Release 4.7 drivers/usb/host/oxu210hp.h
/*
* Host interface registers
*/
#define OXU_DEVICEID 0x00
#define OXU_REV_MASK 0xffff0000
#define OXU_REV_SHIFT 16
#define OXU_REV_2100 0x2100
#define OXU_BO_SHIFT 8
#define OXU_BO_MASK (0x3 << OXU_BO_SHIFT)
#define OXU_MAJ_REV_SHIFT 4
#define OXU_MAJ_REV_MASK (0xf << OXU_MAJ_REV_SHIFT)
#define OXU_MIN_REV_SHIFT 0
#define OXU_MIN_REV_MASK (0xf << OXU_MIN_REV_SHIFT)
#define OXU_HOSTIFCONFIG 0x04
#define OXU_SOFTRESET 0x08
#define OXU_SRESET (1 << 0)
#define OXU_PIOBURSTREADCTRL 0x0C
#define OXU_CHIPIRQSTATUS 0x10
#define OXU_CHIPIRQEN_SET 0x14
#define OXU_CHIPIRQEN_CLR 0x18
#define OXU_USBSPHLPWUI 0x00000080
#define OXU_USBOTGLPWUI 0x00000040
#define OXU_USBSPHI 0x00000002
#define OXU_USBOTGI 0x00000001
#define OXU_CLKCTRL_SET 0x1C
#define OXU_SYSCLKEN 0x00000008
#define OXU_USBSPHCLKEN 0x00000002
#define OXU_USBOTGCLKEN 0x00000001
#define OXU_ASO 0x68
#define OXU_SPHPOEN 0x00000100
#define OXU_OVRCCURPUPDEN 0x00000800
#define OXU_ASO_OP (1 << 10)
#define OXU_COMPARATOR 0x000004000
#define OXU_USBMODE 0x1A8
#define OXU_VBPS 0x00000020
#define OXU_ES_LITTLE 0x00000000
#define OXU_CM_HOST_ONLY 0x00000003
/*
* Proper EHCI structs & defines
*/
/* Magic numbers that can affect system performance */
#define EHCI_TUNE_CERR 3
/* 0-3 qtd retries; 0 == don't stop */
#define EHCI_TUNE_RL_HS 4
/* nak throttle; see 4.9 */
#define EHCI_TUNE_RL_TT 0
#define EHCI_TUNE_MULT_HS 1
/* 1-3 transactions/uframe; 4.10.3 */
#define EHCI_TUNE_MULT_TT 1
#define EHCI_TUNE_FLS 2
/* (small) 256 frame schedule */
struct oxu_hcd;
/* EHCI register interface, corresponds to EHCI Revision 0.95 specification */
/* Section 2.2 Host Controller Capability Registers */
struct ehci_caps {
/* these fields are specified as 8 and 16 bit registers,
* but some hosts can't perform 8 or 16 bit PCI accesses.
