Release 4.7 include/linux/ethtool.h

/*
 * ethtool.h: Defines for Linux ethtool.
 *
 * Copyright (C) 1998 David S. Miller (davem@redhat.com)
 * Copyright 2001 Jeff Garzik <jgarzik@pobox.com>
 * Portions Copyright 2001 Sun Microsystems (thockin@sun.com)
 * Portions Copyright 2002 Intel (eli.kupermann@intel.com,
 *                                christopher.leech@intel.com,
 *                                scott.feldman@intel.com)
 * Portions Copyright (C) Sun Microsystems 2008
 */
#ifndef _LINUX_ETHTOOL_H

#define _LINUX_ETHTOOL_H

#include <linux/bitmap.h>
#include <linux/compat.h>
#include <uapi/linux/ethtool.h>

#ifdef CONFIG_COMPAT


struct compat_ethtool_rx_flow_spec {
	
u32		flow_type;
	
union ethtool_flow_union h_u;
	
struct ethtool_flow_ext h_ext;
	
union ethtool_flow_union m_u;
	
struct ethtool_flow_ext m_ext;
	
compat_u64	ring_cookie;
	
u32		location;
};


struct compat_ethtool_rxnfc {
	
u32				cmd;
	
u32				flow_type;
	
compat_u64			data;
	
struct compat_ethtool_rx_flow_spec fs;
	
u32				rule_cnt;
	
u32				rule_locs[0];
};

#endif /* CONFIG_COMPAT */

#include <linux/rculist.h>

/**
 * enum ethtool_phys_id_state - indicator state for physical identification
 * @ETHTOOL_ID_INACTIVE: Physical ID indicator should be deactivated
 * @ETHTOOL_ID_ACTIVE: Physical ID indicator should be activated
 * @ETHTOOL_ID_ON: LED should be turned on (used iff %ETHTOOL_ID_ACTIVE
 *      is not supported)
 * @ETHTOOL_ID_OFF: LED should be turned off (used iff %ETHTOOL_ID_ACTIVE
 *      is not supported)
 */

enum ethtool_phys_id_state {
	
ETHTOOL_ID_INACTIVE,
	
ETHTOOL_ID_ACTIVE,
	
ETHTOOL_ID_ON,
	
ETHTOOL_ID_OFF
};

enum {
	
ETH_RSS_HASH_TOP_BIT, /* Configurable RSS hash function - Toeplitz */
	
ETH_RSS_HASH_XOR_BIT, /* Configurable RSS hash function - Xor */

	/*
         * Add your fresh new hash function bits above and remember to update
         * rss_hash_func_strings[] in ethtool.c
         */
	
ETH_RSS_HASH_FUNCS_COUNT
};


#define __ETH_RSS_HASH_BIT(bit)	((u32)1 << (bit))

#define __ETH_RSS_HASH(name)	__ETH_RSS_HASH_BIT(ETH_RSS_HASH_##name##_BIT)


#define ETH_RSS_HASH_TOP	__ETH_RSS_HASH(TOP)

#define ETH_RSS_HASH_XOR	__ETH_RSS_HASH(XOR)


#define ETH_RSS_HASH_UNKNOWN	0

#define ETH_RSS_HASH_NO_CHANGE	0

struct net_device;

/* Some generic methods drivers may use in their ethtool_ops */
u32 ethtool_op_get_link(struct net_device *dev);
int ethtool_op_get_ts_info(struct net_device *dev, struct ethtool_ts_info *eti);

/**
 * ethtool_rxfh_indir_default - get default value for RX flow hash indirection
 * @index: Index in RX flow hash indirection table
 * @n_rx_rings: Number of RX rings to use
 *
 * This function provides the default policy for RX flow hash indirection.
 */


static inline u32 ethtool_rxfh_indir_default(u32 index, u32 n_rx_rings)
{
	return index % n_rx_rings;
}

Contributors
Person
Tokens
Prop
Commits
CommitProp
david howells
david howells
10
55.56%
1
50.00%
brandon philips
brandon philips
8
44.44%
1
50.00%
Total
18
100.00%
2
100.00%

