Contributors: 7
Author Tokens Token Proportion Commits Commit Proportion
Phillip Potter 5523 94.52% 1 3.70%
Michael Straube 165 2.82% 16 59.26%
Martin Kaiser 73 1.25% 4 14.81%
Larry Finger 72 1.23% 3 11.11%
Greg Kroah-Hartman 7 0.12% 1 3.70%
Pavel Skripkin 2 0.03% 1 3.70%
Haowen Bai 1 0.02% 1 3.70%
Total 5843 27 


// SPDX-License-Identifier: GPL-2.0
/* Copyright(c) 2007 - 2011 Realtek Corporation. */

#define _HCI_HAL_INIT_C_

#include "../include/osdep_service.h"
#include "../include/drv_types.h"
#include "../include/rtw_efuse.h"
#include "../include/rtw_fw.h"
#include "../include/rtl8188e_hal.h"
#include "../include/rtw_iol.h"
#include "../include/usb_ops.h"
#include "../include/usb_osintf.h"
#include "../include/Hal8188EPwrSeq.h"

static void _ConfigNormalChipOutEP_8188E(struct adapter *adapt, u8 NumOutPipe)
{
	struct hal_data_8188e *haldata = &adapt->haldata;

	switch (NumOutPipe) {
	case	3:
		haldata->OutEpQueueSel = TX_SELE_HQ | TX_SELE_LQ | TX_SELE_NQ;
		haldata->OutEpNumber = 3;
		break;
	case	2:
		haldata->OutEpQueueSel = TX_SELE_HQ | TX_SELE_NQ;
		haldata->OutEpNumber = 2;
		break;
	case	1:
		haldata->OutEpQueueSel = TX_SELE_HQ;
		haldata->OutEpNumber = 1;
		break;
	default:
		break;
	}
}

static bool HalUsbSetQueuePipeMapping8188EUsb(struct adapter *adapt, u8 NumOutPipe)
{

	_ConfigNormalChipOutEP_8188E(adapt, NumOutPipe);
	return Hal_MappingOutPipe(adapt, NumOutPipe);
}

void rtl8188eu_interface_configure(struct adapter *adapt)
{
	struct dvobj_priv *pdvobjpriv = adapter_to_dvobj(adapt);

	HalUsbSetQueuePipeMapping8188EUsb(adapt, pdvobjpriv->RtNumOutPipes);
}

u32 rtl8188eu_InitPowerOn(struct adapter *adapt)
{
	u16 value16;
	/*  HW Power on sequence */
	struct hal_data_8188e *haldata = &adapt->haldata;
	if (haldata->bMacPwrCtrlOn)
		return _SUCCESS;

	if (!HalPwrSeqCmdParsing(adapt, Rtl8188E_NIC_PWR_ON_FLOW))
		return _FAIL;

	/*  Enable MAC DMA/WMAC/SCHEDULE/SEC block */
	/*  Set CR bit10 to enable 32k calibration. Suggested by SD1 Gimmy. Added by tynli. 2011.08.31. */
	rtw_write16(adapt, REG_CR, 0x00);  /* suggseted by zhouzhou, by page, 20111230 */

		/*  Enable MAC DMA/WMAC/SCHEDULE/SEC block */
	value16 = rtw_read16(adapt, REG_CR);
	value16 |= (HCI_TXDMA_EN | HCI_RXDMA_EN | TXDMA_EN | RXDMA_EN
				| PROTOCOL_EN | SCHEDULE_EN | ENSEC | CALTMR_EN);
	/*  for SDIO - Set CR bit10 to enable 32k calibration. Suggested by SD1 Gimmy. Added by tynli. 2011.08.31. */

	rtw_write16(adapt, REG_CR, value16);
	haldata->bMacPwrCtrlOn = true;

	return _SUCCESS;
}

/*  Shall USB interface init this? */
static void _InitInterrupt(struct adapter *Adapter)
{
	u32 imr, imr_ex;
	u8  usb_opt;

	/* HISR write one to clear */
	rtw_write32(Adapter, REG_HISR_88E, 0xFFFFFFFF);
	/*  HIMR - */
	imr = IMR_PSTIMEOUT_88E | IMR_TBDER_88E | IMR_CPWM_88E | IMR_CPWM2_88E;
	rtw_write32(Adapter, REG_HIMR_88E, imr);

	imr_ex = IMR_TXERR_88E | IMR_RXERR_88E | IMR_TXFOVW_88E | IMR_RXFOVW_88E;
	rtw_write32(Adapter, REG_HIMRE_88E, imr_ex);

	/*  REG_USB_SPECIAL_OPTION - BIT(4) */
	/*  0; Use interrupt endpoint to upload interrupt pkt */
	/*  1; Use bulk endpoint to upload interrupt pkt, */
	usb_opt = rtw_read8(Adapter, REG_USB_SPECIAL_OPTION);

	if (adapter_to_dvobj(Adapter)->pusbdev->speed == USB_SPEED_HIGH)
		usb_opt = usb_opt | (INT_BULK_SEL);
	else
		usb_opt = usb_opt & (~INT_BULK_SEL);

	rtw_write8(Adapter, REG_USB_SPECIAL_OPTION, usb_opt);
}

static void _InitQueueReservedPage(struct adapter *Adapter)
{
	struct hal_data_8188e *haldata = &Adapter->haldata;
	struct registry_priv	*pregistrypriv = &Adapter->registrypriv;
	u32 numHQ	= 0;
	u32 numLQ	= 0;
	u32 numNQ	= 0;
	u32 numPubQ;
	u32 value32;
	u8 value8;
	bool bWiFiConfig = pregistrypriv->wifi_spec;

	if (bWiFiConfig) {
		if (haldata->OutEpQueueSel & TX_SELE_HQ)
			numHQ =  0x29;

		if (haldata->OutEpQueueSel & TX_SELE_LQ)
			numLQ = 0x1C;

		/*  NOTE: This step shall be proceed before writing REG_RQPN. */
		if (haldata->OutEpQueueSel & TX_SELE_NQ)
			numNQ = 0x1C;
		value8 = (u8)_NPQ(numNQ);
		rtw_write8(Adapter, REG_RQPN_NPQ, value8);

		numPubQ = 0xA8 - numHQ - numLQ - numNQ;

