Release 4.7 drivers/scsi/aha152x.h
#ifndef _AHA152X_H
#define _AHA152X_H
/*
* $Id: aha152x.h,v 2.7 2004/01/24 11:39:03 fischer Exp $
*/
/* number of queueable commands
(unless we support more than 1 cmd_per_lun this should do) */
#define AHA152X_MAXQUEUE 7
#define AHA152X_REVID "Adaptec 152x SCSI driver; $Revision: 2.7 $"
/* port addresses */
#define SCSISEQ (HOSTIOPORT0+0x00)
/* SCSI sequence control */
#define SXFRCTL0 (HOSTIOPORT0+0x01)
/* SCSI transfer control 0 */
#define SXFRCTL1 (HOSTIOPORT0+0x02)
/* SCSI transfer control 1 */
#define SCSISIG (HOSTIOPORT0+0x03)
/* SCSI signal in/out */
#define SCSIRATE (HOSTIOPORT0+0x04)
/* SCSI rate control */
#define SELID (HOSTIOPORT0+0x05)
/* selection/reselection ID */
#define SCSIID SELID
/* SCSI ID */
#define SCSIDAT (HOSTIOPORT0+0x06)
/* SCSI latched data */
#define SCSIBUS (HOSTIOPORT0+0x07)
/* SCSI data bus */
#define STCNT0 (HOSTIOPORT0+0x08)
/* SCSI transfer count 0 */
#define STCNT1 (HOSTIOPORT0+0x09)
/* SCSI transfer count 1 */
#define STCNT2 (HOSTIOPORT0+0x0a)
/* SCSI transfer count 2 */
#define SSTAT0 (HOSTIOPORT0+0x0b)
/* SCSI interrupt status 0 */
#define SSTAT1 (HOSTIOPORT0+0x0c)
/* SCSI interrupt status 1 */
#define SSTAT2 (HOSTIOPORT0+0x0d)
/* SCSI interrupt status 2 */
#define SCSITEST (HOSTIOPORT0+0x0e)
/* SCSI test control */
#define SSTAT3 SCSITEST
/* SCSI interrupt status 3 */
#define SSTAT4 (HOSTIOPORT0+0x0f)
/* SCSI status 4 */
#define SIMODE0 (HOSTIOPORT1+0x10)
/* SCSI interrupt mode 0 */
#define SIMODE1 (HOSTIOPORT1+0x11)
/* SCSI interrupt mode 1 */
#define DMACNTRL0 (HOSTIOPORT1+0x12)
/* DMA control 0 */
#define DMACNTRL1 (HOSTIOPORT1+0x13)
/* DMA control 1 */
#define DMASTAT (HOSTIOPORT1+0x14)
/* DMA status */
#define FIFOSTAT (HOSTIOPORT1+0x15)
/* FIFO status */
#define DATAPORT (HOSTIOPORT1+0x16)
/* DATA port */
#define BRSTCNTRL (HOSTIOPORT1+0x18)
/* burst control */
#define PORTA (HOSTIOPORT1+0x1a)
/* PORT A */
#define PORTB (HOSTIOPORT1+0x1b)
/* PORT B */
#define REV (HOSTIOPORT1+0x1c)
/* revision */
#define STACK (HOSTIOPORT1+0x1d)
/* stack */
#define TEST (HOSTIOPORT1+0x1e)
/* test register */
#define IO_RANGE 0x20
/* used in aha152x_porttest */
#define O_PORTA 0x1a
/* PORT A */
#define O_PORTB 0x1b
/* PORT B */
#define O_DMACNTRL1 0x13
/* DMA control 1 */
#define O_STACK 0x1d
/* stack */
/* used in tc1550_porttest */
#define O_TC_PORTA 0x0a
/* PORT A */
#define O_TC_PORTB 0x0b
/* PORT B */
#define O_TC_DMACNTRL1 0x03
/* DMA control 1 */
#define O_TC_STACK 0x0d
/* stack */
/* bits and bitmasks to ports */
/* SCSI sequence control */
#define TEMODEO 0x80
#define ENSELO 0x40
#define ENSELI 0x20
#define ENRESELI 0x10
#define ENAUTOATNO 0x08
#define ENAUTOATNI 0x04
#define ENAUTOATNP 0x02
#define SCSIRSTO 0x01
/* SCSI transfer control 0 */
#define SCSIEN 0x80
#define DMAEN 0x40
#define CH1 0x20
#define CLRSTCNT 0x10
#define SPIOEN 0x08
#define CLRCH1 0x02
/* SCSI transfer control 1 */
#define BITBUCKET 0x80
#define SWRAPEN 0x40
