Release 4.7 drivers/usb/host/uhci-hcd.h
#ifndef __LINUX_UHCI_HCD_H
#define __LINUX_UHCI_HCD_H
#include <linux/list.h>
#include <linux/usb.h>
#define usb_packetid(pipe) (usb_pipein(pipe) ? USB_PID_IN : USB_PID_OUT)
#define PIPE_DEVEP_MASK 0x0007ff00
/*
* Universal Host Controller Interface data structures and defines
*/
/* Command register */
#define USBCMD 0
#define USBCMD_RS 0x0001
/* Run/Stop */
#define USBCMD_HCRESET 0x0002
/* Host reset */
#define USBCMD_GRESET 0x0004
/* Global reset */
#define USBCMD_EGSM 0x0008
/* Global Suspend Mode */
#define USBCMD_FGR 0x0010
/* Force Global Resume */
#define USBCMD_SWDBG 0x0020
/* SW Debug mode */
#define USBCMD_CF 0x0040
/* Config Flag (sw only) */
#define USBCMD_MAXP 0x0080
/* Max Packet (0 = 32, 1 = 64) */
/* Status register */
#define USBSTS 2
#define USBSTS_USBINT 0x0001
/* Interrupt due to IOC */
#define USBSTS_ERROR 0x0002
/* Interrupt due to error */
#define USBSTS_RD 0x0004
/* Resume Detect */
#define USBSTS_HSE 0x0008
/* Host System Error: PCI problems */
#define USBSTS_HCPE 0x0010
/* Host Controller Process Error:
* the schedule is buggy */
#define USBSTS_HCH 0x0020
/* HC Halted */
/* Interrupt enable register */
#define USBINTR 4
#define USBINTR_TIMEOUT 0x0001
/* Timeout/CRC error enable */
#define USBINTR_RESUME 0x0002
/* Resume interrupt enable */
#define USBINTR_IOC 0x0004
/* Interrupt On Complete enable */
#define USBINTR_SP 0x0008
/* Short packet interrupt enable */
#define USBFRNUM 6
#define USBFLBASEADD 8
#define USBSOF 12
#define USBSOF_DEFAULT 64
/* Frame length is exactly 1 ms */
/* USB port status and control registers */
#define USBPORTSC1 16
#define USBPORTSC2 18
#define USBPORTSC_CCS 0x0001
/* Current Connect Status
* ("device present") */
#define USBPORTSC_CSC 0x0002
/* Connect Status Change */
#define USBPORTSC_PE 0x0004
/* Port Enable */
#define USBPORTSC_PEC 0x0008
/* Port Enable Change */
#define USBPORTSC_DPLUS 0x0010
/* D+ high (line status) */
#define USBPORTSC_DMINUS 0x0020
/* D- high (line status) */
#define USBPORTSC_RD 0x0040
/* Resume Detect */
#define USBPORTSC_RES1 0x0080
/* reserved, always 1 */
#define USBPORTSC_LSDA 0x0100
/* Low Speed Device Attached */
#define USBPORTSC_PR 0x0200
/* Port Reset */
/* OC and OCC from Intel 430TX and later (not UHCI 1.1d spec) */
#define USBPORTSC_OC 0x0400
/* Over Current condition */
#define USBPORTSC_OCC 0x0800
/* Over Current Change R/WC */
#define USBPORTSC_SUSP 0x1000
/* Suspend */
#define USBPORTSC_RES2 0x2000
/* reserved, write zeroes */
#define USBPORTSC_RES3 0x4000
/* reserved, write zeroes */
#define USBPORTSC_RES4 0x8000
/* reserved, write zeroes */
/* PCI legacy support register */
#define USBLEGSUP 0xc0
#define USBLEGSUP_DEFAULT 0x2000
/* only PIRQ enable set */
#define USBLEGSUP_RWC 0x8f00
/* the R/WC bits */
#define USBLEGSUP_RO 0x5040
/* R/O and reserved bits */
/* PCI Intel-specific resume-enable register */
#define USBRES_INTEL 0xc4
#define USBPORT1EN 0x01
#define USBPORT2EN 0x02
#define UHCI_PTR_BITS(uhci) cpu_to_hc32((uhci), 0x000F)
#define UHCI_PTR_TERM(uhci) cpu_to_hc32((uhci), 0x0001)
#define UHCI_PTR_QH(uhci) cpu_to_hc32((uhci), 0x0002)
#define UHCI_PTR_DEPTH(uhci) cpu_to_hc32((uhci), 0x0004)
#define UHCI_PTR_BREADTH(uhci) cpu_to_hc32((uhci), 0x0000)
#define UHCI_NUMFRAMES 1024
/* in the frame list [array] */
#define UHCI_MAX_SOF_NUMBER 2047
/* in an SOF packet */
#define CAN_SCHEDULE_FRAMES 1000
/* how far in the future frames
* can be scheduled */
#define MAX_PHASE 32
/* Periodic scheduling length */
/* When no queues need Full-Speed Bandwidth Reclamation,
* delay this long before turning FSBR off */
#define FSBR_OFF_DELAY msecs_to_jiffies(10)
/* If a queue hasn't advanced after this much time, assume it is stuck */
#define QH_WAIT_TIMEOUT msecs_to_jiffies(200)
/*
* __hc32 and __hc16 are "Host Controller" types, they may be equivalent to
* __leXX (normally) or __beXX (given UHCI_BIG_ENDIAN_DESC), depending on
* the host controller implementation.
