wait;
bool busy;
/* Current message */
struct i2c_msg *msg;
u8 addr;
unsigned int mode;
bool is_last_msg;
/* I2C state machine */
enum rk3x_i2c_state state;
unsigned int processed; /* sent/received bytes */
int error;
};
static inline void i2c_writel(struct rk3x_i2c *i2c, u32 value,
unsigned int offset)
{
writel(value, i2c->regs + offset);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| max schwarz | max schwarz | 30 | 100.00% | 1 | 100.00% |
| Total | 30 | 100.00% | 1 | 100.00% |
static inline u32 i2c_readl(struct rk3x_i2c *i2c, unsigned int offset)
{
return readl(i2c->regs + offset);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| max schwarz | max schwarz | 26 | 100.00% | 1 | 100.00% |
| Total | 26 | 100.00% | 1 | 100.00% |
/* Reset all interrupt pending bits */
static inline void rk3x_i2c_clean_ipd(struct rk3x_i2c *i2c)
{
i2c_writel(i2c, REG_INT_ALL, REG_IPD);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| max schwarz | max schwarz | 21 | 100.00% | 1 | 100.00% |
| Total | 21 | 100.00% | 1 | 100.00% |
/**
* Generate a START condition, which triggers a REG_INT_START interrupt.
*/
static void rk3x_i2c_start(struct rk3x_i2c *i2c)
{
u32 val;
rk3x_i2c_clean_ipd(i2c);
i2c_writel(i2c, REG_INT_START, REG_IEN);
/* enable adapter with correct mode, send START condition */
val = REG_CON_EN | REG_CON_MOD(i2c->mode) | REG_CON_START;
/* if we want to react to NACK, set ACTACK bit */
if (!(i2c->msg->flags & I2C_M_IGNORE_NAK))
val |= REG_CON_ACTACK;
i2c_writel(i2c, val, REG_CON);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| max schwarz | max schwarz | 69 | 100.00% | 1 | 100.00% |
| Total | 69 | 100.00% | 1 | 100.00% |
/**
* Generate a STOP condition, which triggers a REG_INT_STOP interrupt.
*
* @error: Error code to return in rk3x_i2c_xfer
*/
static void rk3x_i2c_stop(struct rk3x_i2c *i2c, int error)
{
unsigned int ctrl;
i2c->processed = 0;
i2c->msg = NULL;
i2c->error = error;
if (i2c->is_last_msg) {
/* Enable stop interrupt */
i2c_writel(i2c, REG_INT_STOP, REG_IEN);
i2c->state = STATE_STOP;
ctrl = i2c_readl(i2c, REG_CON);
ctrl |= REG_CON_STOP;
i2c_writel(i2c, ctrl, REG_CON);
} else {
/* Signal rk3x_i2c_xfer to start the next message. */
i2c->busy = false;
i2c->state = STATE_IDLE;
/*
* The HW is actually not capable of REPEATED START. But we can
* get the intended effect by resetting its internal state
* and issuing an ordinary START.
*/
i2c_writel(i2c, 0, REG_CON);
/* signal that we are finished with the current msg */
wake_up(&i2c->wait);
}
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| max schwarz | max schwarz | 117 | 100.00% | 1 | 100.00% |
| Total | 117 | 100.00% | 1 | 100.00% |
/**
* Setup a read according to i2c->msg
*/
static void rk3x_i2c_prepare_read(struct rk3x_i2c *i2c)
{
unsigned int len = i2c->msg->len - i2c->processed;
u32 con;
con = i2c_readl(i2c, REG_CON);
/*
* The hw can read up to 32 bytes at a time. If we need more than one
* chunk, send an ACK after the last byte of the current chunk.
