Release 4.7 drivers/media/common/saa7146/saa7146_i2c.c

#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt

#include <media/drv-intf/saa7146_vv.h>



static u32 saa7146_i2c_func(struct i2c_adapter *adapter)
{
	/* DEB_I2C("'%s'\n", adapter->name); */

	return	  I2C_FUNC_I2C
		| I2C_FUNC_SMBUS_QUICK
		| I2C_FUNC_SMBUS_READ_BYTE	| I2C_FUNC_SMBUS_WRITE_BYTE
		| I2C_FUNC_SMBUS_READ_BYTE_DATA | I2C_FUNC_SMBUS_WRITE_BYTE_DATA;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
alan cox
alan cox
23
92.00%
1
33.33%
joe perches
joe perches
1
4.00%
1
33.33%
michael hunold
michael hunold
1
4.00%
1
33.33%
Total
25
100.00%
3
100.00%

/* this function returns the status-register of our i2c-device */


static inline u32 saa7146_i2c_status(struct saa7146_dev *dev)
{
	u32 iicsta = saa7146_read(dev, I2C_STATUS);
	/* DEB_I2C("status: 0x%08x\n", iicsta); */
	return iicsta;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
alan cox
alan cox
25
96.15%
1
50.00%
joe perches
joe perches
1
3.85%
1
50.00%
Total
26
100.00%
2
100.00%

/* this function runs through the i2c-messages and prepares the data to be
   sent through the saa7146. have a look at the specifications p. 122 ff
   to understand this. it returns the number of u32s to send, or -1
   in case of an error. */


static int saa7146_i2c_msg_prepare(const struct i2c_msg *m, int num, __le32 *op)
{
	int h1, h2;
	int i, j, addr;
	int mem = 0, op_count = 0;

	/* first determine size of needed memory */
	for(i = 0; i < num; i++) {
		mem += m[i].len + 1;
	}

	/* worst case: we need one u32 for three bytes to be send
           plus one extra byte to address the device */
	mem = 1 + ((mem-1) / 3);

	/* we assume that op points to a memory of at least
         * SAA7146_I2C_MEM bytes size. if we exceed this limit...
         */
	if ((4 * mem) > SAA7146_I2C_MEM) {
		/* DEB_I2C("cannot prepare i2c-message\n"); */
		return -ENOMEM;
	}

	/* be careful: clear out the i2c-mem first */
	memset(op,0,sizeof(__le32)*mem);

	/* loop through all messages */
	for(i = 0; i < num; i++) {

		/* insert the address of the i2c-slave.
                   note: we get 7 bit i2c-addresses,
                   so we have to perform a translation */
		addr = (m[i].addr*2) + ( (0 != (m[i].flags & I2C_M_RD)) ? 1 : 0);
		h1 = op_count/3; h2 = op_count%3;
		op[h1] |= cpu_to_le32(	    (u8)addr << ((3-h2)*8));
		op[h1] |= cpu_to_le32(SAA7146_I2C_START << ((3-h2)*2));
		op_count++;

		/* loop through all bytes of message i */
		for(j = 0; j < m[i].len; j++) {
			/* insert the data bytes */
			h1 = op_count/3; h2 = op_count%3;
			op[h1] |= cpu_to_le32( (u32)((u8)m[i].buf[j]) << ((3-h2)*8));
			op[h1] |= cpu_to_le32(       SAA7146_I2C_CONT << ((3-h2)*2));
			op_count++;
		}

	}

	/* have a look at the last byte inserted:
          if it was: ...CONT change it to ...STOP */
	h1 = (op_count-1)/3; h2 = (op_count-1)%3;
	if ( SAA7146_I2C_CONT == (0x3 & (le32_to_cpu(op[h1]) >> ((3-h2)*2))) ) {
		op[h1] &= ~cpu_to_le32(0x2 << ((3-h2)*2));
		op[h1] |= cpu_to_le32(SAA7146_I2C_STOP << ((3-h2)*2));
	}

	/* return the number of u32s to send */
	return mem;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
alan cox
alan cox
386
93.46%
1
20.00%
al viro
al viro
23
5.57%
1
20.00%
joe perches
joe perches
2
0.48%
1
20.00%
michael hunold
michael hunold
1
0.24%
1
20.00%
mickey stein
mickey stein
1
0.24%
1
20.00%
Total
413
100.00%
5
100.00%

