cregit-Linux how code gets into the kernel

Release 4.7 drivers/mtd/chips/cfi_probe.c

/*
   Common Flash Interface probe code.
   (C) 2000 Red Hat. GPL'd.
*/

#include <linux/module.h>
#include <linux/types.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <asm/io.h>
#include <asm/byteorder.h>
#include <linux/errno.h>
#include <linux/slab.h>
#include <linux/interrupt.h>

#include <linux/mtd/xip.h>
#include <linux/mtd/map.h>
#include <linux/mtd/cfi.h>
#include <linux/mtd/gen_probe.h>

//#define DEBUG_CFI

#ifdef DEBUG_CFI
static void print_cfi_ident(struct cfi_ident *);
#endif

static int cfi_probe_chip(struct map_info *map, __u32 base,
			  unsigned long *chip_map, struct cfi_private *cfi);
static int cfi_chip_setup(struct map_info *map, struct cfi_private *cfi);

struct mtd_info *cfi_probe(struct map_info *map);

#ifdef CONFIG_MTD_XIP

/* only needed for short periods, so this is rather simple */

#define xip_disable()	local_irq_disable()


#define xip_allowed(base, map) \
do { \
        (void) map_read(map, base); \
        xip_iprefetch(); \
        local_irq_enable(); \
} while (0)


#define xip_enable(base, map, cfi) \
do { \
        cfi_qry_mode_off(base, map, cfi);               \
        xip_allowed(base, map); \
} while (0)


#define xip_disable_qry(base, map, cfi) \
do { \
        xip_disable(); \
        cfi_qry_mode_on(base, map, cfi); \
} while (0)

#else


#define xip_disable()			do { } while (0)

#define xip_allowed(base, map)		do { } while (0)

#define xip_enable(base, map, cfi)	do { } while (0)

#define xip_disable_qry(base, map, cfi) do { } while (0)

#endif

/* check for QRY.
   in: interleave,type,mode
   ret: table index, <0 for error
 */


static int __xipram cfi_probe_chip(struct map_info *map, __u32 base, unsigned long *chip_map, struct cfi_private *cfi) { int i; if ((base + 0) >= map->size) { printk(KERN_NOTICE "Probe at base[0x00](0x%08lx) past the end of the map(0x%08lx)\n", (unsigned long)base, map->size -1); return 0; } if ((base + 0xff) >= map->size) { printk(KERN_NOTICE "Probe at base[0x55](0x%08lx) past the end of the map(0x%08lx)\n", (unsigned long)base + 0x55, map->size -1); return 0; } xip_disable(); if (!cfi_qry_mode_on(base, map, cfi)) { xip_enable(base, map, cfi); return 0; } if (!cfi->numchips) { /* This is the first time we're called. Set up the CFI stuff accordingly and return */ return cfi_chip_setup(map, cfi); } /* Check each previous chip to see if it's an alias */ for (i=0; i < (base >> cfi->chipshift); i++) { unsigned long start; if(!test_bit(i, chip_map)) { /* Skip location; no valid chip at this address */ continue; } start = i << cfi->chipshift; /* This chip should be in read mode if it's one we've already touched. */ if (cfi_qry_present(map, start, cfi)) { /* Eep. This chip also had the QRY marker. * Is it an alias for the new one? */ cfi_qry_mode_off(start, map, cfi); /* If the QRY marker goes away, it's an alias */ if (!cfi_qry_present(map, start, cfi)) { xip_allowed(base, map); printk(KERN_DEBUG "%s: Found an alias at 0x%x for the chip at 0x%lx\n", map->name, base, start); return 0; } /* Yes, it's actually got QRY for data. Most * unfortunate. Stick the new chip in read mode * too and if it's the same, assume it's an alias. */ /* FIXME: Use other modes to do a proper check */ cfi_qry_mode_off(base, map, cfi); if (cfi_qry_present(map, base, cfi)) { xip_allowed(base, map); printk(KERN_DEBUG "%s: Found an alias at 0x%x for the chip at 0x%lx\n", map->name, base, start); return 0; } } } /* OK, if we got to here, then none of the previous chips appear to be aliases for the current one. */ set_bit((base >> cfi->chipshift), chip_map); /* Update chip map */ cfi->numchips++; /* Put it back into Read Mode */ cfi_qry_mode_off(base, map, cfi); xip_allowed(base, map); printk(KERN_INFO "%s: Found %d x%d devices at 0x%x in %d-bit bank\n", map->name, cfi->interleave, cfi->device_type*8, base, map->bankwidth*8); return 1; }

