cregit-Linux how code gets into the kernel

Release 4.7 drivers/rtc/rtc-bfin.c

Directory: drivers/rtc
/*
 * Blackfin On-Chip Real Time Clock Driver
 *  Supports BF51x/BF52x/BF53[123]/BF53[467]/BF54x
 *
 * Copyright 2004-2010 Analog Devices Inc.
 *
 * Enter bugs at http://blackfin.uclinux.org/
 *
 * Licensed under the GPL-2 or later.
 */

/* The biggest issue we deal with in this driver is that register writes are
 * synced to the RTC frequency of 1Hz.  So if you write to a register and
 * attempt to write again before the first write has completed, the new write
 * is simply discarded.  This can easily be troublesome if userspace disables
 * one event (say periodic) and then right after enables an event (say alarm).
 * Since all events are maintained in the same interrupt mask register, if
 * we wrote to it to disable the first event and then wrote to it again to
 * enable the second event, that second event would not be enabled as the
 * write would be discarded and things quickly fall apart.
 *
 * To keep this delay from significantly degrading performance (we, in theory,
 * would have to sleep for up to 1 second every time we wanted to write a
 * register), we only check the write pending status before we start to issue
 * a new write.  We bank on the idea that it doesn't matter when the sync
 * happens so long as we don't attempt another write before it does.  The only
 * time userspace would take this penalty is when they try and do multiple
 * operations right after another ... but in this case, they need to take the
 * sync penalty, so we should be OK.
 *
 * Also note that the RTC_ISTAT register does not suffer this penalty; its
 * writes to clear status registers complete immediately.
 */

/* It may seem odd that there is no SWCNT code in here (which would be exposed
 * via the periodic interrupt event, or PIE).  Since the Blackfin RTC peripheral
 * runs in units of seconds (N/HZ) but the Linux framework runs in units of HZ
 * (2^N HZ), there is no point in keeping code that only provides 1 HZ PIEs.
 * The same exact behavior can be accomplished by using the update interrupt
 * event (UIE).  Maybe down the line the RTC peripheral will suck less in which
 * case we can re-introduce PIE support.
 */

#include <linux/bcd.h>
#include <linux/completion.h>
#include <linux/delay.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/rtc.h>
#include <linux/seq_file.h>
#include <linux/slab.h>

#include <asm/blackfin.h>


#define dev_dbg_stamp(dev) dev_dbg(dev, "%s:%i: here i am\n", __func__, __LINE__)


struct bfin_rtc {
	
struct rtc_device *rtc_dev;
	
struct rtc_time rtc_alarm;
	
u16 rtc_wrote_regs;
};

/* Bit values for the ISTAT / ICTL registers */

#define RTC_ISTAT_WRITE_COMPLETE  0x8000

#define RTC_ISTAT_WRITE_PENDING   0x4000

#define RTC_ISTAT_ALARM_DAY       0x0040

#define RTC_ISTAT_24HR            0x0020

#define RTC_ISTAT_HOUR            0x0010

#define RTC_ISTAT_MIN             0x0008

#define RTC_ISTAT_SEC             0x0004

#define RTC_ISTAT_ALARM           0x0002

#define RTC_ISTAT_STOPWATCH       0x0001

/* Shift values for RTC_STAT register */

#define DAY_BITS_OFF    17

#define HOUR_BITS_OFF   12

#define MIN_BITS_OFF    6

#define SEC_BITS_OFF    0

/* Some helper functions to convert between the common RTC notion of time
 * and the internal Blackfin notion that is encoded in 32bits.
 */

static inline u32 rtc_time_to_bfin(unsigned long now) { u32 sec = (now % 60); u32 min = (now % (60 * 60)) / 60; u32 hour = (now % (60 * 60 * 24)) / (60 * 60); u32 days = (now / (60 * 60 * 24)); return (sec << SEC_BITS_OFF) + (min << MIN_BITS_OFF) + (hour << HOUR_BITS_OFF) + (days << DAY_BITS_OFF); }