/* this functions loops through all i2c-messages. normally, it should determine
   which bytes were read through the adapter and write them back to the corresponding
   i2c-message. but instead, we simply write back all bytes.
   fixme: this could be improved. */


static int saa7146_i2c_msg_cleanup(const struct i2c_msg *m, int num, __le32 *op)
{
	int i, j;
	int op_count = 0;

	/* loop through all messages */
	for(i = 0; i < num; i++) {

		op_count++;

		/* loop through all bytes of message i */
		for(j = 0; j < m[i].len; j++) {
			/* write back all bytes that could have been read */
			m[i].buf[j] = (le32_to_cpu(op[op_count/3]) >> ((3-(op_count%3))*8));
			op_count++;
		}
	}

	return 0;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
alan cox
alan cox
105
93.75%
1
20.00%
al viro
al viro
4
3.57%
1
20.00%
mickey stein
mickey stein
1
0.89%
1
20.00%
andre goddard rosa
andre goddard rosa
1
0.89%
1
20.00%
michael hunold
michael hunold
1
0.89%
1
20.00%
Total
112
100.00%
5
100.00%

/* this functions resets the i2c-device and returns 0 if everything was fine, otherwise -1 */


static int saa7146_i2c_reset(struct saa7146_dev *dev)
{
	/* get current status */
	u32 status = saa7146_i2c_status(dev);

	/* clear registers for sure */
	saa7146_write(dev, I2C_STATUS, dev->i2c_bitrate);
	saa7146_write(dev, I2C_TRANSFER, 0);

	/* check if any operation is still in progress */
	if ( 0 != ( status & SAA7146_I2C_BUSY) ) {

		/* yes, kill ongoing operation */
		DEB_I2C("busy_state detected\n");

		/* set "ABORT-OPERATION"-bit (bit 7)*/
		saa7146_write(dev, I2C_STATUS, (dev->i2c_bitrate | MASK_07));
		saa7146_write(dev, MC2, (MASK_00 | MASK_16));
		msleep(SAA7146_I2C_DELAY);

		/* clear all error-bits pending; this is needed because p.123, note 1 */
		saa7146_write(dev, I2C_STATUS, dev->i2c_bitrate);
		saa7146_write(dev, MC2, (MASK_00 | MASK_16));
		msleep(SAA7146_I2C_DELAY);
	}

	/* check if any error is (still) present. (this can be necessary because p.123, note 1) */
	status = saa7146_i2c_status(dev);

	if ( dev->i2c_bitrate != status ) {

		DEB_I2C("error_state detected. status:0x%08x\n", status);

		/* Repeat the abort operation. This seems to be necessary
                   after serious protocol errors caused by e.g. the SAA7740 */
		saa7146_write(dev, I2C_STATUS, (dev->i2c_bitrate | MASK_07));
		saa7146_write(dev, MC2, (MASK_00 | MASK_16));
		msleep(SAA7146_I2C_DELAY);

		/* clear all error-bits pending */
		saa7146_write(dev, I2C_STATUS, dev->i2c_bitrate);
		saa7146_write(dev, MC2, (MASK_00 | MASK_16));
		msleep(SAA7146_I2C_DELAY);

		/* the data sheet says it might be necessary to clear the status
                   twice after an abort */
		saa7146_write(dev, I2C_STATUS, dev->i2c_bitrate);
		saa7146_write(dev, MC2, (MASK_00 | MASK_16));
		msleep(SAA7146_I2C_DELAY);
	}

	/* if any error is still present, a fatal error has occurred ... */
	status = saa7146_i2c_status(dev);
	if ( dev->i2c_bitrate != status ) {
		DEB_I2C("fatal error. status:0x%08x\n", status);
		return -1;
	}

	return 0;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
alan cox
alan cox
265
96.36%
1
20.00%
maximilian attems
maximilian attems
5
1.82%
1
20.00%
joe perches
joe perches
3
1.09%
1
20.00%
lucas de marchi
lucas de marchi
1
0.36%
1
20.00%
michael hunold
michael hunold
1
0.36%
1
20.00%
Total
275
100.00%
5
100.00%

