cregit-Linux how code gets into the kernel

Release 4.7 drivers/input/touchscreen/bu21013_ts.c

Directory: drivers/input/touchscreen
/*
 * Copyright (C) ST-Ericsson SA 2010
 * Author: Naveen Kumar G <naveen.gaddipati@stericsson.com> for ST-Ericsson
 * License terms:GNU General Public License (GPL) version 2
 */

#include <linux/kernel.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/i2c.h>
#include <linux/workqueue.h>
#include <linux/input.h>
#include <linux/input/bu21013.h>
#include <linux/slab.h>
#include <linux/regulator/consumer.h>
#include <linux/module.h>
#include <linux/gpio.h>
#include <linux/of.h>
#include <linux/of_gpio.h>


#define PEN_DOWN_INTR	0

#define MAX_FINGERS	2

#define RESET_DELAY	30

#define PENUP_TIMEOUT	(10)

#define DELTA_MIN	16

#define MASK_BITS	0x03

#define SHIFT_8		8

#define SHIFT_2		2

#define LENGTH_OF_BUFFER	11

#define I2C_RETRY_COUNT	5


#define BU21013_SENSORS_BTN_0_7_REG	0x70

#define BU21013_SENSORS_BTN_8_15_REG	0x71

#define BU21013_SENSORS_BTN_16_23_REG	0x72

#define BU21013_X1_POS_MSB_REG		0x73

#define BU21013_X1_POS_LSB_REG		0x74

#define BU21013_Y1_POS_MSB_REG		0x75

#define BU21013_Y1_POS_LSB_REG		0x76

#define BU21013_X2_POS_MSB_REG		0x77

#define BU21013_X2_POS_LSB_REG		0x78

#define BU21013_Y2_POS_MSB_REG		0x79

#define BU21013_Y2_POS_LSB_REG		0x7A

#define BU21013_INT_CLR_REG		0xE8

#define BU21013_INT_MODE_REG		0xE9

#define BU21013_GAIN_REG		0xEA

#define BU21013_OFFSET_MODE_REG		0xEB

#define BU21013_XY_EDGE_REG		0xEC

#define BU21013_RESET_REG		0xED

#define BU21013_CALIB_REG		0xEE

#define BU21013_DONE_REG		0xEF

#define BU21013_SENSOR_0_7_REG		0xF0

#define BU21013_SENSOR_8_15_REG		0xF1

#define BU21013_SENSOR_16_23_REG	0xF2

#define BU21013_POS_MODE1_REG		0xF3

#define BU21013_POS_MODE2_REG		0xF4

#define BU21013_CLK_MODE_REG		0xF5

#define BU21013_IDLE_REG		0xFA

#define BU21013_FILTER_REG		0xFB

#define BU21013_TH_ON_REG		0xFC

#define BU21013_TH_OFF_REG		0xFD



#define BU21013_RESET_ENABLE		0x01


#define BU21013_SENSORS_EN_0_7		0x3F

#define BU21013_SENSORS_EN_8_15		0xFC

#define BU21013_SENSORS_EN_16_23	0x1F


#define BU21013_POS_MODE1_0		0x02

#define BU21013_POS_MODE1_1		0x04

#define BU21013_POS_MODE1_2		0x08


#define BU21013_POS_MODE2_ZERO		0x01

#define BU21013_POS_MODE2_AVG1		0x02

#define BU21013_POS_MODE2_AVG2		0x04

#define BU21013_POS_MODE2_EN_XY		0x08

#define BU21013_POS_MODE2_EN_RAW	0x10

#define BU21013_POS_MODE2_MULTI		0x80


#define BU21013_CLK_MODE_DIV		0x01

#define BU21013_CLK_MODE_EXT		0x02

#define BU21013_CLK_MODE_CALIB		0x80


#define BU21013_IDLET_0			0x01

#define BU21013_IDLET_1			0x02

#define BU21013_IDLET_2			0x04

#define BU21013_IDLET_3			0x08

#define BU21013_IDLE_INTERMIT_EN	0x10


#define BU21013_DELTA_0_6	0x7F

#define BU21013_FILTER_EN	0x80


#define BU21013_INT_MODE_LEVEL	0x00

#define BU21013_INT_MODE_EDGE	0x01


#define BU21013_GAIN_0		0x01

#define BU21013_GAIN_1		0x02

#define BU21013_GAIN_2		0x04