*/
if (len > 32) {
len = 32;
con &= ~REG_CON_LASTACK;
} else {
con |= REG_CON_LASTACK;
}
/* make sure we are in plain RX mode if we read a second chunk */
if (i2c->processed != 0) {
con &= ~REG_CON_MOD_MASK;
con |= REG_CON_MOD(REG_CON_MOD_RX);
}
i2c_writel(i2c, con, REG_CON);
i2c_writel(i2c, len, REG_MRXCNT);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| max schwarz | max schwarz | 103 | 100.00% | 1 | 100.00% |
| Total | 103 | 100.00% | 1 | 100.00% |
/**
* Fill the transmit buffer with data from i2c->msg
*/
static void rk3x_i2c_fill_transmit_buf(struct rk3x_i2c *i2c)
{
unsigned int i, j;
u32 cnt = 0;
u32 val;
u8 byte;
for (i = 0; i < 8; ++i) {
val = 0;
for (j = 0; j < 4; ++j) {
if ((i2c->processed == i2c->msg->len) && (cnt != 0))
break;
if (i2c->processed == 0 && cnt == 0)
byte = (i2c->addr & 0x7f) << 1;
else
byte = i2c->msg->buf[i2c->processed++];
val |= byte << (j * 8);
cnt++;
}
i2c_writel(i2c, val, TXBUFFER_BASE + 4 * i);
if (i2c->processed == i2c->msg->len)
break;
}
i2c_writel(i2c, cnt, REG_MTXCNT);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| max schwarz | max schwarz | 162 | 95.29% | 1 | 50.00% |
| alexandru m stan | alexandru m stan | 8 | 4.71% | 1 | 50.00% |
| Total | 170 | 100.00% | 2 | 100.00% |
/* IRQ handlers for individual states */
static void rk3x_i2c_handle_start(struct rk3x_i2c *i2c, unsigned int ipd)
{
if (!(ipd & REG_INT_START)) {
rk3x_i2c_stop(i2c, -EIO);
dev_warn(i2c->dev, "unexpected irq in START: 0x%x\n", ipd);
rk3x_i2c_clean_ipd(i2c);
return;
}
/* ack interrupt */
i2c_writel(i2c, REG_INT_START, REG_IPD);
/* disable start bit */
i2c_writel(i2c, i2c_readl(i2c, REG_CON) & ~REG_CON_START, REG_CON);
/* enable appropriate interrupts and transition */
if (i2c->mode == REG_CON_MOD_TX) {
i2c_writel(i2c, REG_INT_MBTF | REG_INT_NAKRCV, REG_IEN);
i2c->state = STATE_WRITE;
rk3x_i2c_fill_transmit_buf(i2c);
} else {
/* in any other case, we are going to be reading. */
i2c_writel(i2c, REG_INT_MBRF | REG_INT_NAKRCV, REG_IEN);
i2c->state = STATE_READ;
rk3x_i2c_prepare_read(i2c);
}
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| max schwarz | max schwarz | 138 | 100.00% | 1 | 100.00% |
| Total | 138 | 100.00% | 1 | 100.00% |
static void rk3x_i2c_handle_write(struct rk3x_i2c *i2c, unsigned int ipd)
{
if (!(ipd & REG_INT_MBTF)) {
rk3x_i2c_stop(i2c, -EIO);
dev_err(i2c->dev, "unexpected irq in WRITE: 0x%x\n", ipd);
rk3x_i2c_clean_ipd(i2c);
return;
}
/* ack interrupt */
i2c_writel(i2c, REG_INT_MBTF, REG_IPD);
/* are we finished? */
if (i2c->processed == i2c->msg->len)
rk3x_i2c_stop(i2c, i2c->error);
else
rk3x_i2c_fill_transmit_buf(i2c);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| max schwarz | max schwarz | 89 | 100.00% | 1 | 100.00% |
| Total | 89 | 100.00% | 1 | 100.00% |
static void rk3x_i2c_handle_read(struct rk3x_i2c *i2c, unsigned int ipd)
{
unsigned int i;
unsigned int len = i2c->msg->len - i2c->processed;
u32 uninitialized_var(val);
u8 byte;
/* we only care for MBRF here. */
if (!(ipd & REG_INT_MBRF))
return;
/* ack interrupt */
i2c_writel(i2c, REG_INT_MBRF, REG_IPD);
