| Author | Tokens | Token Proportion | Commits | Commit Proportion |
|---|---|---|---|---|
| Benjamin Herrenschmidt | 831 | 85.32% | 6 | 33.33% |
| Michael Hanselmann | 112 | 11.50% | 1 | 5.56% |
| Arnd Bergmann | 17 | 1.75% | 1 | 5.56% |
| Joe Perches | 3 | 0.31% | 1 | 5.56% |
| Adrian Bunk | 2 | 0.21% | 1 | 5.56% |
| Grant C. Likely | 2 | 0.21% | 1 | 5.56% |
| Adam Buchbinder | 2 | 0.21% | 2 | 11.11% |
| Phil Carmody | 1 | 0.10% | 1 | 5.56% |
| Yannick Guerrini | 1 | 0.10% | 1 | 5.56% |
| Greg Kroah-Hartman | 1 | 0.10% | 1 | 5.56% |
| Michael Ellerman | 1 | 0.10% | 1 | 5.56% |
| Jeremy Kerr | 1 | 0.10% | 1 | 5.56% |
| Total | 974 | 18 |
/* SPDX-License-Identifier: GPL-2.0 */ #ifndef _SMU_H #define _SMU_H /* * Definitions for talking to the SMU chip in newer G5 PowerMacs */ #ifdef __KERNEL__ #include <linux/list.h> #endif #include <linux/types.h> /* * Known SMU commands * * Most of what is below comes from looking at the Open Firmware driver, * though this is still incomplete and could use better documentation here * or there... */ /* * Partition info commands * * These commands are used to retrieve the sdb-partition-XX datas from * the SMU. The length is always 2. First byte is the subcommand code * and second byte is the partition ID. * * The reply is 6 bytes: * * - 0..1 : partition address * - 2 : a byte containing the partition ID * - 3 : length (maybe other bits are rest of header ?) * * The data must then be obtained with calls to another command: * SMU_CMD_MISC_ee_GET_DATABLOCK_REC (described below). */ #define SMU_CMD_PARTITION_COMMAND 0x3e #define SMU_CMD_PARTITION_LATEST 0x01 #define SMU_CMD_PARTITION_BASE 0x02 #define SMU_CMD_PARTITION_UPDATE 0x03 /* * Fan control * * This is a "mux" for fan control commands. The command seem to * act differently based on the number of arguments. With 1 byte * of argument, this seem to be queries for fans status, setpoint, * etc..., while with 0xe arguments, we will set the fans speeds. * * Queries (1 byte arg): * --------------------- * * arg=0x01: read RPM fans status * arg=0x02: read RPM fans setpoint * arg=0x11: read PWM fans status * arg=0x12: read PWM fans setpoint * * the "status" queries return the current speed while the "setpoint" ones * return the programmed/target speed. It _seems_ that the result is a bit * mask in the first byte of active/available fans, followed by 6 words (16 * bits) containing the requested speed. * * Setpoint (14 bytes arg): * ------------------------ * * first arg byte is 0 for RPM fans and 0x10 for PWM. Second arg byte is the * mask of fans affected by the command. Followed by 6 words containing the * setpoint value for selected fans in the mask (or 0 if mask value is 0) */ #define SMU_CMD_FAN_COMMAND 0x4a /* * Battery access * * Same command number as the PMU, could it be same syntax ? */ #define SMU_CMD_BATTERY_COMMAND 0x6f #define SMU_CMD_GET_BATTERY_INFO 0x00 /* * Real time clock control * * This is a "mux", first data byte contains the "sub" command. * The "RTC" part of the SMU controls the date, time, powerup * timer, but also a PRAM * * Dates are in BCD format on 7 bytes: * [sec] [min] [hour] [weekday] [month day] [month] [year] * with month being 1 based and year minus 100 */ #define SMU_CMD_RTC_COMMAND 0x8e #define SMU_CMD_RTC_SET_PWRUP_TIMER 0x00 /* i: 7 bytes date */ #define SMU_CMD_RTC_GET_PWRUP_TIMER 0x01 /* o: 7 bytes date */ #define SMU_CMD_RTC_STOP_PWRUP_TIMER 0x02 #define SMU_CMD_RTC_SET_PRAM_BYTE_ACC 0x20 /* i: 1 byte (address?) */ #define SMU_CMD_RTC_SET_PRAM_AUTOINC 0x21 /* i: 1 byte (data?) */ #define SMU_CMD_RTC_SET_PRAM_LO_BYTES 0x22 /* i: 10 bytes */ #define SMU_CMD_RTC_SET_PRAM_HI_BYTES 0x23 /* i: 10 bytes */ #define SMU_CMD_RTC_GET_PRAM_BYTE 0x28 /* i: 1 bytes (address?) */ #define SMU_CMD_RTC_GET_PRAM_LO_BYTES 0x29 /* o: 10 bytes */ #define SMU_CMD_RTC_GET_PRAM_HI_BYTES 0x2a /* o: 10 bytes */ #define SMU_CMD_RTC_SET_DATETIME 