Release 4.7 drivers/tty/serial/omap-serial.c

/*
 * Driver for OMAP-UART controller.
 * Based on drivers/serial/8250.c
 *
 * Copyright (C) 2010 Texas Instruments.
 *
 * Authors:
 *      Govindraj R     <govindraj.raja@ti.com>
 *      Thara Gopinath  <thara@ti.com>
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * Note: This driver is made separate from 8250 driver as we cannot
 * over load 8250 driver with omap platform specific configuration for
 * features like DMA, it makes easier to implement features like DMA and
 * hardware flow control and software flow control configuration with
 * this driver as required for the omap-platform.
 */

#if defined(CONFIG_SERIAL_OMAP_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)

#define SUPPORT_SYSRQ
#endif

#include <linux/module.h>
#include <linux/init.h>
#include <linux/console.h>
#include <linux/serial_reg.h>
#include <linux/delay.h>
#include <linux/slab.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/clk.h>
#include <linux/serial_core.h>
#include <linux/irq.h>
#include <linux/pm_runtime.h>
#include <linux/pm_wakeirq.h>
#include <linux/of.h>
#include <linux/of_irq.h>
#include <linux/gpio.h>
#include <linux/of_gpio.h>
#include <linux/platform_data/serial-omap.h>

#include <dt-bindings/gpio/gpio.h>


#define OMAP_MAX_HSUART_PORTS	10


#define UART_BUILD_REVISION(x, y)	(((x) << 8) | (y))


#define OMAP_UART_REV_42 0x0402

#define OMAP_UART_REV_46 0x0406

#define OMAP_UART_REV_52 0x0502

#define OMAP_UART_REV_63 0x0603


#define OMAP_UART_TX_WAKEUP_EN		BIT(7)

/* Feature flags */

#define OMAP_UART_WER_HAS_TX_WAKEUP	BIT(0)


#define UART_ERRATA_i202_MDR1_ACCESS	BIT(0)

#define UART_ERRATA_i291_DMA_FORCEIDLE	BIT(1)


#define DEFAULT_CLK_SPEED 48000000 
/* 48Mhz */

/* SCR register bitmasks */

#define OMAP_UART_SCR_RX_TRIG_GRANU1_MASK		(1 << 7)

#define OMAP_UART_SCR_TX_TRIG_GRANU1_MASK		(1 << 6)

#define OMAP_UART_SCR_TX_EMPTY			(1 << 3)

/* FCR register bitmasks */

#define OMAP_UART_FCR_RX_FIFO_TRIG_MASK			(0x3 << 6)

#define OMAP_UART_FCR_TX_FIFO_TRIG_MASK			(0x3 << 4)

/* MVR register bitmasks */

#define OMAP_UART_MVR_SCHEME_SHIFT	30


#define OMAP_UART_LEGACY_MVR_MAJ_MASK	0xf0

#define OMAP_UART_LEGACY_MVR_MAJ_SHIFT	4

#define OMAP_UART_LEGACY_MVR_MIN_MASK	0x0f


#define OMAP_UART_MVR_MAJ_MASK		0x700

#define OMAP_UART_MVR_MAJ_SHIFT		8

#define OMAP_UART_MVR_MIN_MASK		0x3f


#define OMAP_UART_DMA_CH_FREE	-1


#define MSR_SAVE_FLAGS		UART_MSR_ANY_DELTA

#define OMAP_MODE13X_SPEED	230400

/* WER = 0x7F
 * Enable module level wakeup in WER reg
 */

#define OMAP_UART_WER_MOD_WKUP	0x7F

/* Enable XON/XOFF flow control on output */

#define OMAP_UART_SW_TX		0x08

/* Enable XON/XOFF flow control on input */

#define OMAP_UART_SW_RX		0x02


#define OMAP_UART_SW_CLR	0xF0


#define OMAP_UART_TCR_TRIG	0x0F


struct uart_omap_dma {
	
u8			uart_dma_tx;
	
u8			uart_dma_rx;
	
int			rx_dma_channel;
	
int			tx_dma_channel;
	
dma_addr_t		rx_buf_dma_phys;
	
dma_addr_t		tx_buf_dma_phys;
	
unsigned int		uart_base;
	/*
         * Buffer for rx dma. It is not required for tx because the buffer
         * comes from port structure.
         */
	
unsigned char		*rx_buf;
	
unsigned int		prev_rx_dma_pos;
	
int			tx_buf_size;
	
int			tx_dma_used;
	
int			rx_dma_used;
	
spinlock_t		tx_lock;
	
spinlock_t		rx_lock;
	/* timer to poll activity on rx dma */
	
struct timer_list	rx_timer;
	
unsigned int		rx_buf_size;
	
unsigned int		rx_poll_rate;
	
unsigned int		rx_timeout;
};


struct uart_omap_port {
	
struct uart_port	port;
	
struct uart_omap_dma	uart_dma;
	
struct device		*dev;
	
int			wakeirq;

	
unsigned char		ier;
	
unsigned char		lcr;
	
unsigned char		mcr;
	
unsigned char		fcr;
	
unsigned char		efr;
	
unsigned char		dll;
	
unsigned char		dlh;
	
unsigned char		mdr1;
	
unsigned char		scr;
	
unsigned char		wer;

	
int			use_dma;
	/*
         * Some bits in registers are cleared on a read, so they must
         * be saved whenever the register is read, but the bits will not
         * be immediately processed.
         */
	
unsigned int		lsr_break_flag;
	
unsigned char		msr_saved_flags;
	
char			name[20];
	
unsigned long		port_activity;
	
int			context_loss_cnt;
	
u32			errata;
	
u32			features;

	
int			rts_gpio;

	
struct pm_qos_request	pm_qos_request;
	
u32			latency;
	
u32			calc_latency;
	
struct work_struct	qos_work;
	
bool			is_suspending;
};


#define to_uart_omap_port(p) ((container_of((p), struct uart_omap_port, port)))


static struct uart_omap_port *ui[OMAP_MAX_HSUART_PORTS];

/* Forward declaration of functions */
static void serial_omap_mdr1_errataset(struct uart_omap_port *up, u8 mdr1);



static inline unsigned int serial_in(struct uart_omap_port *up, int offset)
{
	offset <<= up->port.regshift;
	return readw(up->port.membase + offset);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
36
100.00%
1
100.00%
Total
36
100.00%
1
100.00%



static inline void serial_out(struct uart_omap_port *up, int offset, int value)
{
	offset <<= up->port.regshift;
	writew(value, up->port.membase + offset);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
39
100.00%
1
100.00%
Total
39
100.00%
1
100.00%



static inline void serial_omap_clear_fifos(struct uart_omap_port *up)
{
	serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
	serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
		       UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
	serial_out(up, UART_FCR, 0);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
43
100.00%
1
100.00%
Total
43
100.00%
1
100.00%

#ifdef CONFIG_PM


static int serial_omap_get_context_loss_count(struct uart_omap_port *up)
{
	struct omap_uart_port_info *pdata = dev_get_platdata(up->dev);

	if (!pdata || !pdata->get_context_loss_count)
		return -EINVAL;

	return pdata->get_context_loss_count(up->dev);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
felipe balbi
felipe balbi
42
89.36%
2
50.00%
jingoo han
jingoo han
3
6.38%
1
25.00%
tony lindgren
tony lindgren
2
4.26%
1
25.00%
Total
47
100.00%
4
100.00%

/* REVISIT: Remove this when omap3 boots in device tree only mode */


static void serial_omap_enable_wakeup(struct uart_omap_port *up, bool enable)
{
	struct omap_uart_port_info *pdata = dev_get_platdata(up->dev);

	if (!pdata || !pdata->enable_wakeup)
		return;

	pdata->enable_wakeup(up->dev, enable);
}
Contributors
Person
Tokens
Prop
Commits
CommitProp
felipe balbi
felipe balbi
43
89.58%
3
60.00%
jingoo han
jingoo han
3
6.25%
1
20.00%
tony lindgren
tony lindgren
2
4.17%
1
20.00%
Total
48
100.00%
5
100.00%

#endif /* CONFIG_PM */

/*
 * Calculate the absolute difference between the desired and actual baud
 * rate for the given mode.
 */


static inline int calculate_baud_abs_diff(struct uart_port *port,
				unsigned int baud, unsigned int mode)
{
	unsigned int n = port->uartclk / (mode * baud);
	int abs_diff;

	if (n == 0)
		n = 1;

	abs_diff = baud - (port->uartclk / (mode * n));
	if (abs_diff < 0)
		abs_diff = -abs_diff;

	return abs_diff;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
alexey pelykh
alexey pelykh
45
58.44%
1
33.33%
frans klaver
frans klaver
32
41.56%
2
66.67%
Total
77
100.00%
3
100.00%

/*
 * serial_omap_baud_is_mode16 - check if baud rate is MODE16X
 * @port: uart port info
 * @baud: baudrate for which mode needs to be determined
 *
 * Returns true if baud rate is MODE16X and false if MODE13X
 * Original table in OMAP TRM named "UART Mode Baud Rates, Divisor Values,
 * and Error Rates" determines modes not for all common baud rates.
 * E.g. for 1000000 baud rate mode must be 16x, but according to that
 * table it's determined as 13x.
 */

static bool

serial_omap_baud_is_mode16(struct uart_port *port, unsigned int baud)
{
	int abs_diff_13 = calculate_baud_abs_diff(port, baud, 13);
	int abs_diff_16 = calculate_baud_abs_diff(port, baud, 16);

	return (abs_diff_13 >= abs_diff_16);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
frans klaver
frans klaver
41
89.13%
1
33.33%
alexey pelykh
alexey pelykh
5
10.87%
2
66.67%
Total
46
100.00%
3
100.00%

