cregit-Linux how code gets into the kernel

Release 4.7 drivers/scsi/NCR5380.h

Directory: drivers/scsi
/* 
 * NCR 5380 defines
 *
 * Copyright 1993, Drew Eckhardt
 *      Visionary Computing
 *      (Unix consulting and custom programming)
 *      drew@colorado.edu
 *      +1 (303) 666-5836
 *
 * For more information, please consult 
 *
 * NCR 5380 Family
 * SCSI Protocol Controller
 * Databook
 * NCR Microelectronics
 * 1635 Aeroplaza Drive
 * Colorado Springs, CO 80916
 * 1+ (719) 578-3400
 * 1+ (800) 334-5454
 */

#ifndef NCR5380_H

#define NCR5380_H

#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/list.h>
#include <linux/workqueue.h>
#include <scsi/scsi_dbg.h>
#include <scsi/scsi_eh.h>
#include <scsi/scsi_transport_spi.h>


#define NDEBUG_ARBITRATION	0x1

#define NDEBUG_AUTOSENSE	0x2

#define NDEBUG_DMA		0x4

#define NDEBUG_HANDSHAKE	0x8

#define NDEBUG_INFORMATION	0x10

#define NDEBUG_INIT		0x20

#define NDEBUG_INTR		0x40

#define NDEBUG_LINKED		0x80

#define NDEBUG_MAIN		0x100

#define NDEBUG_NO_DATAOUT	0x200

#define NDEBUG_NO_WRITE		0x400

#define NDEBUG_PIO		0x800

#define NDEBUG_PSEUDO_DMA	0x1000

#define NDEBUG_QUEUES		0x2000

#define NDEBUG_RESELECTION	0x4000

#define NDEBUG_SELECTION	0x8000

#define NDEBUG_USLEEP		0x10000

#define NDEBUG_LAST_BYTE_SENT	0x20000

#define NDEBUG_RESTART_SELECT	0x40000

#define NDEBUG_EXTENDED		0x80000

#define NDEBUG_C400_PREAD	0x100000

#define NDEBUG_C400_PWRITE	0x200000

#define NDEBUG_LISTS		0x400000

#define NDEBUG_ABORT		0x800000

#define NDEBUG_TAGS		0x1000000

#define NDEBUG_MERGING		0x2000000


#define NDEBUG_ANY		0xFFFFFFFFUL

/* 
 * The contents of the OUTPUT DATA register are asserted on the bus when
 * either arbitration is occurring or the phase-indicating signals (
 * IO, CD, MSG) in the TARGET COMMAND register and the ASSERT DATA
 * bit in the INITIATOR COMMAND register is set.
 */


#define OUTPUT_DATA_REG         0	
/* wo DATA lines on SCSI bus */

#define CURRENT_SCSI_DATA_REG   0	
/* ro same */


#define INITIATOR_COMMAND_REG	1	
/* rw */

#define ICR_ASSERT_RST		0x80	
/* rw Set to assert RST  */

#define ICR_ARBITRATION_PROGRESS 0x40	
/* ro Indicates arbitration complete */

#define ICR_TRI_STATE		0x40	
/* wo Set to tri-state drivers */

#define ICR_ARBITRATION_LOST	0x20	
/* ro Indicates arbitration lost */

#define ICR_DIFF_ENABLE		0x20	
/* wo Set to enable diff. drivers */

#define ICR_ASSERT_ACK		0x10	
/* rw ini Set to assert ACK */

#define ICR_ASSERT_BSY		0x08	
/* rw Set to assert BSY */

#define ICR_ASSERT_SEL 		0x04	
/* rw Set to assert SEL */

#define ICR_ASSERT_ATN		0x02	
/* rw Set to assert ATN */

#define ICR_ASSERT_DATA		0x01	
/* rw SCSI_DATA_REG is asserted */

#ifdef DIFFERENTIAL

#define ICR_BASE		ICR_DIFF_ENABLE
#else

#define ICR_BASE		0
#endif


#define MODE_REG		2
/*
 * Note : BLOCK_DMA code will keep DRQ asserted for the duration of the 
 * transfer, causing the chip to hog the bus.  You probably don't want 
 * this.
 */

#define MR_BLOCK_DMA_MODE	0x80	
/* rw block mode DMA */

#define MR_TARGET		0x40	
/* rw target mode */

#define MR_ENABLE_PAR_CHECK	0x20	
/* rw enable parity checking */

#define MR_ENABLE_PAR_INTR	0x10	
/* rw enable bad parity interrupt */

#define MR_ENABLE_EOP_INTR	0x08	
/* rw enable eop interrupt */

#define MR_MONITOR_BSY		0x04	
/* rw enable int on unexpected bsy fail */

#define MR_DMA_MODE		0x02	
/* rw DMA / pseudo DMA mode */

#define MR_ARBITRATE		0x01	
/* rw start arbitration */

#ifdef PARITY

#define MR_BASE			MR_ENABLE_PAR_CHECK
#else

#define MR_BASE			0
#endif


#define TARGET_COMMAND_REG	3

#define TCR_LAST_BYTE_SENT	0x80	
/* ro DMA done */

#define TCR_ASSERT_REQ		0x08	
/* tgt rw assert REQ */

#define TCR_ASSERT_MSG		0x04	
/* tgt rw assert MSG */

#define TCR_ASSERT_CD		0x02	
/* tgt rw assert CD */

#define TCR_ASSERT_IO		0x01	
/* tgt rw assert IO */


#define STATUS_REG		4	
/* ro */
/*
 * Note : a set bit indicates an active signal, driven by us or another 
 * device.
 */

