/* 8530 Serial Communications Controller Register definitions */ #define FLAG 0x7e /* Write Register 0 */ #define R0 0 /* Register selects */ #define R1 1 #define R2 2 #define R3 3 #define R4 4 #define R5 5 #define R6 6 #define R7 7 #define R8 8 #define R9 9 #define R10 10 #define R11 11 #define R12 12 #define R13 13 #define R14 14 #define R15 15 #define NULLCODE 0 /* Null Code */ #define POINT_HIGH 0x8 /* Select upper half of registers */ #define RES_EXT_INT 0x10 /* Reset Ext. Status Interrupts */ #define SEND_ABORT 0x18 /* HDLC Abort */ #define RES_RxINT_FC 0x20 /* Reset RxINT on First Character */ #define RES_Tx_P 0x28 /* Reset TxINT Pending */ #define ERR_RES 0x30 /* Error Reset */ #define RES_H_IUS 0x38 /* Reset highest IUS */ #define RES_Rx_CRC 0x40 /* Reset Rx CRC Checker */ #define RES_Tx_CRC 0x80 /* Reset Tx CRC Checker */ #define RES_EOM_L 0xC0 /* Reset EOM latch */ /* Write Register 1 */ #define EXT_INT_ENAB 0x1 /* Ext Int Enable */ #define TxINT_ENAB 0x2 /* Tx Int Enable */ #define PAR_SPEC 0x4 /* Parity is special condition */ #define RxINT_DISAB 0 /* Rx Int Disable */ #define RxINT_FCERR 0x8 /* Rx Int on First Character Only or Error */ #define INT_ALL_Rx 0x10 /* Int on all Rx Characters or error */ #define INT_ERR_Rx 0x18 /* Int on error only */ #define WT_RDY_RT 0x20 /* Wait/Ready on R/T */ #define WT_FN_RDYFN 0x40 /* Wait/FN/Ready FN */ #define WT_RDY_ENAB 0x80 /* Wait/Ready Enable */ /* Write Register #2 (Interrupt Vector) */ /* Write Register 3 */ #define RxENABLE 0x1 /* Rx Enable */ #define SYNC_L_INH 0x2 /* Sync Character Load Inhibit */ #define ADD_SM 0x4 /* Address Search Mode (SDLC) */ #define RxCRC_ENAB 0x8 /* Rx CRC Enable */ #define ENT_HM 0x10 /* Enter Hunt Mode */ #define AUTO_ENAB 0x20 /* Auto Enables */ #define Rx5 0x0 /* Rx 5 Bits/Character */ #define Rx7 0x40 /* Rx 7 Bits/Character */ #define Rx6 0x80 /* Rx 6 Bits/Character */ #define Rx8 0xc0 /* Rx 8 Bits/Character */ /* Write Register 4 */ #define PAR_ENA 0x1 /* Parity Enable */ #define PAR_EVEN 0x2 /* Parity Even/Odd* */ #define SYNC_ENAB 0 /* Sync Modes Enable */ #define SB1 0x4 /* 1 stop bit/char */ #define SB15 0x8 /* 1.5 stop bits/char */ #define SB2 0xc /* 2 stop bits/char */ #define MONSYNC 0 /* 8 Bit Sync character */ #define BISYNC 0x10 /* 16 bit sync character */ #define SDLC 0x20 /* SDLC Mode (01111110 Sync Flag) */ #define EXTSYNC 0x30 /* External Sync Mode */ #define X1CLK 0x0 /* x1 clock mode */ #define X16CLK 0x40 /* x16 clock mode */ #define X32CLK 0x80 /* x32 clock mode */ #define X64CLK 0xC0 /* x64 clock mode */ /* Write Register 5 */ #define TxCRC_ENAB 0x1 /* Tx CRC Enable */ #define RTS 0x2 /* RTS */ #define SDLC_CRC 0x4 /* SDLC/CRC-16 */ #define TxENAB 0x8 /* Tx Enable */ #define SND_BRK 0x10 /* Send Break */ #define Tx5 0x0 /* Tx 5 bits (or less)/character */ #define Tx7 0x20 /* Tx 7 bits/character */ #define Tx6 0x40 /* Tx 6 bits/character */ #define Tx8 0x60 /* Tx 8 bits/character */ #define DTR 0x80 /* DTR */ /* Write Register 6 (Sync bits 0-7/SDLC Address Field) */ /* Write Register 7 (Sync bits 8-15/SDLC 01111110) */ /* Write Register 8 (transmit buffer) */ /* Write Register 9 (Master interrupt control) */ #define VIS 1 /* Vector Includes Status */ #define NV 2 /* No Vector */ #define DLC 4 /* Disable Lower Chain */ #define MIE 8 /* Master Interrupt Enable */ #define STATHI 0x10 /* Status high */ #define NORESET 0 /* No reset on write to R9 */ #define CHRB 0x40 /* Reset channel B */ #define CHRA 0x80 /* Reset channel A */ #define FHWRES 0xc0 /* Force hardware reset */ /* Write Register 10 (misc control bits) */ #define BIT6 1 /* 6 bit/8bit sync */ #define LOOPMODE 2 /* SDLC Loop mode */ #define ABUNDER 4 /* Abort/flag on SDLC xmit underrun */ #define MARKIDLE 8 /* Mark/flag on idle */ #define GAOP 0x10 /* Go active on poll */ #define NRZ 0 /* NRZ mode */ #define NRZI 0x20 /* NRZI mode */ #define FM1 0x40 /* FM1 (transition = 1) */ #define FM0 0x60 /* FM0 (transition = 0) */ #define CRCPS 0x80 /* CRC Preset I/O */ /* Write Register 11 (Clock Mode control) */ #define TRxCXT 0 /* TRxC = Xtal output */ #define TRxCTC 1 /* TRxC = Transmit clock */ #define TRxCBR 2 /* TRxC = BR Generator Output */ #define TRxCDP 3 /* TRxC = DPLL output */ #define TRxCOI 4 /* TRxC O/I */ #define TCRTxCP 0 /* Transmit clock = RTxC pin */ #define TCTRxCP 8 /* Transmit clock = TRxC pin */ #define TCBR 0x10 /* Transmit clock = BR Generator output */ #define TCDPLL 0x18 /* Transmit clock = DPLL output */ #define RCRTxCP 0 /* Receive clock = RTxC pin */ #define RCTRxCP 0x20 /* Receive clock = TRxC pin */ #define RCBR 0x40 /* Receive clock = BR Generator output */ #define RCDPLL 0x60 /* Receive clock = DPLL output */ #define RTxCX 0x80 /* RTxC Xtal/No Xtal */ /* Write Register 12 (lower byte of baud rate generator time constant) */ /* Write Register 13 (upper byte of baud rate generator time constant) */ /* Write Register 14 (Misc control bits) */ #define BRENABL 1 /* Baud rate generator enable */ #define BRSRC 2 /* Baud rate generator source */ #define DTRREQ 4 /* DTR/Request function */ #define AUTOECHO 8 /* Auto Echo */ #define LOOPBAK 0x10 /* Local loopback */ #define SEARCH 0x20 /* Enter search mode */ #define RMC 0x40 /* Reset missing clock */ #define DISDPLL 0x60 /* Disable DPLL */ #define SSBR 0x80 /* Set DPLL source = BR generator */ #define SSRTxC 0xa0 /* Set DPLL source = RTxC */ #define SFMM 0xc0 /* Set FM mode */ #define SNRZI 0xe0 /* Set NRZI mode */ /* Write Register 15 (external/status interrupt control) */ #define ZCIE 2 /* Zero count IE */ #define DCDIE 8 /* DCD IE */ #define SYNCIE 0x10 /* Sync/hunt IE */ #define CTSIE 0x20 /* CTS IE */ #define TxUIE 0x40 /* Tx Underrun/EOM IE */ #define BRKIE 0x80 /* Break/Abort IE */ /* Read Register 0 */ #define Rx_CH_AV 0x1 /* Rx Character Available */ #define ZCOUNT 0x2 /* Zero count */ #define Tx_BUF_EMP 0x4 /* Tx Buffer empty */ #define DCD 0x8 /* DCD */ #define SYNC_HUNT 0x10 /* Sync/hunt */ #define CTS 0x20 /* CTS */ #define TxEOM 0x40 /* Tx underrun */ #define BRK_ABRT 0x80 /* Break/Abort */ /* Read Register 1 */ #define ALL_SNT 0x1 /* All sent */ /* Residue Data for 8 Rx bits/char programmed */ #define RES3 0x8 /* 0/3 */ #define RES4 0x4 /* 0/4 */ #define RES5 0xc /* 0/5 */ #define RES6 0x2 /* 0/6 */ #define RES7 0xa /* 0/7 */ #define RES8 0x6 /* 0/8 */ #define RES18 0xe /* 1/8 */ #define RES28 0x0 /* 2/8 */ /* Special Rx Condition Interrupts */ #define PAR_ERR 0x10 /* Parity error */ #define Rx_OVR 0x20 /* Rx Overrun Error */ #define CRC_ERR 0x40 /* CRC/Framing Error */ #define END_FR 0x80 /* End of Frame (SDLC) */ /* Read Register 2 (channel b only) - Interrupt vector */ /* Read Register 3 (interrupt pending register) ch a only */ #define CHBEXT 0x1 /* Channel B Ext/Stat IP */ #define CHBTxIP 0x2 /* Channel B Tx IP */ #define CHBRxIP 0x4 /* Channel B Rx IP */ #define CHAEXT 0x8 /* Channel A Ext/Stat IP */ #define CHATxIP 0x10 /* Channel A Tx IP */ #define CHARxIP 0x20 /* Channel A Rx IP */ /* Read Register 8 (receive data register) */ /* Read Register 10 (misc status bits) */ #define ONLOOP 2 /* On loop */ #define LOOPSEND 0x10 /* Loop sending */ #define CLK2MIS 0x40 /* Two clocks missing */ #define CLK1MIS 0x80 /* One clock missing */ /* Read Register 12 (lower byte of baud rate generator constant) */ /* Read Register 13 (upper byte of baud rate generator constant) */ /* Read Register 15 (value of WR 15) */ /* Z85C30/Z85230 Enhanced SCC register definitions */ /* Write Register 7' (SDLC/HDLC Programmable Enhancements) */ #define AUTOTXF 0x01 /* Auto Tx Flag */ #define AUTOEOM 0x02 /* Auto EOM Latch Reset */ #define AUTORTS 0x04 /* Auto RTS */ #define TXDNRZI 0x08 /* TxD Pulled High in SDLC NRZI mode */ #define RXFIFOH 0x08 /* Z85230: Int on RX FIFO half full */ #define FASTDTR 0x10 /* Fast DTR/REQ Mode */ #define CRCCBCR 0x20 /* CRC Check Bytes Completely Received */ #define TXFIFOE 0x20 /* Z85230: Int on TX FIFO completely empty */ #define EXTRDEN 0x40 /* Extended Read Enabled */ /* Write Register 15 (external/status interrupt control) */ #define SHDLCE 1 /* SDLC/HDLC Enhancements Enable */ #define FIFOE 4 /* FIFO Enable */ /* Read Register 6 (frame status FIFO) */ #define BCLSB 0xff /* LSB of 14 bits count */ /* Read Register 7 (frame status FIFO) */ #define BCMSB 0x3f /* MSB of 14 bits count */ #define FDA 0x40 /* FIFO Data Available Status */ #define FOS 0x80 /* FIFO Overflow Status */Overall Contributors
| Person | Tokens | Prop | Commits | CommitProp | |
| pre-git | pre-git | 862 | 100.00% | 3 | 100.00% |
| Total | 862 | 100.00% | 3 | 100.00% |