/*
 * serial_omap_get_divisor - calculate divisor value
 * @port: uart port info
 * @baud: baudrate for which divisor needs to be calculated.
 */

static unsigned int

serial_omap_get_divisor(struct uart_port *port, unsigned int baud)
{
	unsigned int mode;

	if (!serial_omap_baud_is_mode16(port, baud))
		mode = 13;
	else
		mode = 16;
	return port->uartclk/(mode * baud);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
39
78.00%
1
33.33%
alexey pelykh
alexey pelykh
11
22.00%
2
66.67%
Total
50
100.00%
3
100.00%



static void serial_omap_enable_ms(struct uart_port *port)
{
	struct uart_omap_port *up = to_uart_omap_port(port);

	dev_dbg(up->port.dev, "serial_omap_enable_ms+%d\n", up->port.line);

	pm_runtime_get_sync(up->dev);
	up->ier |= UART_IER_MSI;
	serial_out(up, UART_IER, up->ier);
	pm_runtime_mark_last_busy(up->dev);
	pm_runtime_put_autosuspend(up->dev);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
62
81.58%
2
40.00%
felipe balbi
felipe balbi
11
14.47%
2
40.00%
rajendra nayak
rajendra nayak
3
3.95%
1
20.00%
Total
76
100.00%
5
100.00%



static void serial_omap_stop_tx(struct uart_port *port)
{
	struct uart_omap_port *up = to_uart_omap_port(port);
	int res;

	pm_runtime_get_sync(up->dev);

	/* Handle RS-485 */
	if (port->rs485.flags & SER_RS485_ENABLED) {
		if (up->scr & OMAP_UART_SCR_TX_EMPTY) {
			/* THR interrupt is fired when both TX FIFO and TX
                         * shift register are empty. This means there's nothing
                         * left to transmit now, so make sure the THR interrupt
                         * is fired when TX FIFO is below the trigger level,
                         * disable THR interrupts and toggle the RS-485 GPIO
                         * data direction pin if needed.
                         */
			up->scr &= ~OMAP_UART_SCR_TX_EMPTY;
			serial_out(up, UART_OMAP_SCR, up->scr);
			res = (port->rs485.flags & SER_RS485_RTS_AFTER_SEND) ?
				1 : 0;
			if (gpio_get_value(up->rts_gpio) != res) {
				if (port->rs485.delay_rts_after_send > 0)
					mdelay(
					port->rs485.delay_rts_after_send);
				gpio_set_value(up->rts_gpio, res);
			}
		} else {
			/* We're asked to stop, but there's still stuff in the
                         * UART FIFO, so make sure the THR interrupt is fired
                         * when both TX FIFO and TX shift register are empty.
                         * The next THR interrupt (if no transmission is started
                         * in the meantime) will indicate the end of a
                         * transmission. Therefore we _don't_ disable THR
                         * interrupts in this situation.
                         */
			up->scr |= OMAP_UART_SCR_TX_EMPTY;
			serial_out(up, UART_OMAP_SCR, up->scr);
			return;
		}
	}

	if (up->ier & UART_IER_THRI) {
		up->ier &= ~UART_IER_THRI;
		serial_out(up, UART_IER, up->ier);
	}

	if ((port->rs485.flags & SER_RS485_ENABLED) &&
	    !(port->rs485.flags & SER_RS485_RX_DURING_TX)) {
		/*
                 * Empty the RX FIFO, we are not interested in anything
                 * received during the half-duplex transmission.
                 */
		serial_out(up, UART_FCR, up->fcr | UART_FCR_CLEAR_RCVR);
		/* Re-enable RX interrupts */
		up->ier |= UART_IER_RLSI | UART_IER_RDI;
		up->port.read_status_mask |= UART_LSR_DR;
		serial_out(up, UART_IER, up->ier);
	}

	pm_runtime_mark_last_busy(up->dev);
	pm_runtime_put_autosuspend(up->dev);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
mark jackson
mark jackson
115
44.06%
1
12.50%
govindraj raja
govindraj raja
67
25.67%
2
25.00%
philippe proulx
philippe proulx
46
17.62%
1
12.50%
dimitris lampridis
dimitris lampridis
24
9.20%
2
25.00%
ricardo ribalda
ricardo ribalda
6
2.30%
1
12.50%
felipe balbi
felipe balbi
3
1.15%
1
12.50%
Total
261
100.00%
8
100.00%



static void serial_omap_stop_rx(struct uart_port *port)
{
	struct uart_omap_port *up = to_uart_omap_port(port);

	pm_runtime_get_sync(up->dev);
	up->ier &= ~(UART_IER_RLSI | UART_IER_RDI);
	up->port.read_status_mask &= ~UART_LSR_DR;
	serial_out(up, UART_IER, up->ier);
	pm_runtime_mark_last_busy(up->dev);
	pm_runtime_put_autosuspend(up->dev);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
66
90.41%
2
50.00%
dimitris lampridis
dimitris lampridis
4
5.48%
1
25.00%
felipe balbi
felipe balbi
3
4.11%
1
25.00%
Total
73
100.00%
4
100.00%



static void transmit_chars(struct uart_omap_port *up, unsigned int lsr)
{
	struct circ_buf *xmit = &up->port.state->xmit;
	int count;

	if (up->port.x_char) {
		serial_out(up, UART_TX, up->port.x_char);
		up->port.icount.tx++;
		up->port.x_char = 0;
		return;
	}
	if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) {
		serial_omap_stop_tx(&up->port);
		return;
	}
	count = up->port.fifosize / 4;
	do {
		serial_out(up, UART_TX, xmit->buf[xmit->tail]);
		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
		up->port.icount.tx++;
		if (uart_circ_empty(xmit))
			break;
	} while (--count > 0);

	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
		uart_write_wakeup(&up->port);

	if (uart_circ_empty(xmit))
		serial_omap_stop_tx(&up->port);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
194
95.57%
1
25.00%
greg kroah-hartman
greg kroah-hartman
5
2.46%
2
50.00%
felipe balbi
felipe balbi
4
1.97%
1
25.00%
Total
203
100.00%
4
100.00%



static inline void serial_omap_enable_ier_thri(struct uart_omap_port *up)
{
	if (!(up->ier & UART_IER_THRI)) {
		up->ier |= UART_IER_THRI;
		serial_out(up, UART_IER, up->ier);
	}
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
42
100.00%
1
100.00%
Total
42
100.00%
1
100.00%



static void serial_omap_start_tx(struct uart_port *port)
{
	struct uart_omap_port *up = to_uart_omap_port(port);
	int res;

	pm_runtime_get_sync(up->dev);

	/* Handle RS-485 */
	if (port->rs485.flags & SER_RS485_ENABLED) {
		/* Fire THR interrupts when FIFO is below trigger level */
		up->scr &= ~OMAP_UART_SCR_TX_EMPTY;
		serial_out(up, UART_OMAP_SCR, up->scr);

		/* if rts not already enabled */
		res = (port->rs485.flags & SER_RS485_RTS_ON_SEND) ? 1 : 0;
		if (gpio_get_value(up->rts_gpio) != res) {
			gpio_set_value(up->rts_gpio, res);
			if (port->rs485.delay_rts_before_send > 0)
				mdelay(port->rs485.delay_rts_before_send);
		}
	}

	if ((port->rs485.flags & SER_RS485_ENABLED) &&
	    !(port->rs485.flags & SER_RS485_RX_DURING_TX))
		serial_omap_stop_rx(port);

	serial_omap_enable_ier_thri(up);
	pm_runtime_mark_last_busy(up->dev);
	pm_runtime_put_autosuspend(up->dev);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
mark jackson
mark jackson
95
56.55%
1
16.67%
govindraj raja
govindraj raja
44
26.19%
2
33.33%
philippe proulx
philippe proulx
20
11.90%
1
16.67%
ricardo ribalda
ricardo ribalda
6
3.57%
1
16.67%
felipe balbi
felipe balbi
3
1.79%
1
16.67%
Total
168
100.00%
6
100.00%



static void serial_omap_throttle(struct uart_port *port)
{
	struct uart_omap_port *up = to_uart_omap_port(port);
	unsigned long flags;

	pm_runtime_get_sync(up->dev);
	spin_lock_irqsave(&up->port.lock, flags);
	up->ier &= ~(UART_IER_RLSI | UART_IER_RDI);
	serial_out(up, UART_IER, up->ier);
	spin_unlock_irqrestore(&up->port.lock, flags);
	pm_runtime_mark_last_busy(up->dev);
	pm_runtime_put_autosuspend(up->dev);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
russell king
russell king
56
60.87%
1
25.00%
felipe balbi
felipe balbi
30
32.61%
2
50.00%
govindraj raja
govindraj raja
6
6.52%
1
25.00%
Total
92
100.00%
4
100.00%



static void serial_omap_unthrottle(struct uart_port *port)
{
	struct uart_omap_port *up = to_uart_omap_port(port);
	unsigned long flags;

	pm_runtime_get_sync(up->dev);
	spin_lock_irqsave(&up->port.lock, flags);
	up->ier |= UART_IER_RLSI | UART_IER_RDI;
	serial_out(up, UART_IER, up->ier);
	spin_unlock_irqrestore(&up->port.lock, flags);
	pm_runtime_mark_last_busy(up->dev);
	pm_runtime_put_autosuspend(up->dev);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
russell king
russell king
89
100.00%
1
100.00%
Total
89
100.00%
1
100.00%



static unsigned int check_modem_status(struct uart_omap_port *up)
{
	unsigned int status;

	status = serial_in(up, UART_MSR);
	status |= up->msr_saved_flags;
	up->msr_saved_flags = 0;
	if ((status & UART_MSR_ANY_DELTA) == 0)
		return status;

	if (status & UART_MSR_ANY_DELTA && up->ier & UART_IER_MSI &&
	    up->port.state != NULL) {
		if (status & UART_MSR_TERI)
			up->port.icount.rng++;
		if (status & UART_MSR_DDSR)
			up->port.icount.dsr++;
		if (status & UART_MSR_DDCD)
			uart_handle_dcd_change
				(&up->port, status & UART_MSR_DCD);
		if (status & UART_MSR_DCTS)
			uart_handle_cts_change
				(&up->port, status & UART_MSR_CTS);
		wake_up_interruptible(&up->port.state->port.delta_msr_wait);
	}

	return status;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
felipe balbi
felipe balbi
128
82.58%
2
66.67%
govindraj raja
govindraj raja
27
17.42%
1
33.33%
Total
155
100.00%
3
100.00%



static void serial_omap_rlsi(struct uart_omap_port *up, unsigned int lsr)
{
	unsigned int flag;
	unsigned char ch = 0;

	if (likely(lsr & UART_LSR_DR))
		ch = serial_in(up, UART_RX);

	up->port.icount.rx++;
	flag = TTY_NORMAL;

	if (lsr & UART_LSR_BI) {
		flag = TTY_BREAK;
		lsr &= ~(UART_LSR_FE | UART_LSR_PE);
		up->port.icount.brk++;
		/*
                 * We do the SysRQ and SAK checking
                 * here because otherwise the break
                 * may get masked by ignore_status_mask
                 * or read_status_mask.
                 */
		if (uart_handle_break(&up->port))
			return;