/* number of link mode bits/ulongs handled internally by kernel */

#define __ETHTOOL_LINK_MODE_MASK_NBITS			\
	(__ETHTOOL_LINK_MODE_LAST + 1)

/* declare a link mode bitmap */

#define __ETHTOOL_DECLARE_LINK_MODE_MASK(name)		\
	DECLARE_BITMAP(name, __ETHTOOL_LINK_MODE_MASK_NBITS)

/* drivers must ignore base.cmd and base.link_mode_masks_nwords
 * fields, but they are allowed to overwrite them (will be ignored).
 */

struct ethtool_link_ksettings {
	
struct ethtool_link_settings base;
	struct {
		__ETHTOOL_DECLARE_LINK_MODE_MASK(supported);
		__ETHTOOL_DECLARE_LINK_MODE_MASK(advertising);
		__ETHTOOL_DECLARE_LINK_MODE_MASK(lp_advertising);
	} 
link_modes;
};

/**
 * ethtool_link_ksettings_zero_link_mode - clear link_ksettings link mode mask
 *   @ptr : pointer to struct ethtool_link_ksettings
 *   @name : one of supported/advertising/lp_advertising
 */

#define ethtool_link_ksettings_zero_link_mode(ptr, name)		\
	bitmap_zero((ptr)->link_modes.name, __ETHTOOL_LINK_MODE_MASK_NBITS)

/**
 * ethtool_link_ksettings_add_link_mode - set bit in link_ksettings
 * link mode mask
 *   @ptr : pointer to struct ethtool_link_ksettings
 *   @name : one of supported/advertising/lp_advertising
 *   @mode : one of the ETHTOOL_LINK_MODE_*_BIT
 * (not atomic, no bound checking)
 */

#define ethtool_link_ksettings_add_link_mode(ptr, name, mode)		\
	__set_bit(ETHTOOL_LINK_MODE_ ## mode ## _BIT, (ptr)->link_modes.name)

/**
 * ethtool_link_ksettings_test_link_mode - test bit in ksettings link mode mask
 *   @ptr : pointer to struct ethtool_link_ksettings
 *   @name : one of supported/advertising/lp_advertising
 *   @mode : one of the ETHTOOL_LINK_MODE_*_BIT
 * (not atomic, no bound checking)
 *
 * Returns true/false.
 */

#define ethtool_link_ksettings_test_link_mode(ptr, name, mode)		\
	test_bit(ETHTOOL_LINK_MODE_ ## mode ## _BIT, (ptr)->link_modes.name)

extern int
__ethtool_get_link_ksettings(struct net_device *dev,
			     struct ethtool_link_ksettings *link_ksettings);

void ethtool_convert_legacy_u32_to_link_mode(unsigned long *dst,
					     u32 legacy_u32);

/* return false if src had higher bits set. lower bits always updated. */
bool ethtool_convert_link_mode_to_legacy_u32(u32 *legacy_u32,
				     const unsigned long *src);