/* Can only handle a maximum of 32 bytes at a time */
if (len > 32)
len = 32;
/* read the data from receive buffer */
for (i = 0; i < len; ++i) {
if (i % 4 == 0)
val = i2c_readl(i2c, RXBUFFER_BASE + (i / 4) * 4);
byte = (val >> ((i % 4) * 8)) & 0xff;
i2c->msg->buf[i2c->processed++] = byte;
}
/* are we finished? */
if (i2c->processed == i2c->msg->len)
rk3x_i2c_stop(i2c, i2c->error);
else
rk3x_i2c_prepare_read(i2c);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| max schwarz | max schwarz | 164 | 93.71% | 1 | 50.00% |
| addy ke | addy ke | 11 | 6.29% | 1 | 50.00% |
| Total | 175 | 100.00% | 2 | 100.00% |
static void rk3x_i2c_handle_stop(struct rk3x_i2c *i2c, unsigned int ipd)
{
unsigned int con;
if (!(ipd & REG_INT_STOP)) {
rk3x_i2c_stop(i2c, -EIO);
dev_err(i2c->dev, "unexpected irq in STOP: 0x%x\n", ipd);
rk3x_i2c_clean_ipd(i2c);
return;
}
/* ack interrupt */
i2c_writel(i2c, REG_INT_STOP, REG_IPD);
/* disable STOP bit */
con = i2c_readl(i2c, REG_CON);
con &= ~REG_CON_STOP;
i2c_writel(i2c, con, REG_CON);
i2c->busy = false;
i2c->state = STATE_IDLE;
/* signal rk3x_i2c_xfer that we are finished */
wake_up(&i2c->wait);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| max schwarz | max schwarz | 110 | 100.00% | 1 | 100.00% |
| Total | 110 | 100.00% | 1 | 100.00% |
static irqreturn_t rk3x_i2c_irq(int irqno, void *dev_id)
{
struct rk3x_i2c *i2c = dev_id;
unsigned int ipd;
spin_lock(&i2c->lock);
ipd = i2c_readl(i2c, REG_IPD);
if (i2c->state == STATE_IDLE) {
dev_warn(i2c->dev, "irq in STATE_IDLE, ipd = 0x%x\n", ipd);
rk3x_i2c_clean_ipd(i2c);
goto out;
}
dev_dbg(i2c->dev, "IRQ: state %d, ipd: %x\n", i2c->state, ipd);
/* Clean interrupt bits we don't care about */
ipd &= ~(REG_INT_BRF | REG_INT_BTF);
if (ipd & REG_INT_NAKRCV) {
/*
* We got a NACK in the last operation. Depending on whether
* IGNORE_NAK is set, we have to stop the operation and report
* an error.
*/
i2c_writel(i2c, REG_INT_NAKRCV, REG_IPD);
ipd &= ~REG_INT_NAKRCV;
if (!(i2c->msg->flags & I2C_M_IGNORE_NAK))
rk3x_i2c_stop(i2c, -ENXIO);
}
/* is there anything left to handle? */
if ((ipd & REG_INT_ALL) == 0)
goto out;
switch (i2c->state) {
case STATE_START:
rk3x_i2c_handle_start(i2c, ipd);
break;
case STATE_WRITE:
rk3x_i2c_handle_write(i2c, ipd);
break;
case STATE_READ:
rk3x_i2c_handle_read(i2c, ipd);
break;
case STATE_STOP:
rk3x_i2c_handle_stop(i2c, ipd);
break;
case STATE_IDLE:
break;
}
out:
spin_unlock(&i2c->lock);
return IRQ_HANDLED;
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| max schwarz | max schwarz | 218 | 98.20% | 1 | 50.00% |
| addy ke | addy ke | 4 | 1.80% | 1 | 50.00% |
| Total | 222 | 100.00% | 2 | 100.00% |
/**
* Calculate divider values for desired SCL frequency
*
* @clk_rate: I2C input clock rate
* @t: Known I2C timing information.
* @div_low: Divider output for low
* @div_high: Divider output for high
*
* Returns: 0 on success, -EINVAL if the goal SCL rate is too slow. In that case
* a best-effort divider value is returned in divs. If the target rate is
* too high, we silently use the highest possible rate.