	}

	if (lsr & UART_LSR_PE) {
		flag = TTY_PARITY;
		up->port.icount.parity++;
	}

	if (lsr & UART_LSR_FE) {
		flag = TTY_FRAME;
		up->port.icount.frame++;
	}

	if (lsr & UART_LSR_OE)
		up->port.icount.overrun++;

#ifdef CONFIG_SERIAL_OMAP_CONSOLE
	if (up->port.line == up->port.cons->index) {
		/* Recover the break flag from console xmit */
		lsr |= up->lsr_break_flag;
	}
#endif
	uart_insert_char(&up->port, lsr, UART_LSR_OE, 0, flag);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
felipe balbi
felipe balbi
137
68.16%
1
33.33%
govindraj raja
govindraj raja
40
19.90%
1
33.33%
shubhrajyoti datta
shubhrajyoti datta
24
11.94%
1
33.33%
Total
201
100.00%
3
100.00%



static void serial_omap_rdi(struct uart_omap_port *up, unsigned int lsr)
{
	unsigned char ch = 0;
	unsigned int flag;

	if (!(lsr & UART_LSR_DR))
		return;

	ch = serial_in(up, UART_RX);
	flag = TTY_NORMAL;
	up->port.icount.rx++;

	if (uart_handle_sysrq_char(&up->port, ch))
		return;

	uart_insert_char(&up->port, lsr, UART_LSR_OE, ch, flag);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
felipe balbi
felipe balbi
67
77.91%
1
50.00%
govindraj raja
govindraj raja
19
22.09%
1
50.00%
Total
86
100.00%
2
100.00%

/**
 * serial_omap_irq() - This handles the interrupt from one port
 * @irq: uart port irq number
 * @dev_id: uart port info
 */


static irqreturn_t serial_omap_irq(int irq, void *dev_id)
{
	struct uart_omap_port *up = dev_id;
	unsigned int iir, lsr;
	unsigned int type;
	irqreturn_t ret = IRQ_NONE;
	int max_count = 256;

	spin_lock(&up->port.lock);
	pm_runtime_get_sync(up->dev);

	do {
		iir = serial_in(up, UART_IIR);
		if (iir & UART_IIR_NO_INT)
			break;

		ret = IRQ_HANDLED;
		lsr = serial_in(up, UART_LSR);

		/* extract IRQ type from IIR register */
		type = iir & 0x3e;

		switch (type) {
		case UART_IIR_MSI:
			check_modem_status(up);
			break;
		case UART_IIR_THRI:
			transmit_chars(up, lsr);
			break;
		case UART_IIR_RX_TIMEOUT:
			/* FALLTHROUGH */
		case UART_IIR_RDI:
			serial_omap_rdi(up, lsr);
			break;
		case UART_IIR_RLSI:
			serial_omap_rlsi(up, lsr);
			break;
		case UART_IIR_CTS_RTS_DSR:
			/* simply try again */
			break;
		case UART_IIR_XOFF:
			/* FALLTHROUGH */
		default:
			break;
		}
	} while (!(iir & UART_IIR_NO_INT) && max_count--);

	spin_unlock(&up->port.lock);

	tty_flip_buffer_push(&up->port.state->port);

	pm_runtime_mark_last_busy(up->dev);
	pm_runtime_put_autosuspend(up->dev);
	up->port_activity = jiffies;

	return ret;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
101
46.54%
2
25.00%
felipe balbi
felipe balbi
98
45.16%
4
50.00%
greg kroah-hartman
greg kroah-hartman
10
4.61%
1
12.50%
jiri slaby
jiri slaby
8
3.69%
1
12.50%
Total
217
100.00%
8
100.00%



static unsigned int serial_omap_tx_empty(struct uart_port *port)
{
	struct uart_omap_port *up = to_uart_omap_port(port);
	unsigned long flags = 0;
	unsigned int ret = 0;

	pm_runtime_get_sync(up->dev);
	dev_dbg(up->port.dev, "serial_omap_tx_empty+%d\n", up->port.line);
	spin_lock_irqsave(&up->port.lock, flags);
	ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
	spin_unlock_irqrestore(&up->port.lock, flags);
	pm_runtime_mark_last_busy(up->dev);
	pm_runtime_put_autosuspend(up->dev);
	return ret;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
100
87.72%
2
40.00%
felipe balbi
felipe balbi
11
9.65%
2
40.00%
rajendra nayak
rajendra nayak
3
2.63%
1
20.00%
Total
114
100.00%
5
100.00%



static unsigned int serial_omap_get_mctrl(struct uart_port *port)
{
	struct uart_omap_port *up = to_uart_omap_port(port);
	unsigned int status;
	unsigned int ret = 0;

	pm_runtime_get_sync(up->dev);
	status = check_modem_status(up);
	pm_runtime_mark_last_busy(up->dev);
	pm_runtime_put_autosuspend(up->dev);

	dev_dbg(up->port.dev, "serial_omap_get_mctrl+%d\n", up->port.line);

	if (status & UART_MSR_DCD)
		ret |= TIOCM_CAR;
	if (status & UART_MSR_RI)
		ret |= TIOCM_RNG;
	if (status & UART_MSR_DSR)
		ret |= TIOCM_DSR;
	if (status & UART_MSR_CTS)
		ret |= TIOCM_CTS;
	return ret;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
105
87.50%
2
33.33%
felipe balbi
felipe balbi
11
9.17%
2
33.33%
rajendra nayak
rajendra nayak
3
2.50%
1
16.67%
shubhrajyoti datta
shubhrajyoti datta
1
0.83%
1
16.67%
Total
120
100.00%
6
100.00%



static void serial_omap_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
	struct uart_omap_port *up = to_uart_omap_port(port);
	unsigned char mcr = 0, old_mcr, lcr;

	dev_dbg(up->port.dev, "serial_omap_set_mctrl+%d\n", up->port.line);
	if (mctrl & TIOCM_RTS)
		mcr |= UART_MCR_RTS;
	if (mctrl & TIOCM_DTR)
		mcr |= UART_MCR_DTR;
	if (mctrl & TIOCM_OUT1)
		mcr |= UART_MCR_OUT1;
	if (mctrl & TIOCM_OUT2)
		mcr |= UART_MCR_OUT2;
	if (mctrl & TIOCM_LOOP)
		mcr |= UART_MCR_LOOP;

	pm_runtime_get_sync(up->dev);
	old_mcr = serial_in(up, UART_MCR);
	old_mcr &= ~(UART_MCR_LOOP | UART_MCR_OUT2 | UART_MCR_OUT1 |
		     UART_MCR_DTR | UART_MCR_RTS);
	up->mcr = old_mcr | mcr;
	serial_out(up, UART_MCR, up->mcr);

	/* Turn off autoRTS if RTS is lowered; restore autoRTS if RTS raised */
	lcr = serial_in(up, UART_LCR);
	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
	if ((mctrl & TIOCM_RTS) && (port->status & UPSTAT_AUTORTS))
		up->efr |= UART_EFR_RTS;
	else
		up->efr &= UART_EFR_RTS;
	serial_out(up, UART_EFR, up->efr);
	serial_out(up, UART_LCR, lcr);

	pm_runtime_mark_last_busy(up->dev);
	pm_runtime_put_autosuspend(up->dev);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
129
55.13%
3
37.50%
peter hurley
peter hurley
70
29.91%
1
12.50%
russell king
russell king
21
8.97%
1
12.50%
felipe balbi
felipe balbi
11
4.70%
2
25.00%
rajendra nayak
rajendra nayak
3
1.28%
1
12.50%
Total
234
100.00%
8
100.00%



static void serial_omap_break_ctl(struct uart_port *port, int break_state)
{
	struct uart_omap_port *up = to_uart_omap_port(port);
	unsigned long flags = 0;

	dev_dbg(up->port.dev, "serial_omap_break_ctl+%d\n", up->port.line);
	pm_runtime_get_sync(up->dev);
	spin_lock_irqsave(&up->port.lock, flags);
	if (break_state == -1)
		up->lcr |= UART_LCR_SBC;
	else
		up->lcr &= ~UART_LCR_SBC;
	serial_out(up, UART_LCR, up->lcr);
	spin_unlock_irqrestore(&up->port.lock, flags);
	pm_runtime_mark_last_busy(up->dev);
	pm_runtime_put_autosuspend(up->dev);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
110
88.71%
2
40.00%
felipe balbi
felipe balbi
11
8.87%
2
40.00%
rajendra nayak
rajendra nayak
3
2.42%
1
20.00%
Total
124
100.00%
5
100.00%



static int serial_omap_startup(struct uart_port *port)
{
	struct uart_omap_port *up = to_uart_omap_port(port);
	unsigned long flags = 0;
	int retval;

	/*
         * Allocate the IRQ
         */
	retval = request_irq(up->port.irq, serial_omap_irq, up->port.irqflags,
				up->name, up);
	if (retval)
		return retval;

