Contributors: 16
Author Tokens Token Proportion Commits Commit Proportion
Giuseppe Cavallaro 225 40.32% 13 30.23%
Joao Pinto 139 24.91% 6 13.95%
Deepak Sikri 89 15.95% 3 6.98%
Srinivas Kandagatla 22 3.94% 3 6.98%
Corentin Labbe 16 2.87% 2 4.65%
Vince Bridgers 15 2.69% 3 6.98%
Jose Abreu 11 1.97% 3 6.98%
Niklas Cassel 9 1.61% 2 4.65%
Chen-Yu Tsai 8 1.43% 1 2.33%
Alexandre Torgue 6 1.08% 1 2.33%
Mathieu Olivari 5 0.90% 1 2.33%
Bhadram Varka 4 0.72% 1 2.33%
Sonic Zhang 3 0.54% 1 2.33%
Viresh Kumar 3 0.54% 1 2.33%
Thierry Reding 2 0.36% 1 2.33%
Masanari Iida 1 0.18% 1 2.33%
Total 558 43 


/*******************************************************************************

  Header file for stmmac platform data

  Copyright (C) 2009  STMicroelectronics Ltd

  This program is free software; you can redistribute it and/or modify it
  under the terms and conditions of the GNU General Public License,
  version 2, as published by the Free Software Foundation.

  This program is distributed in the hope it will be useful, but WITHOUT
  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
  more details.

  You should have received a copy of the GNU General Public License along with
  this program; if not, write to the Free Software Foundation, Inc.,
  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.

  The full GNU General Public License is included in this distribution in
  the file called "COPYING".

  Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
*******************************************************************************/

#ifndef __STMMAC_PLATFORM_DATA
#define __STMMAC_PLATFORM_DATA

#include <linux/platform_device.h>

#define MTL_MAX_RX_QUEUES	8
#define MTL_MAX_TX_QUEUES	8
#define STMMAC_CH_MAX		8

#define STMMAC_RX_COE_NONE	0
#define STMMAC_RX_COE_TYPE1	1
#define STMMAC_RX_COE_TYPE2	2

/* Define the macros for CSR clock range parameters to be passed by
 * platform code.
 * This could also be configured at run time using CPU freq framework. */

/* MDC Clock Selection define*/
#define	STMMAC_CSR_60_100M	0x0	/* MDC = clk_scr_i/42 */
#define	STMMAC_CSR_100_150M	0x1	/* MDC = clk_scr_i/62 */
#define	STMMAC_CSR_20_35M	0x2	/* MDC = clk_scr_i/16 */
#define	STMMAC_CSR_35_60M	0x3	/* MDC = clk_scr_i/26 */
#define	STMMAC_CSR_150_250M	0x4	/* MDC = clk_scr_i/102 */
#define	STMMAC_CSR_250_300M	0x5	/* MDC = clk_scr_i/122 */

/* MTL algorithms identifiers */
#define MTL_TX_ALGORITHM_WRR	0x0
#define MTL_TX_ALGORITHM_WFQ	0x1
#define MTL_TX_ALGORITHM_DWRR	0x2
#define MTL_TX_ALGORITHM_SP	0x3
#define MTL_RX_ALGORITHM_SP	0x4
#define MTL_RX_ALGORITHM_WSP	0x5

/* RX/TX Queue Mode */
#define MTL_QUEUE_AVB		0x0
#define MTL_QUEUE_DCB		0x1

/* The MDC clock could be set higher than the IEEE 802.3
 * specified frequency limit 0f 2.5 MHz, by programming a clock divider
 * of value different than the above defined values. The resultant MDIO
 * clock frequency of 12.5 MHz is applicable for the interfacing chips
 * supporting higher MDC clocks.
 * The MDC clock selection macros need to be defined for MDC clock rate
 * of 12.5 MHz, corresponding to the following selection.
 */
#define STMMAC_CSR_I_4		0x8	/* clk_csr_i/4 */
#define STMMAC_CSR_I_6		0x9	/* clk_csr_i/6 */
#define STMMAC_CSR_I_8		0xA	/* clk_csr_i/8 */
#define STMMAC_CSR_I_10		0xB	/* clk_csr_i/10 */
#define STMMAC_CSR_I_12		0xC	/* clk_csr_i/12 */
#define STMMAC_CSR_I_14		0xD	/* clk_csr_i/14 */
#define STMMAC_CSR_I_16		0xE	/* clk_csr_i/16 */
#define STMMAC_CSR_I_18		0xF	/* clk_csr_i/18 */