		/*  TX DMA */
		value32 = _HPQ(numHQ) | _LPQ(numLQ) | _PUBQ(numPubQ) | LD_RQPN;
		rtw_write32(Adapter, REG_RQPN, value32);
	} else {
		rtw_write16(Adapter, REG_RQPN_NPQ, 0x0000);/* Just follow MP Team,??? Georgia 03/28 */
		rtw_write16(Adapter, REG_RQPN_NPQ, 0x0d);
		rtw_write32(Adapter, REG_RQPN, 0x808E000d);/* reserve 7 page for LPS */
	}
}

static void _InitTxBufferBoundary(struct adapter *Adapter, u8 txpktbuf_bndy)
{
	rtw_write8(Adapter, REG_TXPKTBUF_BCNQ_BDNY, txpktbuf_bndy);
	rtw_write8(Adapter, REG_TXPKTBUF_MGQ_BDNY, txpktbuf_bndy);
	rtw_write8(Adapter, REG_TXPKTBUF_WMAC_LBK_BF_HD, txpktbuf_bndy);
	rtw_write8(Adapter, REG_TRXFF_BNDY, txpktbuf_bndy);
	rtw_write8(Adapter, REG_TDECTRL + 1, txpktbuf_bndy);
}

static void _InitPageBoundary(struct adapter *Adapter)
{
	/*  RX Page Boundary */
	/*  */
	u16 rxff_bndy = MAX_RX_DMA_BUFFER_SIZE_88E - 1;

	rtw_write16(Adapter, (REG_TRXFF_BNDY + 2), rxff_bndy);
}

static void _InitNormalChipRegPriority(struct adapter *Adapter, u16 beQ,
				       u16 bkQ, u16 viQ, u16 voQ, u16 mgtQ,
				       u16 hiQ)
{
	u16 value16	= (rtw_read16(Adapter, REG_TRXDMA_CTRL) & 0x7);

	value16 |= _TXDMA_BEQ_MAP(beQ)	| _TXDMA_BKQ_MAP(bkQ) |
		   _TXDMA_VIQ_MAP(viQ)	| _TXDMA_VOQ_MAP(voQ) |
		   _TXDMA_MGQ_MAP(mgtQ) | _TXDMA_HIQ_MAP(hiQ);

	rtw_write16(Adapter, REG_TRXDMA_CTRL, value16);
}

static void _InitNormalChipOneOutEpPriority(struct adapter *Adapter)
{
	struct hal_data_8188e *haldata = &Adapter->haldata;

	u16 value = 0;
	switch (haldata->OutEpQueueSel) {
	case TX_SELE_HQ:
		value = QUEUE_HIGH;
		break;
	case TX_SELE_LQ:
		value = QUEUE_LOW;
		break;
	case TX_SELE_NQ:
		value = QUEUE_NORMAL;
		break;
	default:
		break;
	}
	_InitNormalChipRegPriority(Adapter, value, value, value, value,
				   value, value);
}

static void _InitNormalChipTwoOutEpPriority(struct adapter *Adapter)
{
	struct hal_data_8188e *haldata = &Adapter->haldata;
	struct registry_priv *pregistrypriv = &Adapter->registrypriv;
	u16 beQ, bkQ, viQ, voQ, mgtQ, hiQ;
	u16 valueHi = 0;
	u16 valueLow = 0;

	switch (haldata->OutEpQueueSel) {
	case (TX_SELE_HQ | TX_SELE_LQ):
		valueHi = QUEUE_HIGH;
		valueLow = QUEUE_LOW;
		break;
	case (TX_SELE_NQ | TX_SELE_LQ):
		valueHi = QUEUE_NORMAL;
		valueLow = QUEUE_LOW;
		break;
	case (TX_SELE_HQ | TX_SELE_NQ):
		valueHi = QUEUE_HIGH;
		valueLow = QUEUE_NORMAL;
		break;
	default:
		break;
	}

	if (!pregistrypriv->wifi_spec) {
		beQ	= valueLow;
		bkQ	= valueLow;
		viQ	= valueHi;
		voQ	= valueHi;
		mgtQ	= valueHi;
		hiQ	= valueHi;
	} else {/* for WMM ,CONFIG_OUT_EP_WIFI_MODE */
		beQ	= valueLow;
		bkQ	= valueHi;
		viQ	= valueHi;
		voQ	= valueLow;
		mgtQ	= valueHi;
		hiQ	= valueHi;
	}
	_InitNormalChipRegPriority(Adapter, beQ, bkQ, viQ, voQ, mgtQ, hiQ);
}

static void _InitNormalChipThreeOutEpPriority(struct adapter *Adapter)
{
	struct registry_priv *pregistrypriv = &Adapter->registrypriv;
	u16 beQ, bkQ, viQ, voQ, mgtQ, hiQ;

	if (!pregistrypriv->wifi_spec) {/*  typical setting */
		beQ	= QUEUE_LOW;
		bkQ	= QUEUE_LOW;
		viQ	= QUEUE_NORMAL;
		voQ	= QUEUE_HIGH;
		mgtQ	= QUEUE_HIGH;
		hiQ	= QUEUE_HIGH;
	} else {/*  for WMM */
		beQ	= QUEUE_LOW;
		bkQ	= QUEUE_NORMAL;
		viQ	= QUEUE_NORMAL;
		voQ	= QUEUE_HIGH;
		mgtQ	= QUEUE_HIGH;
		hiQ	= QUEUE_HIGH;
	}
	_InitNormalChipRegPriority(Adapter, beQ, bkQ, viQ, voQ, mgtQ, hiQ);
}

static void _InitQueuePriority(struct adapter *Adapter)
{
	struct hal_data_8188e *haldata = &Adapter->haldata;

	switch (haldata->OutEpNumber) {
	case 1:
		_InitNormalChipOneOutEpPriority(Adapter);
		break;
	case 2:
		_InitNormalChipTwoOutEpPriority(Adapter);
		break;
	case 3:
		_InitNormalChipThreeOutEpPriority(Adapter);
		break;
	default:
		break;
	}
}

static void _InitNetworkType(struct adapter *Adapter)
{
	u32 value32;

	value32 = rtw_read32(Adapter, REG_CR);
	/*  TODO: use the other function to set network type */
	value32 = (value32 & ~MASK_NETTYPE) | _NETTYPE(NT_LINK_AP);

	rtw_write32(Adapter, REG_CR, value32);
}

static void _InitTransferPageSize(struct adapter *Adapter)
{
	/*  Tx page size is always 128. */

	u8 value8;
	value8 = _PSRX(PBP_128) | _PSTX(PBP_128);
	rtw_write8(Adapter, REG_PBP, value8);
}

static void _InitDriverInfoSize(struct adapter *Adapter, u8 drvInfoSize)
{
	rtw_write8(Adapter, REG_RX_DRVINFO_SZ, drvInfoSize);
}

static void _InitWMACSetting(struct adapter *Adapter)
{
	u32 receive_config = RCR_AAP | RCR_APM | RCR_AM | RCR_AB |
			     RCR_CBSSID_DATA | RCR_CBSSID_BCN |
			     RCR_APP_ICV | RCR_AMF | RCR_HTC_LOC_CTRL |
			     RCR_APP_MIC | RCR_APP_PHYSTS;

	/*  some REG_RCR will be modified later by phy_ConfigMACWithHeaderFile() */
	rtw_write32(Adapter, REG_RCR, receive_config);

	/*  Accept all multicast address */
	rtw_write32(Adapter, REG_MAR, 0xFFFFFFFF);
	rtw_write32(Adapter, REG_MAR + 4, 0xFFFFFFFF);
}

static void _InitAdaptiveCtrl(struct adapter *Adapter)
{
	u16 value16;
	u32 value32;