*/
static int rk3x_i2c_calc_divs(unsigned long clk_rate,
struct i2c_timings *t,
unsigned long *div_low,
unsigned long *div_high)
{
unsigned long spec_min_low_ns, spec_min_high_ns;
unsigned long spec_setup_start, spec_max_data_hold_ns;
unsigned long data_hold_buffer_ns;
unsigned long min_low_ns, min_high_ns;
unsigned long max_low_ns, min_total_ns;
unsigned long clk_rate_khz, scl_rate_khz;
unsigned long min_low_div, min_high_div;
unsigned long max_low_div;
unsigned long min_div_for_hold, min_total_div;
unsigned long extra_div, extra_low_div, ideal_low_div;
int ret = 0;
/* Only support standard-mode and fast-mode */
if (WARN_ON(t->bus_freq_hz > 400000))
t->bus_freq_hz = 400000;
/* prevent scl_rate_khz from becoming 0 */
if (WARN_ON(t->bus_freq_hz < 1000))
t->bus_freq_hz = 1000;
/*
* min_low_ns: The minimum number of ns we need to hold low to
* meet I2C specification, should include fall time.
* min_high_ns: The minimum number of ns we need to hold high to
* meet I2C specification, should include rise time.
* max_low_ns: The maximum number of ns we can hold low to meet
* I2C specification.
*
* Note: max_low_ns should be (maximum data hold time * 2 - buffer)
* This is because the i2c host on Rockchip holds the data line
* for half the low time.
*/
if (t->bus_freq_hz <= 100000) {
/* Standard-mode */
spec_min_low_ns = 4700;
spec_setup_start = 4700;
spec_min_high_ns = 4000;
spec_max_data_hold_ns = 3450;
data_hold_buffer_ns = 50;
} else {
/* Fast-mode */
spec_min_low_ns = 1300;
spec_setup_start = 600;
spec_min_high_ns = 600;
spec_max_data_hold_ns = 900;
data_hold_buffer_ns = 50;
}
min_high_ns = t->scl_rise_ns + spec_min_high_ns;
/*
* Timings for repeated start:
* - controller appears to drop SDA at .875x (7/8) programmed clk high.
* - controller appears to keep SCL high for 2x programmed clk high.
*
* We need to account for those rules in picking our "high" time so
* we meet tSU;STA and tHD;STA times.
*/
min_high_ns = max(min_high_ns,
DIV_ROUND_UP((t->scl_rise_ns + spec_setup_start) * 1000, 875));
min_high_ns = max(min_high_ns,
DIV_ROUND_UP((t->scl_rise_ns + spec_setup_start +
t->sda_fall_ns + spec_min_high_ns), 2));
min_low_ns = t->scl_fall_ns + spec_min_low_ns;
max_low_ns = spec_max_data_hold_ns * 2 - data_hold_buffer_ns;
min_total_ns = min_low_ns + min_high_ns;
/* Adjust to avoid overflow */
clk_rate_khz = DIV_ROUND_UP(clk_rate, 1000);
scl_rate_khz = t->bus_freq_hz / 1000;
/*
* We need the total div to be >= this number
* so we don't clock too fast.
*/
min_total_div = DIV_ROUND_UP(clk_rate_khz, scl_rate_khz * 8);
/* These are the min dividers needed for min hold times. */
min_low_div = DIV_ROUND_UP(clk_rate_khz * min_low_ns, 8 * 1000000);
min_high_div = DIV_ROUND_UP(clk_rate_khz * min_high_ns, 8 * 1000000);
min_div_for_hold = (min_low_div + min_high_div);
/*
* This is the maximum divider so we don't go over the maximum.
* We don't round up here (we round down) since this is a maximum.
*/
max_low_div = clk_rate_khz * max_low_ns / (8 * 1000000);
if (min_low_div > max_low_div) {
WARN_ONCE(true,
"Conflicting, min_low_div %lu, max_low_div %lu\n",
min_low_div, max_low_div);
max_low_div = min_low_div;
}
if (min_div_for_hold > min_total_div) {
/*
* Time needed to meet hold requirements is important.
* Just use that.
*/
*div_low = min_low_div;
*div_high = min_high_div;
} else {
/*
* We've got to distribute some time among the low and high
* so we don't run too fast.
*/
extra_div = min_total_div - min_div_for_hold;
/*
* We'll try to split things up perfectly evenly,
* biasing slightly towards having a higher div
* for low (spend more time low).
*/
ideal_low_div = DIV_ROUND_UP(clk_rate_khz * min_low_ns,
scl_rate_khz * 8 * min_total_ns);
/* Don't allow it to go over the maximum */
if (ideal_low_div > max_low_div)
ideal_low_div = max_low_div;
/*
* Handle when the ideal low div is going to take up
* more than we have.
