Release 4.7 drivers/usb/serial/keyspan_usa26msg.h
/*
usa26msg.h
Copyright (C) 1998-2000 InnoSys Incorporated. All Rights Reserved
This file is available under a BSD-style copyright
Keyspan USB Async Message Formats for the USA28X
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are
met:
1. Redistributions of source code must retain this licence text
without modification, this list of conditions, and the following
disclaimer. The following copyright notice must appear immediately at
the beginning of all source files:
Copyright (C) 1998-2000 InnoSys Incorporated. All Rights Reserved
This file is available under a BSD-style copyright
2. The name of InnoSys Incorporated may not be used to endorse or promote
products derived from this software without specific prior written
permission.
THIS SOFTWARE IS PROVIDED BY INNOSYS CORP. ``AS IS'' AND ANY EXPRESS OR
IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGE.
Third revision: USA28X version (aka USA26)
Buffer formats for RX/TX data messages are not defined by
a structure, but are described here:
USB OUT (host -> USAxx, transmit) messages contain a
REQUEST_ACK indicator (set to 0xff to request an ACK at the
completion of transmit; 0x00 otherwise), followed by data:
RQSTACK DAT DAT DAT ...
with a total data length of 63.
USB IN (USAxx -> host, receive) messages begin with a status
byte in which the 0x80 bit is either:
(a) 0x80 bit clear
indicates that the bytes following it are all data
bytes:
STAT DATA DATA DATA DATA DATA ...
for a total of up to 63 DATA bytes,
or:
(b) 0x80 bit set
indicates that the bytes following alternate data and
status bytes:
STAT DATA STAT DATA STAT DATA STAT DATA ...
for a total of up to 32 DATA bytes.
The valid bits in the STAT bytes are:
OVERRUN 0x02
PARITY 0x04
FRAMING 0x08
BREAK 0x10
Notes:
(1) The OVERRUN bit can appear in either (a) or (b) format
messages, but the but the PARITY/FRAMING/BREAK bits
only appear in (b) format messages.
(2) For the host to determine the exact point at which the
overrun occurred (to identify the point in the data
stream at which the data was lost), it needs to count
128 characters, starting at the first character of the
message in which OVERRUN was reported; the lost character(s)
would have been received between the 128th and 129th
characters.
(3) An RX data message in which the first byte has 0x80 clear
serves as a "break off" indicator.
revision history:
1999feb10 add reportHskiaChanges to allow us to ignore them
1999feb10 add txAckThreshold for fast+loose throughput enhancement
1999mar30 beef up support for RX error reporting
1999apr14 add resetDataToggle to control message
2000jan04 merge with usa17msg.h
2000jun01 add extended BSD-style copyright text
2001jul05 change message format to improve OVERRUN case
Note on shared names:
In the case of fields which have been merged between the USA17
and USA26 definitions, the USA26 definition is the first part
of the name and the USA17 definition is the second part of the
name; both meanings are described below.
*/
#ifndef __USA26MSG__
#define __USA26MSG__
struct keyspan_usa26_portControlMessage
{
/*
there are three types of "commands" sent in the control message:
1. configuration changes which must be requested by setting
the corresponding "set" flag (and should only be requested
when necessary, to reduce overhead on the USA26):
*/
u8 setClocking, // BOTH: host requests baud rate be set
baudLo, // BOTH: host does baud divisor calculation
baudHi, // BOTH: baudHi is only used for first port (gives lower rates)
externalClock_txClocking,
// USA26: 0=internal, other=external
// USA17: 0=internal, other=external/RI
rxClocking, // USA17: 0=internal, 1=external/RI, other=external/DSR
setLcr, // BOTH: host requests lcr be set
lcr, // BOTH: use PARITY, STOPBITS, DATABITS below
setFlowControl, // BOTH: host requests flow control be set
ctsFlowControl, // BOTH: 1=use CTS flow control, 0=don't
xonFlowControl, // BOTH: 1=use XON/XOFF flow control, 0=don't
xonChar, // BOTH: specified in current character format
xoffChar, // BOTH: specified in current character format
setTxTriState_setRts,
// USA26: host requests TX tri-state be set
// USA17: host requests RTS output be set
txTriState_rts, // BOTH: 1=active (normal), 0=tristate (off)
setHskoa_setDtr,
// USA26: host requests HSKOA output be set
// USA17: host requests DTR output be set
hskoa_dtr, // BOTH: 1=on, 0=off
setPrescaler, // USA26: host requests prescalar be set (default: 13)
prescaler; // BOTH: specified as N/8; values 8-ff are valid
// must be set any time internal baud rate is set;
// must not be set when external clocking is used
// note: in USA17, prescaler is applied whenever
// setClocking is requested
/*
3. configuration data which is simply used as is (no overhead,
but must be specified correctly in every host message).