	/*  Response Rate Set */
	value32 = rtw_read32(Adapter, REG_RRSR);
	value32 &= ~RATE_BITMAP_ALL;
	value32 |= RATE_RRSR_CCK_ONLY_1M;
	rtw_write32(Adapter, REG_RRSR, value32);

	/*  CF-END Threshold */

	/*  SIFS (used in NAV) */
	value16 = _SPEC_SIFS_CCK(0x10) | _SPEC_SIFS_OFDM(0x10);
	rtw_write16(Adapter, REG_SPEC_SIFS, value16);

	/*  Retry Limit */
	value16 = _LRL(0x30) | _SRL(0x30);
	rtw_write16(Adapter, REG_RL, value16);
}

static void _InitEDCA(struct adapter *Adapter)
{
	/*  Set Spec SIFS (used in NAV) */
	rtw_write16(Adapter, REG_SPEC_SIFS, 0x100a);
	rtw_write16(Adapter, REG_MAC_SPEC_SIFS, 0x100a);

	/*  Set SIFS for CCK */
	rtw_write16(Adapter, REG_SIFS_CTX, 0x100a);

	/*  Set SIFS for OFDM */
	rtw_write16(Adapter, REG_SIFS_TRX, 0x100a);

	/*  TXOP */
	rtw_write32(Adapter, REG_EDCA_BE_PARAM, 0x005EA42B);
	rtw_write32(Adapter, REG_EDCA_BK_PARAM, 0x0000A44F);
	rtw_write32(Adapter, REG_EDCA_VI_PARAM, 0x005EA324);
	rtw_write32(Adapter, REG_EDCA_VO_PARAM, 0x002FA226);
}

static void _InitRetryFunction(struct adapter *Adapter)
{
	u8 value8;

	value8 = rtw_read8(Adapter, REG_FWHW_TXQ_CTRL);
	value8 |= EN_AMPDU_RTY_NEW;
	rtw_write8(Adapter, REG_FWHW_TXQ_CTRL, value8);

	/*  Set ACK timeout */
	rtw_write8(Adapter, REG_ACKTO, 0x40);
}

/*-----------------------------------------------------------------------------
 * Function:	usb_AggSettingTxUpdate()
 *
 * Overview:	Separate TX/RX parameters update independent for TP detection and
 *			dynamic TX/RX aggreagtion parameters update.
 *
 * Input:			struct adapter *
 *
 * Output/Return:	NONE
 *
 * Revised History:
 *	When		Who		Remark
 *	12/10/2010	MHC		Separate to smaller function.
 *
 *---------------------------------------------------------------------------*/
static void usb_AggSettingTxUpdate(struct adapter *Adapter)
{
	u32 value32;

	if (Adapter->registrypriv.wifi_spec)
		return;

	value32 = rtw_read32(Adapter, REG_TDECTRL);
	value32 = value32 & ~(BLK_DESC_NUM_MASK << BLK_DESC_NUM_SHIFT);
	value32 |= ((USB_TXAGG_DESC_NUM & BLK_DESC_NUM_MASK) << BLK_DESC_NUM_SHIFT);

	rtw_write32(Adapter, REG_TDECTRL, value32);
}

/*-----------------------------------------------------------------------------
 * Function:	usb_AggSettingRxUpdate()
 *
 * Overview:	Separate TX/RX parameters update independent for TP detection and
 *			dynamic TX/RX aggreagtion parameters update.
 *
 * Input:			struct adapter *
 *
 * Output/Return:	NONE
 *
 * Revised History:
 *	When		Who		Remark
 *	12/10/2010	MHC		Separate to smaller function.
 *
 *---------------------------------------------------------------------------*/
static void
usb_AggSettingRxUpdate(
		struct adapter *Adapter
	)
{
	u8 valueDMA;
	u8 valueUSB;

	valueDMA = rtw_read8(Adapter, REG_TRXDMA_CTRL);
	valueUSB = rtw_read8(Adapter, REG_USB_SPECIAL_OPTION);

	valueDMA |= RXDMA_AGG_EN;
	valueUSB &= ~USB_AGG_EN;

	rtw_write8(Adapter, REG_TRXDMA_CTRL, valueDMA);
	rtw_write8(Adapter, REG_USB_SPECIAL_OPTION, valueUSB);

	rtw_write8(Adapter, REG_RXDMA_AGG_PG_TH, USB_RXAGG_PAGE_COUNT);
	rtw_write8(Adapter, REG_RXDMA_AGG_PG_TH + 1, USB_RXAGG_PAGE_TIMEOUT);
}

static void InitUsbAggregationSetting(struct adapter *Adapter)
{
	/*  Tx aggregation setting */
	usb_AggSettingTxUpdate(Adapter);

	/*  Rx aggregation setting */
	usb_AggSettingRxUpdate(Adapter);
}

static void _InitBeaconParameters(struct adapter *Adapter)
{
	struct hal_data_8188e *haldata = &Adapter->haldata;

	rtw_write16(Adapter, REG_BCN_CTRL, 0x1010);

	/*  TODO: Remove these magic number */
	rtw_write16(Adapter, REG_TBTT_PROHIBIT, 0x6404);/*  ms */
	rtw_write8(Adapter, REG_DRVERLYINT, DRIVER_EARLY_INT_TIME);/*  5ms */
	rtw_write8(Adapter, REG_BCNDMATIM, BCN_DMA_ATIME_INT_TIME); /*  2ms */

	/*  Suggested by designer timchen. Change beacon AIFS to the largest number */
	/*  beacause test chip does not contension before sending beacon. by tynli. 2009.11.03 */
	rtw_write16(Adapter, REG_BCNTCFG, 0x660F);

	haldata->RegFwHwTxQCtrl = rtw_read8(Adapter, REG_FWHW_TXQ_CTRL + 2);
	haldata->RegReg542 = rtw_read8(Adapter, REG_TBTT_PROHIBIT + 2);
	haldata->RegCR_1 = rtw_read8(Adapter, REG_CR + 1);
}

static void _BeaconFunctionEnable(struct adapter *Adapter,
				  bool Enable, bool Linked)
{
	rtw_write8(Adapter, REG_BCN_CTRL, (BIT(4) | BIT(3) | BIT(1)));

	rtw_write8(Adapter, REG_RD_CTRL + 1, 0x6F);
}

/*  Set CCK and OFDM Block "ON" */
static void _BBTurnOnBlock(struct adapter *Adapter)
{
	rtl8188e_PHY_SetBBReg(Adapter, rFPGA0_RFMOD, bCCKEn, 0x1);
	rtl8188e_PHY_SetBBReg(Adapter, rFPGA0_RFMOD, bOFDMEn, 0x1);
}

static void _InitAntenna_Selection(struct adapter *Adapter)
{
	struct hal_data_8188e *haldata = &Adapter->haldata;

	if (haldata->AntDivCfg == 0)
		return;

	rtw_write32(Adapter, REG_LEDCFG0, rtw_read32(Adapter, REG_LEDCFG0) | BIT(23));
	rtl8188e_PHY_SetBBReg(Adapter, rFPGA0_XAB_RFParameter, BIT(13), 0x01);

