cregit-Linux how code gets into the kernel

Release 4.7 drivers/iio/gyro/adxrs450.c

Directory: drivers/iio/gyro
/*
 * ADXRS450/ADXRS453 Digital Output Gyroscope Driver
 *
 * Copyright 2011 Analog Devices Inc.
 *
 * Licensed under the GPL-2.
 */

#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/delay.h>
#include <linux/mutex.h>
#include <linux/device.h>
#include <linux/kernel.h>
#include <linux/spi/spi.h>
#include <linux/slab.h>
#include <linux/sysfs.h>
#include <linux/list.h>
#include <linux/module.h>

#include <linux/iio/iio.h>
#include <linux/iio/sysfs.h>


#define ADXRS450_STARTUP_DELAY	50 
/* ms */

/* The MSB for the spi commands */

#define ADXRS450_SENSOR_DATA    (0x20 << 24)

#define ADXRS450_WRITE_DATA	(0x40 << 24)

#define ADXRS450_READ_DATA	(0x80 << 24)


#define ADXRS450_RATE1	0x00	
/* Rate Registers */

#define ADXRS450_TEMP1	0x02	
/* Temperature Registers */

#define ADXRS450_LOCST1	0x04	
/* Low CST Memory Registers */

#define ADXRS450_HICST1	0x06	
/* High CST Memory Registers */

#define ADXRS450_QUAD1	0x08	
/* Quad Memory Registers */

#define ADXRS450_FAULT1	0x0A	
/* Fault Registers */

#define ADXRS450_PID1	0x0C	
/* Part ID Register 1 */

#define ADXRS450_SNH	0x0E	
/* Serial Number Registers, 4 bytes */

#define ADXRS450_SNL	0x10

#define ADXRS450_DNC1	0x12	
/* Dynamic Null Correction Registers */
/* Check bits */

#define ADXRS450_P	0x01

#define ADXRS450_CHK	0x02

#define ADXRS450_CST	0x04

#define ADXRS450_PWR	0x08

#define ADXRS450_POR	0x10

#define ADXRS450_NVM	0x20

#define ADXRS450_Q	0x40

#define ADXRS450_PLL	0x80

#define ADXRS450_UV	0x100

#define ADXRS450_OV	0x200

#define ADXRS450_AMP	0x400

#define ADXRS450_FAIL	0x800


#define ADXRS450_WRERR_MASK	(0x7 << 29)


#define ADXRS450_MAX_RX 4

#define ADXRS450_MAX_TX 4


#define ADXRS450_GET_ST(a)	((a >> 26) & 0x3)

enum {
	
ID_ADXRS450,
	
ID_ADXRS453,
};

/**
 * struct adxrs450_state - device instance specific data
 * @us:                 actual spi_device
 * @buf_lock:           mutex to protect tx and rx
 * @tx:                 transmit buffer
 * @rx:                 receive buffer
 **/

struct adxrs450_state {
	
struct spi_device	*us;
	
struct mutex		buf_lock;
	
__be32			tx ____cacheline_aligned;
	
__be32			rx;

};

/**
 * adxrs450_spi_read_reg_16() - read 2 bytes from a register pair
 * @indio_dev: device associated with child of actual iio_dev
 * @reg_address: the address of the lower of the two registers, which should be
 *      an even address, the second register's address is reg_address + 1.
 * @val: somewhere to pass back the value read
 **/

static int adxrs450_spi_read_reg_16(struct iio_dev *indio_dev, u8 reg_address, u16 *val) { struct adxrs450_state *st = iio_priv(indio_dev); u32 tx; int ret; struct spi_transfer xfers[] = { { .tx_buf = &st->tx, .bits_per_word = 8, .len = sizeof(st->tx), .cs_change = 1, }, { .rx_buf = &st->rx, .bits_per_word = 8, .len = sizeof(st->rx), }, }; mutex_lock(&st->buf_lock); tx = ADXRS450_READ_DATA | (reg_address << 17); if (!(hweight32(tx) & 1)) tx |= ADXRS450_P; st->tx = cpu_to_be32(tx); ret = spi_sync_transfer(st->us, xfers, ARRAY_SIZE(xfers)); if (ret) { dev_err(&st->us->dev, "problem while reading 16 bit register 0x%02x\n", reg_address); goto error_ret; } *val = (be32_to_cpu(st->rx) >> 5) & 0xFFFF; error_ret: mutex_unlock(&st->buf_lock); return ret; }