Contributors

PersonTokensPropCommitsCommitProp
bryan wubryan wu96100.00%1100.00%
Total96100.00%1100.00%


static inline unsigned long rtc_bfin_to_time(u32 rtc_bfin) { return (((rtc_bfin >> SEC_BITS_OFF) & 0x003F)) + (((rtc_bfin >> MIN_BITS_OFF) & 0x003F) * 60) + (((rtc_bfin >> HOUR_BITS_OFF) & 0x001F) * 60 * 60) + (((rtc_bfin >> DAY_BITS_OFF) & 0x7FFF) * 60 * 60 * 24); }

Contributors

PersonTokensPropCommitsCommitProp
bryan wubryan wu72100.00%1100.00%
Total72100.00%1100.00%


static inline void rtc_bfin_to_tm(u32 rtc_bfin, struct rtc_time *tm) { rtc_time_to_tm(rtc_bfin_to_time(rtc_bfin), tm); }

Contributors

PersonTokensPropCommitsCommitProp
bryan wubryan wu25100.00%1100.00%
Total25100.00%1100.00%

/** * bfin_rtc_sync_pending - make sure pending writes have complete * * Wait for the previous write to a RTC register to complete. * Unfortunately, we can't sleep here as that introduces a race condition when * turning on interrupt events. Consider this: * - process sets alarm * - process enables alarm * - process sleeps while waiting for rtc write to sync * - interrupt fires while process is sleeping * - interrupt acks the event by writing to ISTAT * - interrupt sets the WRITE PENDING bit * - interrupt handler finishes * - process wakes up, sees WRITE PENDING bit set, goes to sleep * - interrupt fires while process is sleeping * If anyone can point out the obvious solution here, i'm listening :). This * shouldn't be an issue on an SMP or preempt system as this function should * only be called with the rtc lock held. * * Other options: * - disable PREN so the sync happens at 32.768kHZ ... but this changes the * inc rate for all RTC registers from 1HZ to 32.768kHZ ... * - use the write complete IRQ */ /* static void bfin_rtc_sync_pending_polled(void) { while (!(bfin_read_RTC_ISTAT() & RTC_ISTAT_WRITE_COMPLETE)) if (!(bfin_read_RTC_ISTAT() & RTC_ISTAT_WRITE_PENDING)) break; bfin_write_RTC_ISTAT(RTC_ISTAT_WRITE_COMPLETE); } */ static DECLARE_COMPLETION(bfin_write_complete);
static void bfin_rtc_sync_pending(struct device *dev) { dev_dbg_stamp(dev); while (bfin_read_RTC_ISTAT() & RTC_ISTAT_WRITE_PENDING) wait_for_completion_timeout(&bfin_write_complete, HZ * 5); dev_dbg_stamp(dev); }

Contributors

PersonTokensPropCommitsCommitProp
mike frysingermike frysinger2257.89%150.00%
bryan wubryan wu1642.11%150.00%
Total38100.00%2100.00%

/** * bfin_rtc_reset - set RTC to sane/known state * * Initialize the RTC. Enable pre-scaler to scale RTC clock * to 1Hz and clear interrupt/status registers. */
static void bfin_rtc_reset(struct device *dev, u16 rtc_ictl) { struct bfin_rtc *rtc = dev_get_drvdata(dev); dev_dbg_stamp(dev); bfin_rtc_sync_pending(dev); bfin_write_RTC_PREN(0x1); bfin_write_RTC_ICTL(rtc_ictl); bfin_write_RTC_ALARM(0); bfin_write_RTC_ISTAT(0xFFFF); rtc->rtc_wrote_regs = 0; }

Contributors

PersonTokensPropCommitsCommitProp
bryan wubryan wu3456.67%125.00%
mike frysingermike frysinger2643.33%375.00%
Total60100.00%4100.00%