	if (rtl8188e_PHY_QueryBBReg(Adapter, rFPGA0_XA_RFInterfaceOE, 0x300) == Antenna_A)
		haldata->CurAntenna = Antenna_A;
	else
		haldata->CurAntenna = Antenna_B;
}

static void hw_var_set_macaddr(struct adapter *Adapter, u8 *val)
{
	u8 idx = 0;
	u32 reg_macid;

	reg_macid = REG_MACID;

	for (idx = 0; idx < 6; idx++)
		rtw_write8(Adapter, (reg_macid + idx), val[idx]);
}

u32 rtl8188eu_hal_init(struct adapter *Adapter)
{
	u8 value8 = 0;
	u16  value16;
	u8 txpktbuf_bndy;
	u32 status = _SUCCESS;
	struct hal_data_8188e *haldata = &Adapter->haldata;
	struct pwrctrl_priv		*pwrctrlpriv = &Adapter->pwrctrlpriv;
	struct registry_priv	*pregistrypriv = &Adapter->registrypriv;

	if (Adapter->pwrctrlpriv.bkeepfwalive) {
		if (haldata->odmpriv.RFCalibrateInfo.bIQKInitialized) {
			PHY_IQCalibrate_8188E(Adapter, true);
		} else {
			PHY_IQCalibrate_8188E(Adapter, false);
			haldata->odmpriv.RFCalibrateInfo.bIQKInitialized = true;
		}

		ODM_TXPowerTrackingCheck(&haldata->odmpriv);
		PHY_LCCalibrate_8188E(Adapter);

		goto exit;
	}

	status = rtl8188eu_InitPowerOn(Adapter);
	if (status == _FAIL)
		goto exit;

	/*  Save target channel */
	haldata->CurrentChannel = 6;/* default set to 6 */

	/*  2010/08/09 MH We need to check if we need to turnon or off RF after detecting */
	/*  HW GPIO pin. Before PHY_RFConfig8192C. */
	/*  2010/08/26 MH If Efuse does not support sective suspend then disable the function. */

	if (!pregistrypriv->wifi_spec) {
		txpktbuf_bndy = TX_PAGE_BOUNDARY_88E;
	} else {
		/*  for WMM */
		txpktbuf_bndy = WMM_NORMAL_TX_PAGE_BOUNDARY_88E;
	}

	_InitQueueReservedPage(Adapter);
	_InitQueuePriority(Adapter);
	_InitPageBoundary(Adapter);
	_InitTransferPageSize(Adapter);

	_InitTxBufferBoundary(Adapter, 0);

	status = rtl8188e_firmware_download(Adapter);

	if (status != _SUCCESS) {
		Adapter->bFWReady = false;
		haldata->fw_ractrl = false;
		return status;
	} else {
		Adapter->bFWReady = true;
		haldata->fw_ractrl = false;
	}
	/* Initialize firmware vars */
	Adapter->pwrctrlpriv.bFwCurrentInPSMode = false;
	haldata->LastHMEBoxNum = 0;

	status = PHY_MACConfig8188E(Adapter);
	if (status == _FAIL)
		goto exit;

	/*  */
	/* d. Initialize BB related configurations. */
	/*  */
	status = PHY_BBConfig8188E(Adapter);
	if (status == _FAIL)
		goto exit;

	status = PHY_RFConfig8188E(Adapter);
	if (status == _FAIL)
		goto exit;

	status = rtl8188e_iol_efuse_patch(Adapter);
	if (status == _FAIL)
		goto exit;

	_InitTxBufferBoundary(Adapter, txpktbuf_bndy);

	status =  InitLLTTable(Adapter, txpktbuf_bndy);
	if (status == _FAIL)
		goto exit;

	/*  Get Rx PHY status in order to report RSSI and others. */
	_InitDriverInfoSize(Adapter, DRVINFO_SZ);

	_InitInterrupt(Adapter);
	hw_var_set_macaddr(Adapter, Adapter->eeprompriv.mac_addr);
	_InitNetworkType(Adapter);/* set msr */
	_InitWMACSetting(Adapter);
	_InitAdaptiveCtrl(Adapter);
	_InitEDCA(Adapter);
	_InitRetryFunction(Adapter);
	InitUsbAggregationSetting(Adapter);
	_InitBeaconParameters(Adapter);

	/*  */
	/*  Init CR MACTXEN, MACRXEN after setting RxFF boundary REG_TRXFF_BNDY to patch */
	/*  Hw bug which Hw initials RxFF boundary size to a value which is larger than the real Rx buffer size in 88E. */
	/*  */
	/*  Enable MACTXEN/MACRXEN block */
	value16 = rtw_read16(Adapter, REG_CR);
	value16 |= (MACTXEN | MACRXEN);
	rtw_write8(Adapter, REG_CR, value16);

	/* Enable TX Report */
	/* Enable Tx Report Timer */
	value8 = rtw_read8(Adapter, REG_TX_RPT_CTRL);
	rtw_write8(Adapter,  REG_TX_RPT_CTRL, (value8 | BIT(1) | BIT(0)));
	/* Set MAX RPT MACID */
	rtw_write8(Adapter,  REG_TX_RPT_CTRL + 1, 2);/* FOR sta mode ,0: bc/mc ,1:AP */
	/* Tx RPT Timer. Unit: 32us */
	rtw_write16(Adapter, REG_TX_RPT_TIME, 0xCdf0);

	rtw_write8(Adapter, REG_EARLY_MODE_CONTROL, 0);

	rtw_write16(Adapter, REG_PKT_VO_VI_LIFE_TIME, 0x0400);	/*  unit: 256us. 256ms */
	rtw_write16(Adapter, REG_PKT_BE_BK_LIFE_TIME, 0x0400);	/*  unit: 256us. 256ms */

	/* Keep RfRegChnlVal for later use. */
	haldata->RfRegChnlVal = rtl8188e_PHY_QueryRFReg(Adapter, RF_CHNLBW, bRFRegOffsetMask);

	_BBTurnOnBlock(Adapter);

	invalidate_cam_all(Adapter);

	/*  2010/12/17 MH We need to set TX power according to EFUSE content at first. */
	PHY_SetTxPowerLevel8188E(Adapter, haldata->CurrentChannel);

/*  Move by Neo for USB SS to below setp */
/* _RfPowerSave(Adapter); */

	_InitAntenna_Selection(Adapter);

	/*  */
	/*  Disable BAR, suggested by Scott */
	/*  2010.04.09 add by hpfan */
	/*  */
	rtw_write32(Adapter, REG_BAR_MODE_CTRL, 0x0201ffff);

	/*  HW SEQ CTRL */
	/* set 0x0 to 0xFF by tynli. Default enable HW SEQ NUM. */
	rtw_write8(Adapter, REG_HWSEQ_CTRL, 0xFF);

	if (pregistrypriv->wifi_spec)
		rtw_write16(Adapter, REG_FAST_EDCA_CTRL, 0);

