| Author | Tokens | Token Proportion | Commits | Commit Proportion |
|---|---|---|---|---|
| Benjamin Herrenschmidt | 1644 | 100.00% | 4 | 100.00% |
| Total | 1644 | 4 |
/* SPDX-License-Identifier: GPL-2.0+ */ #ifndef __ASPEED_VHUB_H #define __ASPEED_VHUB_H /***************************** * * * VHUB register definitions * * * *****************************/ #define AST_VHUB_CTRL 0x00 /* Root Function Control & Status Register */ #define AST_VHUB_CONF 0x04 /* Root Configuration Setting Register */ #define AST_VHUB_IER 0x08 /* Interrupt Ctrl Register */ #define AST_VHUB_ISR 0x0C /* Interrupt Status Register */ #define AST_VHUB_EP_ACK_IER 0x10 /* Programmable Endpoint Pool ACK Interrupt Enable Register */ #define AST_VHUB_EP_NACK_IER 0x14 /* Programmable Endpoint Pool NACK Interrupt Enable Register */ #define AST_VHUB_EP_ACK_ISR 0x18 /* Programmable Endpoint Pool ACK Interrupt Status Register */ #define AST_VHUB_EP_NACK_ISR 0x1C /* Programmable Endpoint Pool NACK Interrupt Status Register */ #define AST_VHUB_SW_RESET 0x20 /* Device Controller Soft Reset Enable Register */ #define AST_VHUB_USBSTS 0x24 /* USB Status Register */ #define AST_VHUB_EP_TOGGLE 0x28 /* Programmable Endpoint Pool Data Toggle Value Set */ #define AST_VHUB_ISO_FAIL_ACC 0x2C /* Isochronous Transaction Fail Accumulator */ #define AST_VHUB_EP0_CTRL 0x30 /* Endpoint 0 Contrl/Status Register */ #define AST_VHUB_EP0_DATA 0x34 /* Base Address of Endpoint 0 In/OUT Data Buffer Register */ #define AST_VHUB_EP1_CTRL 0x38 /* Endpoint 1 Contrl/Status Register */ #define AST_VHUB_EP1_STS_CHG 0x3C /* Endpoint 1 Status Change Bitmap Data */ #define AST_VHUB_SETUP0 0x80 /* Root Device Setup Data Buffer0 */ #define AST_VHUB_SETUP1 0x84 /* Root Device Setup Data Buffer1 */ /* Main control reg */ #define VHUB_CTRL_PHY_CLK (1 << 31) #define VHUB_CTRL_PHY_LOOP_TEST (1 << 25) #define VHUB_CTRL_DN_PWN (1 << 24) #define VHUB_CTRL_DP_PWN (1 << 23) #define VHUB_CTRL_LONG_DESC (1 << 18) #define VHUB_CTRL_ISO_RSP_CTRL (1 << 17) #define VHUB_CTRL_SPLIT_IN (1 << 16) #define VHUB_CTRL_LOOP_T_RESULT (1 << 15) #define VHUB_CTRL_LOOP_T_STS (1 << 14) #define VHUB_CTRL_PHY_BIST_RESULT (1 << 13) #define VHUB_CTRL_PHY_BIST_CTRL (1 << 12) #define VHUB_CTRL_PHY_RESET_DIS (1 << 11) #define VHUB_CTRL_SET_TEST_MODE(x) ((x) << 8) #define VHUB_CTRL_MANUAL_REMOTE_WAKEUP (1 << 4) #define VHUB_CTRL_AUTO_REMOTE_WAKEUP (1 << 3) #define VHUB_CTRL_CLK_STOP_SUSPEND (1 << 2) #define VHUB_CTRL_FULL_SPEED_ONLY (1 << 1) #define VHUB_CTRL_UPSTREAM_CONNECT (1 << 0) /* IER & ISR */ #define VHUB_IRQ_USB_CMD_DEADLOCK (1 << 18) #define VHUB_IRQ_EP_POOL_NAK (1 << 17) #define VHUB_IRQ_EP_POOL_ACK_STALL (1 << 16) #define VHUB_IRQ_DEVICE5 (1 << 13) #define VHUB_IRQ_DEVICE4 (1 << 12) #define VHUB_IRQ_DEVICE3 (1 << 11) #define VHUB_IRQ_DEVICE2 (1 << 10) #define VHUB_IRQ_DEVICE1 (1 << 9) #define VHUB_IRQ_BUS_RESUME (1 << 8) #define VHUB_IRQ_BUS_SUSPEND (1 << 7) #define