*
* To facilitate the strongest possible byte-order checking from "sparse"
* and so on, we use __leXX unless that's not practical.
*/
#ifdef CONFIG_USB_UHCI_BIG_ENDIAN_DESC
typedef __u32 __bitwise __hc32;
typedef __u16 __bitwise __hc16;
#else
#define __hc32 __le32
#define __hc16 __le16
#endif
/*
* Queue Headers
*/
/*
* One role of a QH is to hold a queue of TDs for some endpoint. One QH goes
* with each endpoint, and qh->element (updated by the HC) is either:
* - the next unprocessed TD in the endpoint's queue, or
* - UHCI_PTR_TERM (when there's no more traffic for this endpoint).
*
* The other role of a QH is to serve as a "skeleton" framelist entry, so we
* can easily splice a QH for some endpoint into the schedule at the right
* place. Then qh->element is UHCI_PTR_TERM.
*
* In the schedule, qh->link maintains a list of QHs seen by the HC:
* skel1 --> ep1-qh --> ep2-qh --> ... --> skel2 --> ...
*
* qh->node is the software equivalent of qh->link. The differences
* are that the software list is doubly-linked and QHs in the UNLINKING
* state are on the software list but not the hardware schedule.
*
* For bookkeeping purposes we maintain QHs even for Isochronous endpoints,
* but they never get added to the hardware schedule.
*/
#define QH_STATE_IDLE 1
/* QH is not being used */
#define QH_STATE_UNLINKING 2
/* QH has been removed from the
* schedule but the hardware may
* still be using it */
#define QH_STATE_ACTIVE 3
/* QH is on the schedule */
struct uhci_qh {
/* Hardware fields */
__hc32 link; /* Next QH in the schedule */
__hc32 element; /* Queue element (TD) pointer */
/* Software fields */
dma_addr_t dma_handle;
struct list_head node; /* Node in the list of QHs */
struct usb_host_endpoint *hep; /* Endpoint information */
struct usb_device *udev;
struct list_head queue; /* Queue of urbps for this QH */
struct uhci_td *dummy_td; /* Dummy TD to end the queue */
struct uhci_td *post_td; /* Last TD completed */
struct usb_iso_packet_descriptor *iso_packet_desc;
/* Next urb->iso_frame_desc entry */
unsigned long advance_jiffies; /* Time of last queue advance */
unsigned int unlink_frame; /* When the QH was unlinked */
unsigned int period; /* For Interrupt and Isochronous QHs */
short phase; /* Between 0 and period-1 */
short load; /* Periodic time requirement, in us */
unsigned int iso_frame; /* Frame # for iso_packet_desc */
int state; /* QH_STATE_xxx; see above */
int type; /* Queue type (control, bulk, etc) */
int skel; /* Skeleton queue number */
unsigned int initial_toggle:1; /* Endpoint's current toggle value */
unsigned int needs_fixup:1; /* Must fix the TD toggle values */
unsigned int is_stopped:1; /* Queue was stopped by error/unlink */
unsigned int wait_expired:1; /* QH_WAIT_TIMEOUT has expired */
unsigned int bandwidth_reserved:1; /* Periodic bandwidth has
* been allocated */
} __attribute__((aligned(16)));
/*
* We need a special accessor for the element pointer because it is
* subject to asynchronous updates by the controller.