*/
u32 hc_capbase;
#define HC_LENGTH(p) (((p)>>00)&0x00ff) /* bits 7:0 */
#define HC_VERSION(p) (((p)>>16)&0xffff) /* bits 31:16 */
u32 hcs_params; /* HCSPARAMS - offset 0x4 */
#define HCS_DEBUG_PORT(p) (((p)>>20)&0xf) /* bits 23:20, debug port? */
#define HCS_INDICATOR(p) ((p)&(1 << 16)) /* true: has port indicators */
#define HCS_N_CC(p) (((p)>>12)&0xf) /* bits 15:12, #companion HCs */
#define HCS_N_PCC(p) (((p)>>8)&0xf) /* bits 11:8, ports per CC */
#define HCS_PORTROUTED(p) ((p)&(1 << 7)) /* true: port routing */
#define HCS_PPC(p) ((p)&(1 << 4)) /* true: port power control */
#define HCS_N_PORTS(p) (((p)>>0)&0xf) /* bits 3:0, ports on HC */
u32 hcc_params; /* HCCPARAMS - offset 0x8 */
#define HCC_EXT_CAPS(p) (((p)>>8)&0xff) /* for pci extended caps */
#define HCC_ISOC_CACHE(p) ((p)&(1 << 7)) /* true: can cache isoc frame */
#define HCC_ISOC_THRES(p) (((p)>>4)&0x7) /* bits 6:4, uframes cached */
#define HCC_CANPARK(p) ((p)&(1 << 2)) /* true: can park on async qh */
#define HCC_PGM_FRAMELISTLEN(p) ((p)&(1 << 1)) /* true: periodic_size changes*/
#define HCC_64BIT_ADDR(p) ((p)&(1)) /* true: can use 64-bit addr */
u8 portroute[8]; /* nibbles for routing - offset 0xC */
} __attribute__ ((packed));
/* Section 2.3 Host Controller Operational Registers */
struct ehci_regs {
/* USBCMD: offset 0x00 */
u32 command;
/* 23:16 is r/w intr rate, in microframes; default "8" == 1/msec */
#define CMD_PARK (1<<11) /* enable "park" on async qh */
#define CMD_PARK_CNT(c) (((c)>>8)&3) /* how many transfers to park for */
#define CMD_LRESET (1<<7) /* partial reset (no ports, etc) */
#define CMD_IAAD (1<<6) /* "doorbell" interrupt async advance */
#define CMD_ASE (1<<5) /* async schedule enable */
#define CMD_PSE (1<<4) /* periodic schedule enable */
/* 3:2 is periodic frame list size */
#define CMD_RESET (1<<1) /* reset HC not bus */
#define CMD_RUN (1<<0) /* start/stop HC */
/* USBSTS: offset 0x04 */
u32 status;
#define STS_ASS (1<<15) /* Async Schedule Status */
#define STS_PSS (1<<14) /* Periodic Schedule Status */
#define STS_RECL (1<<13) /* Reclamation */
#define STS_HALT (1<<12) /* Not running (any reason) */
/* some bits reserved */
/* these STS_* flags are also intr_enable bits (USBINTR) */
#define STS_IAA (1<<5) /* Interrupted on async advance */
#define STS_FATAL (1<<4) /* such as some PCI access errors */
#define STS_FLR (1<<3) /* frame list rolled over */
#define STS_PCD (1<<2) /* port change detect */
#define STS_ERR (1<<1) /* "error" completion (overflow, ...) */
#define STS_INT (1<<0) /* "normal" completion (short, ...) */
#define INTR_MASK (STS_IAA | STS_FATAL | STS_PCD | STS_ERR | STS_INT)
/* USBINTR: offset 0x08 */
u32 intr_enable;
/* FRINDEX: offset 0x0C */
u32 frame_index; /* current microframe number */
/* CTRLDSSEGMENT: offset 0x10 */
u32 segment; /* address bits 63:32 if needed */
/* PERIODICLISTBASE: offset 0x14 */
u32 frame_list; /* points to periodic list */
/* ASYNCLISTADDR: offset 0x18 */
u32 async_next; /* address of next async queue head */
u32 reserved[9];
/* CONFIGFLAG: offset 0x40 */
u32 configured_flag;
#define FLAG_CF (1<<0) /* true: we'll support "high speed" */
/* PORTSC: offset 0x44 */
u32 port_status[0]; /* up to N_PORTS */
/* 31:23 reserved */
#define PORT_WKOC_E (1<<22) /* wake on overcurrent (enable) */
#define PORT_WKDISC_E (1<<21) /* wake on disconnect (enable) */
#define PORT_WKCONN_E (1<<20) /* wake on connect (enable) */
/* 19:16 for port testing */
#define PORT_LED_OFF (0<<14)
#define PORT_LED_AMBER (1<<14)
#define PORT_LED_GREEN (2<<14)
#define PORT_LED_MASK (3<<14)
#define PORT_OWNER (1<<13) /* true: companion hc owns this port */
#define PORT_POWER (1<<12) /* true: has power (see PPC) */
#define PORT_USB11(x) (((x)&(3<<10)) == (1<<10)) /* USB 1.1 device */
/* 11:10 for detecting lowspeed devices (reset vs release ownership) */
/* 9 reserved */
#define PORT_RESET (1<<8) /* reset port */
#define PORT_SUSPEND (1<<7) /* suspend port */
#define PORT_RESUME (1<<6) /* resume it */
#define PORT_OCC (1<<5) /* over current change */
#define PORT_OC (1<<4) /* over current active */
#define PORT_PEC (1<<3) /* port enable change */
#define PORT_PE (1<<2) /* port enable */
#define PORT_CSC (1<<1) /* connect status change */
#define PORT_CONNECT (1<<0) /* device connected */
#define PORT_RWC_BITS (PORT_CSC | PORT_PEC | PORT_OCC)
} __attribute__ ((packed));
/* Appendix C, Debug port ... intended for use with special "debug devices"
* that can help if there's no serial console. (nonstandard enumeration.)