/** * bfin_rtc_interrupt - handle interrupt from RTC * * Since we handle all RTC events here, we have to make sure the requested * interrupt is enabled (in RTC_ICTL) as the event status register (RTC_ISTAT) * always gets updated regardless of the interrupt being enabled. So when one * even we care about (e.g. stopwatch) goes off, we don't want to turn around * and say that other events have happened as well (e.g. second). We do not * have to worry about pending writes to the RTC_ICTL register as interrupts * only fire if they are enabled in the RTC_ICTL register. */
static irqreturn_t bfin_rtc_interrupt(int irq, void *dev_id) { struct device *dev = dev_id; struct bfin_rtc *rtc = dev_get_drvdata(dev); unsigned long events = 0; bool write_complete = false; u16 rtc_istat, rtc_istat_clear, rtc_ictl, bits; dev_dbg_stamp(dev); rtc_istat = bfin_read_RTC_ISTAT(); rtc_ictl = bfin_read_RTC_ICTL(); rtc_istat_clear = 0; bits = RTC_ISTAT_WRITE_COMPLETE; if (rtc_istat & bits) { rtc_istat_clear |= bits; write_complete = true; complete(&bfin_write_complete); } bits = (RTC_ISTAT_ALARM | RTC_ISTAT_ALARM_DAY); if (rtc_ictl & bits) { if (rtc_istat & bits) { rtc_istat_clear |= bits; events |= RTC_AF | RTC_IRQF; } } bits = RTC_ISTAT_SEC; if (rtc_ictl & bits) { if (rtc_istat & bits) { rtc_istat_clear |= bits; events |= RTC_UF | RTC_IRQF; } } if (events) rtc_update_irq(rtc->rtc_dev, 1, events); if (write_complete || events) { bfin_write_RTC_ISTAT(rtc_istat_clear); return IRQ_HANDLED; } else return IRQ_NONE; }

Contributors

PersonTokensPropCommitsCommitProp
mike frysingermike frysinger11157.22%480.00%
bryan wubryan wu8342.78%120.00%
Total194100.00%5100.00%


static void bfin_rtc_int_set(u16 rtc_int) { bfin_write_RTC_ISTAT(rtc_int); bfin_write_RTC_ICTL(bfin_read_RTC_ICTL() | rtc_int); }

Contributors

PersonTokensPropCommitsCommitProp
mike frysingermike frysinger22100.00%1100.00%
Total22100.00%1100.00%


static void bfin_rtc_int_clear(u16 rtc_int) { bfin_write_RTC_ICTL(bfin_read_RTC_ICTL() & rtc_int); }

Contributors

PersonTokensPropCommitsCommitProp
mike frysingermike frysinger17100.00%1100.00%
Total17100.00%1100.00%


static void bfin_rtc_int_set_alarm(struct bfin_rtc *rtc) { /* Blackfin has different bits for whether the alarm is * more than 24 hours away. */ bfin_rtc_int_set(rtc->rtc_alarm.tm_yday == -1 ? RTC_ISTAT_ALARM : RTC_ISTAT_ALARM_DAY); }

Contributors

PersonTokensPropCommitsCommitProp
mike frysingermike frysinger28100.00%1100.00%
Total28100.00%1100.00%


static int bfin_rtc_alarm_irq_enable(struct device *dev, unsigned int enabled) { struct bfin_rtc *rtc = dev_get_drvdata(dev); dev_dbg_stamp(dev); if (enabled) bfin_rtc_int_set_alarm(rtc); else bfin_rtc_int_clear(~(RTC_ISTAT_ALARM | RTC_ISTAT_ALARM_DAY)); return 0; }

Contributors

PersonTokensPropCommitsCommitProp
john stultzjohn stultz3260.38%120.00%
bryan wubryan wu1324.53%120.00%
mike frysingermike frysinger815.09%360.00%
Total53100.00%5100.00%


static int bfin_rtc_read_time(struct device *dev, struct rtc_time *tm) { struct bfin_rtc *rtc = dev_get_drvdata(dev); dev_dbg_stamp(dev); if (rtc->rtc_wrote_regs & 0x1) bfin_rtc_sync_pending(dev); rtc_bfin_to_tm(bfin_read_RTC_STAT(), tm); return 0; }