#define SR_RST			0x80

#define SR_BSY			0x40

#define SR_REQ			0x20

#define SR_MSG			0x10

#define SR_CD			0x08

#define SR_IO			0x04

#define SR_SEL			0x02

#define SR_DBP			0x01

/*
 * Setting a bit in this register will cause an interrupt to be generated when 
 * BSY is false and SEL true and this bit is asserted  on the bus.
 */

#define SELECT_ENABLE_REG	4	
/* wo */


#define BUS_AND_STATUS_REG	5	
/* ro */

#define BASR_END_DMA_TRANSFER	0x80	
/* ro set on end of transfer */

#define BASR_DRQ		0x40	
/* ro mirror of DRQ pin */

#define BASR_PARITY_ERROR	0x20	
/* ro parity error detected */

#define BASR_IRQ		0x10	
/* ro mirror of IRQ pin */

#define BASR_PHASE_MATCH	0x08	
/* ro Set when MSG CD IO match TCR */

#define BASR_BUSY_ERROR		0x04	
/* ro Unexpected change to inactive state */

#define BASR_ATN 		0x02	
/* ro BUS status */

#define BASR_ACK		0x01	
/* ro BUS status */

/* Write any value to this register to start a DMA send */

#define START_DMA_SEND_REG	5	
/* wo */

/* 
 * Used in DMA transfer mode, data is latched from the SCSI bus on
 * the falling edge of REQ (ini) or ACK (tgt)
 */

#define INPUT_DATA_REG			6	
/* ro */

/* Write any value to this register to start a DMA receive */

#define START_DMA_TARGET_RECEIVE_REG	6	
/* wo */

/* Read this register to clear interrupt conditions */

#define RESET_PARITY_INTERRUPT_REG	7	
/* ro */

/* Write any value to this register to start an ini mode DMA receive */

#define START_DMA_INITIATOR_RECEIVE_REG 7	
/* wo */

/* NCR 53C400(A) Control Status Register bits: */

#define CSR_RESET              0x80	
/* wo  Resets 53c400 */

#define CSR_53C80_REG          0x80	
/* ro  5380 registers busy */

#define CSR_TRANS_DIR          0x40	
/* rw  Data transfer direction */

#define CSR_SCSI_BUFF_INTR     0x20	
/* rw  Enable int on transfer ready */

#define CSR_53C80_INTR         0x10	
/* rw  Enable 53c80 interrupts */

#define CSR_SHARED_INTR        0x08	
/* rw  Interrupt sharing */

#define CSR_HOST_BUF_NOT_RDY   0x04	
/* ro  Is Host buffer ready */

#define CSR_SCSI_BUF_RDY       0x02	
/* ro  SCSI buffer read */

#define CSR_GATED_53C80_IRQ    0x01	
/* ro  Last block xferred */

#if 0
#define CSR_BASE CSR_SCSI_BUFF_INTR | CSR_53C80_INTR
#else

#define CSR_BASE CSR_53C80_INTR
#endif

/* Note : PHASE_* macros are based on the values of the STATUS register */

#define PHASE_MASK 	(SR_MSG | SR_CD | SR_IO)


#define PHASE_DATAOUT		0

#define PHASE_DATAIN		SR_IO

#define PHASE_CMDOUT		SR_CD

#define PHASE_STATIN		(SR_CD | SR_IO)

#define PHASE_MSGOUT		(SR_MSG | SR_CD)

#define PHASE_MSGIN		(SR_MSG | SR_CD | SR_IO)

#define PHASE_UNKNOWN		0xff

/* 
 * Convert status register phase to something we can use to set phase in 
 * the target register so we can get phase mismatch interrupts on DMA 
 * transfers.
 */


#define PHASE_SR_TO_TCR(phase) ((phase) >> 2)

/*
 * These are "special" values for the irq and dma_channel fields of the 
 * Scsi_Host structure
 */