	/* Nav limit , suggest by scott */
	rtw_write8(Adapter, 0x652, 0x0);

	rtl8188e_InitHalDm(Adapter);

	/*  2010/08/11 MH Merge from 8192SE for Minicard init. We need to confirm current radio status */
	/*  and then decide to enable RF or not.!!!??? For Selective suspend mode. We may not */
	/*  call initstruct adapter. May cause some problem?? */
	/*  Fix the bug that Hw/Sw radio off before S3/S4, the RF off action will not be executed */
	/*  in MgntActSet_RF_State() after wake up, because the value of haldata->eRFPowerState */
	/*  is the same as eRfOff, we should change it to eRfOn after we config RF parameters. */
	/*  Added by tynli. 2010.03.30. */
	pwrctrlpriv->rf_pwrstate = rf_on;

	/*  enable Tx report. */
	rtw_write8(Adapter,  REG_FWHW_TXQ_CTRL + 1, 0x0F);

	/*  Suggested by SD1 pisa. Added by tynli. 2011.10.21. */
	rtw_write8(Adapter, REG_EARLY_MODE_CONTROL + 3, 0x01);/* Pretx_en, for WEP/TKIP SEC */

	/* tynli_test_tx_report. */
	rtw_write16(Adapter, REG_TX_RPT_TIME, 0x3DF0);

	/* enable tx DMA to drop the redundate data of packet */
	rtw_write16(Adapter, REG_TXDMA_OFFSET_CHK, (rtw_read16(Adapter, REG_TXDMA_OFFSET_CHK) | DROP_DATA_EN));

	/*  2010/08/26 MH Merge from 8192CE. */
	if (pwrctrlpriv->rf_pwrstate == rf_on) {
		if (haldata->odmpriv.RFCalibrateInfo.bIQKInitialized) {
			PHY_IQCalibrate_8188E(Adapter, true);
		} else {
			PHY_IQCalibrate_8188E(Adapter, false);
			haldata->odmpriv.RFCalibrateInfo.bIQKInitialized = true;
		}

		ODM_TXPowerTrackingCheck(&haldata->odmpriv);

		PHY_LCCalibrate_8188E(Adapter);
	}

/*	_InitPABias(Adapter); */
	rtw_write8(Adapter, REG_USB_HRPWM, 0);

	/* ack for xmit mgmt frames. */
	rtw_write32(Adapter, REG_FWHW_TXQ_CTRL, rtw_read32(Adapter, REG_FWHW_TXQ_CTRL) | BIT(12));

exit:
	return status;
}

static void CardDisableRTL8188EU(struct adapter *Adapter)
{
	u8 val8;
	struct hal_data_8188e *haldata = &Adapter->haldata;

	/* Stop Tx Report Timer. 0x4EC[Bit1]=b'0 */
	val8 = rtw_read8(Adapter, REG_TX_RPT_CTRL);
	rtw_write8(Adapter, REG_TX_RPT_CTRL, val8 & (~BIT(1)));

	/*  stop rx */
	rtw_write8(Adapter, REG_CR, 0x0);

	/*  Run LPS WL RFOFF flow */
	HalPwrSeqCmdParsing(Adapter, Rtl8188E_NIC_LPS_ENTER_FLOW);

	/*  2. 0x1F[7:0] = 0		turn off RF */

	val8 = rtw_read8(Adapter, REG_MCUFWDL);
	if ((val8 & RAM_DL_SEL) && Adapter->bFWReady) { /* 8051 RAM code */
		/*  Reset MCU 0x2[10]=0. */
		val8 = rtw_read8(Adapter, REG_SYS_FUNC_EN + 1);
		val8 &= ~BIT(2);	/*  0x2[10], FEN_CPUEN */
		rtw_write8(Adapter, REG_SYS_FUNC_EN + 1, val8);
	}

	/*  reset MCU ready status */
	rtw_write8(Adapter, REG_MCUFWDL, 0);

	/* YJ,add,111212 */
	/* Disable 32k */
	val8 = rtw_read8(Adapter, REG_32K_CTRL);
	rtw_write8(Adapter, REG_32K_CTRL, val8 & (~BIT(0)));

	/*  Card disable power action flow */
	HalPwrSeqCmdParsing(Adapter, Rtl8188E_NIC_DISABLE_FLOW);

	/*  Reset MCU IO Wrapper */
	val8 = rtw_read8(Adapter, REG_RSV_CTRL + 1);
	rtw_write8(Adapter, REG_RSV_CTRL + 1, (val8 & (~BIT(3))));
	val8 = rtw_read8(Adapter, REG_RSV_CTRL + 1);
	rtw_write8(Adapter, REG_RSV_CTRL + 1, val8 | BIT(3));

	/* YJ,test add, 111207. For Power Consumption. */
	val8 = rtw_read8(Adapter, GPIO_IN);
	rtw_write8(Adapter, GPIO_OUT, val8);
	rtw_write8(Adapter, GPIO_IO_SEL, 0xFF);/* Reg0x46 */

	val8 = rtw_read8(Adapter, REG_GPIO_IO_SEL);
	rtw_write8(Adapter, REG_GPIO_IO_SEL, (val8 << 4));
	val8 = rtw_read8(Adapter, REG_GPIO_IO_SEL + 1);
	rtw_write8(Adapter, REG_GPIO_IO_SEL + 1, val8 | 0x0F);/* Reg0x43 */
	rtw_write32(Adapter, REG_BB_PAD_CTRL, 0x00080808);/* set LNA ,TRSW,EX_PA Pin to output mode */
	haldata->bMacPwrCtrlOn = false;
	Adapter->bFWReady = false;
}

u32 rtl8188eu_hal_deinit(struct adapter *Adapter)
{
	rtw_write32(Adapter, REG_HIMR_88E, IMR_DISABLED_88E);
	rtw_write32(Adapter, REG_HIMRE_88E, IMR_DISABLED_88E);

	if (!Adapter->pwrctrlpriv.bkeepfwalive) {
		if (Adapter->hw_init_completed) {
			CardDisableRTL8188EU(Adapter);
		}
	}
	return _SUCCESS;
 }

unsigned int rtl8188eu_inirp_init(struct adapter *Adapter)
{
	u8 i;
	struct recv_buf *precvbuf;
	uint	status;
	struct recv_priv *precvpriv = &Adapter->recvpriv;

	status = _SUCCESS;