*/
#define qh_element(qh) ACCESS_ONCE((qh)->element)
#define LINK_TO_QH(uhci, qh) (UHCI_PTR_QH((uhci)) | \
cpu_to_hc32((uhci), (qh)->dma_handle))
/*
* Transfer Descriptors
*/
/*
* for TD <status>:
*/
#define TD_CTRL_SPD (1 << 29)
/* Short Packet Detect */
#define TD_CTRL_C_ERR_MASK (3 << 27)
/* Error Counter bits */
#define TD_CTRL_C_ERR_SHIFT 27
#define TD_CTRL_LS (1 << 26)
/* Low Speed Device */
#define TD_CTRL_IOS (1 << 25)
/* Isochronous Select */
#define TD_CTRL_IOC (1 << 24)
/* Interrupt on Complete */
#define TD_CTRL_ACTIVE (1 << 23)
/* TD Active */
#define TD_CTRL_STALLED (1 << 22)
/* TD Stalled */
#define TD_CTRL_DBUFERR (1 << 21)
/* Data Buffer Error */
#define TD_CTRL_BABBLE (1 << 20)
/* Babble Detected */
#define TD_CTRL_NAK (1 << 19)
/* NAK Received */
#define TD_CTRL_CRCTIMEO (1 << 18)
/* CRC/Time Out Error */
#define TD_CTRL_BITSTUFF (1 << 17)
/* Bit Stuff Error */
#define TD_CTRL_ACTLEN_MASK 0x7FF
/* actual length, encoded as n - 1 */
#define uhci_maxerr(err) ((err) << TD_CTRL_C_ERR_SHIFT)
#define uhci_status_bits(ctrl_sts) ((ctrl_sts) & 0xF60000)
#define uhci_actual_length(ctrl_sts) (((ctrl_sts) + 1) & \
TD_CTRL_ACTLEN_MASK) /* 1-based */
/*
* for TD <info>: (a.k.a. Token)
*/
#define td_token(uhci, td) hc32_to_cpu((uhci), (td)->token)
#define TD_TOKEN_DEVADDR_SHIFT 8
#define TD_TOKEN_TOGGLE_SHIFT 19
#define TD_TOKEN_TOGGLE (1 << 19)
#define TD_TOKEN_EXPLEN_SHIFT 21
#define TD_TOKEN_EXPLEN_MASK 0x7FF
/* expected length, encoded as n-1 */
#define TD_TOKEN_PID_MASK 0xFF
#define uhci_explen(len) ((((len) - 1) & TD_TOKEN_EXPLEN_MASK) << \
TD_TOKEN_EXPLEN_SHIFT)
#define uhci_expected_length(token) ((((token) >> TD_TOKEN_EXPLEN_SHIFT) + \
1) & TD_TOKEN_EXPLEN_MASK)
#define uhci_toggle(token) (((token) >> TD_TOKEN_TOGGLE_SHIFT) & 1)
#define uhci_endpoint(token) (((token) >> 15) & 0xf)
#define uhci_devaddr(token) (((token) >> TD_TOKEN_DEVADDR_SHIFT) & 0x7f)
#define uhci_devep(token) (((token) >> TD_TOKEN_DEVADDR_SHIFT) & 0x7ff)
#define uhci_packetid(token) ((token) & TD_TOKEN_PID_MASK)
#define uhci_packetout(token) (uhci_packetid(token) != USB_PID_IN)
#define uhci_packetin(token) (uhci_packetid(token) == USB_PID_IN)
/*
* The documentation says "4 words for hardware, 4 words for software".
*
* That's silly, the hardware doesn't care. The hardware only cares that
* the hardware words are 16-byte aligned, and we can have any amount of
* sw space after the TD entry.
*
* td->link points to either another TD (not necessarily for the same urb or
* even the same endpoint), or nothing (PTR_TERM), or a QH.
*/
struct uhci_td {
/* Hardware fields */
__hc32 link;
__hc32 status;
__hc32 token;
__hc32 buffer;
/* Software fields */
dma_addr_t dma_handle;
struct list_head list;
int frame; /* for iso: what frame? */
struct list_head fl_list;
} __attribute__((aligned(16)));
/*
* We need a special accessor for the control/status word because it is
* subject to asynchronous updates by the controller.