*/
struct ehci_dbg_port {
u32 control;
#define DBGP_OWNER (1<<30)
#define DBGP_ENABLED (1<<28)
#define DBGP_DONE (1<<16)
#define DBGP_INUSE (1<<10)
#define DBGP_ERRCODE(x) (((x)>>7)&0x07)
# define DBGP_ERR_BAD 1
# define DBGP_ERR_SIGNAL 2
#define DBGP_ERROR (1<<6)
#define DBGP_GO (1<<5)
#define DBGP_OUT (1<<4)
#define DBGP_LEN(x) (((x)>>0)&0x0f)
u32 pids;
#define DBGP_PID_GET(x) (((x)>>16)&0xff)
#define DBGP_PID_SET(data, tok) (((data)<<8)|(tok))
u32 data03;
u32 data47;
u32 address;
#define DBGP_EPADDR(dev, ep) (((dev)<<8)|(ep))
} __attribute__ ((packed));
#define QTD_NEXT(dma) cpu_to_le32((u32)dma)
/*
* EHCI Specification 0.95 Section 3.5
* QTD: describe data transfer components (buffer, direction, ...)
* See Fig 3-6 "Queue Element Transfer Descriptor Block Diagram".
*
* These are associated only with "QH" (Queue Head) structures,
* used with control, bulk, and interrupt transfers.
*/
struct ehci_qtd {
/* first part defined by EHCI spec */
__le32 hw_next; /* see EHCI 3.5.1 */
__le32 hw_alt_next; /* see EHCI 3.5.2 */
__le32 hw_token; /* see EHCI 3.5.3 */
#define QTD_TOGGLE (1 << 31) /* data toggle */
#define QTD_LENGTH(tok) (((tok)>>16) & 0x7fff)
#define QTD_IOC (1 << 15) /* interrupt on complete */
#define QTD_CERR(tok) (((tok)>>10) & 0x3)
#define QTD_PID(tok) (((tok)>>8) & 0x3)
#define QTD_STS_ACTIVE (1 << 7) /* HC may execute this */
#define QTD_STS_HALT (1 << 6) /* halted on error */
#define QTD_STS_DBE (1 << 5) /* data buffer error (in HC) */
#define QTD_STS_BABBLE (1 << 4) /* device was babbling (qtd halted) */
#define QTD_STS_XACT (1 << 3) /* device gave illegal response */
#define QTD_STS_MMF (1 << 2) /* incomplete split transaction */
#define QTD_STS_STS (1 << 1) /* split transaction state */
#define QTD_STS_PING (1 << 0) /* issue PING? */
__le32 hw_buf[5]; /* see EHCI 3.5.4 */
__le32 hw_buf_hi[5]; /* Appendix B */
/* the rest is HCD-private */
dma_addr_t qtd_dma; /* qtd address */
struct list_head qtd_list; /* sw qtd list */
struct urb *urb; /* qtd's urb */
size_t length; /* length of buffer */
u32 qtd_buffer_len;
void *buffer;
dma_addr_t buffer_dma;
void *transfer_buffer;
void *transfer_dma;
} __attribute__ ((aligned(32)));
/* mask NakCnt+T in qh->hw_alt_next */
#define QTD_MASK cpu_to_le32 (~0x1f)
#define IS_SHORT_READ(token) (QTD_LENGTH(token) != 0 && QTD_PID(token) == 1)
/* Type tag from {qh, itd, sitd, fstn}->hw_next */
#define Q_NEXT_TYPE(dma) ((dma) & cpu_to_le32 (3 << 1))
/* values for that type tag */
#define Q_TYPE_QH cpu_to_le32 (1 << 1)
/* next async queue entry, or pointer to interrupt/periodic QH */
#define QH_NEXT(dma) (cpu_to_le32(((u32)dma)&~0x01f)|Q_TYPE_QH)
/* for periodic/async schedules and qtd lists, mark end of list */
#define EHCI_LIST_END cpu_to_le32(1)
/* "null pointer" to hw */
/*
* Entries in periodic shadow table are pointers to one of four kinds
* of data structure. That's dictated by the hardware; a type tag is
* encoded in the low bits of the hardware's periodic schedule. Use
* Q_NEXT_TYPE to get the tag.