Contributors

PersonTokensPropCommitsCommitProp
david woodhousedavid woodhouse17446.52%444.44%
linus torvaldslinus torvalds10828.88%222.22%
pre-gitpre-git8723.26%111.11%
thomas gleixnerthomas gleixner30.80%111.11%
alexey korolevalexey korolev20.53%111.11%
Total374100.00%9100.00%


static int __xipram cfi_chip_setup(struct map_info *map, struct cfi_private *cfi) { int ofs_factor = cfi->interleave*cfi->device_type; __u32 base = 0; int num_erase_regions = cfi_read_query(map, base + (0x10 + 28)*ofs_factor); int i; int addr_unlock1 = 0x555, addr_unlock2 = 0x2AA; xip_enable(base, map, cfi); #ifdef DEBUG_CFI printk("Number of erase regions: %d\n", num_erase_regions); #endif if (!num_erase_regions) return 0; cfi->cfiq = kmalloc(sizeof(struct cfi_ident) + num_erase_regions * 4, GFP_KERNEL); if (!cfi->cfiq) return 0; memset(cfi->cfiq,0,sizeof(struct cfi_ident)); cfi->cfi_mode = CFI_MODE_CFI; cfi->sector_erase_cmd = CMD(0x30); /* Read the CFI info structure */ xip_disable_qry(base, map, cfi); for (i=0; i<(sizeof(struct cfi_ident) + num_erase_regions * 4); i++) ((unsigned char *)cfi->cfiq)[i] = cfi_read_query(map,base + (0x10 + i)*ofs_factor); /* Do any necessary byteswapping */ cfi->cfiq->P_ID = le16_to_cpu(cfi->cfiq->P_ID); cfi->cfiq->P_ADR = le16_to_cpu(cfi->cfiq->P_ADR); cfi->cfiq->A_ID = le16_to_cpu(cfi->cfiq->A_ID); cfi->cfiq->A_ADR = le16_to_cpu(cfi->cfiq->A_ADR); cfi->cfiq->InterfaceDesc = le16_to_cpu(cfi->cfiq->InterfaceDesc); cfi->cfiq->MaxBufWriteSize = le16_to_cpu(cfi->cfiq->MaxBufWriteSize); #ifdef DEBUG_CFI /* Dump the information therein */ print_cfi_ident(cfi->cfiq); #endif for (i=0; i<cfi->cfiq->NumEraseRegions; i++) { cfi->cfiq->EraseRegionInfo[i] = le32_to_cpu(cfi->cfiq->EraseRegionInfo[i]); #ifdef DEBUG_CFI printk(" Erase Region #%d: BlockSize 0x%4.4X bytes, %d blocks\n", i, (cfi->cfiq->EraseRegionInfo[i] >> 8) & ~0xff, (cfi->cfiq->EraseRegionInfo[i] & 0xffff) + 1); #endif } if (cfi->cfiq->P_ID == P_ID_SST_OLD) { addr_unlock1 = 0x5555; addr_unlock2 = 0x2AAA; } /* * Note we put the device back into Read Mode BEFORE going into Auto * Select Mode, as some devices support nesting of modes, others * don't. This way should always work. * On cmdset 0001 the writes of 0xaa and 0x55 are not needed, and * so should be treated as nops or illegal (and so put the device * back into Read Mode, which is a nop in this case). */ cfi_send_gen_cmd(0xf0, 0, base, map, cfi, cfi->device_type, NULL); cfi_send_gen_cmd(0xaa, addr_unlock1, base, map, cfi, cfi->device_type, NULL); cfi_send_gen_cmd(0x55, addr_unlock2, base, map, cfi, cfi->device_type, NULL); cfi_send_gen_cmd(0x90, addr_unlock1, base, map, cfi, cfi->device_type, NULL); cfi->mfr = cfi_read_query16(map, base); cfi->id = cfi_read_query16(map, base + ofs_factor); /* Get AMD/Spansion extended JEDEC ID */ if (cfi->mfr == CFI_MFR_AMD && (cfi->id & 0xff) == 0x7e) cfi->id = cfi_read_query(map, base + 0xe * ofs_factor) << 8 | cfi_read_query(map, base + 0xf * ofs_factor); /* Put it back into Read Mode */ cfi_qry_mode_off(base, map, cfi); xip_allowed(base, map); printk(KERN_INFO "%s: Found %d x%d devices at 0x%x in %d-bit bank. Manufacturer ID %#08x Chip ID %#08x\n", map->name, cfi->interleave, cfi->device_type*8, base, map->bankwidth*8, cfi->mfr, cfi->id); return 1; }