/* this functions writes out the data-byte 'dword' to the i2c-device.
   it returns 0 if ok, -1 if the transfer failed, -2 if the transfer
   failed badly (e.g. address error) */


static int saa7146_i2c_writeout(struct saa7146_dev *dev, __le32 *dword, int short_delay)
{
	u32 status = 0, mc2 = 0;
	int trial = 0;
	unsigned long timeout;

	/* write out i2c-command */
	DEB_I2C("before: 0x%08x (status: 0x%08x), %d\n",
		*dword, saa7146_read(dev, I2C_STATUS), dev->i2c_op);

	if( 0 != (SAA7146_USE_I2C_IRQ & dev->ext->flags)) {

		saa7146_write(dev, I2C_STATUS,	 dev->i2c_bitrate);
		saa7146_write(dev, I2C_TRANSFER, le32_to_cpu(*dword));

		dev->i2c_op = 1;
		SAA7146_ISR_CLEAR(dev, MASK_16|MASK_17);
		SAA7146_IER_ENABLE(dev, MASK_16|MASK_17);
		saa7146_write(dev, MC2, (MASK_00 | MASK_16));

		timeout = HZ/100 + 1; /* 10ms */
		timeout = wait_event_interruptible_timeout(dev->i2c_wq, dev->i2c_op == 0, timeout);
		if (timeout == -ERESTARTSYS || dev->i2c_op) {
			SAA7146_IER_DISABLE(dev, MASK_16|MASK_17);
			SAA7146_ISR_CLEAR(dev, MASK_16|MASK_17);
			if (timeout == -ERESTARTSYS)
				/* a signal arrived */
				return -ERESTARTSYS;

			pr_warn("%s %s [irq]: timed out waiting for end of xfer\n",
				dev->name, __func__);
			return -EIO;
		}
		status = saa7146_read(dev, I2C_STATUS);
	} else {
		saa7146_write(dev, I2C_STATUS,	 dev->i2c_bitrate);
		saa7146_write(dev, I2C_TRANSFER, le32_to_cpu(*dword));
		saa7146_write(dev, MC2, (MASK_00 | MASK_16));

		/* do not poll for i2c-status before upload is complete */
		timeout = jiffies + HZ/100 + 1; /* 10ms */
		while(1) {
			mc2 = (saa7146_read(dev, MC2) & 0x1);
			if( 0 != mc2 ) {
				break;
			}
			if (time_after(jiffies,timeout)) {
				pr_warn("%s %s: timed out waiting for MC2\n",
					dev->name, __func__);
				return -EIO;
			}
		}
		/* wait until we get a transfer done or error */
		timeout = jiffies + HZ/100 + 1; /* 10ms */
		/* first read usually delivers bogus results... */
		saa7146_i2c_status(dev);
		while(1) {
			status = saa7146_i2c_status(dev);
			if ((status & 0x3) != 1)
				break;
			if (time_after(jiffies,timeout)) {
				/* this is normal when probing the bus
                                 * (no answer from nonexisistant device...)
                                 */
				pr_warn("%s %s [poll]: timed out waiting for end of xfer\n",
					dev->name, __func__);
				return -EIO;
			}
			if (++trial < 50 && short_delay)
				udelay(10);
			else
				msleep(1);
		}
	}

	/* give a detailed status report */
	if ( 0 != (status & (SAA7146_I2C_SPERR | SAA7146_I2C_APERR |
			     SAA7146_I2C_DTERR | SAA7146_I2C_DRERR |
			     SAA7146_I2C_AL    | SAA7146_I2C_ERR   |
			     SAA7146_I2C_BUSY)) ) {

		if ( 0 == (status & SAA7146_I2C_ERR) ||
		     0 == (status & SAA7146_I2C_BUSY) ) {
			/* it may take some time until ERR goes high - ignore */
			DEB_I2C("unexpected i2c status %04x\n", status);
		}
		if( 0 != (status & SAA7146_I2C_SPERR) ) {
			DEB_I2C("error due to invalid start/stop condition\n");
		}
		if( 0 != (status & SAA7146_I2C_DTERR) ) {
			DEB_I2C("error in data transmission\n");
		}
		if( 0 != (status & SAA7146_I2C_DRERR) ) {
			DEB_I2C("error when receiving data\n");
		}
		if( 0 != (status & SAA7146_I2C_AL) ) {
			DEB_I2C("error because arbitration lost\n");
		}

