cregit-Linux how code gets into the kernel

Release 4.7 drivers/pcmcia/o2micro.h

Directory: drivers/pcmcia
/*
 * o2micro.h 1.13 1999/10/25 20:03:34
 *
 * The contents of this file are subject to the Mozilla Public License
 * Version 1.1 (the "License"); you may not use this file except in
 * compliance with the License. You may obtain a copy of the License
 * at http://www.mozilla.org/MPL/
 *
 * Software distributed under the License is distributed on an "AS IS"
 * basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See
 * the License for the specific language governing rights and
 * limitations under the License. 
 *
 * The initial developer of the original code is David A. Hinds
 * <dahinds@users.sourceforge.net>.  Portions created by David A. Hinds
 * are Copyright (C) 1999 David A. Hinds.  All Rights Reserved.
 *
 * Alternatively, the contents of this file may be used under the
 * terms of the GNU General Public License version 2 (the "GPL"), in which
 * case the provisions of the GPL are applicable instead of the
 * above.  If you wish to allow the use of your version of this file
 * only under the terms of the GPL and not to allow others to use
 * your version of this file under the MPL, indicate your decision by
 * deleting the provisions above and replace them with the notice and
 * other provisions required by the GPL.  If you do not delete the
 * provisions above, a recipient may use your version of this file
 * under either the MPL or the GPL.
 */