*/
u8 forwardingLength, // BOTH: forward when this number of chars available
reportHskiaChanges_dsrFlowControl,
// USA26: 1=normal; 0=ignore external clock
// USA17: 1=use DSR flow control, 0=don't
txAckThreshold, // BOTH: 0=not allowed, 1=normal, 2-255 deliver ACK faster
loopbackMode; // BOTH: 0=no loopback, 1=loopback enabled
/*
4. commands which are flags only; these are processed in order
(so that, e.g., if both _txOn and _txOff flags are set, the
port ends in a TX_OFF state); any non-zero value is respected
*/
u8 _txOn, // BOTH: enable transmitting (and continue if there's data)
_txOff, // BOTH: stop transmitting
txFlush, // BOTH: toss outbound data
txBreak, // BOTH: turn on break (cleared by _txOn)
rxOn, // BOTH: turn on receiver
rxOff, // BOTH: turn off receiver
rxFlush, // BOTH: toss inbound data
rxForward, // BOTH: forward all inbound data, NOW (as if fwdLen==1)
returnStatus, // BOTH: return current status (even if it hasn't changed)
resetDataToggle;// BOTH: reset data toggle state to DATA0
};
// defines for bits in lcr
#define USA_DATABITS_5 0x00
#define USA_DATABITS_6 0x01
#define USA_DATABITS_7 0x02
#define USA_DATABITS_8 0x03
#define STOPBITS_5678_1 0x00
// 1 stop bit for all byte sizes
#define STOPBITS_5_1p5 0x04
// 1.5 stop bits for 5-bit byte
#define STOPBITS_678_2 0x04
// 2 stop bits for 6/7/8-bit byte
#define USA_PARITY_NONE 0x00
#define USA_PARITY_ODD 0x08
#define USA_PARITY_EVEN 0x18
#define PARITY_1 0x28
#define PARITY_0 0x38
// all things called "StatusMessage" are sent on the status endpoint
struct keyspan_usa26_portStatusMessage // one for each port
{
u8 port, // BOTH: 0=first, 1=second, other=see below
hskia_cts, // USA26: reports HSKIA pin
// USA17: reports CTS pin
gpia_dcd, // USA26: reports GPIA pin
// USA17: reports DCD pin
dsr, // USA17: reports DSR pin
ri, // USA17: reports RI pin
_txOff, // port has been disabled (by host)
_txXoff, // port is in XOFF state (either host or RX XOFF)
rxEnabled, // as configured by rxOn/rxOff 1=on, 0=off
controlResponse;// 1=a control message has been processed
};
// bits in RX data message when STAT byte is included
#define RXERROR_OVERRUN 0x02
#define RXERROR_PARITY 0x04
#define RXERROR_FRAMING 0x08
#define RXERROR_BREAK 0x10
struct keyspan_usa26_globalControlMessage
{
u8 sendGlobalStatus, // 2=request for two status responses
resetStatusToggle, // 1=reset global status toggle
resetStatusCount; // a cycling value
};
struct keyspan_usa26_globalStatusMessage
{
u8 port, // 3
sendGlobalStatus, // from request, decremented
resetStatusCount; // as in request
};
struct keyspan_usa26_globalDebugMessage
{
u8 port, // 2
a,
b,
c,
d;
};
// ie: the maximum length of an EZUSB endpoint buffer
#define MAX_DATA_LEN 64
// update status approx. 60 times a second (16.6666 ms)
#define STATUS_UPDATE_INTERVAL 16
// status rationing tuning value (each port gets checked each n ms)
#define STATUS_RATION 10
#endif
Overall Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| pre-git | pre-git | 286 | 97.95% | 2 | 50.00% |
| greg kroah-hartman | greg kroah-hartman | 5 | 1.71% | 1 | 25.00% |
| rahul bedarkar | rahul bedarkar | 1 | 0.34% | 1 | 25.00% |
| Total | 292 | 100.00% | 4 | 100.00% |
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.