/**
 * struct ethtool_ops - optional netdev operations
 * @get_settings: DEPRECATED, use %get_link_ksettings/%set_link_ksettings
 *      API. Get various device settings including Ethernet link
 *      settings. The @cmd parameter is expected to have been cleared
 *      before get_settings is called. Returns a negative error code
 *      or zero.
 * @set_settings: DEPRECATED, use %get_link_ksettings/%set_link_ksettings
 *      API. Set various device settings including Ethernet link
 *      settings.  Returns a negative error code or zero.
 * @get_drvinfo: Report driver/device information.  Should only set the
 *      @driver, @version, @fw_version and @bus_info fields.  If not
 *      implemented, the @driver and @bus_info fields will be filled in
 *      according to the netdev's parent device.
 * @get_regs_len: Get buffer length required for @get_regs
 * @get_regs: Get device registers
 * @get_wol: Report whether Wake-on-Lan is enabled
 * @set_wol: Turn Wake-on-Lan on or off.  Returns a negative error code
 *      or zero.
 * @get_msglevel: Report driver message level.  This should be the value
 *      of the @msg_enable field used by netif logging functions.
 * @set_msglevel: Set driver message level
 * @nway_reset: Restart autonegotiation.  Returns a negative error code
 *      or zero.
 * @get_link: Report whether physical link is up.  Will only be called if
 *      the netdev is up.  Should usually be set to ethtool_op_get_link(),
 *      which uses netif_carrier_ok().
 * @get_eeprom: Read data from the device EEPROM.
 *      Should fill in the magic field.  Don't need to check len for zero
 *      or wraparound.  Fill in the data argument with the eeprom values
 *      from offset to offset + len.  Update len to the amount read.
 *      Returns an error or zero.
 * @set_eeprom: Write data to the device EEPROM.
 *      Should validate the magic field.  Don't need to check len for zero
 *      or wraparound.  Update len to the amount written.  Returns an error
 *      or zero.
 * @get_coalesce: Get interrupt coalescing parameters.  Returns a negative
 *      error code or zero.
 * @set_coalesce: Set interrupt coalescing parameters.  Returns a negative
 *      error code or zero.
 * @get_ringparam: Report ring sizes
 * @set_ringparam: Set ring sizes.  Returns a negative error code or zero.
 * @get_pauseparam: Report pause parameters
 * @set_pauseparam: Set pause parameters.  Returns a negative error code
 *      or zero.
 * @self_test: Run specified self-tests
 * @get_strings: Return a set of strings that describe the requested objects
 * @set_phys_id: Identify the physical devices, e.g. by flashing an LED
 *      attached to it.  The implementation may update the indicator
 *      asynchronously or synchronously, but in either case it must return
 *      quickly.  It is initially called with the argument %ETHTOOL_ID_ACTIVE,
 *      and must either activate asynchronous updates and return zero, return
 *      a negative error or return a positive frequency for synchronous
 *      indication (e.g. 1 for one on/off cycle per second).  If it returns
 *      a frequency then it will be called again at intervals with the
 *      argument %ETHTOOL_ID_ON or %ETHTOOL_ID_OFF and should set the state of
 *      the indicator accordingly.  Finally, it is called with the argument
 *      %ETHTOOL_ID_INACTIVE and must deactivate the indicator.  Returns a
 *      negative error code or zero.
 * @get_ethtool_stats: Return extended statistics about the device.
 *      This is only useful if the device maintains statistics not
 *      included in &struct rtnl_link_stats64.
 * @begin: Function to be called before any other operation.  Returns a
 *      negative error code or zero.
 * @complete: Function to be called after any other operation except
 *      @begin.  Will be called even if the other operation failed.
 * @get_priv_flags: Report driver-specific feature flags.
 * @set_priv_flags: Set driver-specific feature flags.  Returns a negative
 *      error code or zero.
 * @get_sset_count: Get number of strings that @get_strings will write.
 * @get_rxnfc: Get RX flow classification rules.  Returns a negative
 *      error code or zero.
 * @set_rxnfc: Set RX flow classification rules.  Returns a negative
 *      error code or zero.
 * @flash_device: Write a firmware image to device's flash memory.
 *      Returns a negative error code or zero.
 * @reset: Reset (part of) the device, as specified by a bitmask of
 *      flags from &enum ethtool_reset_flags.  Returns a negative
 *      error code or zero.
 * @get_rxfh_key_size: Get the size of the RX flow hash key.
 *      Returns zero if not supported for this specific device.
 * @get_rxfh_indir_size: Get the size of the RX flow hash indirection table.
 *      Returns zero if not supported for this specific device.
 * @get_rxfh: Get the contents of the RX flow hash indirection table, hash key
 *      and/or hash function.
 *      Returns a negative error code or zero.
 * @set_rxfh: Set the contents of the RX flow hash indirection table, hash
 *      key, and/or hash function.  Arguments which are set to %NULL or zero
 *      will remain unchanged.
 *      Returns a negative error code or zero. An error code must be returned
 *      if at least one unsupported change was requested.
 * @get_channels: Get number of channels.
 * @set_channels: Set number of channels.  Returns a negative error code or
 *      zero.
 * @get_dump_flag: Get dump flag indicating current dump length, version,
 *                 and flag of the device.
 * @get_dump_data: Get dump data.
 * @set_dump: Set dump specific flags to the device.
 * @get_ts_info: Get the time stamping and PTP hardware clock capabilities.
 *      Drivers supporting transmit time stamps in software should set this to
 *      ethtool_op_get_ts_info().
 * @get_module_info: Get the size and type of the eeprom contained within
 *      a plug-in module.
 * @get_module_eeprom: Get the eeprom information from the plug-in module
 * @get_eee: Get Energy-Efficient (EEE) supported and status.
 * @set_eee: Set EEE status (enable/disable) as well as LPI timers.
 * @get_per_queue_coalesce: Get interrupt coalescing parameters per queue.
 *      It must check that the given queue number is valid. If neither a RX nor
 *      a TX queue has this number, return -EINVAL. If only a RX queue or a TX
 *      queue has this number, set the inapplicable fields to ~0 and return 0.
 *      Returns a negative error code or zero.
 * @set_per_queue_coalesce: Set interrupt coalescing parameters per queue.
 *      It must check that the given queue number is valid. If neither a RX nor
 *      a TX queue has this number, return -EINVAL. If only a RX queue or a TX
 *      queue has this number, ignore the inapplicable fields.
 *      Returns a negative error code or zero.
 * @get_link_ksettings: When defined, takes precedence over the
 *      %get_settings method. Get various device settings
 *      including Ethernet link settings. The %cmd and
 *      %link_mode_masks_nwords fields should be ignored (use
 *      %__ETHTOOL_LINK_MODE_MASK_NBITS instead of the latter), any
 *      change to them will be overwritten by kernel. Returns a
 *      negative error code or zero.
 * @set_link_ksettings: When defined, takes precedence over the
 *      %set_settings method. Set various device settings including
 *      Ethernet link settings. The %cmd and %link_mode_masks_nwords
 *      fields should be ignored (use %__ETHTOOL_LINK_MODE_MASK_NBITS
 *      instead of the latter), any change to them will be overwritten
 *      by kernel. Returns a negative error code or zero.
 *
 * All operations are optional (i.e. the function pointer may be set
 * to %NULL) and callers must take this into account.  Callers must
 * hold the RTNL lock.
 *
 * See the structures used by these operations for further documentation.
 * Note that for all operations using a structure ending with a zero-
 * length array, the array is allocated separately in the kernel and
 * is passed to the driver as an additional parameter.
 *
 * See &struct net_device and &struct net_device_ops for documentation
 * of the generic netdev features interface.
 */

