Contributors: 5
Author Tokens Token Proportion Commits Commit Proportion
M'boumba Cedric Madianga 2936 99.59% 1 20.00%
Pierre-Yves MORDRET 8 0.27% 1 20.00%
Benjamin Gaignard 2 0.07% 1 20.00%
Philipp Zabel 1 0.03% 1 20.00%
Gustavo A. R. Silva 1 0.03% 1 20.00%
Total 2948 5 


// SPDX-License-Identifier: GPL-2.0
/*
 * Driver for STMicroelectronics STM32 I2C controller
 *
 * This I2C controller is described in the STM32F429/439 Soc reference manual.
 * Please see below a link to the documentation:
 * http://www.st.com/resource/en/reference_manual/DM00031020.pdf
 *
 * Copyright (C) M'boumba Cedric Madianga 2016
 * Copyright (C) STMicroelectronics 2017
 * Author: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
 *
 * This driver is based on i2c-st.c
 *
 */

#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/i2c.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/iopoll.h>
#include <linux/module.h>
#include <linux/of_address.h>
#include <linux/of_irq.h>
#include <linux/of.h>
#include <linux/platform_device.h>
#include <linux/reset.h>

#include "i2c-stm32.h"

/* STM32F4 I2C offset registers */
#define STM32F4_I2C_CR1			0x00
#define STM32F4_I2C_CR2			0x04
#define STM32F4_I2C_DR			0x10
#define STM32F4_I2C_SR1			0x14
#define STM32F4_I2C_SR2			0x18
#define STM32F4_I2C_CCR			0x1C
#define STM32F4_I2C_TRISE		0x20
#define STM32F4_I2C_FLTR		0x24

/* STM32F4 I2C control 1*/
#define STM32F4_I2C_CR1_POS		BIT(11)
#define STM32F4_I2C_CR1_ACK		BIT(10)
#define STM32F4_I2C_CR1_STOP		BIT(9)
#define STM32F4_I2C_CR1_START		BIT(8)
#define STM32F4_I2C_CR1_PE		BIT(0)

/* STM32F4 I2C control 2 */
#define STM32F4_I2C_CR2_FREQ_MASK	GENMASK(5, 0)
#define STM32F4_I2C_CR2_FREQ(n)		((n) & STM32F4_I2C_CR2_FREQ_MASK)
#define STM32F4_I2C_CR2_ITBUFEN		BIT(10)
#define STM32F4_I2C_CR2_ITEVTEN		BIT(9)
#define STM32F4_I2C_CR2_ITERREN		BIT(8)
#define STM32F4_I2C_CR2_IRQ_MASK	(STM32F4_I2C_CR2_ITBUFEN | \
					 STM32F4_I2C_CR2_ITEVTEN | \
					 STM32F4_I2C_CR2_ITERREN)

/* STM32F4 I2C Status 1 */
#define STM32F4_I2C_SR1_AF		BIT(10)
#define STM32F4_I2C_SR1_ARLO		BIT(9)
#define STM32F4_I2C_SR1_BERR		BIT(8)
#define STM32F4_I2C_SR1_TXE		BIT(7)
#define STM32F4_I2C_SR1_RXNE		BIT(6)
#define STM32F4_I2C_SR1_BTF		BIT(2)
#define STM32F4_I2C_SR1_ADDR		BIT(1)
#define STM32F4_I2C_SR1_SB		BIT(0)
#define STM32F4_I2C_SR1_ITEVTEN_MASK	(STM32F4_I2C_SR1_BTF | \
					 STM32F4_I2C_SR1_ADDR | \
					 STM32F4_I2C_SR1_SB)
#define STM32F4_I2C_SR1_ITBUFEN_MASK	(STM32F4_I2C_SR1_TXE | \
					 STM32F4_I2C_SR1_RXNE)
#define STM32F4_I2C_SR1_ITERREN_MASK	(STM32F4_I2C_SR1_AF | \
					 STM32F4_I2C_SR1_ARLO | \
					 STM32F4_I2C_SR1_BERR)

/* STM32F4 I2C Status 2 */
#define STM32F4_I2C_SR2_BUSY		BIT(1)

/* STM32F4 I2C Control Clock */
#define STM32F4_I2C_CCR_CCR_MASK	GENMASK(11, 0)
#define STM32F4_I2C_CCR_CCR(n)		((n) & STM32F4_I2C_CCR_CCR_MASK)
#define STM32F4_I2C_CCR_FS		BIT(15)
#define STM32F4_I2C_CCR_DUTY		BIT(14)