Contributors

PersonTokensPropCommitsCommitProp
linus torvaldslinus torvalds32652.24%218.18%
guillaume lecerfguillaume lecerf21233.97%545.45%
david woodhousedavid woodhouse477.53%327.27%
pre-gitpre-git396.25%19.09%
Total624100.00%11100.00%

#ifdef DEBUG_CFI
static char *vendorname(__u16 vendor) { switch (vendor) { case P_ID_NONE: return "None"; case P_ID_INTEL_EXT: return "Intel/Sharp Extended"; case P_ID_AMD_STD: return "AMD/Fujitsu Standard"; case P_ID_INTEL_STD: return "Intel/Sharp Standard"; case P_ID_AMD_EXT: return "AMD/Fujitsu Extended"; case P_ID_WINBOND: return "Winbond Standard"; case P_ID_ST_ADV: return "ST Advanced"; case P_ID_MITSUBISHI_STD: return "Mitsubishi Standard"; case P_ID_MITSUBISHI_EXT: return "Mitsubishi Extended"; case P_ID_SST_PAGE: return "SST Page Write"; case P_ID_SST_OLD: return "SST 39VF160x/39VF320x"; case P_ID_INTEL_PERFORMANCE: return "Intel Performance Code"; case P_ID_INTEL_DATA: return "Intel Data"; case P_ID_RESERVED: return "Not Allowed / Reserved for Future Use"; default: return "Unknown"; } }

Contributors

PersonTokensPropCommitsCommitProp
linus torvaldslinus torvalds5956.73%240.00%
david woodhousedavid woodhouse3028.85%120.00%
pre-gitpre-git98.65%120.00%
guillaume lecerfguillaume lecerf65.77%120.00%
Total104100.00%5100.00%


static void print_cfi_ident(struct cfi_ident *cfip) { #if 0 if (cfip->qry[0] != 'Q' || cfip->qry[1] != 'R' || cfip->qry[2] != 'Y') { printk("Invalid CFI ident structure.\n"); return; } #endif printk("Primary Vendor Command Set: %4.4X (%s)\n", cfip->P_ID, vendorname(cfip->P_ID)); if (cfip->P_ADR) printk("Primary Algorithm Table at %4.4X\n", cfip->P_ADR); else printk("No Primary Algorithm Table\n"); printk("Alternative Vendor Command Set: %4.4X (%s)\n", cfip->A_ID, vendorname(cfip->A_ID)); if (cfip->A_ADR) printk("Alternate Algorithm Table at %4.4X\n", cfip->A_ADR); else printk("No Alternate Algorithm Table\n"); printk("Vcc Minimum: %2d.%d V\n", cfip->VccMin >> 4, cfip->VccMin & 0xf); printk("Vcc Maximum: %2d.%d V\n", cfip->VccMax >> 4, cfip->VccMax & 0xf); if (cfip->VppMin) { printk("Vpp Minimum: %2d.%d V\n", cfip->VppMin >> 4, cfip->VppMin & 0xf); printk("Vpp Maximum: %2d.%d V\n", cfip->VppMax >> 4, cfip->VppMax & 0xf); } else printk("No Vpp line\n"); printk("Typical byte/word write timeout: %d µs\n", 1<<cfip->WordWriteTimeoutTyp); printk("Maximum byte/word write timeout: %d µs\n", (1<<cfip->WordWriteTimeoutMax) * (1<<cfip->WordWriteTimeoutTyp)); if (cfip->BufWriteTimeoutTyp || cfip->BufWriteTimeoutMax) { printk("Typical full buffer write timeout: %d µs\n", 1<<cfip->BufWriteTimeoutTyp); printk("Maximum full buffer write timeout: %d µs\n", (1<<cfip->BufWriteTimeoutMax) * (1<<cfip->BufWriteTimeoutTyp)); } else printk("Full buffer write not supported\n"); printk("Typical block erase timeout: %d ms\n", 1<<cfip->BlockEraseTimeoutTyp); printk("Maximum block erase timeout: %d ms\n", (1<<cfip->BlockEraseTimeoutMax) * (1<<cfip->BlockEraseTimeoutTyp)); if (cfip->ChipEraseTimeoutTyp || cfip->ChipEraseTimeoutMax) { printk("Typical chip erase timeout: %d ms\n", 1<<cfip->ChipEraseTimeoutTyp); printk("Maximum chip erase timeout: %d ms\n", (1<<cfip->ChipEraseTimeoutMax) * (1<<cfip->ChipEraseTimeoutTyp)); } else printk("Chip erase not supported\n"); printk("Device size: 0x%X bytes (%d MiB)\n", 1 << cfip->DevSize, 1<< (cfip->DevSize - 20)); printk("Flash Device Interface description: 0x%4.4X\n", cfip->InterfaceDesc); switch(cfip->InterfaceDesc) { case CFI_INTERFACE_X8_ASYNC: printk(" - x8-only asynchronous interface\n"); break; case CFI_INTERFACE_X16_ASYNC: printk(" - x16-only asynchronous interface\n"); break; case CFI_INTERFACE_X8_BY_X16_ASYNC: printk(" - supports x8 and x16 via BYTE# with asynchronous interface\n"); break; case CFI_INTERFACE_X32_ASYNC: printk(" - x32-only asynchronous interface\n"); break; case CFI_INTERFACE_X16_BY_X32_ASYNC: printk(" - supports x16 and x32 via Word# with asynchronous interface\n"); break; case CFI_INTERFACE_NOT_ALLOWED: printk(" - Not Allowed / Reserved\n"); break; default: printk(" - Unknown\n"); break; } printk("Max. bytes in buffer write: 0x%x\n", 1<< cfip->MaxBufWriteSize); printk("Number of Erase Block Regions: %d\n", cfip->NumEraseRegions); }