struct ethtool_ops {
	
int	(*get_settings)(struct net_device *, struct ethtool_cmd *);
	
int	(*set_settings)(struct net_device *, struct ethtool_cmd *);
	
void	(*get_drvinfo)(struct net_device *, struct ethtool_drvinfo *);
	
int	(*get_regs_len)(struct net_device *);
	
void	(*get_regs)(struct net_device *, struct ethtool_regs *, void *);
	
void	(*get_wol)(struct net_device *, struct ethtool_wolinfo *);
	
int	(*set_wol)(struct net_device *, struct ethtool_wolinfo *);
	
u32	(*get_msglevel)(struct net_device *);
	
void	(*set_msglevel)(struct net_device *, u32);
	
int	(*nway_reset)(struct net_device *);
	
u32	(*get_link)(struct net_device *);
	
int	(*get_eeprom_len)(struct net_device *);
	
int	(*get_eeprom)(struct net_device *,
			      struct ethtool_eeprom *, u8 *);
	
int	(*set_eeprom)(struct net_device *,
			      struct ethtool_eeprom *, u8 *);
	
int	(*get_coalesce)(struct net_device *, struct ethtool_coalesce *);
	
int	(*set_coalesce)(struct net_device *, struct ethtool_coalesce *);
	
void	(*get_ringparam)(struct net_device *,
				 struct ethtool_ringparam *);
	
int	(*set_ringparam)(struct net_device *,
				 struct ethtool_ringparam *);
	
void	(*get_pauseparam)(struct net_device *,
				  struct ethtool_pauseparam*);
	
int	(*set_pauseparam)(struct net_device *,
				  struct ethtool_pauseparam*);
	
void	(*self_test)(struct net_device *, struct ethtool_test *, u64 *);
	
void	(*get_strings)(struct net_device *, u32 stringset, u8 *);
	
int	(*set_phys_id)(struct net_device *, enum ethtool_phys_id_state);
	