0x80 /* i: 7 bytes date */ #define SMU_CMD_RTC_GET_DATETIME 0x81 /* o: 7 bytes date */ /* * i2c commands * * To issue an i2c command, first is to send a parameter block to the * the SMU. This is a command of type 0x9a with 9 bytes of header * eventually followed by data for a write: * * 0: bus number (from device-tree usually, SMU has lots of busses !) * 1: transfer type/format (see below) * 2: device address. For combined and combined4 type transfers, this * is the "write" version of the address (bit 0x01 cleared) * 3: subaddress length (0..3) * 4: subaddress byte 0 (or only byte for subaddress length 1) * 5: subaddress byte 1 * 6: subaddress byte 2 * 7: combined address (device address for combined mode data phase) * 8: data length * * The transfer types are the same good old Apple ones it seems, * that is: * - 0x00: Simple transfer * - 0x01: Subaddress transfer (addr write + data tx, no restart) * - 0x02: Combined transfer (addr write + restart + data tx) * * This is then followed by actual data for a write. * * At this point, the OF driver seems to have a limitation on transfer * sizes of 0xd bytes on reads and 0x5 bytes on writes. I do not know * whether this is just an OF limit due to some temporary buffer size * or if this is an SMU imposed limit. This driver has the same limitation * for now as I use a 0x10 bytes temporary buffer as well * * Once that is completed, a response is expected from the SMU. This is * obtained via a command of type 0x9a with a length of 1 byte containing * 0 as the data byte. OF also fills the rest of the data buffer with 0xff's * though I can't tell yet if this is actually necessary. Once this command * is complete, at this point, all I can tell is what OF does. OF tests * byte 0 of the reply: * - on read, 0xfe or 0xfc : bus is busy, wait (see below) or nak ? * - on read, 0x00 or 0x01 : reply is in buffer (after the byte 0) * - on write, < 0 -> failure (immediate exit) * - else, OF just exists (without error, weird) * * So on read, there is this wait-for-busy thing when getting a 0xfc or * 0xfe result. OF does a loop of up to 64 retries, waiting 20ms and * doing the above again until either the retries expire or the result * is no longer 0xfe or 0xfc * * The Darwin I2C driver is less subtle though. On any non-success status * from the response command, it waits 5ms and tries again up to 20 times, * it doesn't differentiate between fatal errors or "busy" status. * * This driver provides an asynchronous paramblock based i2c command * interface to be used either directly by low level code or by a higher * level driver interfacing to the linux i2c layer. The current * implementation of this relies on working timers & timer interrupts * though, so be careful of calling context for now. This may be "fixed" * in the future by adding a polling facility. */ #define SMU_CMD_I2C_COMMAND 0x9a /* transfer types */ #define SMU_I2C_TRANSFER_SIMPLE 0x00 #define SMU_I2C_TRANSFER_STDSUB 0x01 #define SMU_I2C_TRANSFER_COMBINED 0x02 /* * Power supply control * * The "sub" command is an ASCII string in the data, the * data length is that of the string. * * The VSLEW command can be used to get or set the voltage slewing. * - length 5 (only "VSLEW") : it returns "DONE" and 3 bytes of * reply at data offset 6, 7 and 8. * - length 8 ("VSLEWxyz") has 3 additional bytes appended, and is * used to set the voltage slewing point. The SMU replies with "DONE" * I yet have to figure out their exact meaning of those 3 bytes in * both cases. They seem to be: * x = processor mask * y = op. point index * z = processor freq. step index * I haven't yet deciphered result codes * */ #define SMU_CMD_POWER_COMMAND 0xaa #define SMU_CMD_POWER_RESTART "RESTART" #define SMU_CMD_POWER_SHUTDOWN "SHUTDOWN" #define SMU_CMD_POWER_VOLTAGE_SLEW "VSLEW" /* * Read ADC sensors * * This command takes one byte of parameter: the sensor ID (or "reg" * value in the device-tree) and returns a 16 bits value */ #define SMU_CMD_READ_ADC 0xd8 /* Misc commands * * This command seem to be a grab bag of various things * * Parameters: * 1: subcommand */ #define SMU_CMD_MISC_df_COMMAND 0xdf /* * Sets "system ready" status * * I did not yet understand how it exactly works or what it does. * * Guessing from OF code, 0x02 activates the display backlight. Apple uses/used * the same codebase for all OF versions. On PowerBooks, this command would * enable the backlight. For the G5s, it only activates the front LED. However, * don't take this for granted. * * Parameters: * 2: status [0x00, 0x01 or 0x02] */ #define SMU_CMD_MISC_df_SET_DISPLAY_LIT 0x02 /* * Sets mode of power switch. * * What this actually does is not yet known. Maybe it enables some interrupt. * * Parameters: * 2: enable power switch? [0x00 or 0x01] * 3 (optional): enable nmi? [0x00 or 0x01] * * Returns: * If parameter 2 is 0x00 and parameter 3 is not specified, returns whether * NMI is enabled. Otherwise unknown. */ #define SMU_CMD_MISC_df_NMI_OPTION 0x04 /* Sets LED dimm offset. * * The front LED dimms itself during sleep. Its brightness (or, well, the PWM * frequency) depends on current time. Therefore, the SMU needs to know the * timezone. * * Parameters: * 2-8: unknown (BCD coding) */ #define SMU_CMD_MISC_df_DIMM_OFFSET 0x99 /* * Version info commands * * Parameters: * 1 (optional): Specifies version part to retrieve * * Returns: * Version value */ #define SMU_CMD_VERSION_COMMAND 0xea #define SMU_VERSION_RUNNING 0x00 #define SMU_VERSION_BASE 0x01 #define SMU_VERSION_UPDATE 0x02 /* * Switches * * These are switches whose status seems to be known to the SMU. * * Parameters: * none * * Result: * Switch bits (ORed, see below) */ #define SMU_CMD_SWITCHES 0xdc /* Switches bits */ #define SMU_SWITCH_CASE_CLOSED 0x01 #define SMU_SWITCH_AC_POWER 0x04 #define SMU_SWITCH_POWER_SWITCH 0x08 /* * Misc commands * * This command seem to be a grab bag of various things * * SMU_CMD_MISC_ee_GET_DATABLOCK_REC is used, among others, to * transfer blocks of data from the SMU. So far, I've decrypted it's * usage to retrieve partition data. In order to do that, you have to * break your transfer in "chunks" since that command cannot transfer * more than a chunk at a time. The chunk size used by OF is 0xe bytes, * but it seems that the darwin driver will let you do 0x1e bytes if * your "PMU" version is >= 0x30. You can get the "PMU" version apparently * either in the last 16 bits of property "smu-version-pmu" or as the 16 * bytes at offset 1 of "smu-version-info" * * For each chunk, the command takes 7 bytes of arguments: * byte 0: subcommand code (0x02) * byte 1: 0x04 (always, I don't know what it means, maybe the address * space to use or some other nicety. It's hard coded in OF) * byte 2..5: SMU address of the chunk (big endian 32 bits) * byte 6: size to transfer (up to max chunk size) * * The data is returned directly */ #define SMU_CMD_MISC_ee_COMMAND 0xee #define SMU_CMD_MISC_ee_GET_DATABLOCK_REC 0x02 /* Retrieves currently used watts. * * Parameters: * 1: 0x03 (Meaning unknown) */ #define SMU_CMD_MISC_ee_GET_WATTS 0x03 #define SMU_CMD_MISC_ee_LEDS_CTRL 0x04 /* i: 00 (00,01) [00] */ #define SMU_CMD_MISC_ee_GET_DATA 0x05 /* i: 00 , o: ?? */ /* * Power related commands * * Parameters: * 1: subcommand */ #define SMU_CMD_POWER_EVENTS_COMMAND 0x8f /* SMU_POWER_EVENTS subcommands */ enum { SMU_PWR_GET_POWERUP_EVENTS = 0x00, SMU_PWR_SET_POWERUP_EVENTS = 0x01, SMU_PWR_CLR_POWERUP_EVENTS = 0x02, SMU_PWR_GET_WAKEUP_EVENTS = 0x03, SMU_PWR_SET_WAKEUP_EVENTS = 0x04, SMU_PWR_CLR_WAKEUP_EVENTS = 0x05, /* * Get last shutdown cause * * Returns: * 1 byte (signed char): Last shutdown cause. Exact meaning unknown. */ SMU_PWR_LAST_SHUTDOWN_CAUSE = 0x07, /* * Sets or gets server ID. Meaning or use is unknown. * * Parameters: * 2 (optional): Set server ID (1 