	/* Optional wake-up IRQ */
	if (up->wakeirq) {
		retval = dev_pm_set_dedicated_wake_irq(up->dev, up->wakeirq);
		if (retval) {
			free_irq(up->port.irq, up);
			return retval;
		}
	}

	dev_dbg(up->port.dev, "serial_omap_startup+%d\n", up->port.line);

	pm_runtime_get_sync(up->dev);
	/*
         * Clear the FIFO buffers and disable them.
         * (they will be reenabled in set_termios())
         */
	serial_omap_clear_fifos(up);

	/*
         * Clear the interrupt registers.
         */
	(void) serial_in(up, UART_LSR);
	if (serial_in(up, UART_LSR) & UART_LSR_DR)
		(void) serial_in(up, UART_RX);
	(void) serial_in(up, UART_IIR);
	(void) serial_in(up, UART_MSR);

	/*
         * Now, initialize the UART
         */
	serial_out(up, UART_LCR, UART_LCR_WLEN8);
	spin_lock_irqsave(&up->port.lock, flags);
	/*
         * Most PC uarts need OUT2 raised to enable interrupts.
         */
	up->port.mctrl |= TIOCM_OUT2;
	serial_omap_set_mctrl(&up->port, up->port.mctrl);
	spin_unlock_irqrestore(&up->port.lock, flags);

	up->msr_saved_flags = 0;
	/*
         * Finally, enable interrupts. Note: Modem status interrupts
         * are set via set_termios(), which will be occurring imminently
         * anyway, so we don't enable them here.
         */
	up->ier = UART_IER_RLSI | UART_IER_RDI;
	serial_out(up, UART_IER, up->ier);

	/* Enable module level wake up */
	up->wer = OMAP_UART_WER_MOD_WKUP;
	if (up->features & OMAP_UART_WER_HAS_TX_WAKEUP)
		up->wer |= OMAP_UART_TX_WAKEUP_EN;

	serial_out(up, UART_OMAP_WER, up->wer);

	pm_runtime_mark_last_busy(up->dev);
	pm_runtime_put_autosuspend(up->dev);
	up->port_activity = jiffies;
	return 0;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
268
82.46%
3
37.50%
tony lindgren
tony lindgren
42
12.92%
2
25.00%
jarkko nikula
jarkko nikula
9
2.77%
1
12.50%
rajendra nayak
rajendra nayak
3
0.92%
1
12.50%
felipe balbi
felipe balbi
3
0.92%
1
12.50%
Total
325
100.00%
8
100.00%



static void serial_omap_shutdown(struct uart_port *port)
{
	struct uart_omap_port *up = to_uart_omap_port(port);
	unsigned long flags = 0;

	dev_dbg(up->port.dev, "serial_omap_shutdown+%d\n", up->port.line);

	pm_runtime_get_sync(up->dev);
	/*
         * Disable interrupts from this port
         */
	up->ier = 0;
	serial_out(up, UART_IER, 0);

	spin_lock_irqsave(&up->port.lock, flags);
	up->port.mctrl &= ~TIOCM_OUT2;
	serial_omap_set_mctrl(&up->port, up->port.mctrl);
	spin_unlock_irqrestore(&up->port.lock, flags);

	/*
         * Disable break condition and FIFOs
         */
	serial_out(up, UART_LCR, serial_in(up, UART_LCR) & ~UART_LCR_SBC);
	serial_omap_clear_fifos(up);

	/*
         * Read data port to reset things, and then free the irq
         */
	if (serial_in(up, UART_LSR) & UART_LSR_DR)
		(void) serial_in(up, UART_RX);

	pm_runtime_mark_last_busy(up->dev);
	pm_runtime_put_autosuspend(up->dev);
	free_irq(up->port.irq, up);
	dev_pm_clear_wake_irq(up->dev);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
170
89.01%
2
28.57%
felipe balbi
felipe balbi
11
5.76%
2
28.57%
tony lindgren
tony lindgren
7
3.66%
2
28.57%
rajendra nayak
rajendra nayak
3
1.57%
1
14.29%
Total
191
100.00%
7
100.00%



static void serial_omap_uart_qos_work(struct work_struct *work)
{
	struct uart_omap_port *up = container_of(work, struct uart_omap_port,
						qos_work);

	pm_qos_update_request(&up->pm_qos_request, up->latency);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
38
100.00%
2
100.00%
Total
38
100.00%
2
100.00%


static void

serial_omap_set_termios(struct uart_port *port, struct ktermios *termios,
			struct ktermios *old)
{
	struct uart_omap_port *up = to_uart_omap_port(port);
	unsigned char cval = 0;
	unsigned long flags = 0;
	unsigned int baud, quot;

	switch (termios->c_cflag & CSIZE) {
	case CS5:
		cval = UART_LCR_WLEN5;
		break;
	case CS6:
		cval = UART_LCR_WLEN6;
		break;
	case CS7:
		cval = UART_LCR_WLEN7;
		break;
	default:
	case CS8:
		cval = UART_LCR_WLEN8;
		break;
	}

	if (termios->c_cflag & CSTOPB)
		cval |= UART_LCR_STOP;
	if (termios->c_cflag & PARENB)
		cval |= UART_LCR_PARITY;
	if (!(termios->c_cflag & PARODD))
		cval |= UART_LCR_EPAR;
	if (termios->c_cflag & CMSPAR)
		cval |= UART_LCR_SPAR;

	/*
         * Ask the core to calculate the divisor for us.
         */

	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/13);
	quot = serial_omap_get_divisor(port, baud);

	/* calculate wakeup latency constraint */
	up->calc_latency = (USEC_PER_SEC * up->port.fifosize) / (baud / 8);
	up->latency = up->calc_latency;
	schedule_work(&up->qos_work);

	up->dll = quot & 0xff;
	up->dlh = quot >> 8;
	up->mdr1 = UART_OMAP_MDR1_DISABLE;

	up->fcr = UART_FCR_R_TRIG_01 | UART_FCR_T_TRIG_01 |
			UART_FCR_ENABLE_FIFO;

	/*
         * Ok, we're now changing the port state. Do it with
         * interrupts disabled.
         */
	pm_runtime_get_sync(up->dev);
	spin_lock_irqsave(&up->port.lock, flags);

	/*
         * Update the per-port timeout.
         */
	uart_update_timeout(port, termios->c_cflag, baud);

	up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
	if (termios->c_iflag & INPCK)
		up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
	if (termios->c_iflag & (BRKINT | PARMRK))
		up->port.read_status_mask |= UART_LSR_BI;

	/*
         * Characters to ignore
         */
	up->port.ignore_status_mask = 0;
	if (termios->c_iflag & IGNPAR)
		up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
	if (termios->c_iflag & IGNBRK) {
		up->port.ignore_status_mask |= UART_LSR_BI;
		/*
                 * If we're ignoring parity and break indicators,
                 * ignore overruns too (for real raw support).
                 */
		if (termios->c_iflag & IGNPAR)
			up->port.ignore_status_mask |= UART_LSR_OE;
	}

	/*
         * ignore all characters if CREAD is not set
         */
	if ((termios->c_cflag & CREAD) == 0)
		up->port.ignore_status_mask |= UART_LSR_DR;

	/*
         * Modem status interrupts
         */
	up->ier &= ~UART_IER_MSI;
	if (UART_ENABLE_MS(&up->port, termios->c_cflag))
		up->ier |= UART_IER_MSI;
	serial_out(up, UART_IER, up->ier);
	serial_out(up, UART_LCR, cval);		/* reset DLAB */
	up->lcr = cval;
	up->scr = 0;

	/* FIFOs and DMA Settings */

	/* FCR can be changed only when the
         * baud clock is not running
         * DLL_REG and DLH_REG set to 0.
         */
	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
	serial_out(up, UART_DLL, 0);
	serial_out(up, UART_DLM, 0);
	serial_out(up, UART_LCR, 0);

	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);

	up->efr = serial_in(up, UART_EFR) & ~UART_EFR_ECB;
	up->efr &= ~UART_EFR_SCD;
	serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);

	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
	up->mcr = serial_in(up, UART_MCR) & ~UART_MCR_TCRTLR;
	serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR);
	/* FIFO ENABLE, DMA MODE */

	up->scr |= OMAP_UART_SCR_RX_TRIG_GRANU1_MASK;
	/*
         * NOTE: Setting OMAP_UART_SCR_RX_TRIG_GRANU1_MASK
         * sets Enables the granularity of 1 for TRIGGER RX
         * level. Along with setting RX FIFO trigger level
         * to 1 (as noted below, 16 characters) and TLR[3:0]
         * to zero this will result RX FIFO threshold level
         * to 1 character, instead of 16 as noted in comment
         * below.
         */

	/* Set receive FIFO threshold to 16 characters and
         * transmit FIFO threshold to 32 spaces
         */
	up->fcr &= ~OMAP_UART_FCR_RX_FIFO_TRIG_MASK;
	up->fcr &= ~OMAP_UART_FCR_TX_FIFO_TRIG_MASK;
	up->fcr |= UART_FCR6_R_TRIGGER_16 | UART_FCR6_T_TRIGGER_24 |
		UART_FCR_ENABLE_FIFO;

	serial_out(up, UART_FCR, up->fcr);
	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);

	serial_out(up, UART_OMAP_SCR, up->scr);

	/* Reset UART_MCR_TCRTLR: this must be done with the EFR_ECB bit set */
	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
	serial_out(up, UART_MCR, up->mcr);
	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
	serial_out(up, UART_EFR, up->efr);
	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);

	/* Protocol, Baud Rate, and Interrupt Settings */

	if (up->errata & UART_ERRATA_i202_MDR1_ACCESS)
		serial_omap_mdr1_errataset(up, up->mdr1);
	else
		serial_out(up, UART_OMAP_MDR1, up->mdr1);

	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
	serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);

	serial_out(up, UART_LCR, 0);
	serial_out(up, UART_IER, 0);
	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);

	serial_out(up, UART_DLL, up->dll);	/* LS of divisor */
	serial_out(up, UART_DLM, up->dlh);	/* MS of divisor */

	serial_out(up, UART_LCR, 0);
	serial_out(up, UART_IER, up->ier);
	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);

	serial_out(up, UART_EFR, up->efr);
	serial_out(up, UART_LCR, cval);

	if (!serial_omap_baud_is_mode16(port, baud))
		up->mdr1 = UART_OMAP_MDR1_13X_MODE;
	else
		up->mdr1 = UART_OMAP_MDR1_16X_MODE;

	if (up->errata & UART_ERRATA_i202_MDR1_ACCESS)
		serial_omap_mdr1_errataset(up, up->mdr1);
	else
		serial_out(up, UART_OMAP_MDR1, up->mdr1);