/* STM32F4 I2C Trise */
#define STM32F4_I2C_TRISE_VALUE_MASK	GENMASK(5, 0)
#define STM32F4_I2C_TRISE_VALUE(n)	((n) & STM32F4_I2C_TRISE_VALUE_MASK)

#define STM32F4_I2C_MIN_STANDARD_FREQ	2U
#define STM32F4_I2C_MIN_FAST_FREQ	6U
#define STM32F4_I2C_MAX_FREQ		46U
#define HZ_TO_MHZ			1000000

/**
 * struct stm32f4_i2c_msg - client specific data
 * @addr: 8-bit slave addr, including r/w bit
 * @count: number of bytes to be transferred
 * @buf: data buffer
 * @result: result of the transfer
 * @stop: last I2C msg to be sent, i.e. STOP to be generated
 */
struct stm32f4_i2c_msg {
	u8 addr;
	u32 count;
	u8 *buf;
	int result;
	bool stop;
};

/**
 * struct stm32f4_i2c_dev - private data of the controller
 * @adap: I2C adapter for this controller
 * @dev: device for this controller
 * @base: virtual memory area
 * @complete: completion of I2C message
 * @clk: hw i2c clock
 * @speed: I2C clock frequency of the controller. Standard or Fast are supported
 * @parent_rate: I2C clock parent rate in MHz
 * @msg: I2C transfer information
 */
struct stm32f4_i2c_dev {
	struct i2c_adapter adap;
	struct device *dev;
	void __iomem *base;
	struct completion complete;
	struct clk *clk;
	int speed;
	int parent_rate;
	struct stm32f4_i2c_msg msg;
};

static inline void stm32f4_i2c_set_bits(void __iomem *reg, u32 mask)
{
	writel_relaxed(readl_relaxed(reg) | mask, reg);
}

static inline void stm32f4_i2c_clr_bits(void __iomem *reg, u32 mask)
{
	writel_relaxed(readl_relaxed(reg) & ~mask, reg);
}

static void stm32f4_i2c_disable_irq(struct stm32f4_i2c_dev *i2c_dev)
{
	void __iomem *reg = i2c_dev->base + STM32F4_I2C_CR2;

	stm32f4_i2c_clr_bits(reg, STM32F4_I2C_CR2_IRQ_MASK);
}

static int stm32f4_i2c_set_periph_clk_freq(struct stm32f4_i2c_dev *i2c_dev)
{
	u32 freq;
	u32 cr2 = 0;

	i2c_dev->parent_rate = clk_get_rate(i2c_dev->clk);
	freq = DIV_ROUND_UP(i2c_dev->parent_rate, HZ_TO_MHZ);

	if (i2c_dev->speed == STM32_I2C_SPEED_STANDARD) {
		/*
		 * To reach 100 kHz, the parent clk frequency should be between
		 * a minimum value of 2 MHz and a maximum value of 46 MHz due
		 * to hardware limitation
		 */
		if (freq < STM32F4_I2C_MIN_STANDARD_FREQ ||
		    freq > STM32F4_I2C_MAX_FREQ) {
			dev_err(i2c_dev->dev,
				"bad parent clk freq for standard mode\n");
			return -EINVAL;
		}
	} else {
		/*
		 * To be as close as possible to 400 kHz, the parent clk
		 * frequency should be between a minimum value of 6 MHz and a
		 * maximum value of 46 MHz due to hardware limitation
		 */
		if (freq < STM32F4_I2C_MIN_FAST_FREQ ||
		    freq > STM32F4_I2C_MAX_FREQ) {
			dev_err(i2c_dev->dev,
				"bad parent clk freq for fast mode\n");
			return -EINVAL;
		}
	}

	cr2 |= STM32F4_I2C_CR2_FREQ(freq);
	writel_relaxed(cr2, i2c_dev->base + STM32F4_I2C_CR2);

	return 0;
}

static void stm32f4_i2c_set_rise_time(struct stm32f4_i2c_dev *i2c_dev)
{
	u32 freq = DIV_ROUND_UP(i2c_dev->parent_rate, HZ_TO_MHZ);
	u32 trise;