*/
#define td_status(uhci, td) hc32_to_cpu((uhci), \
ACCESS_ONCE((td)->status))
#define LINK_TO_TD(uhci, td) (cpu_to_hc32((uhci), (td)->dma_handle))
/*
* Skeleton Queue Headers
*/
/*
* The UHCI driver uses QHs with Interrupt, Control and Bulk URBs for
* automatic queuing. To make it easy to insert entries into the schedule,
* we have a skeleton of QHs for each predefined Interrupt latency.
* Asynchronous QHs (low-speed control, full-speed control, and bulk)
* go onto the period-1 interrupt list, since they all get accessed on
* every frame.
*
* When we want to add a new QH, we add it to the list starting from the
* appropriate skeleton QH. For instance, the schedule can look like this:
*
* skel int128 QH
* dev 1 interrupt QH
* dev 5 interrupt QH
* skel int64 QH
* skel int32 QH
* ...
* skel int1 + async QH
* dev 5 low-speed control QH
* dev 1 bulk QH
* dev 2 bulk QH
*
* There is a special terminating QH used to keep full-speed bandwidth
* reclamation active when no full-speed control or bulk QHs are linked
* into the schedule. It has an inactive TD (to work around a PIIX bug,
* see the Intel errata) and it points back to itself.
*
* There's a special skeleton QH for Isochronous QHs which never appears
* on the schedule. Isochronous TDs go on the schedule before the
* the skeleton QHs. The hardware accesses them directly rather than
* through their QH, which is used only for bookkeeping purposes.
* While the UHCI spec doesn't forbid the use of QHs for Isochronous,
* it doesn't use them either. And the spec says that queues never
* advance on an error completion status, which makes them totally
* unsuitable for Isochronous transfers.
*
* There's also a special skeleton QH used for QHs which are in the process
* of unlinking and so may still be in use by the hardware. It too never
* appears on the schedule.
*/
#define UHCI_NUM_SKELQH 11
#define SKEL_UNLINK 0
#define skel_unlink_qh skelqh[SKEL_UNLINK]
#define SKEL_ISO 1
#define skel_iso_qh skelqh[SKEL_ISO]
/* int128, int64, ..., int1 = 2, 3, ..., 9 */
#define SKEL_INDEX(exponent) (9 - exponent)
#define SKEL_ASYNC 9
#define skel_async_qh skelqh[SKEL_ASYNC]
#define SKEL_TERM 10
#define skel_term_qh skelqh[SKEL_TERM]
/* The following entries refer to sublists of skel_async_qh */
#define SKEL_LS_CONTROL 20
#define SKEL_FS_CONTROL 21
#define SKEL_FSBR SKEL_FS_CONTROL
#define SKEL_BULK 22
/*
* The UHCI controller and root hub
*/
/*
* States for the root hub:
*
* To prevent "bouncing" in the presence of electrical noise,
* when there are no devices attached we delay for 1 second in the
* RUNNING_NODEVS state before switching to the AUTO_STOPPED state.
*
* (Note that the AUTO_STOPPED state won't be necessary once the hub
* driver learns to autosuspend.)
*/
enum uhci_rh_state {
/* In the following states the HC must be halted.
* These two must come first. */
UHCI_RH_RESET,
UHCI_RH_SUSPENDED,
UHCI_RH_AUTO_STOPPED,
UHCI_RH_RESUMING,
/* In this state the HC changes from running to halted,
* so it can legally appear either way. */
UHCI_RH_SUSPENDING,
/* In the following states it's an error if the HC is halted.
