Contributors: 8
| Author |
Tokens |
Token Proportion |
Commits |
Commit Proportion |
| Stephen Hemminger |
879 |
94.62% |
3 |
30.00% |
| David Howells |
22 |
2.37% |
1 |
10.00% |
| Ben Hutchings |
19 |
2.05% |
1 |
10.00% |
| Divy Le Ray |
4 |
0.43% |
1 |
10.00% |
| Christophe Jaillet |
2 |
0.22% |
1 |
10.00% |
| Julia Lawall |
1 |
0.11% |
1 |
10.00% |
| Greg Kroah-Hartman |
1 |
0.11% |
1 |
10.00% |
| Tejun Heo |
1 |
0.11% |
1 |
10.00% |
| Total |
929 |
|
10 |
|
// SPDX-License-Identifier: GPL-2.0
/* $Date: 2005/11/12 02:13:49 $ $RCSfile: my3126.c,v $ $Revision: 1.15 $ */
#include "cphy.h"
#include "elmer0.h"
#include "suni1x10gexp_regs.h"
/* Port Reset */
static int my3126_reset(struct cphy *cphy, int wait)
{
/*
* This can be done through registers. It is not required since
* a full chip reset is used.
*/
return 0;
}
static int my3126_interrupt_enable(struct cphy *cphy)
{
schedule_delayed_work(&cphy->phy_update, HZ/30);
t1_tpi_read(cphy->adapter, A_ELMER0_GPO, &cphy->elmer_gpo);
return 0;
}
static int my3126_interrupt_disable(struct cphy *cphy)
{
cancel_delayed_work_sync(&cphy->phy_update);
return 0;
}
static int my3126_interrupt_clear(struct cphy *cphy)
{
return 0;
}
#define OFFSET(REG_ADDR) (REG_ADDR << 2)
static int my3126_interrupt_handler(struct cphy *cphy)
{
u32 val;
u16 val16;
u16 status;
u32 act_count;
adapter_t *adapter;
adapter = cphy->adapter;
if (cphy->count == 50) {
cphy_mdio_read(cphy, MDIO_MMD_PMAPMD, MDIO_STAT1, &val);
val16 = (u16) val;
status = cphy->bmsr ^ val16;
if (status & MDIO_STAT1_LSTATUS)
t1_link_changed(adapter, 0);
cphy->bmsr = val16;
/* We have only enabled link change interrupts so it
must be that
*/
cphy->count = 0;
}
t1_tpi_write(adapter, OFFSET(SUNI1x10GEXP_REG_MSTAT_CONTROL),
SUNI1x10GEXP_BITMSK_MSTAT_SNAP);
t1_tpi_read(adapter,
OFFSET(SUNI1x10GEXP_REG_MSTAT_COUNTER_1_LOW), &act_count);
t1_tpi_read(adapter,
OFFSET(SUNI1x10GEXP_REG_MSTAT_COUNTER_33_LOW), &val);
act_count += val;
/* Populate elmer_gpo with the register value */
t1_tpi_read(adapter, A_ELMER0_GPO, &val);
cphy->elmer_gpo = val;
if ( (val & (1 << 8)) || (val & (1 << 19)) ||
(cphy->act_count == act_count) || cphy->act_on ) {
if (is_T2(adapter))
val |= (1 << 9);
else if (t1_is_T1B(adapter))
val |= (1 << 20);
cphy->act_on = 0;
} else {
if (is_T2(adapter))
val &= ~(1 << 9);
else if (t1_is_T1B(adapter))
val &= ~(1 << 20);
cphy->act_on = 1;
}
t1_tpi_write(adapter, A_ELMER0_GPO, val);
cphy->elmer_gpo = val;
cphy->act_count = act_count;
cphy->count++;
return cphy_cause_link_change;
}
static void my3126_poll(struct work_struct *work)
{
struct cphy *cphy = container_of(work, struct cphy, phy_update.work);
my3126_interrupt_handler(cphy);
}
static int my3126_set_loopback(struct cphy *cphy, int on)
{
return 0;
}
/* To check the activity LED */
static int my3126_get_link_status(struct cphy *cphy,
int *link_ok, int *speed, int *duplex, int *fc)
{
u32 val;
u16 val16;
adapter_t *adapter;
adapter = cphy->adapter;
cphy_mdio_read(cphy, MDIO_MMD_PMAPMD, MDIO_STAT1, &val);
val16 = (u16) val;
/* Populate elmer_gpo with the register value */
t1_tpi_read(adapter, A_ELMER0_GPO, &val);
cphy->elmer_gpo = val;
*link_ok = (val16 & MDIO_STAT1_LSTATUS);
if (*link_ok) {
/* Turn on the LED. */
if (is_T2(adapter))
val &= ~(1 << 8);
else if (t1_is_T1B(adapter))
val &= ~(1 << 19);
} else {
/* Turn off the LED. */
if (is_T2(adapter))
val |= (1 << 8);
else if (t1_is_T1B(adapter))
val |= (1 << 19);
}
t1_tpi_write(adapter, A_ELMER0_GPO, val);
cphy->elmer_gpo = val;
*speed = SPEED_10000;
*duplex = DUPLEX_FULL;
/* need to add flow control */
if (fc)
*fc = PAUSE_RX | PAUSE_TX;
return 0;
}
static void my3126_destroy(struct cphy *cphy)
{
kfree(cphy);
}
static const struct cphy_ops my3126_ops = {
.destroy = my3126_destroy,
.reset = my3126_reset,
.interrupt_enable = my3126_interrupt_enable,
.interrupt_disable = my3126_interrupt_disable,
.interrupt_clear = my3126_interrupt_clear,
.interrupt_handler = my3126_interrupt_handler,
.get_link_status = my3126_get_link_status,
.set_loopback = my3126_set_loopback,
.mmds = (MDIO_DEVS_PMAPMD | MDIO_DEVS_PCS |
MDIO_DEVS_PHYXS),
};
static struct cphy *my3126_phy_create(struct net_device *dev,
int phy_addr, const struct mdio_ops *mdio_ops)
{
struct cphy *cphy = kzalloc(sizeof (*cphy), GFP_KERNEL);
if (!cphy)
return NULL;
cphy_init(cphy, dev, phy_addr, &my3126_ops, mdio_ops);
INIT_DELAYED_WORK(&cphy->phy_update, my3126_poll);
cphy->bmsr = 0;
return cphy;
}
/* Chip Reset */
static int my3126_phy_reset(adapter_t * adapter)
{
u32 val;
t1_tpi_read(adapter, A_ELMER0_GPO, &val);
val &= ~4;
t1_tpi_write(adapter, A_ELMER0_GPO, val);
msleep(100);
t1_tpi_write(adapter, A_ELMER0_GPO, val | 4);
msleep(1000);
/* Now lets enable the Laser. Delay 100us */
t1_tpi_read(adapter, A_ELMER0_GPO, &val);
val |= 0x8000;
t1_tpi_write(adapter, A_ELMER0_GPO, val);
udelay(100);
return 0;
}
const struct gphy t1_my3126_ops = {
.create = my3126_phy_create,
.reset = my3126_phy_reset
};