	/*
	 * These bits must be programmed with the maximum SCL rise time given in
	 * the I2C bus specification, incremented by 1.
	 *
	 * In standard mode, the maximum allowed SCL rise time is 1000 ns.
	 * If, in the I2C_CR2 register, the value of FREQ[5:0] bits is equal to
	 * 0x08 so period = 125 ns therefore the TRISE[5:0] bits must be
	 * programmed with 0x9. (1000 ns / 125 ns + 1)
	 * So, for I2C standard mode TRISE = FREQ[5:0] + 1
	 *
	 * In fast mode, the maximum allowed SCL rise time is 300 ns.
	 * If, in the I2C_CR2 register, the value of FREQ[5:0] bits is equal to
	 * 0x08 so period = 125 ns therefore the TRISE[5:0] bits must be
	 * programmed with 0x3. (300 ns / 125 ns + 1)
	 * So, for I2C fast mode TRISE = FREQ[5:0] * 300 / 1000 + 1
	 *
	 * Function stm32f4_i2c_set_periph_clk_freq made sure that parent rate
	 * is not higher than 46 MHz . As a result trise is at most 4 bits wide
	 * and so fits into the TRISE bits [5:0].
	 */
	if (i2c_dev->speed == STM32_I2C_SPEED_STANDARD)
		trise = freq + 1;
	else
		trise = freq * 3 / 10 + 1;

	writel_relaxed(STM32F4_I2C_TRISE_VALUE(trise),
		       i2c_dev->base + STM32F4_I2C_TRISE);
}

static void stm32f4_i2c_set_speed_mode(struct stm32f4_i2c_dev *i2c_dev)
{
	u32 val;
	u32 ccr = 0;

	if (i2c_dev->speed == STM32_I2C_SPEED_STANDARD) {
		/*
		 * In standard mode:
		 * t_scl_high = t_scl_low = CCR * I2C parent clk period
		 * So to reach 100 kHz, we have:
		 * CCR = I2C parent rate / 100 kHz >> 1
		 *
		 * For example with parent rate = 2 MHz:
		 * CCR = 2000000 / (100000 << 1) = 10
		 * t_scl_high = t_scl_low = 10 * (1 / 2000000) = 5000 ns
		 * t_scl_high + t_scl_low = 10000 ns so 100 kHz is reached
		 *
		 * Function stm32f4_i2c_set_periph_clk_freq made sure that
		 * parent rate is not higher than 46 MHz . As a result val
		 * is at most 8 bits wide and so fits into the CCR bits [11:0].
		 */
		val = i2c_dev->parent_rate / (100000 << 1);
	} else {
		/*
		 * In fast mode, we compute CCR with duty = 0 as with low
		 * frequencies we are not able to reach 400 kHz.
		 * In that case:
		 * t_scl_high = CCR * I2C parent clk period
		 * t_scl_low = 2 * CCR * I2C parent clk period
		 * So, CCR = I2C parent rate / (400 kHz * 3)
		 *
		 * For example with parent rate = 6 MHz:
		 * CCR = 6000000 / (400000 * 3) = 5
		 * t_scl_high = 5 * (1 / 6000000) = 833 ns > 600 ns
		 * t_scl_low = 2 * 5 * (1 / 6000000) = 1667 ns > 1300 ns
		 * t_scl_high + t_scl_low = 2500 ns so 400 kHz is reached
		 *
		 * Function stm32f4_i2c_set_periph_clk_freq made sure that
		 * parent rate is not higher than 46 MHz . As a result val
		 * is at most 6 bits wide and so fits into the CCR bits [11:0].
		 */
		val = DIV_ROUND_UP(i2c_dev->parent_rate, 400000 * 3);

		/* Select Fast mode */
		ccr |= STM32F4_I2C_CCR_FS;
	}

	ccr |= STM32F4_I2C_CCR_CCR(val);
	writel_relaxed(ccr, i2c_dev->base + STM32F4_I2C_CCR);
}

/**
 * stm32f4_i2c_hw_config() - Prepare I2C block
 * @i2c_dev: Controller's private data
 */
static int stm32f4_i2c_hw_config(struct stm32f4_i2c_dev *i2c_dev)
{
	int ret;

	ret = stm32f4_i2c_set_periph_clk_freq(i2c_dev);
	if (ret)
		return ret;

	stm32f4_i2c_set_rise_time(i2c_dev);

	stm32f4_i2c_set_speed_mode(i2c_dev);