	/* issue Rx irp to receive data */
	precvbuf = (struct recv_buf *)precvpriv->precv_buf;
	for (i = 0; i < NR_RECVBUFF; i++) {
		if (!rtw_read_port(Adapter, (unsigned char *)precvbuf)) {
			status = _FAIL;
			goto exit;
		}

		precvbuf++;
		precvpriv->free_recv_buf_queue_cnt--;
	}

exit:
	return status;
}

/*  */
/*  */
/*	EEPROM/EFUSE Content Parsing */
/*  */
/*  */

static void Hal_EfuseParseMACAddr_8188EU(struct adapter *adapt, u8 *hwinfo, bool AutoLoadFail)
{
	u16 i;
	u8 sMacAddr[6] = {0x00, 0xE0, 0x4C, 0x81, 0x88, 0x02};
	struct eeprom_priv *eeprom = &adapt->eeprompriv;

	if (AutoLoadFail) {
		for (i = 0; i < 6; i++)
			eeprom->mac_addr[i] = sMacAddr[i];
	} else {
		/* Read Permanent MAC address */
		memcpy(eeprom->mac_addr, &hwinfo[EEPROM_MAC_ADDR_88EU], ETH_ALEN);
	}
}

void ReadAdapterInfo8188EU(struct adapter *Adapter)
{
	struct eeprom_priv *eeprom = &Adapter->eeprompriv;
	struct led_priv *ledpriv = &Adapter->ledpriv;
	u8 eeValue;

	/* check system boot selection */
	eeValue = rtw_read8(Adapter, REG_9346CR);
	eeprom->EepromOrEfuse		= (eeValue & BOOT_FROM_EEPROM);
	eeprom->bautoload_fail_flag	= !(eeValue & EEPROM_EN);

	if (!is_boot_from_eeprom(Adapter))
		EFUSE_ShadowMapUpdate(Adapter);

	/* parse the eeprom/efuse content */
	Hal_EfuseParseIDCode88E(Adapter, eeprom->efuse_eeprom_data);
	Hal_EfuseParseMACAddr_8188EU(Adapter, eeprom->efuse_eeprom_data, eeprom->bautoload_fail_flag);

	Hal_ReadPowerSavingMode88E(Adapter, eeprom->efuse_eeprom_data, eeprom->bautoload_fail_flag);
	Hal_ReadTxPowerInfo88E(Adapter, eeprom->efuse_eeprom_data, eeprom->bautoload_fail_flag);
	rtl8188e_EfuseParseChnlPlan(Adapter, eeprom->efuse_eeprom_data, eeprom->bautoload_fail_flag);
	Hal_EfuseParseXtal_8188E(Adapter, eeprom->efuse_eeprom_data, eeprom->bautoload_fail_flag);
	Hal_ReadAntennaDiversity88E(Adapter, eeprom->efuse_eeprom_data, eeprom->bautoload_fail_flag);
	Hal_ReadThermalMeter_88E(Adapter, eeprom->efuse_eeprom_data, eeprom->bautoload_fail_flag);

	ledpriv->bRegUseLed = true;
}

static void ResumeTxBeacon(struct adapter *adapt)
{
	struct hal_data_8188e *haldata = &adapt->haldata;

	/*  2010.03.01. Marked by tynli. No need to call workitem beacause we record the value */
	/*  which should be read from register to a global variable. */

	rtw_write8(adapt, REG_FWHW_TXQ_CTRL + 2, (haldata->RegFwHwTxQCtrl) | BIT(6));
	haldata->RegFwHwTxQCtrl |= BIT(6);
	rtw_write8(adapt, REG_TBTT_PROHIBIT + 1, 0xff);
	haldata->RegReg542 |= BIT(0);
	rtw_write8(adapt, REG_TBTT_PROHIBIT + 2, haldata->RegReg542);
}

static void StopTxBeacon(struct adapter *adapt)
{
	struct hal_data_8188e *haldata = &adapt->haldata;

	/*  2010.03.01. Marked by tynli. No need to call workitem beacause we record the value */
	/*  which should be read from register to a global variable. */

	rtw_write8(adapt, REG_FWHW_TXQ_CTRL + 2, (haldata->RegFwHwTxQCtrl) & (~BIT(6)));
	haldata->RegFwHwTxQCtrl &= (~BIT(6));
	rtw_write8(adapt, REG_TBTT_PROHIBIT + 1, 0x64);
	haldata->RegReg542 &= ~(BIT(0));
	rtw_write8(adapt, REG_TBTT_PROHIBIT + 2, haldata->RegReg542);

	 /* todo: CheckFwRsvdPageContent(Adapter);  2010.06.23. Added by tynli. */
}

static void hw_var_set_opmode(struct adapter *Adapter, u8 *val)
{
	u8 val8;
	u8 mode = *((u8 *)val);

	/*  disable Port0 TSF update */
	rtw_write8(Adapter, REG_BCN_CTRL, rtw_read8(Adapter, REG_BCN_CTRL) | BIT(4));

	/*  set net_type */
	val8 = rtw_read8(Adapter, MSR) & 0x0c;
	val8 |= mode;
	rtw_write8(Adapter, MSR, val8);

	if ((mode == _HW_STATE_STATION_) || (mode == _HW_STATE_NOLINK_)) {
		StopTxBeacon(Adapter);

		rtw_write8(Adapter, REG_BCN_CTRL, 0x19);/* disable atim wnd */
	} else if (mode == _HW_STATE_ADHOC_) {
		ResumeTxBeacon(Adapter);
		rtw_write8(Adapter, REG_BCN_CTRL, 0x1a);
	} else if (mode == _HW_STATE_AP_) {
		ResumeTxBeacon(Adapter);

		rtw_write8(Adapter, REG_BCN_CTRL, 0x12);

		/* Set RCR */
		rtw_write32(Adapter, REG_RCR, 0x7000208e);/* CBSSID_DATA must set to 0,reject ICV_ERR packet */
		/* enable to rx data frame */
		rtw_write16(Adapter, REG_RXFLTMAP2, 0xFFFF);
		/* enable to rx ps-poll */
		rtw_write16(Adapter, REG_RXFLTMAP1, 0x0400);

		/* Beacon Control related register for first time */
		rtw_write8(Adapter, REG_BCNDMATIM, 0x02); /*  2ms */

		rtw_write8(Adapter, REG_ATIMWND, 0x0a); /*  10ms */
		rtw_write16(Adapter, REG_BCNTCFG, 0x00);
		rtw_write16(Adapter, REG_TBTT_PROHIBIT, 0xff04);
		rtw_write16(Adapter, REG_TSFTR_SYN_OFFSET, 0x7fff);/*  +32767 (~32ms) */

		/* reset TSF */
		rtw_write8(Adapter, REG_DUAL_TSF_RST, BIT(0));

		/* BIT(3) - If set 0, hw will clr bcnq when tx becon ok/fail or port 0 */
		rtw_write8(Adapter, REG_MBID_NUM, rtw_read8(Adapter, REG_MBID_NUM) | BIT(3) | BIT(4));

		/* enable BCN0 Function for if1 */
		/* don't enable update TSF0 for if1 (due to TSF update when beacon/probe rsp are received) */
		rtw_write8(Adapter, REG_BCN_CTRL, (DIS_TSF_UDT0_NORMAL_CHIP | EN_BCN_FUNCTION | BIT(1)));