#define DMA_NONE	255

#define IRQ_AUTO	254

#define DMA_AUTO	254

#define PORT_AUTO	0xffff	
/* autoprobe io port for 53c400a */

#ifndef NO_IRQ

#define NO_IRQ		0
#endif


#define FLAG_DMA_FIXUP			1	
/* Use DMA errata workarounds */

#define FLAG_NO_PSEUDO_DMA		8	
/* Inhibit DMA */

#define FLAG_LATE_DMA_SETUP		32	
/* Setup NCR before DMA H/W */

#define FLAG_TOSHIBA_DELAY		128	
/* Allow for borken CD-ROMs */


struct NCR5380_hostdata {
	
NCR5380_implementation_fields;		/* implementation specific */
	
struct Scsi_Host *host;			/* Host backpointer */
	

unsigned char id_mask, id_higher_mask;	/* 1 << id, all bits greater */
	
unsigned char busy[8];			/* index = target, bit = lun */
	
int dma_len;				/* requested length of DMA */
	
unsigned char last_message;		/* last message OUT */
	
struct scsi_cmnd *connected;		/* currently connected cmnd */
	
struct scsi_cmnd *selecting;		/* cmnd to be connected */
	
struct list_head unissued;		/* waiting to be issued */
	
struct list_head autosense;		/* priority issue queue */
	
struct list_head disconnected;		/* waiting for reconnect */
	
spinlock_t lock;			/* protects this struct */
	
int flags;
	
struct scsi_eh_save ses;
	
struct scsi_cmnd *sensing;
	
char info[256];
	
int read_overruns;                /* number of bytes to cut from a
                                           * transfer to handle chip overruns */
	
struct work_struct main_task;
	
struct workqueue_struct *work_q;
	
unsigned long accesses_per_ms;	/* chip register accesses per ms */
};

#ifdef __KERNEL__


struct NCR5380_cmd {
	
struct list_head list;
};


#define NCR5380_CMD_SIZE		(sizeof(struct NCR5380_cmd))


static inline struct scsi_cmnd *NCR5380_to_scmd(struct NCR5380_cmd *ncmd_ptr) { return ((struct scsi_cmnd *)ncmd_ptr) - 1; }

Contributors

PersonTokensPropCommitsCommitProp
finn thainfinn thain26100.00%1100.00%
Total26100.00%1100.00%

#ifndef NDEBUG #define NDEBUG (0) #endif #define dprintk(flg, fmt, ...) \ do { if ((NDEBUG) & (flg)) \ printk(KERN_DEBUG fmt, ## __VA_ARGS__); } while (0) #define dsprintk(flg, host, fmt, ...) \ do { if ((NDEBUG) & (flg)) \ shost_printk(KERN_DEBUG, host, fmt, ## __VA_ARGS__); \ } while (0) #if NDEBUG #define NCR5380_dprint(flg, arg) \ do { if ((NDEBUG) & (flg)) NCR5380_print(arg); } while (0) #define NCR5380_dprint_phase(flg, arg) \ do { if ((NDEBUG) & (flg)) NCR5380_print_phase(arg); } while (0) static void NCR5380_print_phase(struct Scsi_Host *instance); static void NCR5380_print(struct Scsi_Host *instance); #else #define NCR5380_dprint(flg, arg) do {} while (0) #define NCR5380_dprint_phase(flg, arg) do {} while (0) #endif static int NCR5380_probe_irq(struct Scsi_Host *instance, int possible); static int NCR5380_init(struct Scsi_Host *instance, int flags); static int NCR5380_maybe_reset_bus(struct Scsi_Host *); static void NCR5380_exit(struct Scsi_Host *instance); static void NCR5380_information_transfer(struct Scsi_Host *instance); static irqreturn_t NCR5380_intr(int irq, void *dev_id); static void NCR5380_main(struct work_struct *work); static const char *NCR5380_info(struct Scsi_Host *instance); static void NCR5380_reselect(struct Scsi_Host *instance); static struct scsi_cmnd *NCR5380_select(struct Scsi_Host *, struct scsi_cmnd *); static int NCR5380_transfer_dma(struct Scsi_Host *instance, unsigned char *phase, int *count, unsigned char **data); static int NCR5380_transfer_pio(struct Scsi_Host *instance, unsigned char *phase, int *count, unsigned char **data); static int NCR5380_poll_politely(struct Scsi_Host *, int, int, int, int); static int NCR5380_poll_politely2(struct Scsi_Host *, int, int, int, int, int, int, int); #endif /* __KERNEL__ */ #endif /* NCR5380_H */

Overall Contributors

PersonTokensPropCommitsCommitProp
pre-gitpre-git69367.22%922.50%
finn thainfinn thain28727.84%2357.50%
dave jonesdave jones161.55%12.50%
james bottomleyjames bottomley100.97%12.50%
alan coxalan cox90.87%12.50%
boaz harroshboaz harrosh70.68%12.50%
andrew mortonandrew morton40.39%12.50%
david howellsdavid howells30.29%12.50%
linus torvaldslinus torvalds10.10%12.50%
ondrej zaryondrej zary10.10%12.50%
Total1031100.00%40100.00%
Directory: drivers/scsi
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.
{% endraw %}