	/* Enable I2C */
	writel_relaxed(STM32F4_I2C_CR1_PE, i2c_dev->base + STM32F4_I2C_CR1);

	return 0;
}

static int stm32f4_i2c_wait_free_bus(struct stm32f4_i2c_dev *i2c_dev)
{
	u32 status;
	int ret;

	ret = readl_relaxed_poll_timeout(i2c_dev->base + STM32F4_I2C_SR2,
					 status,
					 !(status & STM32F4_I2C_SR2_BUSY),
					 10, 1000);
	if (ret) {
		dev_dbg(i2c_dev->dev, "bus not free\n");
		ret = -EBUSY;
	}

	return ret;
}

/**
 * stm32f4_i2c_write_ byte() - Write a byte in the data register
 * @i2c_dev: Controller's private data
 * @byte: Data to write in the register
 */
static void stm32f4_i2c_write_byte(struct stm32f4_i2c_dev *i2c_dev, u8 byte)
{
	writel_relaxed(byte, i2c_dev->base + STM32F4_I2C_DR);
}

/**
 * stm32f4_i2c_write_msg() - Fill the data register in write mode
 * @i2c_dev: Controller's private data
 *
 * This function fills the data register with I2C transfer buffer
 */
static void stm32f4_i2c_write_msg(struct stm32f4_i2c_dev *i2c_dev)
{
	struct stm32f4_i2c_msg *msg = &i2c_dev->msg;

	stm32f4_i2c_write_byte(i2c_dev, *msg->buf++);
	msg->count--;
}

static void stm32f4_i2c_read_msg(struct stm32f4_i2c_dev *i2c_dev)
{
	struct stm32f4_i2c_msg *msg = &i2c_dev->msg;
	u32 rbuf;

	rbuf = readl_relaxed(i2c_dev->base + STM32F4_I2C_DR);
	*msg->buf++ = rbuf;
	msg->count--;
}

static void stm32f4_i2c_terminate_xfer(struct stm32f4_i2c_dev *i2c_dev)
{
	struct stm32f4_i2c_msg *msg = &i2c_dev->msg;
	void __iomem *reg;

	stm32f4_i2c_disable_irq(i2c_dev);

	reg = i2c_dev->base + STM32F4_I2C_CR1;
	if (msg->stop)
		stm32f4_i2c_set_bits(reg, STM32F4_I2C_CR1_STOP);
	else
		stm32f4_i2c_set_bits(reg, STM32F4_I2C_CR1_START);

	complete(&i2c_dev->complete);
}

/**
 * stm32f4_i2c_handle_write() - Handle FIFO empty interrupt in case of write
 * @i2c_dev: Controller's private data
 */
static void stm32f4_i2c_handle_write(struct stm32f4_i2c_dev *i2c_dev)
{
	struct stm32f4_i2c_msg *msg = &i2c_dev->msg;
	void __iomem *reg = i2c_dev->base + STM32F4_I2C_CR2;

	if (msg->count) {
		stm32f4_i2c_write_msg(i2c_dev);
		if (!msg->count) {
			/*
			 * Disable buffer interrupts for RX not empty and TX
			 * empty events
			 */
			stm32f4_i2c_clr_bits(reg, STM32F4_I2C_CR2_ITBUFEN);
		}
	} else {
		stm32f4_i2c_terminate_xfer(i2c_dev);
	}
}

/**
 * stm32f4_i2c_handle_read() - Handle FIFO empty interrupt in case of read
 * @i2c_dev: Controller's private data
 *
 * This function is called when a new data is received in data register
 */
static void stm32f4_i2c_handle_read(struct stm32f4_i2c_dev *i2c_dev)
{
	struct stm32f4_i2c_msg *msg = &i2c_dev->msg;
	void __iomem *reg = i2c_dev->base + STM32F4_I2C_CR2;

	switch (msg->count) {
	case 1:
		stm32f4_i2c_disable_irq(i2c_dev);
		stm32f4_i2c_read_msg(i2c_dev);
		complete(&i2c_dev->complete);
		break;
	/*
	 * For 2-byte reception, 3-byte reception and for Data N-2, N-1 and N
	 * for N-byte reception with N > 3, we do not have to read the data
	 * register when RX not empty event occurs as we have to wait for byte
	 * transferred finished event before reading data.
	 * So, here we just disable buffer interrupt in order to avoid another
	 * system preemption due to RX not empty event.
	 */
	case 2:
	case 3:
		stm32f4_i2c_clr_bits(reg, STM32F4_I2C_CR2_ITBUFEN);
		break;
	/*
	 * For N byte reception with N > 3 we directly read data register
	 * until N-2 data.
	 */
	default:
		stm32f4_i2c_read_msg(i2c_dev);
	}
}