#define BU21013_OFFSET_MODE_DEFAULT	0x00

#define BU21013_OFFSET_MODE_MOVE	0x01

#define BU21013_OFFSET_MODE_DISABLE	0x02


#define BU21013_TH_ON_0		0x01

#define BU21013_TH_ON_1		0x02

#define BU21013_TH_ON_2		0x04

#define BU21013_TH_ON_3		0x08

#define BU21013_TH_ON_4		0x10

#define BU21013_TH_ON_5		0x20

#define BU21013_TH_ON_6		0x40

#define BU21013_TH_ON_7		0x80

#define BU21013_TH_ON_MAX	0xFF


#define BU21013_TH_OFF_0	0x01

#define BU21013_TH_OFF_1	0x02

#define BU21013_TH_OFF_2	0x04

#define BU21013_TH_OFF_3	0x08

#define BU21013_TH_OFF_4	0x10

#define BU21013_TH_OFF_5	0x20

#define BU21013_TH_OFF_6	0x40

#define BU21013_TH_OFF_7	0x80

#define BU21013_TH_OFF_MAX	0xFF


#define BU21013_X_EDGE_0	0x01

#define BU21013_X_EDGE_1	0x02

#define BU21013_X_EDGE_2	0x04

#define BU21013_X_EDGE_3	0x08

#define BU21013_Y_EDGE_0	0x10

#define BU21013_Y_EDGE_1	0x20

#define BU21013_Y_EDGE_2	0x40

#define BU21013_Y_EDGE_3	0x80


#define BU21013_DONE	0x01

#define BU21013_NUMBER_OF_X_SENSORS	(6)

#define BU21013_NUMBER_OF_Y_SENSORS	(11)


#define DRIVER_TP	"bu21013_tp"

/**
 * struct bu21013_ts_data - touch panel data structure
 * @client: pointer to the i2c client
 * @wait: variable to wait_queue_head_t structure
 * @touch_stopped: touch stop flag
 * @chip: pointer to the touch panel controller
 * @in_dev: pointer to the input device structure
 * @intr_pin: interrupt pin value
 * @regulator: pointer to the Regulator used for touch screen
 *
 * Touch panel device data structure
 */

struct bu21013_ts_data {
	
struct i2c_client *client;
	
wait_queue_head_t wait;
	
const struct bu21013_platform_device *chip;
	
struct input_dev *in_dev;
	
struct regulator *regulator;
	
unsigned int irq;
	
unsigned int intr_pin;
	
bool touch_stopped;
};

/**
 * bu21013_read_block_data(): read the touch co-ordinates
 * @data: bu21013_ts_data structure pointer
 * @buf: byte pointer
 *
 * Read the touch co-ordinates using i2c read block into buffer
 * and returns integer.
 */



static int bu21013_read_block_data(struct bu21013_ts_data *data, u8 *buf)
{
	int ret, i;

	for (i = 0; i < I2C_RETRY_COUNT; i++) {
		ret = i2c_smbus_read_i2c_block_data
			(data->client, BU21013_SENSORS_BTN_0_7_REG,
				LENGTH_OF_BUFFER, buf);
		if (ret == LENGTH_OF_BUFFER)
			return 0;
	}
	return -EINVAL;
}


Contributors
PersonTokensPropCommitsCommitProp
naveen kumar gaddipatinaveen kumar gaddipati63100.00%1100.00%


Total63100.00%1100.00%



/**
 * bu21013_do_touch_report(): Get the touch co-ordinates
 * @data: bu21013_ts_data structure pointer
 *
 * Get the touch co-ordinates from touch sensor registers and writes
 * into device structure and returns integer.
 */



static int bu21013_do_touch_report(struct bu21013_ts_data *data)
{
	u8	buf[LENGTH_OF_BUFFER];
	unsigned int pos_x[2], pos_y[2];
	bool	has_x_sensors, has_y_sensors;
	int	finger_down_count = 0;
	int	i;

	if (data == NULL)
		return -EINVAL;

	if (bu21013_read_block_data(data, buf) < 0)
		return -EINVAL;