Contributors

PersonTokensPropCommitsCommitProp
bryan wubryan wu4276.36%133.33%
mike frysingermike frysinger1323.64%266.67%
Total55100.00%3100.00%


static int bfin_rtc_set_time(struct device *dev, struct rtc_time *tm) { struct bfin_rtc *rtc = dev_get_drvdata(dev); int ret; unsigned long now; dev_dbg_stamp(dev); ret = rtc_tm_to_time(tm, &now); if (ret == 0) { if (rtc->rtc_wrote_regs & 0x1) bfin_rtc_sync_pending(dev); bfin_write_RTC_STAT(rtc_time_to_bfin(now)); rtc->rtc_wrote_regs = 0x1; } return ret; }

Contributors

PersonTokensPropCommitsCommitProp
bryan wubryan wu6676.74%133.33%
mike frysingermike frysinger2023.26%266.67%
Total86100.00%3100.00%


static int bfin_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alrm) { struct bfin_rtc *rtc = dev_get_drvdata(dev); dev_dbg_stamp(dev); alrm->time = rtc->rtc_alarm; bfin_rtc_sync_pending(dev); alrm->enabled = !!(bfin_read_RTC_ICTL() & (RTC_ISTAT_ALARM | RTC_ISTAT_ALARM_DAY)); return 0; }

Contributors

PersonTokensPropCommitsCommitProp
bryan wubryan wu5382.81%120.00%
mike frysingermike frysinger1117.19%480.00%
Total64100.00%5100.00%


static int bfin_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alrm) { struct bfin_rtc *rtc = dev_get_drvdata(dev); unsigned long rtc_alarm; dev_dbg_stamp(dev); if (rtc_tm_to_time(&alrm->time, &rtc_alarm)) return -EINVAL; rtc->rtc_alarm = alrm->time; bfin_rtc_sync_pending(dev); bfin_write_RTC_ALARM(rtc_time_to_bfin(rtc_alarm)); if (alrm->enabled) bfin_rtc_int_set_alarm(rtc); return 0; }

Contributors

PersonTokensPropCommitsCommitProp
mike frysingermike frysinger5057.47%375.00%
bryan wubryan wu3742.53%125.00%
Total87100.00%4100.00%


static int bfin_rtc_proc(struct device *dev, struct seq_file *seq) { #define yesno(x) ((x) ? "yes" : "no") u16 ictl = bfin_read_RTC_ICTL(); dev_dbg_stamp(dev); seq_printf(seq, "alarm_IRQ\t: %s\n" "wkalarm_IRQ\t: %s\n" "seconds_IRQ\t: %s\n", yesno(ictl & RTC_ISTAT_ALARM), yesno(ictl & RTC_ISTAT_ALARM_DAY), yesno(ictl & RTC_ISTAT_SEC)); return 0; #undef yesno }

Contributors

PersonTokensPropCommitsCommitProp
bryan wubryan wu6085.71%133.33%
mike frysingermike frysinger1014.29%266.67%
Total70100.00%3100.00%

static struct rtc_class_ops bfin_rtc_ops = { .read_time = bfin_rtc_read_time, .set_time = bfin_rtc_set_time, .read_alarm = bfin_rtc_read_alarm, .set_alarm = bfin_rtc_set_alarm, .proc = bfin_rtc_proc, .alarm_irq_enable = bfin_rtc_alarm_irq_enable, };
static int bfin_rtc_probe(struct platform_device *pdev) { struct bfin_rtc *rtc; struct device *dev = &pdev->dev; int ret; unsigned long timeout = jiffies + HZ; dev_dbg_stamp(dev); /* Allocate memory for our RTC struct */ rtc = devm_kzalloc(dev, sizeof(*rtc), GFP_KERNEL); if (unlikely(!rtc)) return -ENOMEM; platform_set_drvdata(pdev, rtc); device_init_wakeup(dev, 1); /* Register our RTC with the RTC framework */ rtc->rtc_dev = devm_rtc_device_register(dev, pdev->name, &bfin_rtc_ops, THIS_MODULE); if (IS_ERR(rtc->rtc_dev)) return PTR_ERR(rtc->rtc_dev); /* Grab the IRQ and init the hardware */ ret = devm_request_irq(dev, IRQ_RTC, bfin_rtc_interrupt, 0, pdev->name, dev); if (unlikely(ret)) dev_err(&pdev->dev, "unable to request IRQ; alarm won't work, " "and writes will be delayed\n"); /* sometimes the bootloader touched things, but the write complete was not * enabled, so let's just do a quick timeout here since the IRQ will not fire ... */ while (bfin_read_RTC_ISTAT() & RTC_ISTAT_WRITE_PENDING) if (time_after(jiffies, timeout)) break; bfin_rtc_reset(dev, RTC_ISTAT_WRITE_COMPLETE); bfin_write_RTC_SWCNT(0); return 0; }