/**
 * stm32f4_i2c_handle_rx_done() - Handle byte transfer finished interrupt
 * in case of read
 * @i2c_dev: Controller's private data
 *
 * This function is called when a new data is received in the shift register
 * but data register has not been read yet.
 */
static void stm32f4_i2c_handle_rx_done(struct stm32f4_i2c_dev *i2c_dev)
{
	struct stm32f4_i2c_msg *msg = &i2c_dev->msg;
	void __iomem *reg;
	u32 mask;
	int i;

	switch (msg->count) {
	case 2:
		/*
		 * In order to correctly send the Stop or Repeated Start
		 * condition on the I2C bus, the STOP/START bit has to be set
		 * before reading the last two bytes (data N-1 and N).
		 * After that, we could read the last two bytes, disable
		 * remaining interrupts and notify the end of xfer to the
		 * client
		 */
		reg = i2c_dev->base + STM32F4_I2C_CR1;
		if (msg->stop)
			stm32f4_i2c_set_bits(reg, STM32F4_I2C_CR1_STOP);
		else
			stm32f4_i2c_set_bits(reg, STM32F4_I2C_CR1_START);

		for (i = 2; i > 0; i--)
			stm32f4_i2c_read_msg(i2c_dev);

		reg = i2c_dev->base + STM32F4_I2C_CR2;
		mask = STM32F4_I2C_CR2_ITEVTEN | STM32F4_I2C_CR2_ITERREN;
		stm32f4_i2c_clr_bits(reg, mask);

		complete(&i2c_dev->complete);
		break;
	case 3:
		/*
		 * In order to correctly generate the NACK pulse after the last
		 * received data byte, we have to enable NACK before reading N-2
		 * data
		 */
		reg = i2c_dev->base + STM32F4_I2C_CR1;
		stm32f4_i2c_clr_bits(reg, STM32F4_I2C_CR1_ACK);
		stm32f4_i2c_read_msg(i2c_dev);
		break;
	default:
		stm32f4_i2c_read_msg(i2c_dev);
	}
}

/**
 * stm32f4_i2c_handle_rx_addr() - Handle address matched interrupt in case of
 * master receiver
 * @i2c_dev: Controller's private data
 */
static void stm32f4_i2c_handle_rx_addr(struct stm32f4_i2c_dev *i2c_dev)
{
	struct stm32f4_i2c_msg *msg = &i2c_dev->msg;
	u32 cr1;

	switch (msg->count) {
	case 0:
		stm32f4_i2c_terminate_xfer(i2c_dev);

		/* Clear ADDR flag */
		readl_relaxed(i2c_dev->base + STM32F4_I2C_SR2);
		break;
	case 1:
		/*
		 * Single byte reception:
		 * Enable NACK and reset POS (Acknowledge position).
		 * Then, clear ADDR flag and set STOP or RepSTART.
		 * In that way, the NACK and STOP or RepStart pulses will be
		 * sent as soon as the byte will be received in shift register
		 */
		cr1 = readl_relaxed(i2c_dev->base + STM32F4_I2C_CR1);
		cr1 &= ~(STM32F4_I2C_CR1_ACK | STM32F4_I2C_CR1_POS);
		writel_relaxed(cr1, i2c_dev->base + STM32F4_I2C_CR1);

		readl_relaxed(i2c_dev->base + STM32F4_I2C_SR2);

		if (msg->stop)
			cr1 |= STM32F4_I2C_CR1_STOP;
		else
			cr1 |= STM32F4_I2C_CR1_START;
		writel_relaxed(cr1, i2c_dev->base + STM32F4_I2C_CR1);
		break;
	case 2:
		/*
		 * 2-byte reception:
		 * Enable NACK, set POS (NACK position) and clear ADDR flag.
		 * In that way, NACK will be sent for the next byte which will
		 * be received in the shift register instead of the current
		 * one.
		 */
		cr1 = readl_relaxed(i2c_dev->base + STM32F4_I2C_CR1);
		cr1 &= ~STM32F4_I2C_CR1_ACK;
		cr1 |= STM32F4_I2C_CR1_POS;
		writel_relaxed(cr1, i2c_dev->base + STM32F4_I2C_CR1);

		readl_relaxed(i2c_dev->base + STM32F4_I2C_SR2);
		break;