VHUB_IRQ_BUS_RESET (1 << 6) #define VHUB_IRQ_HUB_EP1_IN_DATA_ACK (1 << 5) #define VHUB_IRQ_HUB_EP0_IN_DATA_NAK (1 << 4) #define VHUB_IRQ_HUB_EP0_IN_ACK_STALL (1 << 3) #define VHUB_IRQ_HUB_EP0_OUT_NAK (1 << 2) #define VHUB_IRQ_HUB_EP0_OUT_ACK_STALL (1 << 1) #define VHUB_IRQ_HUB_EP0_SETUP (1 << 0) #define VHUB_IRQ_ACK_ALL 0x1ff /* SW reset reg */ #define VHUB_SW_RESET_EP_POOL (1 << 9) #define VHUB_SW_RESET_DMA_CONTROLLER (1 << 8) #define VHUB_SW_RESET_DEVICE5 (1 << 5) #define VHUB_SW_RESET_DEVICE4 (1 << 4) #define VHUB_SW_RESET_DEVICE3 (1 << 3) #define VHUB_SW_RESET_DEVICE2 (1 << 2) #define VHUB_SW_RESET_DEVICE1 (1 << 1) #define VHUB_SW_RESET_ROOT_HUB (1 << 0) #define VHUB_SW_RESET_ALL (VHUB_SW_RESET_EP_POOL | \ VHUB_SW_RESET_DMA_CONTROLLER | \ VHUB_SW_RESET_DEVICE5 | \ VHUB_SW_RESET_DEVICE4 | \ VHUB_SW_RESET_DEVICE3 | \ VHUB_SW_RESET_DEVICE2 | \ VHUB_SW_RESET_DEVICE1 | \ VHUB_SW_RESET_ROOT_HUB) /* EP ACK/NACK IRQ masks */ #define VHUB_EP_IRQ(n) (1 << (n)) #define VHUB_EP_IRQ_ALL 0x7fff /* 15 EPs */ /* USB status reg */ #define VHUB_USBSTS_HISPEED (1 << 27) /* EP toggle */ #define VHUB_EP_TOGGLE_VALUE (1 << 8) #define VHUB_EP_TOGGLE_SET_EPNUM(x) ((x) & 0x1f) /* HUB EP0 control */ #define VHUB_EP0_CTRL_STALL (1 << 0) #define VHUB_EP0_TX_BUFF_RDY (1 << 1) #define VHUB_EP0_RX_BUFF_RDY (1 << 2) #define VHUB_EP0_RX_LEN(x) (((x) >> 16) & 0x7f) #define VHUB_EP0_SET_TX_LEN(x) (((x) & 0x7f) << 8) /* HUB EP1 control */ #define VHUB_EP1_CTRL_RESET_TOGGLE (1 << 2) #define VHUB_EP1_CTRL_STALL (1 << 1) #define VHUB_EP1_CTRL_ENABLE (1 << 0) /*********************************** * * * per-device register definitions * * * ***********************************/ #define AST_VHUB_DEV_EN_CTRL 0x00 #define AST_VHUB_DEV_ISR 0x04 #define AST_VHUB_DEV_EP0_CTRL 0x08 #define AST_VHUB_DEV_EP0_DATA 0x0c /* Device enable control */ #define VHUB_DEV_EN_SET_ADDR(x) ((x) << 8) #define VHUB_DEV_EN_ADDR_MASK ((0xff) << 8) #define VHUB_DEV_EN_EP0_NAK_IRQEN (1 << 6) #define VHUB_DEV_EN_EP0_IN_ACK_IRQEN (1 << 5) #define VHUB_DEV_EN_EP0_OUT_NAK_IRQEN (1 << 4) #define VHUB_DEV_EN_EP0_OUT_ACK_IRQEN (1 << 3) #define VHUB_DEV_EN_EP0_SETUP_IRQEN (1 << 2) #define VHUB_DEV_EN_SPEED_SEL_HIGH (1 << 1) #define VHUB_DEV_EN_ENABLE_PORT (1 << 0) /* Interrupt status */ #define VHUV_DEV_IRQ_EP0_IN_DATA_NACK (1 << 4) #define VHUV_DEV_IRQ_EP0_IN_ACK_STALL (1 << 3) #define VHUV_DEV_IRQ_EP0_OUT_DATA_NACK (1 << 2) #define VHUV_DEV_IRQ_EP0_OUT_ACK_STALL (1 << 1) #define VHUV_DEV_IRQ_EP0_SETUP (1 << 0) /* Control bits. * * Note: The driver relies on the bulk of those bits * matching corresponding vHub EP0 control bits */ #define VHUB_DEV_EP0_CTRL_STALL VHUB_EP0_CTRL_STALL #define VHUB_DEV_EP0_TX_BUFF_RDY VHUB_EP0_TX_BUFF_RDY #define VHUB_DEV_EP0_RX_BUFF_RDY VHUB_EP0_RX_BUFF_RDY #define VHUB_DEV_EP0_RX_LEN(x) VHUB_EP0_RX_LEN(x) #define VHUB_DEV_EP0_SET_TX_LEN(x) VHUB_EP0_SET_TX_LEN(x) /************************************* * * * per-endpoint