Release 4.7 include/uapi/linux/lp.h
/*
* usr/include/linux/lp.h c.1991-1992 James Wiegand
* many modifications copyright (C) 1992 Michael K. Johnson
* Interrupt support added 1993 Nigel Gamble
* Removed 8255 status defines from inside __KERNEL__ Marcelo Tosatti
*/
#ifndef _UAPI_LINUX_LP_H
#define _UAPI_LINUX_LP_H
/*
* Per POSIX guidelines, this module reserves the LP and lp prefixes
* These are the lp_table[minor].flags flags...
*/
#define LP_EXIST 0x0001
#define LP_SELEC 0x0002
#define LP_BUSY 0x0004
#define LP_BUSY_BIT_POS 2
#define LP_OFFL 0x0008
#define LP_NOPA 0x0010
#define LP_ERR 0x0020
#define LP_ABORT 0x0040
#define LP_CAREFUL 0x0080
/* obsoleted -arca */
#define LP_ABORTOPEN 0x0100
#define LP_TRUST_IRQ_ 0x0200
/* obsolete */
#define LP_NO_REVERSE 0x0400
/* No reverse mode available. */
#define LP_DATA_AVAIL 0x0800
/* Data is available. */
/*
* bit defines for 8255 status port
* base + 1
* accessed with LP_S(minor), which gets the byte...
*/
#define LP_PBUSY 0x80
/* inverted input, active high */
#define LP_PACK 0x40
/* unchanged input, active low */
#define LP_POUTPA 0x20
/* unchanged input, active high */
#define LP_PSELECD 0x10
/* unchanged input, active high */
#define LP_PERRORP 0x08
/* unchanged input, active low */
/* timeout for each character. This is relative to bus cycles -- it
* is the count in a busy loop. THIS IS THE VALUE TO CHANGE if you
* have extremely slow printing, or if the machine seems to slow down
* a lot when you print. If you have slow printing, increase this
* number and recompile, and if your system gets bogged down, decrease
* this number. This can be changed with the tunelp(8) command as well.
*/
#define LP_INIT_CHAR 1000
/* The parallel port specs apparently say that there needs to be
* a .5usec wait before and after the strobe.
*/
#define LP_INIT_WAIT 1
/* This is the amount of time that the driver waits for the printer to
* catch up when the printer's buffer appears to be filled. If you
* want to tune this and have a fast printer (i.e. HPIIIP), decrease
* this number, and if you have a slow printer, increase this number.
* This is in hundredths of a second, the default 2 being .05 second.
* Or use the tunelp(8) command, which is especially nice if you want
* change back and forth between character and graphics printing, which
* are wildly different...
*/
#define LP_INIT_TIME 2
/* IOCTL numbers */
#define LPCHAR 0x0601
/* corresponds to LP_INIT_CHAR */
#define LPTIME 0x0602
/* corresponds to LP_INIT_TIME */
#define LPABORT 0x0604
/* call with TRUE arg to abort on error,
FALSE to retry. Default is retry. */
#define LPSETIRQ 0x0605
/* call with new IRQ number,
or 0 for polling (no IRQ) */
#define LPGETIRQ 0x0606
/* get the current IRQ number */
#define LPWAIT 0x0608
/* corresponds to LP_INIT_WAIT */
/* NOTE: LPCAREFUL is obsoleted and it' s always the default right now -arca */
#define LPCAREFUL 0x0609
/* call with TRUE arg to require out-of-paper, off-
line, and error indicators good on all writes,
FALSE to ignore them. Default is ignore. */
#define LPABORTOPEN 0x060a
/* call with TRUE arg to abort open() on error,
FALSE to ignore error. Default is ignore. */
#define LPGETSTATUS 0x060b
/* return LP_S(minor) */
#define LPRESET 0x060c
/* reset printer */
#ifdef LP_STATS
#define LPGETSTATS 0x060d
/* get statistics (struct lp_stats) */
#endif
#define LPGETFLAGS 0x060e
/* get status flags */
#define LPSETTIMEOUT 0x060f
/* set parport timeout */
/* timeout for printk'ing a timeout, in jiffies (100ths of a second).
This is also used for re-checking error conditions if LP_ABORT is
not set. This is the default behavior. */
#define LP_TIMEOUT_INTERRUPT (60 * HZ)
#define LP_TIMEOUT_POLLED (10 * HZ)
#endif /* _UAPI_LINUX_LP_H */
Overall Contributors
| Person | Tokens | Prop | Commits | CommitProp |
| david howells | david howells | 189 | 100.00% | 1 | 100.00% |
| Total | 189 | 100.00% | 1 | 100.00% |
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.