	has_x_sensors = hweight32(buf[0] & BU21013_SENSORS_EN_0_7);
	has_y_sensors = hweight32(((buf[1] & BU21013_SENSORS_EN_8_15) |
		((buf[2] & BU21013_SENSORS_EN_16_23) << SHIFT_8)) >> SHIFT_2);
	if (!has_x_sensors || !has_y_sensors)
		return 0;

	for (i = 0; i < MAX_FINGERS; i++) {
		const u8 *p = &buf[4 * i + 3];
		unsigned int x = p[0] << SHIFT_2 | (p[1] & MASK_BITS);
		unsigned int y = p[2] << SHIFT_2 | (p[3] & MASK_BITS);
		if (x == 0 || y == 0)
			continue;
		pos_x[finger_down_count] = x;
		pos_y[finger_down_count] = y;
		finger_down_count++;
	}

	if (finger_down_count) {
		if (finger_down_count == 2 &&
		    (abs(pos_x[0] - pos_x[1]) < DELTA_MIN ||
		     abs(pos_y[0] - pos_y[1]) < DELTA_MIN)) {
			return 0;
		}

		for (i = 0; i < finger_down_count; i++) {
			if (data->chip->x_flip)
				pos_x[i] = data->chip->touch_x_max - pos_x[i];
			if (data->chip->y_flip)
				pos_y[i] = data->chip->touch_y_max - pos_y[i];

			input_report_abs(data->in_dev,
					 ABS_MT_POSITION_X, pos_x[i]);
			input_report_abs(data->in_dev,
					 ABS_MT_POSITION_Y, pos_y[i]);
			input_mt_sync(data->in_dev);
		}
	} else
		input_mt_sync(data->in_dev);

	input_sync(data->in_dev);

	return 0;
}

Contributors
PersonTokensPropCommitsCommitProp
naveen kumar gaddipatinaveen kumar gaddipati384100.00%1100.00%


Total384100.00%1100.00%



/**
 * bu21013_gpio_irq() - gpio thread function for touch interrupt
 * @irq: irq value
 * @device_data: void pointer
 *
 * This gpio thread function for touch interrupt
 * and returns irqreturn_t.
 */



static irqreturn_t bu21013_gpio_irq(int irq, void *device_data)
{
	struct bu21013_ts_data *data = device_data;
	struct i2c_client *i2c = data->client;
	int retval;

	do {
		retval = bu21013_do_touch_report(data);
		if (retval < 0) {
			dev_err(&i2c->dev, "bu21013_do_touch_report failed\n");
			return IRQ_NONE;
		}

		data->intr_pin = gpio_get_value(data->chip->touch_pin);
		if (data->intr_pin == PEN_DOWN_INTR)
			wait_event_timeout(data->wait, data->touch_stopped,
					   msecs_to_jiffies(2));
	} while (!data->intr_pin && !data->touch_stopped);

	return IRQ_HANDLED;
}


Contributors
PersonTokensPropCommitsCommitProp
naveen kumar gaddipatinaveen kumar gaddipati11296.55%150.00%


lee joneslee jones43.45%150.00%


Total116100.00%2100.00%



/**
 * bu21013_init_chip() - power on sequence for the bu21013 controller
 * @data: device structure pointer
 *
 * This function is used to power on
 * the bu21013 controller and returns integer.
 */



static int bu21013_init_chip(struct bu21013_ts_data *data)
{
	int retval;
	struct i2c_client *i2c = data->client;

	retval = i2c_smbus_write_byte_data(i2c, BU21013_RESET_REG,
					BU21013_RESET_ENABLE);
	if (retval < 0) {
		dev_err(&i2c->dev, "BU21013_RESET reg write failed\n");
		return retval;
	}
	msleep(RESET_DELAY);

	retval = i2c_smbus_write_byte_data(i2c, BU21013_SENSOR_0_7_REG,
					BU21013_SENSORS_EN_0_7);
	if (retval < 0) {
		dev_err(&i2c->dev, "BU21013_SENSOR_0_7 reg write failed\n");
		return retval;
	}

	retval = i2c_smbus_write_byte_data(i2c, BU21013_SENSOR_8_15_REG,
						BU21013_SENSORS_EN_8_15);
	if (retval < 0) {
		dev_err(&i2c->dev, "BU21013_SENSOR_8_15 reg write failed\n");
		return retval;
	}