		/* dis BCN1 ATIM  WND if if2 is station */
		rtw_write8(Adapter, REG_BCN_CTRL_1, rtw_read8(Adapter, REG_BCN_CTRL_1) | BIT(0));
	}
}

void SetHwReg8188EU(struct adapter *Adapter, u8 variable, u8 *val)
{
	struct hal_data_8188e *haldata = &Adapter->haldata;
	struct dm_priv	*pdmpriv = &haldata->dmpriv;
	struct odm_dm_struct *podmpriv = &haldata->odmpriv;

	switch (variable) {
	case HW_VAR_SET_OPMODE:
		hw_var_set_opmode(Adapter, val);
		break;
	case HW_VAR_BASIC_RATE:
		{
			u16 BrateCfg = 0;
			u8 RateIndex = 0;

			/*  2007.01.16, by Emily */
			/*  Select RRSR (in Legacy-OFDM and CCK) */
			/*  For 8190, we select only 24M, 12M, 6M, 11M, 5.5M, 2M, and 1M from the Basic rate. */
			/*  We do not use other rates. */
			HalSetBrateCfg(Adapter, val, &BrateCfg);

			/* 2011.03.30 add by Luke Lee */
			/* CCK 2M ACK should be disabled for some BCM and Atheros AP IOT */
			/* because CCK 2M has poor TXEVM */
			/* CCK 5.5M & 11M ACK should be enabled for better performance */

			BrateCfg = (BrateCfg | 0xd) & 0x15d;

			BrateCfg |= 0x01; /*  default enable 1M ACK rate */
			/*  Set RRSR rate table. */
			rtw_write8(Adapter, REG_RRSR, BrateCfg & 0xff);
			rtw_write8(Adapter, REG_RRSR + 1, (BrateCfg >> 8) & 0xff);
			rtw_write8(Adapter, REG_RRSR + 2, rtw_read8(Adapter, REG_RRSR + 2) & 0xf0);

			/*  Set RTS initial rate */
			while (BrateCfg > 0x1) {
				BrateCfg = (BrateCfg >> 1);
				RateIndex++;
			}
			/*  Ziv - Check */
			rtw_write8(Adapter, REG_INIRTS_RATE_SEL, RateIndex);
		}
		break;
	case HW_VAR_CORRECT_TSF:
		{
			u64	tsf;
			struct mlme_ext_priv	*pmlmeext = &Adapter->mlmeextpriv;
			struct mlme_ext_info	*pmlmeinfo = &pmlmeext->mlmext_info;

			tsf = pmlmeext->TSFValue - do_div(pmlmeext->TSFValue,
							  pmlmeinfo->bcn_interval * 1024) - 1024; /* us */

			if (((pmlmeinfo->state & 0x03) == WIFI_FW_ADHOC_STATE) || ((pmlmeinfo->state & 0x03) == WIFI_FW_AP_STATE))
				StopTxBeacon(Adapter);

			/* disable related TSF function */
			rtw_write8(Adapter, REG_BCN_CTRL, rtw_read8(Adapter, REG_BCN_CTRL) & (~BIT(3)));

			rtw_write32(Adapter, REG_TSFTR, tsf);
			rtw_write32(Adapter, REG_TSFTR + 4, tsf >> 32);

			/* enable related TSF function */
			rtw_write8(Adapter, REG_BCN_CTRL, rtw_read8(Adapter, REG_BCN_CTRL) | BIT(3));

			if (((pmlmeinfo->state & 0x03) == WIFI_FW_ADHOC_STATE) || ((pmlmeinfo->state & 0x03) == WIFI_FW_AP_STATE))
				ResumeTxBeacon(Adapter);
		}
		break;
	case HW_VAR_MLME_SITESURVEY:
		if (*((u8 *)val)) { /* under sitesurvey */
			/* config RCR to receive different BSSID & not to receive data frame */
			u32 v = rtw_read32(Adapter, REG_RCR);
			v &= ~(RCR_CBSSID_BCN);
			rtw_write32(Adapter, REG_RCR, v);
			/* reject all data frame */
			rtw_write16(Adapter, REG_RXFLTMAP2, 0x00);

			/* disable update TSF */
			rtw_write8(Adapter, REG_BCN_CTRL, rtw_read8(Adapter, REG_BCN_CTRL) | BIT(4));
		} else { /* sitesurvey done */
			struct mlme_ext_priv	*pmlmeext = &Adapter->mlmeextpriv;
			struct mlme_ext_info	*pmlmeinfo = &pmlmeext->mlmext_info;

			if ((is_client_associated_to_ap(Adapter)) ||
			    ((pmlmeinfo->state & 0x03) == WIFI_FW_ADHOC_STATE)) {
				/* enable to rx data frame */
				rtw_write16(Adapter, REG_RXFLTMAP2, 0xFFFF);

				/* enable update TSF */
				rtw_write8(Adapter, REG_BCN_CTRL, rtw_read8(Adapter, REG_BCN_CTRL) & (~BIT(4)));
			} else if ((pmlmeinfo->state & 0x03) == WIFI_FW_AP_STATE) {
				rtw_write16(Adapter, REG_RXFLTMAP2, 0xFFFF);
				/* enable update TSF */
				rtw_write8(Adapter, REG_BCN_CTRL, rtw_read8(Adapter, REG_BCN_CTRL) & (~BIT(4)));
			}
			rtw_write32(Adapter, REG_RCR, rtw_read32(Adapter, REG_RCR) | RCR_CBSSID_BCN);
		}
		break;
	case HW_VAR_SLOT_TIME:
		{
			u8 u1bAIFS, aSifsTime;
			struct mlme_ext_priv	*pmlmeext = &Adapter->mlmeextpriv;
			struct mlme_ext_info	*pmlmeinfo = &pmlmeext->mlmext_info;

			rtw_write8(Adapter, REG_SLOT, val[0]);

			if (pmlmeinfo->WMM_enable == 0) {
				if (pmlmeext->cur_wireless_mode == WIRELESS_11B)
					aSifsTime = 10;
				else
					aSifsTime = 16;

				u1bAIFS = aSifsTime + (2 * pmlmeinfo->slotTime);

				/*  <Roger_EXP> Temporary removed, 2008.06.20. */
				rtw_write8(Adapter, REG_EDCA_VO_PARAM, u1bAIFS);
				rtw_write8(Adapter, REG_EDCA_VI_PARAM, u1bAIFS);
				rtw_write8(Adapter, REG_EDCA_BE_PARAM, u1bAIFS);
				rtw_write8(Adapter, REG_EDCA_BK_PARAM, u1bAIFS);
			}
		}
		break;
	case HW_VAR_DM_FLAG:
		podmpriv->SupportAbility = *((u8 *)val);
		break;
	case HW_VAR_DM_FUNC_OP:
		if (val[0])
			podmpriv->BK_SupportAbility = podmpriv->SupportAbility;
		else
			podmpriv->SupportAbility = podmpriv->BK_SupportAbility;
		break;
	case HW_VAR_DM_FUNC_RESET:
		podmpriv->SupportAbility = pdmpriv->InitODMFlag;
		break;
	case HW_VAR_DM_FUNC_CLR:
		podmpriv->SupportAbility = 0;
		break;
	case HW_VAR_AMPDU_FACTOR:
		{
			u8 RegToSet_Normal[4] = {0x41, 0xa8, 0x72, 0xb9};
			u8 FactorToSet;
			u8 *pRegToSet;
			u8 index = 0;