	default:
		/*
		 * N-byte reception:
		 * Enable ACK, reset POS (ACK postion) and clear ADDR flag.
		 * In that way, ACK will be sent as soon as the current byte
		 * will be received in the shift register
		 */
		cr1 = readl_relaxed(i2c_dev->base + STM32F4_I2C_CR1);
		cr1 |= STM32F4_I2C_CR1_ACK;
		cr1 &= ~STM32F4_I2C_CR1_POS;
		writel_relaxed(cr1, i2c_dev->base + STM32F4_I2C_CR1);

		readl_relaxed(i2c_dev->base + STM32F4_I2C_SR2);
		break;
	}
}

/**
 * stm32f4_i2c_isr_event() - Interrupt routine for I2C bus event
 * @irq: interrupt number
 * @data: Controller's private data
 */
static irqreturn_t stm32f4_i2c_isr_event(int irq, void *data)
{
	struct stm32f4_i2c_dev *i2c_dev = data;
	struct stm32f4_i2c_msg *msg = &i2c_dev->msg;
	u32 possible_status = STM32F4_I2C_SR1_ITEVTEN_MASK;
	u32 status, ien, event, cr2;

	cr2 = readl_relaxed(i2c_dev->base + STM32F4_I2C_CR2);
	ien = cr2 & STM32F4_I2C_CR2_IRQ_MASK;

	/* Update possible_status if buffer interrupt is enabled */
	if (ien & STM32F4_I2C_CR2_ITBUFEN)
		possible_status |= STM32F4_I2C_SR1_ITBUFEN_MASK;

	status = readl_relaxed(i2c_dev->base + STM32F4_I2C_SR1);
	event = status & possible_status;
	if (!event) {
		dev_dbg(i2c_dev->dev,
			"spurious evt irq (status=0x%08x, ien=0x%08x)\n",
			status, ien);
		return IRQ_NONE;
	}

	/* Start condition generated */
	if (event & STM32F4_I2C_SR1_SB)
		stm32f4_i2c_write_byte(i2c_dev, msg->addr);

	/* I2C Address sent */
	if (event & STM32F4_I2C_SR1_ADDR) {
		if (msg->addr & I2C_M_RD)
			stm32f4_i2c_handle_rx_addr(i2c_dev);
		else
			readl_relaxed(i2c_dev->base + STM32F4_I2C_SR2);

		/*
		 * Enable buffer interrupts for RX not empty and TX empty
		 * events
		 */
		cr2 |= STM32F4_I2C_CR2_ITBUFEN;
		writel_relaxed(cr2, i2c_dev->base + STM32F4_I2C_CR2);
	}

	/* TX empty */
	if ((event & STM32F4_I2C_SR1_TXE) && !(msg->addr & I2C_M_RD))
		stm32f4_i2c_handle_write(i2c_dev);

	/* RX not empty */
	if ((event & STM32F4_I2C_SR1_RXNE) && (msg->addr & I2C_M_RD))
		stm32f4_i2c_handle_read(i2c_dev);

	/*
	 * The BTF (Byte Transfer finished) event occurs when:
	 * - in reception : a new byte is received in the shift register
	 * but the previous byte has not been read yet from data register
	 * - in transmission: a new byte should be sent but the data register
	 * has not been written yet
	 */
	if (event & STM32F4_I2C_SR1_BTF) {
		if (msg->addr & I2C_M_RD)
			stm32f4_i2c_handle_rx_done(i2c_dev);
		else
			stm32f4_i2c_handle_write(i2c_dev);
	}

	return IRQ_HANDLED;
}

/**
 * stm32f4_i2c_isr_error() - Interrupt routine for I2C bus error
 * @irq: interrupt number
 * @data: Controller's private data
 */
static irqreturn_t stm32f4_i2c_isr_error(int irq, void *data)
{
	struct stm32f4_i2c_dev *i2c_dev = data;
	struct stm32f4_i2c_msg *msg = &i2c_dev->msg;
	void __iomem *reg;
	u32 status;

	status = readl_relaxed(i2c_dev->base + STM32F4_I2C_SR1);

	/* Arbitration lost */
	if (status & STM32F4_I2C_SR1_ARLO) {
		status &= ~STM32F4_I2C_SR1_ARLO;
		writel_relaxed(status, i2c_dev->base + STM32F4_I2C_SR1);
		msg->result = -EAGAIN;
	}