Contributors

PersonTokensPropCommitsCommitProp
michael hennerichmichael hennerich12158.45%444.44%
lars-peter clausenlars-peter clausen8340.10%333.33%
jonathan cameronjonathan cameron31.45%222.22%
Total207100.00%9100.00%

/** * adxrs450_spi_write_reg_16() - write 2 bytes data to a register pair * @indio_dev: device associated with child of actual actual iio_dev * @reg_address: the address of the lower of the two registers,which should be * an even address, the second register's address is reg_address + 1. * @val: value to be written. **/
static int adxrs450_spi_write_reg_16(struct iio_dev *indio_dev, u8 reg_address, u16 val) { struct adxrs450_state *st = iio_priv(indio_dev); u32 tx; int ret; mutex_lock(&st->buf_lock); tx = ADXRS450_WRITE_DATA | (reg_address << 17) | (val << 1); if (!(hweight32(tx) & 1)) tx |= ADXRS450_P; st->tx = cpu_to_be32(tx); ret = spi_write(st->us, &st->tx, sizeof(st->tx)); if (ret) dev_err(&st->us->dev, "problem while writing 16 bit register 0x%02x\n", reg_address); usleep_range(100, 1000); /* enforce sequential transfer delay 0.1ms */ mutex_unlock(&st->buf_lock); return ret; }

Contributors

PersonTokensPropCommitsCommitProp
michael hennerichmichael hennerich10474.29%337.50%
lars-peter clausenlars-peter clausen2820.00%225.00%
jonathan cameronjonathan cameron85.71%337.50%
Total140100.00%8100.00%

/** * adxrs450_spi_sensor_data() - read 2 bytes sensor data * @indio_dev: device associated with child of actual iio_dev * @val: somewhere to pass back the value read **/
static int adxrs450_spi_sensor_data(struct iio_dev *indio_dev, s16 *val) { struct adxrs450_state *st = iio_priv(indio_dev); int ret; struct spi_transfer xfers[] = { { .tx_buf = &st->tx, .bits_per_word = 8, .len = sizeof(st->tx), .cs_change = 1, }, { .rx_buf = &st->rx, .bits_per_word = 8, .len = sizeof(st->rx), }, }; mutex_lock(&st->buf_lock); st->tx = cpu_to_be32(ADXRS450_SENSOR_DATA); ret = spi_sync_transfer(st->us, xfers, ARRAY_SIZE(xfers)); if (ret) { dev_err(&st->us->dev, "Problem while reading sensor data\n"); goto error_ret; } *val = (be32_to_cpu(st->rx) >> 10) & 0xFFFF; error_ret: mutex_unlock(&st->buf_lock); return ret; }

Contributors

PersonTokensPropCommitsCommitProp
michael hennerichmichael hennerich9856.65%337.50%
lars-peter clausenlars-peter clausen7241.62%337.50%
jonathan cameronjonathan cameron31.73%225.00%
Total173100.00%8100.00%

/** * adxrs450_spi_initial() - use for initializing procedure. * @st: device instance specific data * @val: somewhere to pass back the value read * @chk: Whether to perform fault check **/
static int adxrs450_spi_initial(struct adxrs450_state *st, u32 *val, char chk) { int ret; u32 tx; struct spi_transfer xfers = { .tx_buf = &st->tx, .rx_buf = &st->rx, .bits_per_word = 8, .len = sizeof(st->tx), }; mutex_lock(&st->buf_lock); tx = ADXRS450_SENSOR_DATA; if (chk) tx |= (ADXRS450_CHK | ADXRS450_P); st->tx = cpu_to_be32(tx); ret = spi_sync_transfer(st->us, &xfers, 1); if (ret) { dev_err(&st->us->dev, "Problem while reading initializing data\n"); goto error_ret; } *val = be32_to_cpu(st->rx); error_ret: mutex_unlock(&st->buf_lock); return ret; }