Contributors

PersonTokensPropCommitsCommitProp
mike frysingermike frysinger13470.16%666.67%
bryan wubryan wu4724.61%111.11%
jingoo hanjingoo han94.71%111.11%
michael hennerichmichael hennerich10.52%111.11%
Total191100.00%9100.00%


static int bfin_rtc_remove(struct platform_device *pdev) { struct device *dev = &pdev->dev; bfin_rtc_reset(dev, 0); return 0; }

Contributors

PersonTokensPropCommitsCommitProp
mike frysingermike frysinger1651.61%150.00%
bryan wubryan wu1548.39%150.00%
Total31100.00%2100.00%

#ifdef CONFIG_PM_SLEEP
static int bfin_rtc_suspend(struct device *dev) { dev_dbg_stamp(dev); if (device_may_wakeup(dev)) { enable_irq_wake(IRQ_RTC); bfin_rtc_sync_pending(dev); } else bfin_rtc_int_clear(0); return 0; }

Contributors

PersonTokensPropCommitsCommitProp
mike frysingermike frysinger2454.55%466.67%
sonic zhangsonic zhang1840.91%116.67%
jingoo hanjingoo han24.55%116.67%
Total44100.00%6100.00%


static int bfin_rtc_resume(struct device *dev) { dev_dbg_stamp(dev); if (device_may_wakeup(dev)) disable_irq_wake(IRQ_RTC); /* * Since only some of the RTC bits are maintained externally in the * Vbat domain, we need to wait for the RTC MMRs to be synced into * the core after waking up. This happens every RTC 1HZ. Once that * has happened, we can go ahead and re-enable the important write * complete interrupt event. */ while (!(bfin_read_RTC_ISTAT() & RTC_ISTAT_SEC)) continue; bfin_rtc_int_set(RTC_ISTAT_WRITE_COMPLETE); return 0; }

Contributors

PersonTokensPropCommitsCommitProp
mike frysingermike frysinger3164.58%360.00%
sonic zhangsonic zhang1531.25%120.00%
jingoo hanjingoo han24.17%120.00%
Total48100.00%5100.00%

#endif static SIMPLE_DEV_PM_OPS(bfin_rtc_pm_ops, bfin_rtc_suspend, bfin_rtc_resume); static struct platform_driver bfin_rtc_driver = { .driver = { .name = "rtc-bfin", .pm = &bfin_rtc_pm_ops, }, .probe = bfin_rtc_probe, .remove = bfin_rtc_remove, }; module_platform_driver(bfin_rtc_driver); MODULE_DESCRIPTION("Blackfin On-Chip Real Time Clock Driver"); MODULE_AUTHOR("Mike Frysinger <vapier@gentoo.org>"); MODULE_LICENSE("GPL"); MODULE_ALIAS("platform:rtc-bfin");

Overall Contributors

PersonTokensPropCommitsCommitProp
bryan wubryan wu83354.84%13.23%
mike frysingermike frysinger57237.66%2167.74%
john stultzjohn stultz372.44%13.23%
sonic zhangsonic zhang372.44%13.23%
jingoo hanjingoo han281.84%26.45%
kay sieverskay sievers50.33%13.23%
tejun heotejun heo30.20%13.23%
axel linaxel lin20.13%13.23%
lucas de marchilucas de marchi10.07%13.23%
michael hennerichmichael hennerich10.07%13.23%
Total1519100.00%31100.00%
Directory: drivers/rtc
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.
{% endraw %}