Contributors: 7
Author Tokens Token Proportion Commits Commit Proportion
Michael Hennerich 142 62.56% 2 13.33%
Lars-Peter Clausen 62 27.31% 7 46.67%
Alexandru Ardelean 8 3.52% 2 13.33%
Arushi Singhal 5 2.20% 1 6.67%
Alison Schofield 4 1.76% 1 6.67%
Giulio Benetti 3 1.32% 1 6.67%
Jonathan Cameron 3 1.32% 1 6.67%
Total 227 15 


/*
 * AD7606 ADC driver
 *
 * Copyright 2011 Analog Devices Inc.
 *
 * Licensed under the GPL-2.
 */

#ifndef IIO_ADC_AD7606_H_
#define IIO_ADC_AD7606_H_

/**
 * struct ad7606_chip_info - chip specific information
 * @channels:		channel specification
 * @num_channels:	number of channels
 * @has_oversampling:   whether the device has oversampling support
 */

struct ad7606_chip_info {
	const struct iio_chan_spec	*channels;
	unsigned int			num_channels;
	bool				has_oversampling;
};

/**
 * struct ad7606_state - driver instance specific data
 * @dev		pointer to kernel device
 * @chip_info		entry in the table of chips that describes this device
 * @reg		regulator info for the the power supply of the device
 * @poll_work		work struct for continuously reading data from the device
 *			into an IIO triggered buffer
 * @wq_data_avail	wait queue struct for buffer mode
 * @bops		bus operations (SPI or parallel)
 * @range		voltage range selection, selects which scale to apply
 * @oversampling	oversampling selection
 * @done		marks whether reading data is done
 * @base_address	address from where to read data in parallel operation
 * @lock		protect sensor state from concurrent accesses to GPIOs
 * @gpio_convst	GPIO descriptor for conversion start signal (CONVST)
 * @gpio_reset		GPIO descriptor for device hard-reset
 * @gpio_range		GPIO descriptor for range selection
 * @gpio_standby	GPIO descriptor for stand-by signal (STBY),
 *			controls power-down mode of device
 * @gpio_frstdata	GPIO descriptor for reading from device when data
 *			is being read on the first channel
 * @gpio_os		GPIO descriptors to control oversampling on the device
 * @data		buffer for reading data from the device
 */

struct ad7606_state {
	struct device			*dev;
	const struct ad7606_chip_info	*chip_info;
	struct regulator		*reg;
	struct work_struct		poll_work;
	wait_queue_head_t		wq_data_avail;
	const struct ad7606_bus_ops	*bops;
	unsigned int			range;
	unsigned int			oversampling;
	bool				done;
	void __iomem			*base_address;

	struct mutex			lock; /* protect sensor state */
	struct gpio_desc		*gpio_convst;
	struct gpio_desc		*gpio_reset;
	struct gpio_desc		*gpio_range;
	struct gpio_desc		*gpio_standby;
	struct gpio_desc		*gpio_frstdata;
	struct gpio_descs		*gpio_os;

	/*
	 * DMA (thus cache coherency maintenance) requires the
	 * transfer buffers to live in their own cache lines.
	 * 8 * 16-bit samples + 64-bit timestamp
	 */
	unsigned short			data[12] ____cacheline_aligned;
};

/**
 * struct ad7606_bus_ops - driver bus operations
 * @read_block		function pointer for reading blocks of data
 */
struct ad7606_bus_ops {
	/* more methods added in future? */
	int (*read_block)(struct device *dev, int num, void *data);
};

int ad7606_probe(struct device *dev, int irq, void __iomem *base_address,
		 const char *name, unsigned int id,
		 const struct ad7606_bus_ops *bops);
int ad7606_remove(struct device *dev, int irq);

enum ad7606_supported_device_ids {
	ID_AD7605_4,
	ID_AD7606_8,
	ID_AD7606_6,
	ID_AD7606_4
};

#ifdef CONFIG_PM_SLEEP
extern const struct dev_pm_ops ad7606_pm_ops;
#define AD7606_PM_OPS (&ad7606_pm_ops)
#else
#define AD7606_PM_OPS NULL
#endif

#endif /* IIO_ADC_AD7606_H_ */