Contributors

PersonTokensPropCommitsCommitProp
michael hennerichmichael hennerich12884.21%133.33%
lars-peter clausenlars-peter clausen2415.79%266.67%
Total152100.00%3100.00%

/* Recommended Startup Sequence by spec */
static int adxrs450_initial_setup(struct iio_dev *indio_dev) { u32 t; u16 data; int ret; struct adxrs450_state *st = iio_priv(indio_dev); msleep(ADXRS450_STARTUP_DELAY*2); ret = adxrs450_spi_initial(st, &t, 1); if (ret) return ret; if (t != 0x01) dev_warn(&st->us->dev, "The initial power on response is not correct! Restart without reset?\n"); msleep(ADXRS450_STARTUP_DELAY); ret = adxrs450_spi_initial(st, &t, 0); if (ret) return ret; msleep(ADXRS450_STARTUP_DELAY); ret = adxrs450_spi_initial(st, &t, 0); if (ret) return ret; if (((t & 0xff) | 0x01) != 0xff || ADXRS450_GET_ST(t) != 2) { dev_err(&st->us->dev, "The second response is not correct!\n"); return -EIO; } ret = adxrs450_spi_initial(st, &t, 0); if (ret) return ret; if (((t & 0xff) | 0x01) != 0xff || ADXRS450_GET_ST(t) != 2) { dev_err(&st->us->dev, "The third response is not correct!\n"); return -EIO; } ret = adxrs450_spi_read_reg_16(indio_dev, ADXRS450_FAULT1, &data); if (ret) return ret; if (data & 0x0fff) { dev_err(&st->us->dev, "The device is not in normal status!\n"); return -EINVAL; } return 0; }

Contributors

PersonTokensPropCommitsCommitProp
michael hennerichmichael hennerich25295.09%240.00%
jonathan cameronjonathan cameron124.53%240.00%
lars-peter clausenlars-peter clausen10.38%120.00%
Total265100.00%5100.00%


static int adxrs450_write_raw(struct iio_dev *indio_dev, struct iio_chan_spec const *chan, int val, int val2, long mask) { int ret; switch (mask) { case IIO_CHAN_INFO_CALIBBIAS: if (val < -0x400 || val >= 0x400) return -EINVAL; ret = adxrs450_spi_write_reg_16(indio_dev, ADXRS450_DNC1, val); break; default: ret = -EINVAL; break; } return ret; }

Contributors

PersonTokensPropCommitsCommitProp
jonathan cameronjonathan cameron5472.00%250.00%
lars-peter clausenlars-peter clausen1520.00%125.00%
michael hennerichmichael hennerich68.00%125.00%
Total75100.00%4100.00%


static int adxrs450_read_raw(struct iio_dev *indio_dev, struct iio_chan_spec const *chan, int *val, int *val2, long mask) { int ret; s16 t; switch (mask) { case IIO_CHAN_INFO_RAW: switch (chan->type) { case IIO_ANGL_VEL: ret = adxrs450_spi_sensor_data(indio_dev, &t); if (ret) break; *val = t; ret = IIO_VAL_INT; break; case IIO_TEMP: ret = adxrs450_spi_read_reg_16(indio_dev, ADXRS450_TEMP1, &t); if (ret) break; *val = (t >> 6) + 225; ret = IIO_VAL_INT; break; default: ret = -EINVAL; break; } break; case IIO_CHAN_INFO_SCALE: switch (chan->type) { case IIO_ANGL_VEL: *val = 0; *val2 = 218166; return IIO_VAL_INT_PLUS_NANO; case IIO_TEMP: *val = 200; *val2 = 0; return IIO_VAL_INT; default: return -EINVAL; } case IIO_CHAN_INFO_QUADRATURE_CORRECTION_RAW: ret = adxrs450_spi_read_reg_16(indio_dev, ADXRS450_QUAD1, &t); if (ret) break; *val = t; ret = IIO_VAL_INT; break; case IIO_CHAN_INFO_CALIBBIAS: ret = adxrs450_spi_read_reg_16(indio_dev, ADXRS450_DNC1, &t); if (ret) break; *val = sign_extend32(t, 9); ret = IIO_VAL_INT; break; default: ret = -EINVAL; break; } return ret; }