* These two must come last. */
UHCI_RH_RUNNING, /* The normal state */
UHCI_RH_RUNNING_NODEVS, /* Running with no devices attached */
};
/*
* The full UHCI controller information:
*/
struct uhci_hcd {
/* debugfs */
struct dentry *dentry;
/* Grabbed from PCI */
unsigned long io_addr;
/* Used when registers are memory mapped */
void __iomem *regs;
struct dma_pool *qh_pool;
struct dma_pool *td_pool;
struct uhci_td *term_td; /* Terminating TD, see UHCI bug */
struct uhci_qh *skelqh[UHCI_NUM_SKELQH]; /* Skeleton QHs */
struct uhci_qh *next_qh; /* Next QH to scan */
spinlock_t lock;
dma_addr_t frame_dma_handle; /* Hardware frame list */
__hc32 *frame;
void **frame_cpu; /* CPU's frame list */
enum uhci_rh_state rh_state;
unsigned long auto_stop_time; /* When to AUTO_STOP */
unsigned int frame_number; /* As of last check */
unsigned int is_stopped;
#define UHCI_IS_STOPPED 9999 /* Larger than a frame # */
unsigned int last_iso_frame; /* Frame of last scan */
unsigned int cur_iso_frame; /* Frame for current scan */
unsigned int scan_in_progress:1; /* Schedule scan is running */
unsigned int need_rescan:1; /* Redo the schedule scan */
unsigned int dead:1; /* Controller has died */
unsigned int RD_enable:1; /* Suspended root hub with
Resume-Detect interrupts
enabled */
unsigned int is_initialized:1; /* Data structure is usable */
unsigned int fsbr_is_on:1; /* FSBR is turned on */
unsigned int fsbr_is_wanted:1; /* Does any URB want FSBR? */
unsigned int fsbr_expiring:1; /* FSBR is timing out */
struct timer_list fsbr_timer; /* For turning off FBSR */
/* Silicon quirks */
unsigned int oc_low:1; /* OverCurrent bit active low */
unsigned int wait_for_hp:1; /* Wait for HP port reset */
unsigned int big_endian_mmio:1; /* Big endian registers */
unsigned int big_endian_desc:1; /* Big endian descriptors */
/* Support for port suspend/resume/reset */
unsigned long port_c_suspend; /* Bit-arrays of ports */
unsigned long resuming_ports;
unsigned long ports_timeout; /* Time to stop signalling */
struct list_head idle_qh_list; /* Where the idle QHs live */
int rh_numports; /* Number of root-hub ports */
wait_queue_head_t waitqh; /* endpoint_disable waiters */
int num_waiting; /* Number of waiters */
int total_load; /* Sum of array values */
short load[MAX_PHASE]; /* Periodic allocations */
/* Reset host controller */
void (*reset_hc) (struct uhci_hcd *uhci);
int (*check_and_reset_hc) (struct uhci_hcd *uhci);
/* configure_hc should perform arch specific settings, if needed */
void (*configure_hc) (struct uhci_hcd *uhci);
/* Check for broken resume detect interrupts */
int (*resume_detect_interrupts_are_broken) (struct uhci_hcd *uhci);
/* Check for broken global suspend */
int (*global_suspend_mode_is_broken) (struct uhci_hcd *uhci);
};
/* Convert between a usb_hcd pointer and the corresponding uhci_hcd */
static inline struct uhci_hcd *hcd_to_uhci(struct usb_hcd *hcd)
{
return (struct uhci_hcd *) (hcd->hcd_priv);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| alan stern | alan stern | 26 | 100.00% | 1 | 100.00% |
| Total | 26 | 100.00% | 1 | 100.00% |
static inline struct usb_hcd *uhci_to_hcd(struct uhci_hcd *uhci)
{
return container_of((void *) uhci, struct usb_hcd, hcd_priv);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| alan stern | alan stern | 29 | 100.00% | 1 | 100.00% |
| Total | 29 | 100.00% | 1 | 100.00% |
#define uhci_dev(u) (uhci_to_hcd(u)->self.controller)
/* Utility macro for comparing frame numbers */
#define uhci_frame_before_eq(f1, f2) (0 <= (int) ((f2) - (f1)))
/*
* Private per-URB data
*/
struct urb_priv {
struct list_head node; /* Node in the QH's urbp list */
struct urb *urb;
struct uhci_qh *qh; /* QH for this URB */
struct list_head td_list;
unsigned fsbr:1; /* URB wants FSBR */
};
/* Some special IDs */
#define PCI_VENDOR_ID_GENESYS 0x17a0
#define PCI_DEVICE_ID_GL880S_UHCI 0x8083
/*
* Functions used to access controller registers. The UCHI spec says that host
* controller I/O registers are mapped into PCI I/O space. For non-PCI hosts
* we use memory mapped registers.