			pRegToSet = RegToSet_Normal; /*  0xb972a841; */
			FactorToSet = *((u8 *)val);
			if (FactorToSet <= 3) {
				FactorToSet = (1 << (FactorToSet + 2));
				if (FactorToSet > 0xf)
					FactorToSet = 0xf;

				for (index = 0; index < 4; index++) {
					if ((pRegToSet[index] & 0xf0) > (FactorToSet << 4))
						pRegToSet[index] = (pRegToSet[index] & 0x0f) | (FactorToSet << 4);

					if ((pRegToSet[index] & 0x0f) > FactorToSet)
						pRegToSet[index] = (pRegToSet[index] & 0xf0) | (FactorToSet);

					rtw_write8(Adapter, (REG_AGGLEN_LMT + index), pRegToSet[index]);
				}
			}
		}
		break;
	case HW_VAR_H2C_MEDIA_STATUS_RPT:
		rtl8188e_set_FwMediaStatus_cmd(Adapter, (*(__le16 *)val));
		break;
	default:
		break;
	}

}

void UpdateHalRAMask8188EUsb(struct adapter *adapt, u32 mac_id, u8 rssi_level)
{
	u8 init_rate = 0;
	u8 networkType, raid;
	u32 mask, rate_bitmap;
	u8 shortGIrate = false;
	int	supportRateNum = 0;
	struct sta_info	*psta;
	struct hal_data_8188e *haldata = &adapt->haldata;
	struct mlme_ext_priv	*pmlmeext = &adapt->mlmeextpriv;
	struct mlme_ext_info	*pmlmeinfo = &pmlmeext->mlmext_info;
	struct wlan_bssid_ex	*cur_network = &pmlmeinfo->network;

	if (mac_id >= NUM_STA) /* CAM_SIZE */
		return;
	psta = pmlmeinfo->FW_sta_info[mac_id].psta;
	if (!psta)
		return;
	switch (mac_id) {
	case 0:/*  for infra mode */
		supportRateNum = rtw_get_rateset_len(cur_network->SupportedRates);
		networkType = judge_network_type(adapt, cur_network->SupportedRates, supportRateNum) & 0xf;
		raid = networktype_to_raid(networkType);
		mask = update_supported_rate(cur_network->SupportedRates, supportRateNum);
		mask |= (pmlmeinfo->HT_enable) ? update_MSC_rate(&pmlmeinfo->HT_caps) : 0;
		if (support_short_GI(adapt, &pmlmeinfo->HT_caps))
			shortGIrate = true;
		break;
	case 1:/* for broadcast/multicast */
		supportRateNum = rtw_get_rateset_len(pmlmeinfo->FW_sta_info[mac_id].SupportedRates);
		if (pmlmeext->cur_wireless_mode & WIRELESS_11B)
			networkType = WIRELESS_11B;
		else
			networkType = WIRELESS_11G;
		raid = networktype_to_raid(networkType);
		mask = update_basic_rate(cur_network->SupportedRates, supportRateNum);
		break;
	default: /* for each sta in IBSS */
		supportRateNum = rtw_get_rateset_len(pmlmeinfo->FW_sta_info[mac_id].SupportedRates);
		networkType = judge_network_type(adapt, pmlmeinfo->FW_sta_info[mac_id].SupportedRates, supportRateNum) & 0xf;
		raid = networktype_to_raid(networkType);
		mask = update_supported_rate(cur_network->SupportedRates, supportRateNum);

		/* todo: support HT in IBSS */
		break;
	}

	rate_bitmap = 0x0fffffff;
	rate_bitmap = ODM_Get_Rate_Bitmap(&haldata->odmpriv, mac_id, mask, rssi_level);

	mask &= rate_bitmap;

	init_rate = get_highest_rate_idx(mask) & 0x3f;

	if (haldata->fw_ractrl) {
		mask |= ((raid << 28) & 0xf0000000);
		psta->ra_mask = mask;
		mask |= ((raid << 28) & 0xf0000000);

		/* to do ,for 8188E-SMIC */
		rtl8188e_set_raid_cmd(adapt, mask);
	} else {
		ODM_RA_UpdateRateInfo_8188E(&haldata->odmpriv,
				mac_id,
				raid,
				mask,
				shortGIrate
				);
	}
	/* set ra_id */
	psta->raid = raid;
	psta->init_rate = init_rate;
}

void SetBeaconRelatedRegisters8188EUsb(struct adapter *adapt)
{
	u32 value32;
	struct mlme_ext_priv	*pmlmeext = &adapt->mlmeextpriv;
	struct mlme_ext_info	*pmlmeinfo = &pmlmeext->mlmext_info;
	u32 bcn_ctrl_reg			= REG_BCN_CTRL;
	/* reset TSF, enable update TSF, correcting TSF On Beacon */

	/* BCN interval */
	rtw_write16(adapt, REG_BCN_INTERVAL, pmlmeinfo->bcn_interval);
	rtw_write8(adapt, REG_ATIMWND, 0x02);/*  2ms */

	_InitBeaconParameters(adapt);

	rtw_write8(adapt, REG_SLOT, 0x09);

	value32 = rtw_read32(adapt, REG_TCR);
	value32 &= ~TSFRST;
	rtw_write32(adapt,  REG_TCR, value32);

	value32 |= TSFRST;
	rtw_write32(adapt, REG_TCR, value32);

	/*  NOTE: Fix test chip's bug (about contention windows's randomness) */
	rtw_write8(adapt,  REG_RXTSF_OFFSET_CCK, 0x50);
	rtw_write8(adapt, REG_RXTSF_OFFSET_OFDM, 0x50);

	_BeaconFunctionEnable(adapt, true, true);

	ResumeTxBeacon(adapt);

	rtw_write8(adapt, bcn_ctrl_reg, rtw_read8(adapt, bcn_ctrl_reg) | BIT(1));
}

void rtl8188eu_init_default_value(struct adapter *adapt)
{
	struct hal_data_8188e *haldata = &adapt->haldata;
	struct pwrctrl_priv *pwrctrlpriv;
	u8 i;

	pwrctrlpriv = &adapt->pwrctrlpriv;

	/* init default value */
	haldata->fw_ractrl = false;
	if (!pwrctrlpriv->bkeepfwalive)
		haldata->LastHMEBoxNum = 0;

	/* init dm default value */
	haldata->odmpriv.RFCalibrateInfo.bIQKInitialized = false;
	haldata->odmpriv.RFCalibrateInfo.TM_Trigger = 0;/* for IQK */
	haldata->pwrGroupCnt = 0;
	haldata->odmpriv.RFCalibrateInfo.ThermalValue_HP_index = 0;
	for (i = 0; i < HP_THERMAL_NUM; i++)
		haldata->odmpriv.RFCalibrateInfo.ThermalValue_HP[i] = 0;
}