	/* Configure flow control */
	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);

	/* XON1/XOFF1 accessible mode B, TCRTLR=0, ECB=0 */
	serial_out(up, UART_XON1, termios->c_cc[VSTART]);
	serial_out(up, UART_XOFF1, termios->c_cc[VSTOP]);

	/* Enable access to TCR/TLR */
	serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
	serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR);

	serial_out(up, UART_TI752_TCR, OMAP_UART_TCR_TRIG);

	up->port.status &= ~(UPSTAT_AUTOCTS | UPSTAT_AUTORTS | UPSTAT_AUTOXOFF);

	if (termios->c_cflag & CRTSCTS && up->port.flags & UPF_HARD_FLOW) {
		/* Enable AUTOCTS (autoRTS is enabled when RTS is raised) */
		up->port.status |= UPSTAT_AUTOCTS | UPSTAT_AUTORTS;
		up->efr |= UART_EFR_CTS;
	} else {
		/* Disable AUTORTS and AUTOCTS */
		up->efr &= ~(UART_EFR_CTS | UART_EFR_RTS);
	}

	if (up->port.flags & UPF_SOFT_FLOW) {
		/* clear SW control mode bits */
		up->efr &= OMAP_UART_SW_CLR;

		/*
                 * IXON Flag:
                 * Enable XON/XOFF flow control on input.
                 * Receiver compares XON1, XOFF1.
                 */
		if (termios->c_iflag & IXON)
			up->efr |= OMAP_UART_SW_RX;

		/*
                 * IXOFF Flag:
                 * Enable XON/XOFF flow control on output.
                 * Transmit XON1, XOFF1
                 */
		if (termios->c_iflag & IXOFF) {
			up->port.status |= UPSTAT_AUTOXOFF;
			up->efr |= OMAP_UART_SW_TX;
		}

		/*
                 * IXANY Flag:
                 * Enable any character to restart output.
                 * Operation resumes after receiving any
                 * character after recognition of the XOFF character
                 */
		if (termios->c_iflag & IXANY)
			up->mcr |= UART_MCR_XONANY;
		else
			up->mcr &= ~UART_MCR_XONANY;
	}
	serial_out(up, UART_MCR, up->mcr);
	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
	serial_out(up, UART_EFR, up->efr);
	serial_out(up, UART_LCR, up->lcr);

	serial_omap_set_mctrl(&up->port, up->port.mctrl);

	spin_unlock_irqrestore(&up->port.lock, flags);
	pm_runtime_mark_last_busy(up->dev);
	pm_runtime_put_autosuspend(up->dev);
	dev_dbg(up->port.dev, "serial_omap_set_termios+%d\n", up->port.line);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
931
75.57%
6
20.69%
russell king
russell king
167
13.56%
8
27.59%
paul walmsley
paul walmsley
38
3.08%
2
6.90%
peter hurley
peter hurley
36
2.92%
2
6.90%
felipe balbi
felipe balbi
23
1.87%
3
10.34%
alexey pelykh
alexey pelykh
14
1.14%
3
10.34%
enric balletbo i serra
enric balletbo i serra
12
0.97%
1
3.45%
andrei emeltchenko
andrei emeltchenko
7
0.57%
2
6.90%
rajendra nayak
rajendra nayak
3
0.24%
1
3.45%
philippe proulx
philippe proulx
1
0.08%
1
3.45%
Total
1232
100.00%
29
100.00%


static void

serial_omap_pm(struct uart_port *port, unsigned int state,
	       unsigned int oldstate)
{
	struct uart_omap_port *up = to_uart_omap_port(port);
	unsigned char efr;

	dev_dbg(up->port.dev, "serial_omap_pm+%d\n", up->port.line);

	pm_runtime_get_sync(up->dev);
	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
	efr = serial_in(up, UART_EFR);
	serial_out(up, UART_EFR, efr | UART_EFR_ECB);
	serial_out(up, UART_LCR, 0);

	serial_out(up, UART_IER, (state != 0) ? UART_IERX_SLEEP : 0);
	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
	serial_out(up, UART_EFR, efr);
	serial_out(up, UART_LCR, 0);

	pm_runtime_mark_last_busy(up->dev);
	pm_runtime_put_autosuspend(up->dev);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
137
89.54%
2
33.33%
felipe balbi
felipe balbi
11
7.19%
2
33.33%
rajendra nayak
rajendra nayak
3
1.96%
1
16.67%
andrei emeltchenko
andrei emeltchenko
2
1.31%
1
16.67%
Total
153
100.00%
6
100.00%



static void serial_omap_release_port(struct uart_port *port)
{
	dev_dbg(port->dev, "serial_omap_release_port+\n");
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
20
100.00%
1
100.00%
Total
20
100.00%
1
100.00%



static int serial_omap_request_port(struct uart_port *port)
{
	dev_dbg(port->dev, "serial_omap_request_port+\n");
	return 0;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
23
100.00%
1
100.00%
Total
23
100.00%
1
100.00%



static void serial_omap_config_port(struct uart_port *port, int flags)
{
	struct uart_omap_port *up = to_uart_omap_port(port);

	dev_dbg(up->port.dev, "serial_omap_config_port+%d\n",
							up->port.line);
	up->port.type = PORT_OMAP;
	up->port.flags |= UPF_SOFT_FLOW | UPF_HARD_FLOW;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
43
72.88%
1
25.00%
russell king
russell king
10
16.95%
1
25.00%
rajendra nayak
rajendra nayak
3
5.08%
1
25.00%
felipe balbi
felipe balbi
3
5.08%
1
25.00%
Total
59
100.00%
4
100.00%


static int

serial_omap_verify_port(struct uart_port *port, struct serial_struct *ser)
{
	/* we don't want the core code to modify any port params */
	dev_dbg(port->dev, "serial_omap_verify_port+\n");
	return -EINVAL;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
30
100.00%
1
100.00%
Total
30
100.00%
1
100.00%


static const char *

serial_omap_type(struct uart_port *port)
{
	struct uart_omap_port *up = to_uart_omap_port(port);

	dev_dbg(up->port.dev, "serial_omap_type+%d\n", up->port.line);
	return up->name;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
39
86.67%
1
33.33%
felipe balbi
felipe balbi
3
6.67%
1
33.33%
rajendra nayak
rajendra nayak
3
6.67%
1
33.33%
Total
45
100.00%
3
100.00%


#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)



static void __maybe_unused wait_for_xmitr(struct uart_omap_port *up)
{
	unsigned int status, tmout = 10000;

	/* Wait up to 10ms for the character(s) to be sent. */
	do {
		status = serial_in(up, UART_LSR);

		if (status & UART_LSR_BI)
			up->lsr_break_flag = UART_LSR_BI;

		if (--tmout == 0)
			break;
		udelay(1);
	} while ((status & BOTH_EMPTY) != BOTH_EMPTY);

	/* Wait up to 1s for flow control if necessary */
	if (up->port.flags & UPF_CONS_FLOW) {
		tmout = 1000000;
		for (tmout = 1000000; tmout; tmout--) {
			unsigned int msr = serial_in(up, UART_MSR);

			up->msr_saved_flags |= msr & MSR_SAVE_FLAGS;
			if (msr & UART_MSR_CTS)
				break;

			udelay(1);
		}
	}
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
129
99.23%
1
50.00%
arnd bergmann
arnd bergmann
1
0.77%
1
50.00%
Total
130
100.00%
2
100.00%

#ifdef CONFIG_CONSOLE_POLL



static void serial_omap_poll_put_char(struct uart_port *port, unsigned char ch)
{
	struct uart_omap_port *up = to_uart_omap_port(port);

	pm_runtime_get_sync(up->dev);
	wait_for_xmitr(up);
	serial_out(up, UART_TX, ch);
	pm_runtime_mark_last_busy(up->dev);
	pm_runtime_put_autosuspend(up->dev);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
cosmin cojocar
cosmin cojocar
36
60.00%
1
25.00%
govindraj raja
govindraj raja
13
21.67%
1
25.00%
felipe balbi
felipe balbi
11
18.33%
2
50.00%
Total
60
100.00%
4
100.00%



static int serial_omap_poll_get_char(struct uart_port *port)
{
	struct uart_omap_port *up = to_uart_omap_port(port);
	unsigned int status;

	pm_runtime_get_sync(up->dev);
	status = serial_in(up, UART_LSR);
	if (!(status & UART_LSR_DR)) {
		status = NO_POLL_CHAR;
		goto out;
	}

	status = serial_in(up, UART_RX);

out:
	pm_runtime_mark_last_busy(up->dev);
	pm_runtime_put_autosuspend(up->dev);

	return status;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
cosmin cojocar
cosmin cojocar
44
50.57%
1
20.00%
govindraj raja
govindraj raja
22
25.29%
1
20.00%
felipe balbi
felipe balbi
21
24.14%
3
60.00%
Total
87
100.00%
5
100.00%

#endif /* CONFIG_CONSOLE_POLL */

#ifdef CONFIG_SERIAL_OMAP_CONSOLE


static struct uart_omap_port *serial_omap_console_ports[OMAP_MAX_HSUART_PORTS];


static struct uart_driver serial_omap_reg;



static void serial_omap_console_putchar(struct uart_port *port, int ch)
{
	struct uart_omap_port *up = to_uart_omap_port(port);

	wait_for_xmitr(up);
	serial_out(up, UART_TX, ch);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
35
92.11%
1
50.00%
felipe balbi
felipe balbi
3
7.89%
1
50.00%
Total
38
100.00%
2
100.00%


static void

serial_omap_console_write(struct console *co, const char *s,
		unsigned int count)
{
	struct uart_omap_port *up = serial_omap_console_ports[co->index];
	unsigned long flags;
	unsigned int ier;
	int locked = 1;

	pm_runtime_get_sync(up->dev);

	local_irq_save(flags);
	if (up->port.sysrq)
		locked = 0;
	else if (oops_in_progress)
		locked = spin_trylock(&up->port.lock);
	else
		spin_lock(&up->port.lock);