*
* For entries in the async schedule, the type tag always says "qh".
*/
union ehci_shadow {
struct ehci_qh *qh; /* Q_TYPE_QH */
__le32 *hw_next; /* (all types) */
void *ptr;
};
/*
* EHCI Specification 0.95 Section 3.6
* QH: describes control/bulk/interrupt endpoints
* See Fig 3-7 "Queue Head Structure Layout".
*
* These appear in both the async and (for interrupt) periodic schedules.
*/
struct ehci_qh {
/* first part defined by EHCI spec */
__le32 hw_next; /* see EHCI 3.6.1 */
__le32 hw_info1; /* see EHCI 3.6.2 */
#define QH_HEAD 0x00008000
__le32 hw_info2; /* see EHCI 3.6.2 */
#define QH_SMASK 0x000000ff
#define QH_CMASK 0x0000ff00
#define QH_HUBADDR 0x007f0000
#define QH_HUBPORT 0x3f800000
#define QH_MULT 0xc0000000
__le32 hw_current; /* qtd list - see EHCI 3.6.4 */
/* qtd overlay (hardware parts of a struct ehci_qtd) */
__le32 hw_qtd_next;
__le32 hw_alt_next;
__le32 hw_token;
__le32 hw_buf[5];
__le32 hw_buf_hi[5];
/* the rest is HCD-private */
dma_addr_t qh_dma; /* address of qh */
union ehci_shadow qh_next; /* ptr to qh; or periodic */
struct list_head qtd_list; /* sw qtd list */
struct ehci_qtd *dummy;
struct ehci_qh *reclaim; /* next to reclaim */
struct oxu_hcd *oxu;
struct kref kref;
unsigned stamp;
u8 qh_state;
#define QH_STATE_LINKED 1 /* HC sees this */
#define QH_STATE_UNLINK 2 /* HC may still see this */
#define QH_STATE_IDLE 3 /* HC doesn't see this */
#define QH_STATE_UNLINK_WAIT 4 /* LINKED and on reclaim q */
#define QH_STATE_COMPLETING 5 /* don't touch token.HALT */
/* periodic schedule info */
u8 usecs; /* intr bandwidth */
u8 gap_uf; /* uframes split/csplit gap */
u8 c_usecs; /* ... split completion bw */
u16 tt_usecs; /* tt downstream bandwidth */
unsigned short period; /* polling interval */
unsigned short start; /* where polling starts */
#define NO_FRAME ((unsigned short)~0) /* pick new start */
struct usb_device *dev; /* access to TT */
} __attribute__ ((aligned(32)));
/*
* Proper OXU210HP structs
*/
#define OXU_OTG_CORE_OFFSET 0x00400
#define OXU_OTG_CAP_OFFSET (OXU_OTG_CORE_OFFSET + 0x100)
#define OXU_SPH_CORE_OFFSET 0x00800
#define OXU_SPH_CAP_OFFSET (OXU_SPH_CORE_OFFSET + 0x100)
#define OXU_OTG_MEM 0xE000
#define OXU_SPH_MEM 0x16000
/* Only how many elements & element structure are specifies here. */
/* 2 host controllers are enabled - total size <= 28 kbytes */
#define DEFAULT_I_TDPS 1024
#define QHEAD_NUM 16
#define QTD_NUM 32
#define SITD_NUM 8
#define MURB_NUM 8
#define BUFFER_NUM 8
#define BUFFER_SIZE 512
struct oxu_info {
struct usb_hcd *hcd[2];
};
struct oxu_buf {