*/
#ifndef CONFIG_USB_UHCI_SUPPORT_NON_PCI_HC
/* Support PCI only */
static inline u32 uhci_readl(const struct uhci_hcd *uhci, int reg)
{
return inl(uhci->io_addr + reg);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| jan andersson | jan andersson | 26 | 100.00% | 2 | 100.00% |
| Total | 26 | 100.00% | 2 | 100.00% |
static inline void uhci_writel(const struct uhci_hcd *uhci, u32 val, int reg)
{
outl(val, uhci->io_addr + reg);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| jan andersson | jan andersson | 30 | 100.00% | 2 | 100.00% |
| Total | 30 | 100.00% | 2 | 100.00% |
static inline u16 uhci_readw(const struct uhci_hcd *uhci, int reg)
{
return inw(uhci->io_addr + reg);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| jan andersson | jan andersson | 26 | 100.00% | 2 | 100.00% |
| Total | 26 | 100.00% | 2 | 100.00% |
static inline void uhci_writew(const struct uhci_hcd *uhci, u16 val, int reg)
{
outw(val, uhci->io_addr + reg);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| jan andersson | jan andersson | 30 | 100.00% | 2 | 100.00% |
| Total | 30 | 100.00% | 2 | 100.00% |
static inline u8 uhci_readb(const struct uhci_hcd *uhci, int reg)
{
return inb(uhci->io_addr + reg);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| jan andersson | jan andersson | 26 | 100.00% | 2 | 100.00% |
| Total | 26 | 100.00% | 2 | 100.00% |
static inline void uhci_writeb(const struct uhci_hcd *uhci, u8 val, int reg)
{
outb(val, uhci->io_addr + reg);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| jan andersson | jan andersson | 30 | 100.00% | 2 | 100.00% |
| Total | 30 | 100.00% | 2 | 100.00% |
#else
/* Support non-PCI host controllers */
#ifdef CONFIG_PCI
/* Support PCI and non-PCI host controllers */
#define uhci_has_pci_registers(u) ((u)->io_addr != 0)
#else
/* Support non-PCI host controllers only */
#define uhci_has_pci_registers(u) 0
#endif
#ifdef CONFIG_USB_UHCI_BIG_ENDIAN_MMIO
/* Support (non-PCI) big endian host controllers */
#define uhci_big_endian_mmio(u) ((u)->big_endian_mmio)
#else
#define uhci_big_endian_mmio(u) 0
#endif
static inline u32 uhci_readl(const struct uhci_hcd *uhci, int reg)
{
if (uhci_has_pci_registers(uhci))
return inl(uhci->io_addr + reg);
#ifdef CONFIG_USB_UHCI_BIG_ENDIAN_MMIO
else if (uhci_big_endian_mmio(uhci))
return readl_be(uhci->regs + reg);
#endif
else
return readl(uhci->regs + reg);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| jan andersson | jan andersson | 67 | 100.00% | 2 | 100.00% |
| Total | 67 | 100.00% | 2 | 100.00% |
static inline void uhci_writel(const struct uhci_hcd *uhci, u32 val, int reg)
{
if (uhci_has_pci_registers(uhci))
outl(val, uhci->io_addr + reg);
#ifdef CONFIG_USB_UHCI_BIG_ENDIAN_MMIO
else if (uhci_big_endian_mmio(uhci))
writel_be(val, uhci->regs + reg);
#endif
else
writel(val, uhci->regs + reg);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| jan andersson | jan andersson | 73 | 100.00% | 2 | 100.00% |
| Total | 73 | 100.00% | 2 | 100.00% |
static inline u16 uhci_readw(const struct uhci_hcd *uhci, int reg)
{
if (uhci_has_pci_registers(uhci))
return inw(uhci->io_addr + reg);
#ifdef CONFIG_USB_UHCI_BIG_ENDIAN_MMIO
else if (uhci_big_endian_mmio(uhci))
return readw_be(uhci->regs + reg);
#endif
else
return readw(uhci->regs + reg);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| jan andersson | jan andersson | 67 | 100.00% | 2 | 100.00% |
| Total | 67 | 100.00% | 2 | 100.00% |
static inline void uhci_writew(const struct uhci_hcd *uhci, u16 val, int reg)