#ifndef _LINUX_O2MICRO_H

#define _LINUX_O2MICRO_H

/* Additional PCI configuration registers */


#define O2_MUX_CONTROL		0x90	
/* 32 bit */

#define  O2_MUX_RING_OUT	0x0000000f

#define  O2_MUX_SKTB_ACTV	0x000000f0

#define  O2_MUX_SCTA_ACTV_ENA	0x00000100

#define  O2_MUX_SCTB_ACTV_ENA	0x00000200

#define  O2_MUX_SER_IRQ_ROUTE	0x0000e000

#define  O2_MUX_SER_PCI		0x00010000


#define  O2_MUX_SKTA_TURBO	0x000c0000	
/* for 6833, 6860 */

#define  O2_MUX_SKTB_TURBO	0x00300000

#define  O2_MUX_AUX_VCC_3V	0x00400000

#define  O2_MUX_PCI_VCC_5V	0x00800000

#define  O2_MUX_PME_MUX		0x0f000000

/* Additional ExCA registers */


#define O2_MODE_A		0x38

#define O2_MODE_A_2		0x26	
/* for 6833B, 6860C */

#define  O2_MODE_A_CD_PULSE	0x04

#define  O2_MODE_A_SUSP_EDGE	0x08

#define  O2_MODE_A_HOST_SUSP	0x10

#define  O2_MODE_A_PWR_MASK	0x60

#define  O2_MODE_A_QUIET	0x80


#define O2_MODE_B		0x39

#define O2_MODE_B_2		0x2e	
/* for 6833B, 6860C */

#define  O2_MODE_B_IDENT	0x03

#define  O2_MODE_B_ID_BSTEP	0x00

#define  O2_MODE_B_ID_CSTEP	0x01

#define  O2_MODE_B_ID_O2	0x02

#define  O2_MODE_B_VS1		0x04

#define  O2_MODE_B_VS2		0x08

#define  O2_MODE_B_IRQ15_RI	0x80


#define O2_MODE_C		0x3a

#define  O2_MODE_C_DREQ_MASK	0x03

#define  O2_MODE_C_DREQ_INPACK	0x01

#define  O2_MODE_C_DREQ_WP	0x02

#define  O2_MODE_C_DREQ_BVD2	0x03

#define  O2_MODE_C_ZVIDEO	0x08

#define  O2_MODE_C_IREQ_SEL	0x30

#define  O2_MODE_C_MGMT_SEL	0xc0


#define O2_MODE_D		0x3b

#define  O2_MODE_D_IRQ_MODE	0x03

#define  O2_MODE_D_PCI_CLKRUN	0x04

#define  O2_MODE_D_CB_CLKRUN	0x08

#define  O2_MODE_D_SKT_ACTV	0x20

#define  O2_MODE_D_PCI_FIFO	0x40	
/* for OZ6729, OZ6730 */

#define  O2_MODE_D_W97_IRQ	0x40

#define  O2_MODE_D_ISA_IRQ	0x80


#define O2_MHPG_DMA		0x3c

#define  O2_MHPG_CHANNEL	0x07

#define  O2_MHPG_CINT_ENA	0x08

#define  O2_MHPG_CSC_ENA	0x10


#define O2_FIFO_ENA		0x3d

#define  O2_FIFO_ZVIDEO_3	0x08

#define  O2_FIFO_PCI_FIFO	0x10

#define  O2_FIFO_POSTWR		0x40

#define  O2_FIFO_BUFFER		0x80


#define O2_MODE_E		0x3e

#define  O2_MODE_E_MHPG_DMA	0x01

#define  O2_MODE_E_SPKR_OUT	0x02

#define  O2_MODE_E_LED_OUT	0x08

#define  O2_MODE_E_SKTA_ACTV	0x10


#define O2_RESERVED1		0x94

#define O2_RESERVED2		0xD4

#define O2_RES_READ_PREFETCH	0x02

#define O2_RES_WRITE_BURST	0x08




static int o2micro_override(struct yenta_socket *socket)
{
	/*
         * 'reserved' register at 0x94/D4. allows setting read prefetch and write
         * bursting. read prefetching for example makes the RME Hammerfall DSP
         * working. for some bridges it is at 0x94, for others at 0xD4. it's
         * ok to write to both registers on all O2 bridges.
         * from Eric Still, 02Micro.
         */
	u8 a, b;
	bool use_speedup;

	if (PCI_FUNC(socket->dev->devfn) == 0) {
		a = config_readb(socket, O2_RESERVED1);
		b = config_readb(socket, O2_RESERVED2);
		dev_dbg(&socket->dev->dev, "O2: 0x94/0xD4: %02x/%02x\n", a, b);

		switch (socket->dev->device) {
		/*
                 * older bridges have problems with both read prefetch and write
                 * bursting depending on the combination of the chipset, bridge
                 * and the cardbus card. so disable them to be on the safe side.
                 */
		case PCI_DEVICE_ID_O2_6729:
		case PCI_DEVICE_ID_O2_6730:
		case PCI_DEVICE_ID_O2_6812:
		case PCI_DEVICE_ID_O2_6832:
		case PCI_DEVICE_ID_O2_6836:
		case PCI_DEVICE_ID_O2_6933:
			use_speedup = false;
			break;
		default:
			use_speedup = true;
			break;
		}

		/* the user may override our decision */
		if (strcasecmp(o2_speedup, "on") == 0)
			use_speedup = true;
		else if (strcasecmp(o2_speedup, "off") == 0)
			use_speedup = false;
		else if (strcasecmp(o2_speedup, "default") != 0)
			dev_warn(&socket->dev->dev,
				"O2: Unknown parameter, using 'default'");

		if (use_speedup) {
			dev_info(&socket->dev->dev,
				"O2: enabling read prefetch/write burst. If you experience problems or performance issues, use the yenta_socket parameter 'o2_speedup=off'\n");
			config_writeb(socket, O2_RESERVED1,
				      a | O2_RES_READ_PREFETCH | O2_RES_WRITE_BURST);
			config_writeb(socket, O2_RESERVED2,
				      b | O2_RES_READ_PREFETCH | O2_RES_WRITE_BURST);
		} else {
			dev_info(&socket->dev->dev,
				"O2: disabling read prefetch/write burst. If you experience problems or performance issues, use the yenta_socket parameter 'o2_speedup=on'\n");
			config_writeb(socket, O2_RESERVED1,
				      a & ~(O2_RES_READ_PREFETCH | O2_RES_WRITE_BURST));
			config_writeb(socket, O2_RESERVED2,
				      b & ~(O2_RES_READ_PREFETCH | O2_RES_WRITE_BURST));
		}
	}

	return 0;
}


Contributors
PersonTokensPropCommitsCommitProp
daniel ritzdaniel ritz14054.05%342.86%


wolfram sangwolfram sang9436.29%228.57%


dominik brodowskidominik brodowski228.49%114.29%


tomas kovaciktomas kovacik31.16%114.29%


Total259100.00%7100.00%






static void o2micro_restore_state(struct yenta_socket *socket)
{
	/*
         * as long as read prefetch is the only thing in
         * o2micro_override, it's safe to call it from here
         */
	o2micro_override(socket);
}


Contributors
PersonTokensPropCommitsCommitProp
daniel ritzdaniel ritz17100.00%1100.00%


Total17100.00%1100.00%



#endif /* _LINUX_O2MICRO_H */

Overall Contributors
PersonTokensPropCommitsCommitProp
pre-gitpre-git24845.84%220.00%


daniel ritzdaniel ritz17331.98%330.00%


wolfram sangwolfram sang9417.38%220.00%


dominik brodowskidominik brodowski224.07%110.00%


tomas kovaciktomas kovacik30.55%110.00%


david hindsdavid hinds10.18%110.00%


Total541100.00%10100.00%

  
Directory: drivers/pcmcia



Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.
{% endraw %}