/* AXI DMA Burst length supported */
#define DMA_AXI_BLEN_4		(1 << 1)
#define DMA_AXI_BLEN_8		(1 << 2)
#define DMA_AXI_BLEN_16		(1 << 3)
#define DMA_AXI_BLEN_32		(1 << 4)
#define DMA_AXI_BLEN_64		(1 << 5)
#define DMA_AXI_BLEN_128	(1 << 6)
#define DMA_AXI_BLEN_256	(1 << 7)
#define DMA_AXI_BLEN_ALL (DMA_AXI_BLEN_4 | DMA_AXI_BLEN_8 | DMA_AXI_BLEN_16 \
			| DMA_AXI_BLEN_32 | DMA_AXI_BLEN_64 \
			| DMA_AXI_BLEN_128 | DMA_AXI_BLEN_256)

/* Platfrom data for platform device structure's platform_data field */

struct stmmac_mdio_bus_data {
	int (*phy_reset)(void *priv);
	unsigned int phy_mask;
	int *irqs;
	int probed_phy_irq;
#ifdef CONFIG_OF
	int reset_gpio, active_low;
	u32 delays[3];
#endif
};

struct stmmac_dma_cfg {
	int pbl;
	int txpbl;
	int rxpbl;
	bool pblx8;
	int fixed_burst;
	int mixed_burst;
	bool aal;
};

#define AXI_BLEN	7
struct stmmac_axi {
	bool axi_lpi_en;
	bool axi_xit_frm;
	u32 axi_wr_osr_lmt;
	u32 axi_rd_osr_lmt;
	bool axi_kbbe;
	u32 axi_blen[AXI_BLEN];
	bool axi_fb;
	bool axi_mb;
	bool axi_rb;
};

struct stmmac_rxq_cfg {
	u8 mode_to_use;
	u32 chan;
	u8 pkt_route;
	bool use_prio;
	u32 prio;
};

struct stmmac_txq_cfg {
	u32 weight;
	u8 mode_to_use;
	/* Credit Base Shaper parameters */
	u32 send_slope;
	u32 idle_slope;
	u32 high_credit;
	u32 low_credit;
	bool use_prio;
	u32 prio;
};

struct plat_stmmacenet_data {
	int bus_id;
	int phy_addr;
	int interface;
	struct stmmac_mdio_bus_data *mdio_bus_data;
	struct device_node *phy_node;
	struct device_node *mdio_node;
	struct stmmac_dma_cfg *dma_cfg;
	int clk_csr;
	int has_gmac;
	int enh_desc;
	int tx_coe;
	int rx_coe;
	int bugged_jumbo;
	int pmt;
	int force_sf_dma_mode;
	int force_thresh_dma_mode;
	int riwt_off;
	int max_speed;
	int maxmtu;
	int multicast_filter_bins;
	int unicast_filter_entries;
	int tx_fifo_size;
	int rx_fifo_size;
	u32 rx_queues_to_use;
	u32 tx_queues_to_use;
	u8 rx_sched_algorithm;
	u8 tx_sched_algorithm;
	struct stmmac_rxq_cfg rx_queues_cfg[MTL_MAX_RX_QUEUES];
	struct stmmac_txq_cfg tx_queues_cfg[MTL_MAX_TX_QUEUES];
	void (*fix_mac_speed)(void *priv, unsigned int speed);
	int (*init)(struct platform_device *pdev, void *priv);
	void (*exit)(struct platform_device *pdev, void *priv);
	struct mac_device_info *(*setup)(void *priv);
	void *bsp_priv;
	struct clk *stmmac_clk;
	struct clk *pclk;
	struct clk *clk_ptp_ref;
	unsigned int clk_ptp_rate;
	unsigned int clk_ref_rate;
	struct reset_control *stmmac_rst;
	struct stmmac_axi *axi;
	int has_gmac4;
	bool has_sun8i;
	bool tso_en;
	int mac_port_sel_speed;
	bool en_tx_lpi_clockgating;
	int has_xgmac;
};
#endif