register definitions * * * *************************************/ #define AST_VHUB_EP_CONFIG 0x00 #define AST_VHUB_EP_DMA_CTLSTAT 0x04 #define AST_VHUB_EP_DESC_BASE 0x08 #define AST_VHUB_EP_DESC_STATUS 0x0C /* EP config reg */ #define VHUB_EP_CFG_SET_MAX_PKT(x) (((x) & 0x3ff) << 16) #define VHUB_EP_CFG_AUTO_DATA_DISABLE (1 << 13) #define VHUB_EP_CFG_STALL_CTRL (1 << 12) #define VHUB_EP_CFG_SET_EP_NUM(x) (((x) & 0xf) << 8) #define VHUB_EP_CFG_SET_TYPE(x) ((x) << 5) #define EP_TYPE_OFF 0 #define EP_TYPE_BULK 1 #define EP_TYPE_INT 2 #define EP_TYPE_ISO 3 #define VHUB_EP_CFG_DIR_OUT (1 << 4) #define VHUB_EP_CFG_SET_DEV(x) ((x) << 1) #define VHUB_EP_CFG_ENABLE (1 << 0) /* EP DMA control */ #define VHUB_EP_DMA_PROC_STATUS(x) (((x) >> 4) & 0xf) #define EP_DMA_PROC_RX_IDLE 0 #define EP_DMA_PROC_TX_IDLE 8 #define VHUB_EP_DMA_IN_LONG_MODE (1 << 3) #define VHUB_EP_DMA_OUT_CONTIG_MODE (1 << 3) #define VHUB_EP_DMA_CTRL_RESET (1 << 2) #define VHUB_EP_DMA_SINGLE_STAGE (1 << 1) #define VHUB_EP_DMA_DESC_MODE (1 << 0) /* EP DMA status */ #define VHUB_EP_DMA_SET_TX_SIZE(x) ((x) << 16) #define VHUB_EP_DMA_TX_SIZE(x) (((x) >> 16) & 0x7ff) #define VHUB_EP_DMA_RPTR(x) (((x) >> 8) & 0xff) #define VHUB_EP_DMA_SET_RPTR(x) (((x) & 0xff) << 8) #define VHUB_EP_DMA_SET_CPU_WPTR(x) (x) #define VHUB_EP_DMA_SINGLE_KICK (1 << 0) /* WPTR = 1 for single mode */ /******************************* * * * DMA descriptors definitions * * * *******************************/ /* Desc W1 IN */ #define VHUB_DSC1_IN_INTERRUPT (1 << 31) #define VHUB_DSC1_IN_SPID_DATA0 (0 << 14) #define VHUB_DSC1_IN_SPID_DATA2 (1 << 14) #define VHUB_DSC1_IN_SPID_DATA1 (2 << 14) #define VHUB_DSC1_IN_SPID_MDATA (3 << 14) #define VHUB_DSC1_IN_SET_LEN(x) ((x) & 0xfff) #define VHUB_DSC1_IN_LEN(x) ((x) & 0xfff) /**************************************** * * * Data structures and misc definitions * * * ****************************************/ #define AST_VHUB_NUM_GEN_EPs 15 /* Generic non-0 EPs */ #define AST_VHUB_NUM_PORTS 5 /* vHub ports */ #define AST_VHUB_EP0_MAX_PACKET 64 /* EP0's max packet size */ #define AST_VHUB_EPn_MAX_PACKET 1024 /* Generic EPs max packet size */ #define AST_VHUB_DESCS_COUNT 256 /* Use 256 descriptor mode (valid * values are 256 and 32) */ struct ast_vhub; struct ast_vhub_dev; /* * DMA descriptor (generic EPs only, currently only used * for IN endpoints */ struct ast_vhub_desc { __le32 w0; __le32 w1; }; /* A transfer request, either core-originated or internal */ struct ast_vhub_req { struct usb_request req; struct list_head queue; /* Actual count written to descriptors (desc mode only) */ unsigned int act_count; /* * Desc number of the final packet or -1. For non-desc * mode (or ep0), any >= 0 value means "last packet" */ int last_desc; /* Request active (pending DMAs) */ bool active : 1; /* Internal request (don't call back core) */ bool internal : 1; }; #define to_ast_req(__ureq) container_of(__ureq, struct