	/*
         * First save the IER then disable the interrupts
         */
	ier = serial_in(up, UART_IER);
	serial_out(up, UART_IER, 0);

	uart_console_write(&up->port, s, count, serial_omap_console_putchar);

	/*
         * Finally, wait for transmitter to become empty
         * and restore the IER
         */
	wait_for_xmitr(up);
	serial_out(up, UART_IER, ier);
	/*
         * The receive handling will happen properly because the
         * receive ready bit will still be set; it is not cleared
         * on read.  However, modem control will not, we must
         * call it if we have saved something in the saved flags
         * while processing with interrupts off.
         */
	if (up->msr_saved_flags)
		check_modem_status(up);

	pm_runtime_mark_last_busy(up->dev);
	pm_runtime_put_autosuspend(up->dev);
	if (locked)
		spin_unlock(&up->port.lock);
	local_irq_restore(flags);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
190
100.00%
2
100.00%
Total
190
100.00%
2
100.00%


static int __init

serial_omap_console_setup(struct console *co, char *options)
{
	struct uart_omap_port *up;
	int baud = 115200;
	int bits = 8;
	int parity = 'n';
	int flow = 'n';

	if (serial_omap_console_ports[co->index] == NULL)
		return -ENODEV;
	up = serial_omap_console_ports[co->index];

	if (options)
		uart_parse_options(options, &baud, &parity, &bits, &flow);

	return uart_set_options(&up->port, co, baud, parity, bits, flow);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
105
100.00%
1
100.00%
Total
105
100.00%
1
100.00%


static struct console serial_omap_console = {
	.name		= OMAP_SERIAL_NAME,
	.write		= serial_omap_console_write,
	.device		= uart_console_device,
	.setup		= serial_omap_console_setup,
	.flags		= CON_PRINTBUFFER,
	.index		= -1,
	.data		= &serial_omap_reg,
};



static void serial_omap_add_console_port(struct uart_omap_port *up)
{
	serial_omap_console_ports[up->port.line] = up;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
19
86.36%
1
50.00%
rajendra nayak
rajendra nayak
3
13.64%
1
50.00%
Total
22
100.00%
2
100.00%


#define OMAP_CONSOLE	(&serial_omap_console)

#else


#define OMAP_CONSOLE	NULL



static inline void serial_omap_add_console_port(struct uart_omap_port *up)
{}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
11
100.00%
1
100.00%
Total
11
100.00%
1
100.00%

#endif

/* Enable or disable the rs485 support */

static int

serial_omap_config_rs485(struct uart_port *port, struct serial_rs485 *rs485)
{
	struct uart_omap_port *up = to_uart_omap_port(port);
	unsigned int mode;
	int val;

	pm_runtime_get_sync(up->dev);

	/* Disable interrupts from this port */
	mode = up->ier;
	up->ier = 0;
	serial_out(up, UART_IER, 0);

	/* Clamp the delays to [0, 100ms] */
	rs485->delay_rts_before_send = min(rs485->delay_rts_before_send, 100U);
	rs485->delay_rts_after_send  = min(rs485->delay_rts_after_send, 100U);

	/* store new config */
	port->rs485 = *rs485;

	/*
         * Just as a precaution, only allow rs485
         * to be enabled if the gpio pin is valid
         */
	if (gpio_is_valid(up->rts_gpio)) {
		/* enable / disable rts */
		val = (port->rs485.flags & SER_RS485_ENABLED) ?
			SER_RS485_RTS_AFTER_SEND : SER_RS485_RTS_ON_SEND;
		val = (port->rs485.flags & val) ? 1 : 0;
		gpio_set_value(up->rts_gpio, val);
	} else
		port->rs485.flags &= ~SER_RS485_ENABLED;

	/* Enable interrupts */
	up->ier = mode;
	serial_out(up, UART_IER, up->ier);

	/* If RS-485 is disabled, make sure the THR interrupt is fired when
         * TX FIFO is below the trigger level.
         */
	if (!(port->rs485.flags & SER_RS485_ENABLED) &&
	    (up->scr & OMAP_UART_SCR_TX_EMPTY)) {
		up->scr &= ~OMAP_UART_SCR_TX_EMPTY;
		serial_out(up, UART_OMAP_SCR, up->scr);
	}

	pm_runtime_mark_last_busy(up->dev);
	pm_runtime_put_autosuspend(up->dev);

	return 0;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
mark jackson
mark jackson
159
66.81%
1
20.00%
philippe proulx
philippe proulx
41
17.23%
1
20.00%
peter hurley
peter hurley
29
12.18%
1
20.00%
ricardo ribalda
ricardo ribalda
6
2.52%
1
20.00%
govindraj raja
govindraj raja
3
1.26%
1
20.00%
Total
238
100.00%
5
100.00%


static struct uart_ops serial_omap_pops = {
	.tx_empty	= serial_omap_tx_empty,
	.set_mctrl	= serial_omap_set_mctrl,
	.get_mctrl	= serial_omap_get_mctrl,
	.stop_tx	= serial_omap_stop_tx,
	.start_tx	= serial_omap_start_tx,
	.throttle	= serial_omap_throttle,
	.unthrottle	= serial_omap_unthrottle,
	.stop_rx	= serial_omap_stop_rx,
	.enable_ms	= serial_omap_enable_ms,
	.break_ctl	= serial_omap_break_ctl,
	.startup	= serial_omap_startup,
	.shutdown	= serial_omap_shutdown,
	.set_termios	= serial_omap_set_termios,
	.pm		= serial_omap_pm,
	.type		= serial_omap_type,
	.release_port	= serial_omap_release_port,
	.request_port	= serial_omap_request_port,
	.config_port	= serial_omap_config_port,
	.verify_port	= serial_omap_verify_port,
#ifdef CONFIG_CONSOLE_POLL
	.poll_put_char  = serial_omap_poll_put_char,
	.poll_get_char  = serial_omap_poll_get_char,
#endif
};


static struct uart_driver serial_omap_reg = {
	.owner		= THIS_MODULE,
	.driver_name	= "OMAP-SERIAL",
	.dev_name	= OMAP_SERIAL_NAME,
	.nr		= OMAP_MAX_HSUART_PORTS,
	.cons		= OMAP_CONSOLE,
};

#ifdef CONFIG_PM_SLEEP


static int serial_omap_prepare(struct device *dev)
{
	struct uart_omap_port *up = dev_get_drvdata(dev);

	up->is_suspending = true;

	return 0;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
sourav poddar
sourav poddar
30
100.00%
1
100.00%
Total
30
100.00%
1
100.00%



static void serial_omap_complete(struct device *dev)
{
	struct uart_omap_port *up = dev_get_drvdata(dev);

	up->is_suspending = false;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
sourav poddar
sourav poddar
27
100.00%
1
100.00%
Total
27
100.00%
1
100.00%



static int serial_omap_suspend(struct device *dev)
{
	struct uart_omap_port *up = dev_get_drvdata(dev);

	uart_suspend_port(&serial_omap_reg, &up->port);
	flush_work(&up->qos_work);

	if (device_may_wakeup(dev))
		serial_omap_enable_wakeup(up, true);
	else
		serial_omap_enable_wakeup(up, false);

	return 0;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
felipe balbi
felipe balbi
25
38.46%
1
25.00%
tony lindgren
tony lindgren
22
33.85%
1
25.00%
govindraj raja
govindraj raja
17
26.15%
1
25.00%
tejun heo
tejun heo
1
1.54%
1
25.00%
Total
65
100.00%
4
100.00%



static int serial_omap_resume(struct device *dev)
{
	struct uart_omap_port *up = dev_get_drvdata(dev);

	if (device_may_wakeup(dev))
		serial_omap_enable_wakeup(up, false);

	uart_resume_port(&serial_omap_reg, &up->port);

	return 0;
}
Contributors
Person
Tokens
Prop
Commits
CommitProp
felipe balbi
felipe balbi
27
55.10%
1
33.33%
tony lindgren
tony lindgren
14
28.57%
1
33.33%
govindraj raja
govindraj raja
8
16.33%
1
33.33%
Total
49
100.00%
3
100.00%

#else

#define serial_omap_prepare NULL

#define serial_omap_complete NULL
#endif /* CONFIG_PM_SLEEP */



static void omap_serial_fill_features_erratas(struct uart_omap_port *up)
{
	u32 mvr, scheme;
	u16 revision, major, minor;

	mvr = readl(up->port.membase + (UART_OMAP_MVER << up->port.regshift));

	/* Check revision register scheme */
	scheme = mvr >> OMAP_UART_MVR_SCHEME_SHIFT;

	switch (scheme) {
	case 0: /* Legacy Scheme: OMAP2/3 */
		/* MINOR_REV[0:4], MAJOR_REV[4:7] */
		major = (mvr & OMAP_UART_LEGACY_MVR_MAJ_MASK) >>
					OMAP_UART_LEGACY_MVR_MAJ_SHIFT;
		minor = (mvr & OMAP_UART_LEGACY_MVR_MIN_MASK);
		break;
	case 1:
		/* New Scheme: OMAP4+ */
		/* MINOR_REV[0:5], MAJOR_REV[8:10] */
		major = (mvr & OMAP_UART_MVR_MAJ_MASK) >>
					OMAP_UART_MVR_MAJ_SHIFT;
		minor = (mvr & OMAP_UART_MVR_MIN_MASK);
		break;
	default:
		dev_warn(up->dev,
			"Unknown %s revision, defaulting to highest\n",
			up->name);
		/* highest possible revision */
		major = 0xff;
		minor = 0xff;
	}