	retval = i2c_smbus_write_byte_data(i2c, BU21013_SENSOR_16_23_REG,
						BU21013_SENSORS_EN_16_23);
	if (retval < 0) {
		dev_err(&i2c->dev, "BU21013_SENSOR_16_23 reg write failed\n");
		return retval;
	}

	retval = i2c_smbus_write_byte_data(i2c, BU21013_POS_MODE1_REG,
				(BU21013_POS_MODE1_0 | BU21013_POS_MODE1_1));
	if (retval < 0) {
		dev_err(&i2c->dev, "BU21013_POS_MODE1 reg write failed\n");
		return retval;
	}

	retval = i2c_smbus_write_byte_data(i2c, BU21013_POS_MODE2_REG,
			(BU21013_POS_MODE2_ZERO | BU21013_POS_MODE2_AVG1 |
			BU21013_POS_MODE2_AVG2 | BU21013_POS_MODE2_EN_RAW |
			BU21013_POS_MODE2_MULTI));
	if (retval < 0) {
		dev_err(&i2c->dev, "BU21013_POS_MODE2 reg write failed\n");
		return retval;
	}

	if (data->chip->ext_clk)
		retval = i2c_smbus_write_byte_data(i2c, BU21013_CLK_MODE_REG,
			(BU21013_CLK_MODE_EXT | BU21013_CLK_MODE_CALIB));
	else
		retval = i2c_smbus_write_byte_data(i2c, BU21013_CLK_MODE_REG,
			(BU21013_CLK_MODE_DIV | BU21013_CLK_MODE_CALIB));
	if (retval < 0) {
		dev_err(&i2c->dev, "BU21013_CLK_MODE reg write failed\n");
		return retval;
	}

	retval = i2c_smbus_write_byte_data(i2c, BU21013_IDLE_REG,
				(BU21013_IDLET_0 | BU21013_IDLE_INTERMIT_EN));
	if (retval < 0) {
		dev_err(&i2c->dev, "BU21013_IDLE reg write failed\n");
		return retval;
	}

	retval = i2c_smbus_write_byte_data(i2c, BU21013_INT_MODE_REG,
						BU21013_INT_MODE_LEVEL);
	if (retval < 0) {
		dev_err(&i2c->dev, "BU21013_INT_MODE reg write failed\n");
		return retval;
	}

	retval = i2c_smbus_write_byte_data(i2c, BU21013_FILTER_REG,
						(BU21013_DELTA_0_6 |
							BU21013_FILTER_EN));
	if (retval < 0) {
		dev_err(&i2c->dev, "BU21013_FILTER reg write failed\n");
		return retval;
	}

	retval = i2c_smbus_write_byte_data(i2c, BU21013_TH_ON_REG,
					BU21013_TH_ON_5);
	if (retval < 0) {
		dev_err(&i2c->dev, "BU21013_TH_ON reg write failed\n");
		return retval;
	}

	retval = i2c_smbus_write_byte_data(i2c, BU21013_TH_OFF_REG,
				BU21013_TH_OFF_4 | BU21013_TH_OFF_3);
	if (retval < 0) {
		dev_err(&i2c->dev, "BU21013_TH_OFF reg write failed\n");
		return retval;
	}

	retval = i2c_smbus_write_byte_data(i2c, BU21013_GAIN_REG,
					(BU21013_GAIN_0 | BU21013_GAIN_1));
	if (retval < 0) {
		dev_err(&i2c->dev, "BU21013_GAIN reg write failed\n");
		return retval;
	}

	retval = i2c_smbus_write_byte_data(i2c, BU21013_OFFSET_MODE_REG,
					BU21013_OFFSET_MODE_DEFAULT);
	if (retval < 0) {
		dev_err(&i2c->dev, "BU21013_OFFSET_MODE reg write failed\n");
		return retval;
	}

	retval = i2c_smbus_write_byte_data(i2c, BU21013_XY_EDGE_REG,
				(BU21013_X_EDGE_0 | BU21013_X_EDGE_2 |
				BU21013_Y_EDGE_1 | BU21013_Y_EDGE_3));
	if (retval < 0) {
		dev_err(&i2c->dev, "BU21013_XY_EDGE reg write failed\n");
		return retval;
	}