byte) * * Returns: * 1 byte (server ID?) */ SMU_PWR_SERVER_ID = 0x08, }; /* Power events wakeup bits */ enum { SMU_PWR_WAKEUP_KEY = 0x01, /* Wake on key press */ SMU_PWR_WAKEUP_AC_INSERT = 0x02, /* Wake on AC adapter plug */ SMU_PWR_WAKEUP_AC_CHANGE = 0x04, SMU_PWR_WAKEUP_LID_OPEN = 0x08, SMU_PWR_WAKEUP_RING = 0x10, }; /* * - Kernel side interface - */ #ifdef __KERNEL__ /* * Asynchronous SMU commands * * Fill up this structure and submit it via smu_queue_command(), * and get notified by the optional done() callback, or because * status becomes != 1 */ struct smu_cmd; struct smu_cmd { /* public */ u8 cmd; /* command */ int data_len; /* data len */ int reply_len; /* reply len */ void *data_buf; /* data buffer */ void *reply_buf; /* reply buffer */ int status; /* command status */ void (*done)(struct smu_cmd *cmd, void *misc); void *misc; /* private */ struct list_head link; }; /* * Queues an SMU command, all fields have to be initialized */ extern int smu_queue_cmd(struct smu_cmd *cmd); /* * Simple command wrapper. This structure embeds a small buffer * to ease sending simple SMU commands from the stack */ struct smu_simple_cmd { struct smu_cmd cmd; u8 buffer[16]; }; /* * Queues a simple command. All fields will be initialized by that * function */ extern int smu_queue_simple(struct smu_simple_cmd *scmd, u8 command, unsigned int data_len, void (*done)(struct smu_cmd *cmd, void *misc), void *misc, ...); /* * Completion helper. Pass it to smu_queue_simple or as 'done' * member to smu_queue_cmd, it will call complete() on the struct * completion passed in the "misc" argument */ extern void smu_done_complete(struct smu_cmd *cmd, void *misc); /* * Synchronous helpers. Will spin-wait for completion of a command */ extern void smu_spinwait_cmd(struct smu_cmd *cmd); static inline void smu_spinwait_simple(struct smu_simple_cmd *scmd) { smu_spinwait_cmd(&scmd->cmd); } /* * Poll routine to call if blocked with irqs off */ extern void smu_poll(void); /* * Init routine, presence check.... */ extern int smu_init(void); extern int smu_present(void); struct platform_device; extern struct platform_device *smu_get_ofdev(void); /* * Common command wrappers */ extern void smu_shutdown(void); extern void smu_restart(void); struct rtc_time; extern int smu_get_rtc_time(struct rtc_time *time, int spinwait); extern int smu_set_rtc_time(struct rtc_time *time, int spinwait); /* * Kernel asynchronous i2c interface */ #define SMU_I2C_READ_MAX 0x1d #define SMU_I2C_WRITE_MAX 0x15 /* SMU i2c header, exactly matches i2c header on wire */ struct smu_i2c_param { u8 bus; /* SMU bus ID (from device tree) */ u8 type; /* i2c transfer type */ u8 devaddr; /* device address (includes direction) */ u8 sublen; /* subaddress length */ u8 subaddr[3]; /* subaddress */ u8 caddr; /* combined address, filled by SMU driver */ u8 datalen; /* length of transfer */ u8 data[SMU_I2C_READ_MAX]; /* data */ }; struct smu_i2c_cmd { /* public */ struct smu_i2c_param info; void (*done)(struct smu_i2c_cmd *cmd, void *misc); void *misc; int status; /* 1 = pending, 0 = ok, <0 = fail */ /* private */ struct smu_cmd scmd; int read; int stage; int retries; u8 pdata[32]; struct list_head link; }; /* * Call this to queue an i2c command to the SMU. You must fill info, * including info.data for a write, done and misc. * For now, no polling interface is provided so you have to use completion * callback. */ extern int smu_queue_i2c(struct smu_i2c_cmd *cmd); #endif /* __KERNEL__ */ /* * - SMU "sdb" partitions informations - */ /* * Partition header format */ struct smu_sdbp_header { __u8 id; __u8 len; __u8 version; __u8 flags; }; /* * demangle 16 and 32 bits integer in some SMU partitions * (currently, afaik, this concerns only the FVT partition * (0x12) */ #define SMU_U16_MIX(x) le16_to_cpu(x) #define SMU_U32_MIX(x) ((((x) & 0xff00ff00u) >> 8)|(((x) & 0x00ff00ffu) << 8)) /* This is the definition of the SMU