	/*
	 * Acknowledge failure:
	 * In master transmitter mode a Stop must be generated by software
	 */
	if (status & STM32F4_I2C_SR1_AF) {
		if (!(msg->addr & I2C_M_RD)) {
			reg = i2c_dev->base + STM32F4_I2C_CR1;
			stm32f4_i2c_set_bits(reg, STM32F4_I2C_CR1_STOP);
		}
		status &= ~STM32F4_I2C_SR1_AF;
		writel_relaxed(status, i2c_dev->base + STM32F4_I2C_SR1);
		msg->result = -EIO;
	}

	/* Bus error */
	if (status & STM32F4_I2C_SR1_BERR) {
		status &= ~STM32F4_I2C_SR1_BERR;
		writel_relaxed(status, i2c_dev->base + STM32F4_I2C_SR1);
		msg->result = -EIO;
	}

	stm32f4_i2c_disable_irq(i2c_dev);
	complete(&i2c_dev->complete);

	return IRQ_HANDLED;
}

/**
 * stm32f4_i2c_xfer_msg() - Transfer a single I2C message
 * @i2c_dev: Controller's private data
 * @msg: I2C message to transfer
 * @is_first: first message of the sequence
 * @is_last: last message of the sequence
 */
static int stm32f4_i2c_xfer_msg(struct stm32f4_i2c_dev *i2c_dev,
				struct i2c_msg *msg, bool is_first,
				bool is_last)
{
	struct stm32f4_i2c_msg *f4_msg = &i2c_dev->msg;
	void __iomem *reg = i2c_dev->base + STM32F4_I2C_CR1;
	unsigned long timeout;
	u32 mask;
	int ret;

	f4_msg->addr = i2c_8bit_addr_from_msg(msg);
	f4_msg->buf = msg->buf;
	f4_msg->count = msg->len;
	f4_msg->result = 0;
	f4_msg->stop = is_last;

	reinit_completion(&i2c_dev->complete);

	/* Enable events and errors interrupts */
	mask = STM32F4_I2C_CR2_ITEVTEN | STM32F4_I2C_CR2_ITERREN;
	stm32f4_i2c_set_bits(i2c_dev->base + STM32F4_I2C_CR2, mask);

	if (is_first) {
		ret = stm32f4_i2c_wait_free_bus(i2c_dev);
		if (ret)
			return ret;

		/* START generation */
		stm32f4_i2c_set_bits(reg, STM32F4_I2C_CR1_START);
	}

	timeout = wait_for_completion_timeout(&i2c_dev->complete,
					      i2c_dev->adap.timeout);
	ret = f4_msg->result;

	if (!timeout)
		ret = -ETIMEDOUT;

	return ret;
}

/**
 * stm32f4_i2c_xfer() - Transfer combined I2C message
 * @i2c_adap: Adapter pointer to the controller
 * @msgs: Pointer to data to be written.
 * @num: Number of messages to be executed
 */
static int stm32f4_i2c_xfer(struct i2c_adapter *i2c_adap, struct i2c_msg msgs[],
			    int num)
{
	struct stm32f4_i2c_dev *i2c_dev = i2c_get_adapdata(i2c_adap);
	int ret, i;

	ret = clk_enable(i2c_dev->clk);
	if (ret) {
		dev_err(i2c_dev->dev, "Failed to enable clock\n");
		return ret;
	}

	for (i = 0; i < num && !ret; i++)
		ret = stm32f4_i2c_xfer_msg(i2c_dev, &msgs[i], i == 0,
					   i == num - 1);

	clk_disable(i2c_dev->clk);

	return (ret < 0) ? ret : num;
}

static u32 stm32f4_i2c_func(struct i2c_adapter *adap)
{
	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
}

static const struct i2c_algorithm stm32f4_i2c_algo = {
	.master_xfer = stm32f4_i2c_xfer,
	.functionality = stm32f4_i2c_func,
};

static int stm32f4_i2c_probe(struct platform_device *pdev)
{
	struct device_node *np = pdev->dev.of_node;
	struct stm32f4_i2c_dev *i2c_dev;
	struct resource *res;
	u32 irq_event, irq_error, clk_rate;
	struct i2c_adapter *adap;
	struct reset_control *rst;
	int ret;

	i2c_dev = devm_kzalloc(&pdev->dev, sizeof(*i2c_dev), GFP_KERNEL);
	if (!i2c_dev)
		return -ENOMEM;