	retval = i2c_smbus_write_byte_data(i2c, BU21013_DONE_REG,
							BU21013_DONE);
	if (retval < 0) {
		dev_err(&i2c->dev, "BU21013_REG_DONE reg write failed\n");
		return retval;
	}

	return 0;
}


Contributors
PersonTokensPropCommitsCommitProp
naveen kumar gaddipatinaveen kumar gaddipati60699.84%150.00%


david sterbadavid sterba10.16%150.00%


Total607100.00%2100.00%



/**
 * bu21013_free_irq() - frees IRQ registered for touchscreen
 * @bu21013_data: device structure pointer
 *
 * This function signals interrupt thread to stop processing and
 * frees interrupt.
 */



static void bu21013_free_irq(struct bu21013_ts_data *bu21013_data)
{
	bu21013_data->touch_stopped = true;
	wake_up(&bu21013_data->wait);
	free_irq(bu21013_data->irq, bu21013_data);
}


Contributors
PersonTokensPropCommitsCommitProp
naveen kumar gaddipatinaveen kumar gaddipati2882.35%150.00%


lee joneslee jones617.65%150.00%


Total34100.00%2100.00%



/**
 * bu21013_cs_disable() - deconfigures the touch panel controller
 * @bu21013_data: device structure pointer
 *
 * This function is used to deconfigure the chip selection
 * for touch panel controller.
 */



static void bu21013_cs_disable(struct bu21013_ts_data *bu21013_data)
{
	int error;

	error = gpio_direction_output(bu21013_data->chip->cs_pin, 0);
	if (error < 0)
		dev_warn(&bu21013_data->client->dev,
			 "%s: gpio direction failed, error: %d\n",
			 __func__, error);
	else
		gpio_set_value(bu21013_data->chip->cs_pin, 0);

	gpio_free(bu21013_data->chip->cs_pin);
}


Contributors
PersonTokensPropCommitsCommitProp
lee joneslee jones6390.00%150.00%


naveen kumar gaddipatinaveen kumar gaddipati710.00%150.00%


Total70100.00%2100.00%



#ifdef CONFIG_OF


static const struct bu21013_platform_device *

bu21013_parse_dt(struct device *dev)
{
	struct device_node *np = dev->of_node;
	struct bu21013_platform_device *pdata;

	if (!np) {
		dev_err(dev, "no device tree or platform data\n");
		return ERR_PTR(-EINVAL);
	}

	pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
	if (!pdata)
		return ERR_PTR(-ENOMEM);

	pdata->y_flip = pdata->x_flip = false;

	pdata->x_flip = of_property_read_bool(np, "rohm,flip-x");
	pdata->y_flip = of_property_read_bool(np, "rohm,flip-y");

	of_property_read_u32(np, "rohm,touch-max-x", &pdata->touch_x_max);
	of_property_read_u32(np, "rohm,touch-max-y", &pdata->touch_y_max);

	pdata->touch_pin = of_get_named_gpio(np, "touch-gpio", 0);
	pdata->cs_pin = of_get_named_gpio(np, "reset-gpio", 0);

	pdata->ext_clk = false;

	return pdata;
}

Contributors
PersonTokensPropCommitsCommitProp
lee joneslee jones167100.00%1100.00%


Total167100.00%1100.00%



#else


static inline const struct bu21013_platform_device *

bu21013_parse_dt(struct device *dev)
{
	dev_err(dev, "no platform data available\n");
	return ERR_PTR(-EINVAL);
}

Contributors
PersonTokensPropCommitsCommitProp
lee joneslee jones29100.00%1100.00%


Total29100.00%1100.00%



#endif

/**
 * bu21013_probe() - initializes the i2c-client touchscreen driver
 * @client: i2c client structure pointer
 * @id: i2c device id pointer
 *
 * This function used to initializes the i2c-client touchscreen
 * driver and returns integer.
 */



static int bu21013_probe(struct i2c_client *client,
			 const struct i2c_device_id *id)
{
	const struct bu21013_platform_device *pdata =
					dev_get_platdata(&client->dev);
	struct bu21013_ts_data *bu21013_data;
	struct input_dev *in_dev;
	int error;