sdb-partition-0x12 table (called * CPU F/V/T operating points in Darwin). The definition for all those * SMU tables should be moved to some separate file */ #define SMU_SDB_FVT_ID 0x12 struct smu_sdbp_fvt { __u32 sysclk; /* Base SysClk frequency in Hz for * this operating point. Value need to * be unmixed with SMU_U32_MIX() */ __u8 pad; __u8 maxtemp; /* Max temp. supported by this * operating point */ __u16 volts[3]; /* CPU core voltage for the 3 * PowerTune modes, a mode with * 0V = not supported. Value need * to be unmixed with SMU_U16_MIX() */ }; /* This partition contains voltage & current sensor calibration * informations */ #define SMU_SDB_CPUVCP_ID 0x21 struct smu_sdbp_cpuvcp { __u16 volt_scale; /* u4.12 fixed point */ __s16 volt_offset; /* s4.12 fixed point */ __u16 curr_scale; /* u4.12 fixed point */ __s16 curr_offset; /* s4.12 fixed point */ __s32 power_quads[3]; /* s4.28 fixed point */ }; /* This partition contains CPU thermal diode calibration */ #define SMU_SDB_CPUDIODE_ID 0x18 struct smu_sdbp_cpudiode { __u16 m_value; /* u1.15 fixed point */ __s16 b_value; /* s10.6 fixed point */ }; /* This partition contains Slots power calibration */ #define SMU_SDB_SLOTSPOW_ID 0x78 struct smu_sdbp_slotspow { __u16 pow_scale; /* u4.12 fixed point */ __s16 pow_offset; /* s4.12 fixed point */ }; /* This partition contains machine specific version information about * the sensor/control layout */ #define SMU_SDB_SENSORTREE_ID 0x25 struct smu_sdbp_sensortree { __u8 model_id; __u8 unknown[3]; }; /* This partition contains CPU thermal control PID informations. So far * only single CPU machines have been seen with an SMU, so we assume this * carries only informations for those */ #define SMU_SDB_CPUPIDDATA_ID 0x17 struct smu_sdbp_cpupiddata { __u8 unknown1; __u8 target_temp_delta; __u8 unknown2; __u8 history_len; __s16 power_adj; __u16 max_power; __s32 gp,gr,gd; }; /* Other partitions without known structures */ #define SMU_SDB_DEBUG_SWITCHES_ID 0x05 #ifdef __KERNEL__ /* * This returns the pointer to an SMU "sdb" partition data or NULL * if not found. The data format is described below */ extern const struct smu_sdbp_header *smu_get_sdb_partition(int id, unsigned int *size); /* Get "sdb" partition data from an SMU satellite */ extern struct smu_sdbp_header *smu_sat_get_sdb_partition(unsigned int sat_id, int id, unsigned int *size); #endif /* __KERNEL__ */ /* * - Userland interface - */ /* * A given instance of the device can be configured for 2 different * things at the moment: * * - sending SMU commands (default at open() time) * - receiving SMU events (not yet implemented) * * Commands are written with write() of a command block. They can be * "driver" commands (for example to switch to event reception mode) * or real SMU commands. They are made of a header followed by command * data if any. * * For SMU commands (not for driver commands), you can then read() back * a reply. The reader will be blocked or not depending on how the device * file is opened. poll() isn't implemented yet. The reply will consist * of a header as well, followed by the reply data if any. You should * always provide a buffer large enough for the maximum reply data, I * recommand one page. * * It is illegal to send SMU commands through a file descriptor configured * for events reception * */ struct smu_user_cmd_hdr { __u32 cmdtype; #define SMU_CMDTYPE_SMU 0 /* SMU command */ #define SMU_CMDTYPE_WANTS_EVENTS 1 /* switch fd to events mode */ #define SMU_CMDTYPE_GET_PARTITION 2 /* retrieve an sdb partition */ __u8 cmd; /* SMU command byte */ __u8 pad[3]; /* padding */ __u32 data_len; /* Length of data following */ }; struct smu_user_reply_hdr { __u32 status; /* Command status */ __u32 reply_len; /* Length of data follwing */ }; #endif /* _SMU_H */
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.
Created with Cregit http://github.com/cregit/cregit
Version 2.0-RC1