/* * Copyright (C) 2014 Oleksij Rempel <linux@rempel-privat.de> * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. */ #ifndef _ALPHASCALE_ASM9260_ICOLL_H #define _ALPHASCALE_ASM9260_ICOLL_H #define ASM9260_NUM_IRQS 64 /* * this device provide 4 offsets for each register: * 0x0 - plain read write mode * 0x4 - set mode, OR logic. * 0x8 - clr mode, XOR logic. * 0xc - togle mode. */ #define ASM9260_HW_ICOLL_VECTOR 0x0000 /* * bits 31:2 * This register presents the vector address for the interrupt currently * active on the CPU IRQ input. Writing to this register notifies the * interrupt collector that the interrupt service routine for the current * interrupt has been entered. * The exception trap should have a LDPC instruction from this address: * LDPC ASM9260_HW_ICOLL_VECTOR_ADDR; IRQ exception at 0xffff0018 */ /* * The Interrupt Collector Level Acknowledge Register is used by software to * indicate the completion of an interrupt on a specific level. * This register is written at the very end of an interrupt service routine. If * nesting is used then the CPU irq must be turned on before writing to this * register to avoid a race condition in the CPU interrupt hardware. */ #define ASM9260_HW_ICOLL_LEVELACK 0x0010 #define ASM9260_BM_LEVELn(nr) BIT(nr) #define ASM9260_HW_ICOLL_CTRL 0x0020 /* * ASM9260_BM_CTRL_SFTRST and ASM9260_BM_CTRL_CLKGATE are not available on * asm9260. */ #define ASM9260_BM_CTRL_SFTRST BIT(31) #define ASM9260_BM_CTRL_CLKGATE BIT(30) /* disable interrupt level nesting */ #define ASM9260_BM_CTRL_NO_NESTING BIT(19) /* * Set this bit to one enable the RISC32-style read side effect associated with * the vector address register. In this mode, interrupt in-service is signaled * by the read of the ASM9260_HW_ICOLL_VECTOR register to acquire the interrupt * vector address. Set this bit to zero for normal operation, in which the ISR * signals in-service explicitly by means of a write to the * ASM9260_HW_ICOLL_VECTOR register. * 0 - Must Write to Vector register to go in-service. * 1 - Go in-service as a read side effect */ #define ASM9260_BM_CTRL_ARM_RSE_MODE BIT(18) #define ASM9260_BM_CTRL_IRQ_ENABLE BIT(16) #define ASM9260_HW_ICOLL_STAT_OFFSET 0x0030 /* * bits 5:0 * Vector number of current interrupt. Multiply by 4 and add to vector base * address to obtain the value in ASM9260_HW_ICOLL_VECTOR. */ /* * RAW0 and RAW1 provides a read-only view of the raw interrupt request lines * coming from various parts of the chip. Its purpose is to improve diagnostic * observability. */ #define ASM9260_HW_ICOLL_RAW0 0x0040 #define ASM9260_HW_ICOLL_RAW1 0x0050 #define ASM9260_HW_ICOLL_INTERRUPT0 0x0060 #define ASM9260_HW_ICOLL_INTERRUPTn(n) (0x0060 + ((n) >> 2) * 0x10) /* * WARNING: Modifying the priority of an enabled interrupt may result in * undefined behavior. */ #define ASM9260_BM_INT_PRIORITY_MASK 0x3 #define ASM9260_BM_INT_ENABLE BIT(2) #define ASM9260_BM_INT_SOFTIRQ BIT(3) #define ASM9260_BM_ICOLL_INTERRUPTn_SHIFT(n) (((n) & 0x3) << 3) #define ASM9260_BM_ICOLL_INTERRUPTn_ENABLE(n) (1 << (2 + \ ASM9260_BM_ICOLL_INTERRUPTn_SHIFT(n))) #define ASM9260_HW_ICOLL_VBASE 0x0160 /* * bits 31:2 * This bitfield holds the upper 30 bits of the base address of the vector * table. */ #define ASM9260_HW_ICOLL_CLEAR0 0x01d0 #define ASM9260_HW_ICOLL_CLEAR1 0x01e0 #define ASM9260_HW_ICOLL_CLEARn(n) (((n >> 5) * 0x10) \ + SET_REG) #define ASM9260_BM_CLEAR_BIT(n) BIT(n & 0x1f) /* Scratchpad */ #define ASM9260_HW_ICOLL_UNDEF_VECTOR 0x01f0 #endifOverall Contributors
| Person | Tokens | Prop | Commits | CommitProp | |
| oleksij rempel | oleksij rempel | 142 | 100.00% | 1 | 100.00% |
| Total | 142 | 100.00% | 1 | 100.00% |