	if (!i2c_check_functionality(client->adapter,
					I2C_FUNC_SMBUS_BYTE_DATA)) {
		dev_err(&client->dev, "i2c smbus byte data not supported\n");
		return -EIO;
	}

	if (!pdata) {
		pdata = bu21013_parse_dt(&client->dev);
		if (IS_ERR(pdata))
			return PTR_ERR(pdata);
	}

	if (!gpio_is_valid(pdata->touch_pin)) {
		dev_err(&client->dev, "invalid touch_pin supplied\n");
		return -EINVAL;
	}

	bu21013_data = kzalloc(sizeof(struct bu21013_ts_data), GFP_KERNEL);
	in_dev = input_allocate_device();
	if (!bu21013_data || !in_dev) {
		dev_err(&client->dev, "device memory alloc failed\n");
		error = -ENOMEM;
		goto err_free_mem;
	}

	bu21013_data->in_dev = in_dev;
	bu21013_data->chip = pdata;
	bu21013_data->client = client;
	bu21013_data->irq = gpio_to_irq(pdata->touch_pin);

	bu21013_data->regulator = regulator_get(&client->dev, "avdd");
	if (IS_ERR(bu21013_data->regulator)) {
		dev_err(&client->dev, "regulator_get failed\n");
		error = PTR_ERR(bu21013_data->regulator);
		goto err_free_mem;
	}

	error = regulator_enable(bu21013_data->regulator);
	if (error < 0) {
		dev_err(&client->dev, "regulator enable failed\n");
		goto err_put_regulator;
	}

	bu21013_data->touch_stopped = false;
	init_waitqueue_head(&bu21013_data->wait);

	/* configure the gpio pins */
	error = gpio_request_one(pdata->cs_pin, GPIOF_OUT_INIT_HIGH,
				 "touchp_reset");
	if (error < 0) {
		dev_err(&client->dev, "Unable to request gpio reset_pin\n");
		goto err_disable_regulator;
	}

	/* configure the touch panel controller */
	error = bu21013_init_chip(bu21013_data);
	if (error) {
		dev_err(&client->dev, "error in bu21013 config\n");
		goto err_cs_disable;
	}

	/* register the device to input subsystem */
	in_dev->name = DRIVER_TP;
	in_dev->id.bustype = BUS_I2C;
	in_dev->dev.parent = &client->dev;

	__set_bit(EV_SYN, in_dev->evbit);
	__set_bit(EV_KEY, in_dev->evbit);
	__set_bit(EV_ABS, in_dev->evbit);

	input_set_abs_params(in_dev, ABS_MT_POSITION_X, 0,
						pdata->touch_x_max, 0, 0);
	input_set_abs_params(in_dev, ABS_MT_POSITION_Y, 0,
						pdata->touch_y_max, 0, 0);
	input_set_drvdata(in_dev, bu21013_data);

	error = request_threaded_irq(bu21013_data->irq, NULL, bu21013_gpio_irq,
				     IRQF_TRIGGER_FALLING | IRQF_SHARED |
					IRQF_ONESHOT,
				     DRIVER_TP, bu21013_data);
	if (error) {
		dev_err(&client->dev, "request irq %d failed\n",
			bu21013_data->irq);
		goto err_cs_disable;
	}

	error = input_register_device(in_dev);
	if (error) {
		dev_err(&client->dev, "failed to register input device\n");
		goto err_free_irq;
	}

	device_init_wakeup(&client->dev, pdata->wakeup);
	i2c_set_clientdata(client, bu21013_data);

	return 0;

err_free_irq:
	bu21013_free_irq(bu21013_data);
err_cs_disable:
	bu21013_cs_disable(bu21013_data);
err_disable_regulator:
	regulator_disable(bu21013_data->regulator);
err_put_regulator:
	regulator_put(bu21013_data->regulator);
err_free_mem:
	input_free_device(in_dev);
	kfree(bu21013_data);

	return error;
}

Contributors
PersonTokensPropCommitsCommitProp
naveen kumar gaddipatinaveen kumar gaddipati51386.80%342.86%


lee joneslee jones7612.86%342.86%


lars-peter clausenlars-peter clausen20.34%114.29%


Total591100.00%7100.00%



/**
 * bu21013_remove() - removes the i2c-client touchscreen driver
 * @client: i2c client structure pointer
 *
 * This function uses to remove the i2c-client
 * touchscreen driver and returns integer.
 */