{
if (uhci_has_pci_registers(uhci))
outw(val, uhci->io_addr + reg);
#ifdef CONFIG_USB_UHCI_BIG_ENDIAN_MMIO
else if (uhci_big_endian_mmio(uhci))
writew_be(val, uhci->regs + reg);
#endif
else
writew(val, uhci->regs + reg);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| jan andersson | jan andersson | 73 | 100.00% | 2 | 100.00% |
| Total | 73 | 100.00% | 2 | 100.00% |
static inline u8 uhci_readb(const struct uhci_hcd *uhci, int reg)
{
if (uhci_has_pci_registers(uhci))
return inb(uhci->io_addr + reg);
#ifdef CONFIG_USB_UHCI_BIG_ENDIAN_MMIO
else if (uhci_big_endian_mmio(uhci))
return readb_be(uhci->regs + reg);
#endif
else
return readb(uhci->regs + reg);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| jan andersson | jan andersson | 67 | 100.00% | 2 | 100.00% |
| Total | 67 | 100.00% | 2 | 100.00% |
static inline void uhci_writeb(const struct uhci_hcd *uhci, u8 val, int reg)
{
if (uhci_has_pci_registers(uhci))
outb(val, uhci->io_addr + reg);
#ifdef CONFIG_USB_UHCI_BIG_ENDIAN_MMIO
else if (uhci_big_endian_mmio(uhci))
writeb_be(val, uhci->regs + reg);
#endif
else
writeb(val, uhci->regs + reg);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| jan andersson | jan andersson | 73 | 100.00% | 2 | 100.00% |
| Total | 73 | 100.00% | 2 | 100.00% |
#endif /* CONFIG_USB_UHCI_SUPPORT_NON_PCI_HC */
/*
* The GRLIB GRUSBHC controller can use big endian format for its descriptors.
*
* UHCI controllers accessed through PCI work normally (little-endian
* everywhere), so we don't bother supporting a BE-only mode.
*/
#ifdef CONFIG_USB_UHCI_BIG_ENDIAN_DESC
#define uhci_big_endian_desc(u) ((u)->big_endian_desc)
/* cpu to uhci */
static inline __hc32 cpu_to_hc32(const struct uhci_hcd *uhci, const u32 x)
{
return uhci_big_endian_desc(uhci)
? (__force __hc32)cpu_to_be32(x)
: (__force __hc32)cpu_to_le32(x);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| jan andersson | jan andersson | 41 | 100.00% | 1 | 100.00% |
| Total | 41 | 100.00% | 1 | 100.00% |
/* uhci to cpu */
static inline u32 hc32_to_cpu(const struct uhci_hcd *uhci, const __hc32 x)
{
return uhci_big_endian_desc(uhci)
? be32_to_cpu((__force __be32)x)
: le32_to_cpu((__force __le32)x);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| jan andersson | jan andersson | 41 | 100.00% | 1 | 100.00% |
| Total | 41 | 100.00% | 1 | 100.00% |
#else
/* cpu to uhci */
static inline __hc32 cpu_to_hc32(const struct uhci_hcd *uhci, const u32 x)
{
return cpu_to_le32(x);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| jan andersson | jan andersson | 23 | 100.00% | 1 | 100.00% |
| Total | 23 | 100.00% | 1 | 100.00% |
/* uhci to cpu */
static inline u32 hc32_to_cpu(const struct uhci_hcd *uhci, const __hc32 x)
{
return le32_to_cpu(x);
}
Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| jan andersson | jan andersson | 23 | 100.00% | 1 | 100.00% |
| Total | 23 | 100.00% | 1 | 100.00% |
#endif
#endif
Overall Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| jan andersson | jan andersson | 955 | 45.78% | 6 | 11.54% |
| johannes erdfelt | johannes erdfelt | 555 | 26.61% | 2 | 3.85% |
| alan stern | alan stern | 554 | 26.56% | 38 | 73.08% |
| david brownell | david brownell | 15 | 0.72% | 2 | 3.85% |
| greg kroah-hartman | greg kroah-hartman | 4 | 0.19% | 2 | 3.85% |
| deepak saxena | deepak saxena | 2 | 0.10% | 1 | 1.92% |
| david s. miller | david s. miller | 1 | 0.05% | 1 | 1.92% |
| Total | 2086 | 100.00% | 52 | 100.00% |
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.