*/
if (ideal_low_div > min_low_div + extra_div)
ideal_low_div = min_low_div + extra_div;
/* Give low the "ideal" and give high whatever extra is left */
extra_low_div = ideal_low_div - min_low_div;
*div_low = ideal_low_div;
*div_high = min_high_div + (extra_div - extra_low_div);
}
/*
* Adjust to the fact that the hardware has an implicit "+1".
* NOTE: Above calculations always produce div_low > 0 and div_high > 0.
*/
*div_low = *div_low - 1;
*div_high = *div_high - 1;
/* Maximum divider supported by hw is 0xffff */
if (*div_low > 0xffff) {
*div_low = 0xffff;
ret = -EINVAL;
}
if (*div_high > 0xffff) {
*div_high = 0xffff;
ret = -EINVAL;
}
return ret;
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| addy ke | addy ke | 380 | 74.07% | 2 | 40.00% |
| douglas anderson | douglas anderson | 57 | 11.11% | 1 | 20.00% |
| max schwarz | max schwarz | 44 | 8.58% | 1 | 20.00% |
| david wu | david wu | 32 | 6.24% | 1 | 20.00% |
| Total | 513 | 100.00% | 5 | 100.00% |
static void rk3x_i2c_adapt_div(struct rk3x_i2c *i2c, unsigned long clk_rate)
{
struct i2c_timings *t = &i2c->t;
unsigned long div_low, div_high;
u64 t_low_ns, t_high_ns;
int ret;
ret = rk3x_i2c_calc_divs(clk_rate, t, &div_low, &div_high);
WARN_ONCE(ret != 0, "Could not reach SCL freq %u", t->bus_freq_hz);
clk_enable(i2c->clk);
i2c_writel(i2c, (div_high << 16) | (div_low & 0xffff), REG_CLKDIV);
clk_disable(i2c->clk);
t_low_ns = div_u64(((u64)div_low + 1) * 8 * 1000000000, clk_rate);
t_high_ns = div_u64(((u64)div_high + 1) * 8 * 1000000000, clk_rate);
dev_dbg(i2c->dev,
"CLK %lukhz, Req %uns, Act low %lluns high %lluns\n",
clk_rate / 1000,
1000000000 / t->bus_freq_hz,
t_low_ns, t_high_ns);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| addy ke | addy ke | 78 | 47.85% | 2 | 40.00% |
| max schwarz | max schwarz | 70 | 42.94% | 2 | 40.00% |
| david wu | david wu | 15 | 9.20% | 1 | 20.00% |
| Total | 163 | 100.00% | 5 | 100.00% |
/**
* rk3x_i2c_clk_notifier_cb - Clock rate change callback
* @nb: Pointer to notifier block
* @event: Notification reason
* @data: Pointer to notification data object
*
* The callback checks whether a valid bus frequency can be generated after the
* change. If so, the change is acknowledged, otherwise the change is aborted.
* New dividers are written to the HW in the pre- or post change notification
* depending on the scaling direction.
*
* Code adapted from i2c-cadence.c.
*
* Return: NOTIFY_STOP if the rate change should be aborted, NOTIFY_OK
* to acknowedge the change, NOTIFY_DONE if the notification is
* considered irrelevant.
*/
static int rk3x_i2c_clk_notifier_cb(struct notifier_block *nb, unsigned long
event, void *data)
{
struct clk_notifier_data *ndata = data;
struct rk3x_i2c *i2c = container_of(nb, struct rk3x_i2c, clk_rate_nb);
unsigned long div_low, div_high;
switch (event) {
case PRE_RATE_CHANGE:
if (rk3x_i2c_calc_divs(ndata->new_rate, &i2c->t,
&div_low, &div_high) != 0)
return NOTIFY_STOP;
/* scale up */
if (ndata->new_rate > ndata->old_rate)
rk3x_i2c_adapt_div(i2c, ndata->new_rate);
return NOTIFY_OK;
case POST_RATE_CHANGE:
/* scale down */
if (ndata->new_rate < ndata->old_rate)
rk3x_i2c_adapt_div(i2c, ndata->new_rate);
return NOTIFY_OK;
case ABORT_RATE_CHANGE:
/* scale up */
if (ndata->new_rate > ndata->old_rate)
rk3x_i2c_adapt_div(i2c, ndata->old_rate);
return NOTIFY_OK;
default:
return NOTIFY_DONE;
}
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| max schwarz | max schwarz | 155 | 96.88% | 2 | 40.00% |
| addy ke | addy ke | 3 | 1.88% | 2 | 40.00% |
| david wu | david wu | 2 | 1.25% | 1 | 20.00% |
| Total | 160 | 100.00% | 5 | 100.00% |
/**
* Setup I2C registers for an I2C operation specified by msgs, num.