static int bu21013_remove(struct i2c_client *client)
{
	struct bu21013_ts_data *bu21013_data = i2c_get_clientdata(client);

	bu21013_free_irq(bu21013_data);

	bu21013_cs_disable(bu21013_data);

	input_unregister_device(bu21013_data->in_dev);

	regulator_disable(bu21013_data->regulator);
	regulator_put(bu21013_data->regulator);

	kfree(bu21013_data);

	device_init_wakeup(&client->dev, false);

	return 0;
}


Contributors
PersonTokensPropCommitsCommitProp
naveen kumar gaddipatinaveen kumar gaddipati6998.57%266.67%


lee joneslee jones11.43%133.33%


Total70100.00%3100.00%



#ifdef CONFIG_PM
/**
 * bu21013_suspend() - suspend the touch screen controller
 * @dev: pointer to device structure
 *
 * This function is used to suspend the
 * touch panel controller and returns integer
 */



static int bu21013_suspend(struct device *dev)
{
	struct bu21013_ts_data *bu21013_data = dev_get_drvdata(dev);
	struct i2c_client *client = bu21013_data->client;

	bu21013_data->touch_stopped = true;
	if (device_may_wakeup(&client->dev))
		enable_irq_wake(bu21013_data->irq);
	else
		disable_irq(bu21013_data->irq);

	regulator_disable(bu21013_data->regulator);

	return 0;
}


Contributors
PersonTokensPropCommitsCommitProp
naveen kumar gaddipatinaveen kumar gaddipati71100.00%2100.00%


Total71100.00%2100.00%



/**
 * bu21013_resume() - resume the touch screen controller
 * @dev: pointer to device structure
 *
 * This function is used to resume the touch panel
 * controller and returns integer.
 */



static int bu21013_resume(struct device *dev)
{
	struct bu21013_ts_data *bu21013_data = dev_get_drvdata(dev);
	struct i2c_client *client = bu21013_data->client;
	int retval;

	retval = regulator_enable(bu21013_data->regulator);
	if (retval < 0) {
		dev_err(&client->dev, "bu21013 regulator enable failed\n");
		return retval;
	}

	retval = bu21013_init_chip(bu21013_data);
	if (retval < 0) {
		dev_err(&client->dev, "bu21013 controller config failed\n");
		return retval;
	}

	bu21013_data->touch_stopped = false;

	if (device_may_wakeup(&client->dev))
		disable_irq_wake(bu21013_data->irq);
	else
		enable_irq(bu21013_data->irq);

	return 0;
}


Contributors
PersonTokensPropCommitsCommitProp
naveen kumar gaddipatinaveen kumar gaddipati125100.00%2100.00%


Total125100.00%2100.00%




static const struct dev_pm_ops bu21013_dev_pm_ops = {
	.suspend = bu21013_suspend,
	.resume  = bu21013_resume,
};
#endif


static const struct i2c_device_id bu21013_id[] = {
	{ DRIVER_TP, 0 },
	{ }
};
MODULE_DEVICE_TABLE(i2c, bu21013_id);


static struct i2c_driver bu21013_driver = {
	.driver	= {
		.name	=	DRIVER_TP,
#ifdef CONFIG_PM
		.pm	=	&bu21013_dev_pm_ops,
#endif
	},
	.probe		=	bu21013_probe,
	.remove		=	bu21013_remove,
	.id_table	=	bu21013_id,
};


module_i2c_driver(bu21013_driver);

MODULE_LICENSE("GPL v2");
MODULE_AUTHOR("Naveen Kumar G <naveen.gaddipati@stericsson.com>");
MODULE_DESCRIPTION("bu21013 touch screen controller driver");

Overall Contributors
PersonTokensPropCommitsCommitProp
naveen kumar gaddipatinaveen kumar gaddipati255486.99%330.00%


lee joneslee jones37412.74%330.00%


paul gortmakerpaul gortmaker30.10%110.00%


lars-peter clausenlars-peter clausen20.07%110.00%


axel linaxel lin20.07%110.00%


david sterbadavid sterba10.03%110.00%


Total2936100.00%10100.00%

  
Directory: drivers/input/touchscreen



Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.
{% endraw %}