Contributors

PersonTokensPropCommitsCommitProp
linus torvaldslinus torvalds30266.23%225.00%
pre-gitpre-git12828.07%112.50%
david woodhousedavid woodhouse204.39%450.00%
bartlomiej siekabartlomiej sieka61.32%112.50%
Total456100.00%8100.00%

#endif /* DEBUG_CFI */ static struct chip_probe cfi_chip_probe = { .name = "CFI", .probe_chip = cfi_probe_chip };
struct mtd_info *cfi_probe(struct map_info *map) { /* * Just use the generic probe stuff to call our CFI-specific * chip_probe routine in all the possible permutations, etc. */ return mtd_do_chip_probe(map, &cfi_chip_probe); }

Contributors

PersonTokensPropCommitsCommitProp
linus torvaldslinus torvalds22100.00%2100.00%
Total22100.00%2100.00%

static struct mtd_chip_driver cfi_chipdrv = { .probe = cfi_probe, .name = "cfi_probe", .module = THIS_MODULE };
static int __init cfi_probe_init(void) { register_mtd_chip_driver(&cfi_chipdrv); return 0; }

Contributors

PersonTokensPropCommitsCommitProp
pre-gitpre-git1372.22%125.00%
linus torvaldslinus torvalds422.22%250.00%
adrian bunkadrian bunk15.56%125.00%
Total18100.00%4100.00%


static void __exit cfi_probe_exit(void) { unregister_mtd_chip_driver(&cfi_chipdrv); }

Contributors

PersonTokensPropCommitsCommitProp
pre-gitpre-git960.00%133.33%
linus torvaldslinus torvalds640.00%266.67%
Total15100.00%3100.00%

module_init(cfi_probe_init); module_exit(cfi_probe_exit); MODULE_LICENSE("GPL"); MODULE_AUTHOR("David Woodhouse <dwmw2@infradead.org> et al."); MODULE_DESCRIPTION("Probe code for CFI-compliant flash chips");

Overall Contributors

PersonTokensPropCommitsCommitProp
linus torvaldslinus torvalds91849.06%313.04%
david woodhousedavid woodhouse36319.40%626.09%
pre-gitpre-git34818.60%28.70%
guillaume lecerfguillaume lecerf21811.65%521.74%
art haasart haas100.53%14.35%
bartlomiej siekabartlomiej sieka60.32%14.35%
thomas gleixnerthomas gleixner30.16%14.35%
adrian bunkadrian bunk20.11%28.70%
alexey korolevalexey korolev20.11%14.35%
paulius zaleckaspaulius zaleckas10.05%14.35%
Total1871100.00%23100.00%
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.
{% endraw %}