*
* Must be called with i2c->lock held.
*
* @msgs: I2C msgs to process
* @num: Number of msgs
*
* returns: Number of I2C msgs processed or negative in case of error
*/
static int rk3x_i2c_setup(struct rk3x_i2c *i2c, struct i2c_msg *msgs, int num)
{
u32 addr = (msgs[0].addr & 0x7f) << 1;
int ret = 0;
/*
* The I2C adapter can issue a small (len < 4) write packet before
* reading. This speeds up SMBus-style register reads.
* The MRXADDR/MRXRADDR hold the slave address and the slave register
* address in this case.
*/
if (num >= 2 && msgs[0].len < 4 &&
!(msgs[0].flags & I2C_M_RD) && (msgs[1].flags & I2C_M_RD)) {
u32 reg_addr = 0;
int i;
dev_dbg(i2c->dev, "Combined write/read from addr 0x%x\n",
addr >> 1);
/* Fill MRXRADDR with the register address(es) */
for (i = 0; i < msgs[0].len; ++i) {
reg_addr |= msgs[0].buf[i] << (i * 8);
reg_addr |= REG_MRXADDR_VALID(i);
}
/* msgs[0] is handled by hw. */
i2c->msg = &msgs[1];
i2c->mode = REG_CON_MOD_REGISTER_TX;
i2c_writel(i2c, addr | REG_MRXADDR_VALID(0), REG_MRXADDR);
i2c_writel(i2c, reg_addr, REG_MRXRADDR);
ret = 2;
} else {
/*
* We'll have to do it the boring way and process the msgs
* one-by-one.
*/
if (msgs[0].flags & I2C_M_RD) {
addr |= 1; /* set read bit */
/*
* We have to transmit the slave addr first. Use
* MOD_REGISTER_TX for that purpose.
*/
i2c->mode = REG_CON_MOD_REGISTER_TX;
i2c_writel(i2c, addr | REG_MRXADDR_VALID(0),
REG_MRXADDR);
i2c_writel(i2c, 0, REG_MRXRADDR);
} else {
i2c->mode = REG_CON_MOD_TX;
}
i2c->msg = &msgs[0];
ret = 1;
}
i2c->addr = msgs[0].addr;
i2c->busy = true;
i2c->state = STATE_START;
i2c->processed = 0;
i2c->error = 0;
rk3x_i2c_clean_ipd(i2c);
return ret;
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| max schwarz | max schwarz | 310 | 100.00% | 1 | 100.00% |
| Total | 310 | 100.00% | 1 | 100.00% |
static int rk3x_i2c_xfer(struct i2c_adapter *adap,
struct i2c_msg *msgs, int num)
{
struct rk3x_i2c *i2c = (struct rk3x_i2c *)adap->algo_data;
unsigned long timeout, flags;
int ret = 0;
int i;
spin_lock_irqsave(&i2c->lock, flags);
clk_enable(i2c->clk);
i2c->is_last_msg = false;
/*
* Process msgs. We can handle more than one message at once (see
* rk3x_i2c_setup()).