	/* normalize revision for the driver */
	revision = UART_BUILD_REVISION(major, minor);

	switch (revision) {
	case OMAP_UART_REV_46:
		up->errata |= (UART_ERRATA_i202_MDR1_ACCESS |
				UART_ERRATA_i291_DMA_FORCEIDLE);
		break;
	case OMAP_UART_REV_52:
		up->errata |= (UART_ERRATA_i202_MDR1_ACCESS |
				UART_ERRATA_i291_DMA_FORCEIDLE);
		up->features |= OMAP_UART_WER_HAS_TX_WAKEUP;
		break;
	case OMAP_UART_REV_63:
		up->errata |= UART_ERRATA_i202_MDR1_ACCESS;
		up->features |= OMAP_UART_WER_HAS_TX_WAKEUP;
		break;
	default:
		break;
	}
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
182
92.86%
2
66.67%
ruchika kharwar
ruchika kharwar
14
7.14%
1
33.33%
Total
196
100.00%
3
100.00%



static struct omap_uart_port_info *of_get_uart_port_info(struct device *dev)
{
	struct omap_uart_port_info *omap_up_info;

	omap_up_info = devm_kzalloc(dev, sizeof(*omap_up_info), GFP_KERNEL);
	if (!omap_up_info)
		return NULL; /* out of memory */

	of_property_read_u32(dev->of_node, "clock-frequency",
					 &omap_up_info->uartclk);
	return omap_up_info;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
rajendra nayak
rajendra nayak
45
76.27%
1
50.00%
bill pemberton
bill pemberton
14
23.73%
1
50.00%
Total
59
100.00%
2
100.00%



static int serial_omap_probe_rs485(struct uart_omap_port *up,
				   struct device_node *np)
{
	struct serial_rs485 *rs485conf = &up->port.rs485;
	u32 rs485_delay[2];
	enum of_gpio_flags flags;
	int ret;

	rs485conf->flags = 0;
	up->rts_gpio = -EINVAL;

	if (!np)
		return 0;

	if (of_property_read_bool(np, "rs485-rts-active-high"))
		rs485conf->flags |= SER_RS485_RTS_ON_SEND;
	else
		rs485conf->flags |= SER_RS485_RTS_AFTER_SEND;

	/* check for tx enable gpio */
	up->rts_gpio = of_get_named_gpio_flags(np, "rts-gpio", 0, &flags);
	if (gpio_is_valid(up->rts_gpio)) {
		ret = devm_gpio_request(up->dev, up->rts_gpio, "omap-serial");
		if (ret < 0)
			return ret;
		ret = gpio_direction_output(up->rts_gpio,
					    flags & SER_RS485_RTS_AFTER_SEND);
		if (ret < 0)
			return ret;
	} else if (up->rts_gpio == -EPROBE_DEFER) {
		return -EPROBE_DEFER;
	} else {
		up->rts_gpio = -EINVAL;
	}

	if (of_property_read_u32_array(np, "rs485-rts-delay",
				    rs485_delay, 2) == 0) {
		rs485conf->delay_rts_before_send = rs485_delay[0];
		rs485conf->delay_rts_after_send = rs485_delay[1];
	}

	if (of_property_read_bool(np, "rs485-rx-during-tx"))
		rs485conf->flags |= SER_RS485_RX_DURING_TX;

	if (of_property_read_bool(np, "linux,rs485-enabled-at-boot-time"))
		rs485conf->flags |= SER_RS485_ENABLED;

	return 0;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
mark jackson
mark jackson
227
90.08%
1
25.00%
michael grzeschik
michael grzeschik
18
7.14%
1
25.00%
felipe balbi
felipe balbi
5
1.98%
1
25.00%
ricardo ribalda
ricardo ribalda
2
0.79%
1
25.00%
Total
252
100.00%
4
100.00%



static int serial_omap_probe(struct platform_device *pdev)
{
	struct omap_uart_port_info *omap_up_info = dev_get_platdata(&pdev->dev);
	struct uart_omap_port *up;
	struct resource *mem;
	void __iomem *base;
	int uartirq = 0;
	int wakeirq = 0;
	int ret;

	/* The optional wakeirq may be specified in the board dts file */
	if (pdev->dev.of_node) {
		uartirq = irq_of_parse_and_map(pdev->dev.of_node, 0);
		if (!uartirq)
			return -EPROBE_DEFER;
		wakeirq = irq_of_parse_and_map(pdev->dev.of_node, 1);
		omap_up_info = of_get_uart_port_info(&pdev->dev);
		pdev->dev.platform_data = omap_up_info;
	} else {
		uartirq = platform_get_irq(pdev, 0);
		if (uartirq < 0)
			return -EPROBE_DEFER;
	}

	up = devm_kzalloc(&pdev->dev, sizeof(*up), GFP_KERNEL);
	if (!up)
		return -ENOMEM;

	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
	base = devm_ioremap_resource(&pdev->dev, mem);
	if (IS_ERR(base))
		return PTR_ERR(base);

	up->dev = &pdev->dev;
	up->port.dev = &pdev->dev;
	up->port.type = PORT_OMAP;
	up->port.iotype = UPIO_MEM;
	up->port.irq = uartirq;
	up->port.regshift = 2;
	up->port.fifosize = 64;
	up->port.ops = &serial_omap_pops;

	if (pdev->dev.of_node)
		ret = of_alias_get_id(pdev->dev.of_node, "serial");
	else
		ret = pdev->id;

	if (ret < 0) {
		dev_err(&pdev->dev, "failed to get alias/pdev id, errno %d\n",
			ret);
		goto err_port_line;
	}
	up->port.line = ret;

	if (up->port.line >= OMAP_MAX_HSUART_PORTS) {
		dev_err(&pdev->dev, "uart ID %d >  MAX %d.\n", up->port.line,
			OMAP_MAX_HSUART_PORTS);
		ret = -ENXIO;
		goto err_port_line;
	}

	up->wakeirq = wakeirq;
	if (!up->wakeirq)
		dev_info(up->port.dev, "no wakeirq for uart%d\n",
			 up->port.line);

	ret = serial_omap_probe_rs485(up, pdev->dev.of_node);
	if (ret < 0)
		goto err_rs485;

	sprintf(up->name, "OMAP UART%d", up->port.line);
	up->port.mapbase = mem->start;
	up->port.membase = base;
	up->port.flags = omap_up_info->flags;
	up->port.uartclk = omap_up_info->uartclk;
	up->port.rs485_config = serial_omap_config_rs485;
	if (!up->port.uartclk) {
		up->port.uartclk = DEFAULT_CLK_SPEED;
		dev_warn(&pdev->dev,
			 "No clock speed specified: using default: %d\n",
			 DEFAULT_CLK_SPEED);
	}

	up->latency = PM_QOS_CPU_DMA_LAT_DEFAULT_VALUE;
	up->calc_latency = PM_QOS_CPU_DMA_LAT_DEFAULT_VALUE;
	pm_qos_add_request(&up->pm_qos_request,
		PM_QOS_CPU_DMA_LATENCY, up->latency);
	INIT_WORK(&up->qos_work, serial_omap_uart_qos_work);

	platform_set_drvdata(pdev, up);
	if (omap_up_info->autosuspend_timeout == 0)
		omap_up_info->autosuspend_timeout = -1;

	device_init_wakeup(up->dev, true);
	pm_runtime_use_autosuspend(&pdev->dev);
	pm_runtime_set_autosuspend_delay(&pdev->dev,
			omap_up_info->autosuspend_timeout);

	pm_runtime_irq_safe(&pdev->dev);
	pm_runtime_enable(&pdev->dev);

	pm_runtime_get_sync(&pdev->dev);

	omap_serial_fill_features_erratas(up);

	ui[up->port.line] = up;
	serial_omap_add_console_port(up);

	ret = uart_add_one_port(&serial_omap_reg, &up->port);
	if (ret != 0)
		goto err_add_port;

	pm_runtime_mark_last_busy(up->dev);
	pm_runtime_put_autosuspend(up->dev);
	return 0;

err_add_port:
	pm_runtime_put(&pdev->dev);
	pm_runtime_disable(&pdev->dev);
	pm_qos_remove_request(&up->pm_qos_request);
	device_init_wakeup(up->dev, false);
err_rs485:
err_port_line:
	return ret;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
298
41.16%
5
16.67%
rajendra nayak
rajendra nayak
93
12.85%
3
10.00%
felipe balbi
felipe balbi
81
11.19%
6
20.00%
tony lindgren
tony lindgren
71
9.81%
2
6.67%
nishanth menon
nishanth menon
38
5.25%
1
3.33%
doug kehn
doug kehn
30
4.14%
1
3.33%
mark jackson
mark jackson
24
3.31%
1
3.33%
shubhrajyoti datta
shubhrajyoti datta
21
2.90%
1
3.33%
semen protsenko
semen protsenko
17
2.35%
1
3.33%
sebastian andrzej siewior
sebastian andrzej siewior
11
1.52%
1
3.33%
vikram pandita
vikram pandita
10
1.38%
1
3.33%
grygorii strashko
grygorii strashko
8
1.10%
1
3.33%
ricardo ribalda
ricardo ribalda
8
1.10%
1
3.33%
ruchika kharwar
ruchika kharwar
7
0.97%
1
3.33%
jingoo han
jingoo han
4
0.55%
1
3.33%
philippe proulx
philippe proulx
2
0.28%
2
6.67%
bill pemberton
bill pemberton
1
0.14%
1
3.33%
Total
724
100.00%
30
100.00%



static int serial_omap_remove(struct platform_device *dev)
{
	struct uart_omap_port *up = platform_get_drvdata(dev);

	pm_runtime_put_sync(up->dev);
	pm_runtime_disable(up->dev);
	uart_remove_one_port(&serial_omap_reg, &up->port);
	pm_qos_remove_request(&up->pm_qos_request);
	device_init_wakeup(&dev->dev, false);

	return 0;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
50
74.63%
3
60.00%
sanjay singh rawat
sanjay singh rawat
10
14.93%
1
20.00%
felipe balbi
felipe balbi
7
10.45%
1
20.00%
Total
67
100.00%
5
100.00%