		/* we handle address-errors here */
		if( 0 != (status & SAA7146_I2C_APERR) ) {
			DEB_I2C("error in address phase\n");
			return -EREMOTEIO;
		}

		return -EIO;
	}

	/* read back data, just in case we were reading ... */
	*dword = cpu_to_le32(saa7146_read(dev, I2C_TRANSFER));

	DEB_I2C("after: 0x%08x\n", *dword);
	return 0;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
alan cox
alan cox
400
67.23%
1
8.33%
oliver endriss
oliver endriss
66
11.09%
2
16.67%
hartmut birr
hartmut birr
62
10.42%
1
8.33%
michael hunold
michael hunold
30
5.04%
3
25.00%
joe perches
joe perches
13
2.18%
1
8.33%
andrew morton
andrew morton
10
1.68%
1
8.33%
al viro
al viro
10
1.68%
1
8.33%
harvey harrison
harvey harrison
3
0.50%
1
8.33%
maximilian attems
maximilian attems
1
0.17%
1
8.33%
Total
595
100.00%
12
100.00%



static int saa7146_i2c_transfer(struct saa7146_dev *dev, const struct i2c_msg *msgs, int num, int retries)
{
	int i = 0, count = 0;
	__le32 *buffer = dev->d_i2c.cpu_addr;
	int err = 0;
	int short_delay = 0;

	if (mutex_lock_interruptible(&dev->i2c_lock))
		return -ERESTARTSYS;

	for(i=0;i<num;i++) {
		DEB_I2C("msg:%d/%d\n", i+1, num);
	}

	/* prepare the message(s), get number of u32s to transfer */
	count = saa7146_i2c_msg_prepare(msgs, num, buffer);
	if ( 0 > count ) {
		err = -1;
		goto out;
	}

	if ( count > 3 || 0 != (SAA7146_I2C_SHORT_DELAY & dev->ext->flags) )
		short_delay = 1;

	do {
		/* reset the i2c-device if necessary */
		err = saa7146_i2c_reset(dev);
		if ( 0 > err ) {
			DEB_I2C("could not reset i2c-device\n");
			goto out;
		}

		/* write out the u32s one after another */
		for(i = 0; i < count; i++) {
			err = saa7146_i2c_writeout(dev, &buffer[i], short_delay);
			if ( 0 != err) {
				/* this one is unsatisfying: some i2c slaves on some
                                   dvb cards don't acknowledge correctly, so the saa7146
                                   thinks that an address error occurred. in that case, the
                                   transaction should be retrying, even if an address error
                                   occurred. analog saa7146 based cards extensively rely on
                                   i2c address probing, however, and address errors indicate that a
                                   device is really *not* there. retrying in that case
                                   increases the time the device needs to probe greatly, so
                                   it should be avoided. So we bail out in irq mode after an
                                   address error and trust the saa7146 address error detection. */
				if (-EREMOTEIO == err && 0 != (SAA7146_USE_I2C_IRQ & dev->ext->flags))
					goto out;
				DEB_I2C("error while sending message(s). starting again\n");
				break;
			}
		}
		if( 0 == err ) {
			err = num;
			break;
		}

		/* delay a bit before retrying */
		msleep(10);

	} while (err != num && retries--);

	/* quit if any error occurred */
	if (err != num)
		goto out;

	/* if any things had to be read, get the results */
	if ( 0 != saa7146_i2c_msg_cleanup(msgs, num, buffer)) {
		DEB_I2C("could not cleanup i2c-message\n");
		err = -1;
		goto out;
	}

	/* return the number of delivered messages */
	DEB_I2C("transmission successful. (msg:%d)\n", err);
out:
	/* another bug in revision 0: the i2c-registers get uploaded randomly by other
           uploads, so we better clear them out before continuing */
	if( 0 == dev->revision ) {
		__le32 zero = 0;
		saa7146_i2c_reset(dev);
		if( 0 != saa7146_i2c_writeout(dev, &zero, short_delay)) {
			pr_info("revision 0 error. this should never happen\n");
		}
	}

	mutex_unlock(&dev->i2c_lock);
	return err;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
alan cox
alan cox
312
84.78%
1
8.33%
michael hunold
michael hunold
21
5.71%
2
16.67%
andrew morton
andrew morton
12
3.26%
1
8.33%
joe perches
joe perches
9
2.45%
1
8.33%
oliver endriss
oliver endriss
6
1.63%
2
16.67%
lucas de marchi
lucas de marchi
2
0.54%
1
8.33%
ingo molnar
ingo molnar
2
0.54%
1
8.33%
al viro
al viro
2
0.54%
1
8.33%
maximilian attems
maximilian attems
1
0.27%
1
8.33%
mickey stein
mickey stein
1
0.27%
1
8.33%
Total
368
100.00%
12
100.00%