*/
for (i = 0; i < num; i += ret) {
ret = rk3x_i2c_setup(i2c, msgs + i, num - i);
if (ret < 0) {
dev_err(i2c->dev, "rk3x_i2c_setup() failed\n");
break;
}
if (i + ret >= num)
i2c->is_last_msg = true;
spin_unlock_irqrestore(&i2c->lock, flags);
rk3x_i2c_start(i2c);
timeout = wait_event_timeout(i2c->wait, !i2c->busy,
msecs_to_jiffies(WAIT_TIMEOUT));
spin_lock_irqsave(&i2c->lock, flags);
if (timeout == 0) {
dev_err(i2c->dev, "timeout, ipd: 0x%02x, state: %d\n",
i2c_readl(i2c, REG_IPD), i2c->state);
/* Force a STOP condition without interrupt */
i2c_writel(i2c, 0, REG_IEN);
i2c_writel(i2c, REG_CON_EN | REG_CON_STOP, REG_CON);
i2c->state = STATE_IDLE;
ret = -ETIMEDOUT;
break;
}
if (i2c->error) {
ret = i2c->error;
break;
}
}
clk_disable(i2c->clk);
spin_unlock_irqrestore(&i2c->lock, flags);
return ret < 0 ? ret : num;
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| max schwarz | max schwarz | 274 | 97.86% | 1 | 50.00% |
| dmitry torokhov | dmitry torokhov | 6 | 2.14% | 1 | 50.00% |
| Total | 280 | 100.00% | 2 | 100.00% |
static u32 rk3x_i2c_func(struct i2c_adapter *adap)
{
return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL | I2C_FUNC_PROTOCOL_MANGLING;
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| max schwarz | max schwarz | 18 | 100.00% | 1 | 100.00% |
| Total | 18 | 100.00% | 1 | 100.00% |
static const struct i2c_algorithm rk3x_i2c_algorithm = {
.master_xfer = rk3x_i2c_xfer,
.functionality = rk3x_i2c_func,
};
static struct rk3x_i2c_soc_data soc_data[3] = {
{ .grf_offset = 0x154 }, /* rk3066 */
{ .grf_offset = 0x0a4 }, /* rk3188 */
{ .grf_offset = -1 }, /* no I2C switching needed */
};
static const struct of_device_id rk3x_i2c_match[] = {
{ .compatible = "rockchip,rk3066-i2c", .data = (void *)&soc_data[0] },
{ .compatible = "rockchip,rk3188-i2c", .data = (void *)&soc_data[1] },
{ .compatible = "rockchip,rk3228-i2c", .data = (void *)&soc_data[2] },
{ .compatible = "rockchip,rk3288-i2c", .data = (void *)&soc_data[2] },
{},
};
MODULE_DEVICE_TABLE(of, rk3x_i2c_match);
static int rk3x_i2c_probe(struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
const struct of_device_id *match;
struct rk3x_i2c *i2c;
struct resource *mem;
int ret = 0;
int bus_nr;
u32 value;
int irq;
unsigned long clk_rate;
i2c = devm_kzalloc(&pdev->dev, sizeof(struct rk3x_i2c), GFP_KERNEL);
if (!i2c)
return -ENOMEM;
match = of_match_node(rk3x_i2c_match, np);
i2c->soc_data = (struct rk3x_i2c_soc_data *)match->data;
/* use common interface to get I2C timing properties */
i2c_parse_fw_timings(&pdev->dev, &i2c->t, true);
strlcpy(i2c->adap.name, "rk3x-i2c", sizeof(i2c->adap.name));
i2c->adap.owner = THIS_MODULE;
i2c->adap.algo = &rk3x_i2c_algorithm;
i2c->adap.retries = 3;
i2c->adap.dev.of_node = np;
i2c->adap.algo_data = i2c;
i2c->adap.dev.parent = &pdev->dev;
i2c->dev = &pdev->dev;
spin_lock_init(&i2c->lock);
init_waitqueue_head(&i2c->wait);
i2c->clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(i2c->clk)) {
dev_err(&pdev->dev, "cannot get clock\n");
return PTR_ERR(i2c->clk);
}
mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
i2c->regs = devm_ioremap_resource(&pdev->dev, mem);
if (IS_ERR(i2c->regs))
return PTR_ERR(i2c->regs);
/* Try to set the I2C adapter number from dt */
bus_nr = of_alias_get_id(np, "i2c");
/*
* Switch to new interface if the SoC also offers the old one.
* The control bit is located in the GRF register space.