	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
	i2c_dev->base = devm_ioremap_resource(&pdev->dev, res);
	if (IS_ERR(i2c_dev->base))
		return PTR_ERR(i2c_dev->base);

	irq_event = irq_of_parse_and_map(np, 0);
	if (!irq_event) {
		dev_err(&pdev->dev, "IRQ event missing or invalid\n");
		return -EINVAL;
	}

	irq_error = irq_of_parse_and_map(np, 1);
	if (!irq_error) {
		dev_err(&pdev->dev, "IRQ error missing or invalid\n");
		return -EINVAL;
	}

	i2c_dev->clk = devm_clk_get(&pdev->dev, NULL);
	if (IS_ERR(i2c_dev->clk)) {
		dev_err(&pdev->dev, "Error: Missing controller clock\n");
		return PTR_ERR(i2c_dev->clk);
	}
	ret = clk_prepare_enable(i2c_dev->clk);
	if (ret) {
		dev_err(i2c_dev->dev, "Failed to prepare_enable clock\n");
		return ret;
	}

	rst = devm_reset_control_get_exclusive(&pdev->dev, NULL);
	if (IS_ERR(rst)) {
		dev_err(&pdev->dev, "Error: Missing controller reset\n");
		ret = PTR_ERR(rst);
		goto clk_free;
	}
	reset_control_assert(rst);
	udelay(2);
	reset_control_deassert(rst);

	i2c_dev->speed = STM32_I2C_SPEED_STANDARD;
	ret = of_property_read_u32(np, "clock-frequency", &clk_rate);
	if (!ret && clk_rate >= 400000)
		i2c_dev->speed = STM32_I2C_SPEED_FAST;

	i2c_dev->dev = &pdev->dev;

	ret = devm_request_irq(&pdev->dev, irq_event, stm32f4_i2c_isr_event, 0,
			       pdev->name, i2c_dev);
	if (ret) {
		dev_err(&pdev->dev, "Failed to request irq event %i\n",
			irq_event);
		goto clk_free;
	}

	ret = devm_request_irq(&pdev->dev, irq_error, stm32f4_i2c_isr_error, 0,
			       pdev->name, i2c_dev);
	if (ret) {
		dev_err(&pdev->dev, "Failed to request irq error %i\n",
			irq_error);
		goto clk_free;
	}

	ret = stm32f4_i2c_hw_config(i2c_dev);
	if (ret)
		goto clk_free;

	adap = &i2c_dev->adap;
	i2c_set_adapdata(adap, i2c_dev);
	snprintf(adap->name, sizeof(adap->name), "STM32 I2C(%pa)", &res->start);
	adap->owner = THIS_MODULE;
	adap->timeout = 2 * HZ;
	adap->retries = 0;
	adap->algo = &stm32f4_i2c_algo;
	adap->dev.parent = &pdev->dev;
	adap->dev.of_node = pdev->dev.of_node;

	init_completion(&i2c_dev->complete);

	ret = i2c_add_adapter(adap);
	if (ret)
		goto clk_free;

	platform_set_drvdata(pdev, i2c_dev);

	clk_disable(i2c_dev->clk);

	dev_info(i2c_dev->dev, "STM32F4 I2C driver registered\n");

	return 0;

clk_free:
	clk_disable_unprepare(i2c_dev->clk);
	return ret;
}

static int stm32f4_i2c_remove(struct platform_device *pdev)
{
	struct stm32f4_i2c_dev *i2c_dev = platform_get_drvdata(pdev);

	i2c_del_adapter(&i2c_dev->adap);

	clk_unprepare(i2c_dev->clk);

	return 0;
}

static const struct of_device_id stm32f4_i2c_match[] = {
	{ .compatible = "st,stm32f4-i2c", },
	{},
};
MODULE_DEVICE_TABLE(of, stm32f4_i2c_match);

static struct platform_driver stm32f4_i2c_driver = {
	.driver = {
		.name = "stm32f4-i2c",
		.of_match_table = stm32f4_i2c_match,
	},
	.probe = stm32f4_i2c_probe,
	.remove = stm32f4_i2c_remove,
};

module_platform_driver(stm32f4_i2c_driver);

MODULE_AUTHOR("M'boumba Cedric Madianga <cedric.madianga@gmail.com>");
MODULE_DESCRIPTION("STMicroelectronics STM32F4 I2C driver");
MODULE_LICENSE("GPL v2");