#define ENSPCHK 0x20
#define STIMESEL 0x18
/* mask */
#define STIMESEL_ 3
#define ENSTIMER 0x04
#define BYTEALIGN 0x02
/* SCSI signal IN */
#define SIG_CDI 0x80
#define SIG_IOI 0x40
#define SIG_MSGI 0x20
#define SIG_ATNI 0x10
#define SIG_SELI 0x08
#define SIG_BSYI 0x04
#define SIG_REQI 0x02
#define SIG_ACKI 0x01
/* SCSI Phases */
#define P_MASK (SIG_MSGI|SIG_CDI|SIG_IOI)
#define P_DATAO (0)
#define P_DATAI (SIG_IOI)
#define P_CMD (SIG_CDI)
#define P_STATUS (SIG_CDI|SIG_IOI)
#define P_MSGO (SIG_MSGI|SIG_CDI)
#define P_MSGI (SIG_MSGI|SIG_CDI|SIG_IOI)
/* SCSI signal OUT */
#define SIG_CDO 0x80
#define SIG_IOO 0x40
#define SIG_MSGO 0x20
#define SIG_ATNO 0x10
#define SIG_SELO 0x08
#define SIG_BSYO 0x04
#define SIG_REQO 0x02
#define SIG_ACKO 0x01
/* SCSI rate control */
#define SXFR 0x70
/* mask */
#define SXFR_ 4
#define SOFS 0x0f
/* mask */
/* SCSI ID */
#define OID 0x70
#define OID_ 4
#define TID 0x07
/* SCSI transfer count */
#define GETSTCNT() ( (GETPORT(STCNT2)<<16) \
+ (GETPORT(STCNT1)<< 8) \
+ GETPORT(STCNT0) )
#define SETSTCNT(X) { SETPORT(STCNT2, ((X) & 0xFF0000) >> 16); \
SETPORT(STCNT1, ((X) & 0x00FF00) >> 8); \
SETPORT(STCNT0, ((X) & 0x0000FF) ); }
/* SCSI interrupt status */
#define TARGET 0x80
#define SELDO 0x40
#define SELDI 0x20
#define SELINGO 0x10
#define SWRAP 0x08
#define SDONE 0x04
#define SPIORDY 0x02
#define DMADONE 0x01
#define SETSDONE 0x80
#define CLRSELDO 0x40
#define CLRSELDI 0x20
#define CLRSELINGO 0x10
#define CLRSWRAP 0x08
#define CLRSDONE 0x04
#define CLRSPIORDY 0x02
#define CLRDMADONE 0x01
/* SCSI status 1 */
#define SELTO 0x80
#define ATNTARG 0x40
#define SCSIRSTI 0x20
#define PHASEMIS 0x10
#define BUSFREE 0x08
#define SCSIPERR 0x04
#define PHASECHG 0x02
#define REQINIT 0x01
#define CLRSELTIMO 0x80
#define CLRATNO 0x40
#define CLRSCSIRSTI 0x20
#define CLRBUSFREE 0x08
#define CLRSCSIPERR 0x04
#define CLRPHASECHG 0x02
#define CLRREQINIT 0x01
/* SCSI status 2 */
#define SOFFSET 0x20
#define SEMPTY 0x10
#define SFULL 0x08
#define SFCNT 0x07
/* mask */
/* SCSI status 3 */
#define SCSICNT 0xf0
/* mask */
#define SCSICNT_ 4
#define OFFCNT 0x0f
/* mask */
/* SCSI TEST control */
#define SCTESTU 0x08
#define SCTESTD 0x04
#define STCTEST 0x01
/* SCSI status 4 */
#define SYNCERR 0x04
#define FWERR 0x02
#define FRERR 0x01
#define CLRSYNCERR 0x04
#define CLRFWERR 0x02
#define CLRFRERR 0x01
/* SCSI interrupt mode 0 */
#define ENSELDO 0x40
#define ENSELDI 0x20
#define ENSELINGO 0x10
#define ENSWRAP 0x08
#define ENSDONE 0x04
#define ENSPIORDY 0x02
#define ENDMADONE 0x01
/* SCSI interrupt mode 1 */
#define ENSELTIMO 0x80
#define ENATNTARG 0x40
#define ENSCSIRST 0x20
#define ENPHASEMIS 0x10
#define ENBUSFREE 0x08
#define ENSCSIPERR 0x04
#define ENPHASECHG 0x02
#define ENREQINIT 0x01
/* DMA control 0 */
#define ENDMA 0x80
#define _8BIT 0x40
#define DMA 0x20
#define WRITE_READ 0x08
#define INTEN 0x04
#define RSTFIFO 0x02
#define SWINT 0x01
/* DMA control 1 */
#define PWRDWN 0x80
#define STK 0x07
/* mask */