*/
if (i2c->soc_data->grf_offset >= 0) {
struct regmap *grf;
grf = syscon_regmap_lookup_by_phandle(np, "rockchip,grf");
if (IS_ERR(grf)) {
dev_err(&pdev->dev,
"rk3x-i2c needs 'rockchip,grf' property\n");
return PTR_ERR(grf);
}
if (bus_nr < 0) {
dev_err(&pdev->dev, "rk3x-i2c needs i2cX alias");
return -EINVAL;
}
/* 27+i: write mask, 11+i: value */
value = BIT(27 + bus_nr) | BIT(11 + bus_nr);
ret = regmap_write(grf, i2c->soc_data->grf_offset, value);
if (ret != 0) {
dev_err(i2c->dev, "Could not write to GRF: %d\n", ret);
return ret;
}
}
/* IRQ setup */
irq = platform_get_irq(pdev, 0);
if (irq < 0) {
dev_err(&pdev->dev, "cannot find rk3x IRQ\n");
return irq;
}
ret = devm_request_irq(&pdev->dev, irq, rk3x_i2c_irq,
0, dev_name(&pdev->dev), i2c);
if (ret < 0) {
dev_err(&pdev->dev, "cannot request IRQ\n");
return ret;
}
platform_set_drvdata(pdev, i2c);
ret = clk_prepare(i2c->clk);
if (ret < 0) {
dev_err(&pdev->dev, "Could not prepare clock\n");
return ret;
}
i2c->clk_rate_nb.notifier_call = rk3x_i2c_clk_notifier_cb;
ret = clk_notifier_register(i2c->clk, &i2c->clk_rate_nb);
if (ret != 0) {
dev_err(&pdev->dev, "Unable to register clock notifier\n");
goto err_clk;
}
clk_rate = clk_get_rate(i2c->clk);
rk3x_i2c_adapt_div(i2c, clk_rate);
ret = i2c_add_adapter(&i2c->adap);
if (ret < 0) {
dev_err(&pdev->dev, "Could not register adapter\n");
goto err_clk_notifier;
}
dev_info(&pdev->dev, "Initialized RK3xxx I2C bus at %p\n", i2c->regs);
return 0;
err_clk_notifier:
clk_notifier_unregister(i2c->clk, &i2c->clk_rate_nb);
err_clk:
clk_unprepare(i2c->clk);
return ret;
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| max schwarz | max schwarz | 683 | 98.56% | 2 | 40.00% |
| david wu | david wu | 4 | 0.58% | 1 | 20.00% |
| addy ke | addy ke | 3 | 0.43% | 1 | 20.00% |
| douglas anderson | douglas anderson | 3 | 0.43% | 1 | 20.00% |
| Total | 693 | 100.00% | 5 | 100.00% |
static int rk3x_i2c_remove(struct platform_device *pdev)
{
struct rk3x_i2c *i2c = platform_get_drvdata(pdev);
i2c_del_adapter(&i2c->adap);
clk_notifier_unregister(i2c->clk, &i2c->clk_rate_nb);
clk_unprepare(i2c->clk);
return 0;
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| max schwarz | max schwarz | 51 | 100.00% | 2 | 100.00% |
| Total | 51 | 100.00% | 2 | 100.00% |
static struct platform_driver rk3x_i2c_driver = {
.probe = rk3x_i2c_probe,
.remove = rk3x_i2c_remove,
.driver = {
.name = "rk3x-i2c",
.of_match_table = rk3x_i2c_match,
},
};
module_platform_driver(rk3x_i2c_driver);
MODULE_DESCRIPTION("Rockchip RK3xxx I2C Bus driver");
MODULE_AUTHOR("Max Schwarz <max.schwarz@online.de>");
MODULE_LICENSE("GPL v2");
Overall Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| max schwarz | max schwarz | 3344 | 83.85% | 2 | 14.29% |
| addy ke | addy ke | 483 | 12.11% | 4 | 28.57% |
| douglas anderson | douglas anderson | 61 | 1.53% | 2 | 14.29% |
| david wu | david wu | 57 | 1.43% | 1 | 7.14% |
| yakir yang | yakir yang | 20 | 0.50% | 1 | 7.14% |
| alexandru m stan | alexandru m stan | 8 | 0.20% | 1 | 7.14% |
| luis de bethencourt | luis de bethencourt | 7 | 0.18% | 1 | 7.14% |
| dmitry torokhov | dmitry torokhov | 6 | 0.15% | 1 | 7.14% |
| dan carpenter | dan carpenter | 2 | 0.05% | 1 | 7.14% |
| Total | 3988 | 100.00% | 14 | 100.00% |
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.