void	(*get_ethtool_stats)(struct net_device *,
				     struct ethtool_stats *, u64 *);
	
int	(*begin)(struct net_device *);
	
void	(*complete)(struct net_device *);
	
u32	(*get_priv_flags)(struct net_device *);
	
int	(*set_priv_flags)(struct net_device *, u32);
	
int	(*get_sset_count)(struct net_device *, int);
	
int	(*get_rxnfc)(struct net_device *,
			     struct ethtool_rxnfc *, u32 *rule_locs);
	
int	(*set_rxnfc)(struct net_device *, struct ethtool_rxnfc *);
	
int	(*flash_device)(struct net_device *, struct ethtool_flash *);
	
int	(*reset)(struct net_device *, u32 *);
	
u32	(*get_rxfh_key_size)(struct net_device *);
	
u32	(*get_rxfh_indir_size)(struct net_device *);
	
int	(*get_rxfh)(struct net_device *, u32 *indir, u8 *key,
			    u8 *hfunc);
	
int	(*set_rxfh)(struct net_device *, const u32 *indir,
			    const u8 *key, const u8 hfunc);
	
void	(*get_channels)(struct net_device *, struct ethtool_channels *);
	
int	(*set_channels)(struct net_device *, struct ethtool_channels *);
	
int	(*get_dump_flag)(struct net_device *, struct ethtool_dump *);
	
int	(*get_dump_data)(struct net_device *,
				 struct ethtool_dump *, void *);
	
int	(*set_dump)(struct net_device *, struct ethtool_dump *);
	
int	(*get_ts_info)(struct net_device *, struct ethtool_ts_info *);
	
int     (*get_module_info)(struct net_device *,
				   struct ethtool_modinfo *);
	
int     (*get_module_eeprom)(struct net_device *,
				     struct ethtool_eeprom *, u8 *);
	
int	(*get_eee)(struct net_device *, struct ethtool_eee *);
	
int	(*set_eee)(struct net_device *, struct ethtool_eee *);
	
int	(*get_tunable)(struct net_device *,
			       const struct ethtool_tunable *, void *);
	
int	(*set_tunable)(struct net_device *,
			       const struct ethtool_tunable *, const void *);
	
int	(*get_per_queue_coalesce)(struct net_device *, u32,
					  struct ethtool_coalesce *);
	
int	(*set_per_queue_coalesce)(struct net_device *, u32,
					  struct ethtool_coalesce *);
	
int	(*get_link_ksettings)(struct net_device *,
				      struct ethtool_link_ksettings *);
	
int	(*set_link_ksettings)(struct net_device *,
				      const struct ethtool_link_ksettings *);
};
#endif /* _LINUX_ETHTOOL_H */
Overall Contributors
Person
Tokens
Prop
Commits
CommitProp
david howells
david howells
584
52.05%
1
3.45%
david decotigny
david decotigny
132
11.76%
1
3.45%
jeff garzik
jeff garzik
124
11.05%
2
6.90%
eyal perry
eyal perry
50
4.46%
1
3.45%
venkat duvvuru
venkat duvvuru
45
4.01%
1
3.45%
govindarajulu varadarajan
govindarajulu varadarajan
39
3.48%
1
3.45%
kan liang
kan liang
34
3.03%
2
6.90%
philippe reynes
philippe reynes
27
2.41%
1
3.45%
pre-git
pre-git
23
2.05%
2
6.90%
ben hutchings
ben hutchings
19
1.69%
6
20.69%
brandon philips
brandon philips
12
1.07%
1
3.45%
scott feldman
scott feldman
10
0.89%
1
3.45%
peter p waskiewicz
peter p waskiewicz
7
0.62%
1
3.45%
santwona behera
santwona behera
6
0.53%
1
3.45%
linus torvalds
linus torvalds
4
0.36%
3
10.34%
michal miroslaw
michal miroslaw
2
0.18%
1
3.45%
alexander duyck
alexander duyck
2
0.18%
1
3.45%
chaitanya lala
chaitanya lala
1
0.09%
1
3.45%
ajit khaparde
ajit khaparde
1
0.09%
1
3.45%
Total
1122
100.00%
29
100.00%
  
Directory: include/linux

Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.