/* utility functions */


static int saa7146_i2c_xfer(struct i2c_adapter* adapter, struct i2c_msg *msg, int num)
{
	struct v4l2_device *v4l2_dev = i2c_get_adapdata(adapter);
	struct saa7146_dev *dev = to_saa7146_dev(v4l2_dev);

	/* use helper function to transfer data */
	return saa7146_i2c_transfer(dev, msg, num, adapter->retries);
}


Contributors
Person
Tokens
Prop
Commits
CommitProp
alan cox
alan cox
40
74.07%
1
25.00%
hans verkuil
hans verkuil
12
22.22%
1
25.00%
michael hunold
michael hunold
1
1.85%
1
25.00%
mickey stein
mickey stein
1
1.85%
1
25.00%
Total
54
100.00%
4
100.00%

/*****************************************************************************/
/* i2c-adapter helper functions                                              */

/* exported algorithm data */

static struct i2c_algorithm saa7146_algo = {
	.master_xfer	= saa7146_i2c_xfer,
	.functionality	= saa7146_i2c_func,
};



int saa7146_i2c_adapter_prepare(struct saa7146_dev *dev, struct i2c_adapter *i2c_adapter, u32 bitrate)
{
	DEB_EE("bitrate: 0x%08x\n", bitrate);

	/* enable i2c-port pins */
	saa7146_write(dev, MC1, (MASK_08 | MASK_24));

	dev->i2c_bitrate = bitrate;
	saa7146_i2c_reset(dev);

	if (i2c_adapter) {
		i2c_set_adapdata(i2c_adapter, &dev->v4l2_dev);
		i2c_adapter->dev.parent    = &dev->pci->dev;
		i2c_adapter->algo	   = &saa7146_algo;
		i2c_adapter->algo_data     = NULL;
		i2c_adapter->timeout = SAA7146_I2C_TIMEOUT;
		i2c_adapter->retries = SAA7146_I2C_RETRIES;
	}

	return 0;
}
Contributors
Person
Tokens
Prop
Commits
CommitProp
alan cox
alan cox
76
71.03%
1
20.00%
andrew morton
andrew morton
14
13.08%
1
20.00%
philipp matthias hahn
philipp matthias hahn
13
12.15%
1
20.00%
hans verkuil
hans verkuil
3
2.80%
1
20.00%
joe perches
joe perches
1
0.93%
1
20.00%
Total
107
100.00%
5
100.00%

Overall Contributors
Person
Tokens
Prop
Commits
CommitProp
alan cox
alan cox
1658
82.45%
1
4.00%
oliver endriss
oliver endriss
72
3.58%
4
16.00%
hartmut birr
hartmut birr
62
3.08%
1
4.00%
michael hunold
michael hunold
57
2.83%
5
20.00%
al viro
al viro
39
1.94%
1
4.00%
joe perches
joe perches
37
1.84%
1
4.00%
andrew morton
andrew morton
36
1.79%
2
8.00%
hans verkuil
hans verkuil
15
0.75%
1
4.00%
philipp matthias hahn
philipp matthias hahn
13
0.65%
1
4.00%
maximilian attems
maximilian attems
7
0.35%
1
4.00%
mickey stein
mickey stein
4
0.20%
1
4.00%
harvey harrison
harvey harrison
3
0.15%
1
4.00%
lucas de marchi
lucas de marchi
3
0.15%
1
4.00%
ingo molnar
ingo molnar
2
0.10%
1
4.00%
mauro carvalho chehab
mauro carvalho chehab
1
0.05%
1
4.00%
johannes stezenbach
johannes stezenbach
1
0.05%
1
4.00%
andre goddard rosa
andre goddard rosa
1
0.05%
1
4.00%
Total
2011
100.00%
25
100.00%
  
Directory: drivers/media/common/saa7146

Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.