/*
 * Work Around for Errata i202 (2430, 3430, 3630, 4430 and 4460)
 * The access to uart register after MDR1 Access
 * causes UART to corrupt data.
 *
 * Need a delay =
 * 5 L4 clock cycles + 5 UART functional clock cycle (@48MHz = ~0.2uS)
 * give 10 times as much
 */


static void serial_omap_mdr1_errataset(struct uart_omap_port *up, u8 mdr1)
{
	u8 timeout = 255;

	serial_out(up, UART_OMAP_MDR1, mdr1);
	udelay(2);
	serial_out(up, UART_FCR, up->fcr | UART_FCR_CLEAR_XMIT |
			UART_FCR_CLEAR_RCVR);
	/*
         * Wait for FIFO to empty: when empty, RX_FIFO_E bit is 0 and
         * TX_FIFO_E bit is 1.
         */
	while (UART_LSR_THRE != (serial_in(up, UART_LSR) &
				(UART_LSR_THRE | UART_LSR_DR))) {
		timeout--;
		if (!timeout) {
			/* Should *never* happen. we warn and carry on */
			dev_crit(up->dev, "Errata i202: timedout %x\n",
						serial_in(up, UART_LSR));
			break;
		}
		udelay(1);
	}
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
103
100.00%
2
100.00%
Total
103
100.00%
2
100.00%

#ifdef CONFIG_PM


static void serial_omap_restore_context(struct uart_omap_port *up)
{
	if (up->errata & UART_ERRATA_i202_MDR1_ACCESS)
		serial_omap_mdr1_errataset(up, UART_OMAP_MDR1_DISABLE);
	else
		serial_out(up, UART_OMAP_MDR1, UART_OMAP_MDR1_DISABLE);

	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); /* Config B mode */
	serial_out(up, UART_EFR, UART_EFR_ECB);
	serial_out(up, UART_LCR, 0x0); /* Operational mode */
	serial_out(up, UART_IER, 0x0);
	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); /* Config B mode */
	serial_out(up, UART_DLL, up->dll);
	serial_out(up, UART_DLM, up->dlh);
	serial_out(up, UART_LCR, 0x0); /* Operational mode */
	serial_out(up, UART_IER, up->ier);
	serial_out(up, UART_FCR, up->fcr);
	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
	serial_out(up, UART_MCR, up->mcr);
	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); /* Config B mode */
	serial_out(up, UART_OMAP_SCR, up->scr);
	serial_out(up, UART_EFR, up->efr);
	serial_out(up, UART_LCR, up->lcr);
	if (up->errata & UART_ERRATA_i202_MDR1_ACCESS)
		serial_omap_mdr1_errataset(up, up->mdr1);
	else
		serial_out(up, UART_OMAP_MDR1, up->mdr1);
	serial_out(up, UART_OMAP_WER, up->wer);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
241
100.00%
4
100.00%
Total
241
100.00%
4
100.00%



static int serial_omap_runtime_suspend(struct device *dev)
{
	struct uart_omap_port *up = dev_get_drvdata(dev);

	if (!up)
		return -EINVAL;

	/*
        * When using 'no_console_suspend', the console UART must not be
        * suspended. Since driver suspend is managed by runtime suspend,
        * preventing runtime suspend (by returning error) will keep device
        * active during suspend.
        */
	if (up->is_suspending && !console_suspend_enabled &&
	    uart_console(&up->port))
		return -EBUSY;

	up->context_loss_cnt = serial_omap_get_context_loss_count(up);

	serial_omap_enable_wakeup(up, true);

	up->latency = PM_QOS_CPU_DMA_LAT_DEFAULT_VALUE;
	schedule_work(&up->qos_work);

	return 0;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
51
60.00%
4
57.14%
sourav poddar
sourav poddar
22
25.88%
1
14.29%
wei yongjun
wei yongjun
9
10.59%
1
14.29%
felipe balbi
felipe balbi
3
3.53%
1
14.29%
Total
85
100.00%
7
100.00%



static int serial_omap_runtime_resume(struct device *dev)
{
	struct uart_omap_port *up = dev_get_drvdata(dev);

	int loss_cnt = serial_omap_get_context_loss_count(up);

	serial_omap_enable_wakeup(up, false);

	if (loss_cnt < 0) {
		dev_dbg(dev, "serial_omap_get_context_loss_count failed : %d\n",
			loss_cnt);
		serial_omap_restore_context(up);
	} else if (up->context_loss_cnt != loss_cnt) {
		serial_omap_restore_context(up);
	}
	up->latency = up->calc_latency;
	schedule_work(&up->qos_work);

	return 0;
}
Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
58
62.37%
5
55.56%
shubhrajyoti datta
shubhrajyoti datta
25
26.88%
1
11.11%
tony lindgren
tony lindgren
8
8.60%
2
22.22%
felipe balbi
felipe balbi
2
2.15%
1
11.11%
Total
93
100.00%
9
100.00%

#endif


static const struct dev_pm_ops serial_omap_dev_pm_ops = {
	SET_SYSTEM_SLEEP_PM_OPS(serial_omap_suspend, serial_omap_resume)
	SET_RUNTIME_PM_OPS(serial_omap_runtime_suspend,
				serial_omap_runtime_resume, NULL)
	.prepare        = serial_omap_prepare,
	.complete       = serial_omap_complete,
};

#if defined(CONFIG_OF)

static const struct of_device_id omap_serial_of_match[] = {
	{ .compatible = "ti,omap2-uart" },
	{ .compatible = "ti,omap3-uart" },
	{ .compatible = "ti,omap4-uart" },
	{},
};
MODULE_DEVICE_TABLE(of, omap_serial_of_match);
#endif


static struct platform_driver serial_omap_driver = {
	.probe          = serial_omap_probe,
	.remove         = serial_omap_remove,
	.driver		= {
		.name	= OMAP_SERIAL_DRIVER_NAME,
		.pm	= &serial_omap_dev_pm_ops,
		.of_match_table = of_match_ptr(omap_serial_of_match),
        },
};



static int __init serial_omap_init(void)
{
	int ret;

	ret = uart_register_driver(&serial_omap_reg);
	if (ret != 0)
		return ret;
	ret = platform_driver_register(&serial_omap_driver);
	if (ret != 0)
		uart_unregister_driver(&serial_omap_reg);
	return ret;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
52
100.00%
1
100.00%
Total
52
100.00%
1
100.00%



static void __exit serial_omap_exit(void)
{
	platform_driver_unregister(&serial_omap_driver);
	uart_unregister_driver(&serial_omap_reg);
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
21
100.00%
1
100.00%
Total
21
100.00%
1
100.00%


module_init(serial_omap_init);

module_exit(serial_omap_exit);

MODULE_DESCRIPTION("OMAP High Speed UART driver");
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Texas Instruments Inc");
Overall Contributors
Person
Tokens
Prop
Commits
CommitProp
govindraj raja
govindraj raja
4960
58.07%
12
11.01%
felipe balbi
felipe balbi
962
11.26%
20
18.35%
mark jackson
mark jackson
645
7.55%
1
0.92%
russell king
russell king
470
5.50%
10
9.17%
rajendra nayak
rajendra nayak
236
2.76%
3
2.75%
tony lindgren
tony lindgren
179
2.10%
5
4.59%
peter hurley
peter hurley
135
1.58%
3
2.75%
cosmin cojocar
cosmin cojocar
119
1.39%
1
0.92%
philippe proulx
philippe proulx
110
1.29%
3
2.75%
sourav poddar
sourav poddar
105
1.23%
1
0.92%
alexey pelykh
alexey pelykh
80
0.94%
5
4.59%
shubhrajyoti datta
shubhrajyoti datta
76
0.89%
7
6.42%
frans klaver
frans klaver
75
0.88%
2
1.83%
paul walmsley
paul walmsley
48
0.56%
2
1.83%
nishanth menon
nishanth menon
39
0.46%
1
0.92%
doug kehn
doug kehn
30
0.35%
1
0.92%
ricardo ribalda
ricardo ribalda
28
0.33%
1
0.92%
dimitris lampridis
dimitris lampridis
28
0.33%
2
1.83%
ruchika kharwar
ruchika kharwar
21
0.25%
2
1.83%
michael grzeschik
michael grzeschik
18
0.21%
1
0.92%
semen protsenko
semen protsenko
17
0.20%
1
0.92%
thomas weber
thomas weber
16
0.19%
1
0.92%
greg kroah-hartman
greg kroah-hartman
15
0.18%
3
2.75%
bill pemberton
bill pemberton
15
0.18%
1
0.92%
enric balletbo i serra
enric balletbo i serra
12
0.14%
1
0.92%
sebastian andrzej siewior
sebastian andrzej siewior
11
0.13%
1
0.92%
vikram pandita
vikram pandita
10
0.12%
1
0.92%
sanjay singh rawat
sanjay singh rawat
10
0.12%
1
0.92%
jingoo han
jingoo han
10
0.12%
1
0.92%
wei yongjun
wei yongjun
9
0.11%
1
0.92%
andrei emeltchenko
andrei emeltchenko
9
0.11%
2
1.83%
jarkko nikula
jarkko nikula
9
0.11%
1
0.92%
jiri slaby
jiri slaby
8
0.09%
1
0.92%
grygorii strashko
grygorii strashko
8
0.09%
1
0.92%
ezequiel garcia
ezequiel garcia
6
0.07%
1
0.92%
pavel machek
pavel machek
4
0.05%
1
0.92%
neil brown
neil brown
3
0.04%
1
0.92%
arnd bergmann
arnd bergmann
2
0.02%
2
1.83%
rafael j. wysocki
rafael j. wysocki
1
0.01%
1
0.92%
jean delvare
jean delvare
1
0.01%
1
0.92%
tejun heo
tejun heo
1
0.01%
1
0.92%
lucas de marchi
lucas de marchi
1
0.01%
1
0.92%
Total
8542
100.00%
109
100.00%
  
Directory: drivers/tty/serial

Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.