u8 buffer[BUFFER_SIZE];
} __attribute__ ((aligned(BUFFER_SIZE)));
struct oxu_onchip_mem {
struct oxu_buf db_pool[BUFFER_NUM];
u32 frame_list[DEFAULT_I_TDPS];
struct ehci_qh qh_pool[QHEAD_NUM];
struct ehci_qtd qtd_pool[QTD_NUM];
} __attribute__ ((aligned(4 << 10)));
#define EHCI_MAX_ROOT_PORTS 15
/* see HCS_N_PORTS */
struct oxu_murb {
struct urb urb;
struct urb *main;
u8 last;
};
struct oxu_hcd { /* one per controller */
unsigned int is_otg:1;
u8 qh_used[QHEAD_NUM];
u8 qtd_used[QTD_NUM];
u8 db_used[BUFFER_NUM];
u8 murb_used[MURB_NUM];
struct oxu_onchip_mem __iomem *mem;
spinlock_t mem_lock;
struct timer_list urb_timer;
struct ehci_caps __iomem *caps;
struct ehci_regs __iomem *regs;
__u32 hcs_params; /* cached register copy */
spinlock_t lock;
/* async schedule support */
struct ehci_qh *async;
struct ehci_qh *reclaim;
unsigned reclaim_ready:1;
unsigned scanning:1;
/* periodic schedule support */
unsigned periodic_size;
__le32 *periodic; /* hw periodic table */
dma_addr_t periodic_dma;
unsigned i_thresh; /* uframes HC might cache */
union ehci_shadow *pshadow; /* mirror hw periodic table */
int next_uframe; /* scan periodic, start here */
unsigned periodic_sched; /* periodic activity count */
/* per root hub port */
unsigned long reset_done[EHCI_MAX_ROOT_PORTS];
/* bit vectors (one bit per port) */
unsigned long bus_suspended; /* which ports were
* already suspended at the
* start of a bus suspend
*/
unsigned long companion_ports;/* which ports are dedicated
* to the companion controller
*/
struct timer_list watchdog;
unsigned long actions;
unsigned stamp;
unsigned long next_statechange;
u32 command;
/* SILICON QUIRKS */
struct list_head urb_list; /* this is the head to urb
* queue that didn't get enough
* resources
*/
struct oxu_murb *murb_pool; /* murb per split big urb */
unsigned urb_len;
u8 sbrn; /* packed release number */
};
#define EHCI_IAA_JIFFIES (HZ/100)
/* arbitrary; ~10 msec */
#define EHCI_IO_JIFFIES (HZ/10)
/* io watchdog > irq_thresh */
#define EHCI_ASYNC_JIFFIES (HZ/20)
/* async idle timeout */
#define EHCI_SHRINK_JIFFIES (HZ/200)
/* async qh unlink delay */
enum ehci_timer_action {
TIMER_IO_WATCHDOG,
TIMER_IAA_WATCHDOG,
TIMER_ASYNC_SHRINK,
TIMER_ASYNC_OFF,
};
#include <linux/oxu210hp.h>
Overall Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| rodolfo giometti | rodolfo giometti | 1453 | 99.73% | 1 | 50.00% |
| harvey harrison | harvey harrison | 4 | 0.27% | 1 | 50.00% |
| Total | 1457 | 100.00% | 2 | 100.00% |
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.