Contributors

PersonTokensPropCommitsCommitProp
jonathan cameronjonathan cameron14257.72%555.56%
michael hennerichmichael hennerich9940.24%333.33%
lars-peter clausenlars-peter clausen52.03%111.11%
Total246100.00%9100.00%

static const struct iio_chan_spec adxrs450_channels[2][2] = { [ID_ADXRS450] = { { .type = IIO_ANGL_VEL, .modified = 1, .channel2 = IIO_MOD_Z, .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_CALIBBIAS) | BIT(IIO_CHAN_INFO_QUADRATURE_CORRECTION_RAW) | BIT(IIO_CHAN_INFO_SCALE), }, { .type = IIO_TEMP, .indexed = 1, .channel = 0, .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE), } }, [ID_ADXRS453] = { { .type = IIO_ANGL_VEL, .modified = 1, .channel2 = IIO_MOD_Z, .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE) | BIT(IIO_CHAN_INFO_QUADRATURE_CORRECTION_RAW), }, { .type = IIO_TEMP, .indexed = 1, .channel = 0, .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE), } }, }; static const struct iio_info adxrs450_info = { .driver_module = THIS_MODULE, .read_raw = &adxrs450_read_raw, .write_raw = &adxrs450_write_raw, };
static int adxrs450_probe(struct spi_device *spi) { int ret; struct adxrs450_state *st; struct iio_dev *indio_dev; /* setup the industrialio driver allocated elements */ indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st)); if (!indio_dev) return -ENOMEM; st = iio_priv(indio_dev); st->us = spi; mutex_init(&st->buf_lock); /* This is only used for removal purposes */ spi_set_drvdata(spi, indio_dev); indio_dev->dev.parent = &spi->dev; indio_dev->info = &adxrs450_info; indio_dev->modes = INDIO_DIRECT_MODE; indio_dev->channels = adxrs450_channels[spi_get_device_id(spi)->driver_data]; indio_dev->num_channels = ARRAY_SIZE(adxrs450_channels); indio_dev->name = spi->dev.driver->name; ret = devm_iio_device_register(&spi->dev, indio_dev); if (ret) return ret; /* Get the device into a sane initial state */ ret = adxrs450_initial_setup(indio_dev); if (ret) return ret; return 0; }

Contributors

PersonTokensPropCommitsCommitProp
michael hennerichmichael hennerich11163.43%225.00%
jonathan cameronjonathan cameron4626.29%450.00%
sachin kamatsachin kamat1810.29%225.00%
Total175100.00%8100.00%

static const struct spi_device_id adxrs450_id[] = { {"adxrs450", ID_ADXRS450}, {"adxrs453", ID_ADXRS453}, {} }; MODULE_DEVICE_TABLE(spi, adxrs450_id); static struct spi_driver adxrs450_driver = { .driver = { .name = "adxrs450", }, .probe = adxrs450_probe, .id_table = adxrs450_id, }; module_spi_driver(adxrs450_driver); MODULE_AUTHOR("Cliff Cai <cliff.cai@xxxxxxxxxx>"); MODULE_DESCRIPTION("Analog Devices ADXRS450/ADXRS453 Gyroscope SPI driver"); MODULE_LICENSE("GPL v2");

Overall Contributors

PersonTokensPropCommitsCommitProp
michael hennerichmichael hennerich110357.90%1028.57%
lars-peter clausenlars-peter clausen39720.84%1131.43%
jonathan cameronjonathan cameron38420.16%1131.43%
sachin kamatsachin kamat180.94%25.71%
paul gortmakerpaul gortmaker30.16%12.86%
Total1905100.00%35100.00%
Directory: drivers/iio/gyro
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.
{% endraw %}