/* DMA status */
#define ATDONE 0x80
#define WORDRDY 0x40
#define INTSTAT 0x20
#define DFIFOFULL 0x10
#define DFIFOEMP 0x08
/* BURST control */
#define BON 0xf0
#define BOFF 0x0f
/* TEST REGISTER */
#define BOFFTMR 0x40
#define BONTMR 0x20
#define STCNTH 0x10
#define STCNTM 0x08
#define STCNTL 0x04
#define SCSIBLK 0x02
#define DMABLK 0x01
/* On the AHA-152x board PORTA and PORTB contain
some information about the board's configuration. */
typedef union {
struct {
unsigned reserved:2; /* reserved */
unsigned tardisc:1; /* Target disconnect: 0=disabled, 1=enabled */
unsigned syncneg:1; /* Initial sync neg: 0=disabled, 1=enabled */
unsigned msgclasses:2; /* Message classes
0=#4
1=#0, #1, #2, #3, #4
2=#0, #3, #4
3=#0, #4
*/
unsigned boot:1; /* boot: 0=disabled, 1=enabled */
unsigned dma:1; /* Transfer mode: 0=PIO; 1=DMA */
unsigned id:3; /* SCSI-id */
unsigned irq:2; /* IRQ-Channel: 0,3=12, 1=10, 2=11 */
unsigned dmachan:2; /* DMA-Channel: 0=0, 1=5, 2=6, 3=7 */
unsigned parity:1; /* SCSI-parity: 1=enabled 0=disabled */
}
fields;
unsigned short port;
}
aha152x_config ;
#define cf_parity fields.parity
#define cf_dmachan fields.dmachan
#define cf_irq fields.irq
#define cf_id fields.id
#define cf_dma fields.dma
#define cf_boot fields.boot
#define cf_msgclasses fields.msgclasses
#define cf_syncneg fields.syncneg
#define cf_tardisc fields.tardisc
#define cf_port port
/* Some macros to manipulate ports and their bits */
#define SETPORT(PORT, VAL) outb( (VAL), (PORT) )
#define GETPORT(PORT) inb( PORT )
#define SETBITS(PORT, BITS) outb( (inb(PORT) | (BITS)), (PORT) )
#define CLRBITS(PORT, BITS) outb( (inb(PORT) & ~(BITS)), (PORT) )
#define TESTHI(PORT, BITS) ((inb(PORT) & (BITS)) == (BITS))
#define TESTLO(PORT, BITS) ((inb(PORT) & (BITS)) == 0)
#define SETRATE(RATE) SETPORT(SCSIRATE,(RATE) & 0x7f)
#if defined(AHA152X_DEBUG)
enum {
debug_procinfo = 0x0001,
debug_queue = 0x0002,
debug_locking = 0x0004,
debug_intr = 0x0008,
debug_selection = 0x0010,
debug_msgo = 0x0020,
debug_msgi = 0x0040,
debug_status = 0x0080,
debug_cmd = 0x0100,
debug_datai = 0x0200,
debug_datao = 0x0400,
debug_eh = 0x0800,
debug_done = 0x1000,
debug_phases = 0x2000,
};
#endif
/* for the pcmcia stub */
struct aha152x_setup {
int io_port;
int irq;
int scsiid;
int reconnect;
int parity;
int synchronous;
int delay;
int ext_trans;
int tc1550;
#if defined(AHA152X_DEBUG)
int debug;
#endif
char *conf;
};
struct Scsi_Host *aha152x_probe_one(struct aha152x_setup *);
void aha152x_release(struct Scsi_Host *);
int aha152x_host_reset_host(struct Scsi_Host *);
#endif /* _AHA152X_H */
Overall Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| pre-git | pre-git | 1043 | 93.12% | 6 | 60.00% |
| christoph hellwig | christoph hellwig | 63 | 5.62% | 1 | 10.00% |
| juergen e. fischer | juergen e. fischer | 13 | 1.16% | 2 | 20.00% |
| boaz harrosh | boaz harrosh | 1 | 0.09% | 1 | 10.00% |
| Total | 1120 | 100.00% | 10 | 100.00% |
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.