ast_vhub_req, req) /* Current state of an EP0 */ enum ep0_state { ep0_state_token, ep0_state_data, ep0_state_status, ep0_state_stall, }; /* * An endpoint, either generic, ep0, actual gadget EP * or internal use vhub EP0. vhub EP1 doesn't have an * associated structure as it's mostly HW managed. */ struct ast_vhub_ep { struct usb_ep ep; /* Request queue */ struct list_head queue; /* EP index in the device, 0 means this is an EP0 */ unsigned int d_idx; /* Dev pointer or NULL for vHub EP0 */ struct ast_vhub_dev *dev; /* vHub itself */ struct ast_vhub *vhub; /* * DMA buffer for EP0, fallback DMA buffer for misaligned * OUT transfers for generic EPs */ void *buf; dma_addr_t buf_dma; /* The rest depends on the EP type */ union { /* EP0 (either device or vhub) */ struct { /* * EP0 registers are "similar" for * vHub and devices but located in * different places. */ void __iomem *ctlstat; void __iomem *setup; /* Current state & direction */ enum ep0_state state; bool dir_in; /* Internal use request */ struct ast_vhub_req req; } ep0; /* Generic endpoint (aka EPn) */ struct { /* Registers */ void __iomem *regs; /* Index in global pool (0..14) */ unsigned int g_idx; /* DMA Descriptors */ struct ast_vhub_desc *descs; dma_addr_t descs_dma; unsigned int d_next; unsigned int d_last; unsigned int dma_conf; /* Max chunk size for IN EPs */ unsigned int chunk_max; /* State flags */ bool is_in : 1; bool is_iso : 1; bool stalled : 1; bool wedged : 1; bool enabled : 1; bool desc_mode : 1; } epn; }; }; #define to_ast_ep(__uep) container_of(__uep, struct ast_vhub_ep, ep) /* A device attached to a vHub port */ struct ast_vhub_dev { struct ast_vhub *vhub; void __iomem *regs; /* Device index (0...4) and name string */ unsigned int index; const char *name; /* sysfs enclosure for the gadget gunk */ struct device *port_dev; /* Link to gadget core */ struct usb_gadget gadget; struct usb_gadget_driver *driver; bool registered : 1; bool wakeup_en : 1; bool enabled : 1; /* Endpoint structures */ struct ast_vhub_ep ep0; struct ast_vhub_ep *epns[AST_VHUB_NUM_GEN_EPs]; }; #define to_ast_dev(__g) container_of(__g, struct ast_vhub_dev, gadget) /* Per vhub port stateinfo structure */ struct ast_vhub_port { /* Port status & status change registers */ u16 status; u16 change; /* Associated device slot */ struct ast_vhub_dev dev; }; /* Global vhub structure */ struct ast_vhub { struct platform_device *pdev; void __iomem *regs; int irq; spinlock_t lock; struct work_struct wake_work; struct clk *clk; /* EP0 DMA buffers allocated in one chunk */ void *ep0_bufs; dma_addr_t ep0_bufs_dma; /* EP0 of the vhub itself */ struct ast_vhub_ep ep0; /* State of vhub ep1 */ bool ep1_stalled : 1; /* Per-port info */ struct ast_vhub_port ports[AST_VHUB_NUM_PORTS]; /* Generic EP data structures */ struct ast_vhub_ep epns[AST_VHUB_NUM_GEN_EPs]; /* Upstream bus is suspended ? */ bool suspended : 1; /* Hub itself can signal remote wakeup */ bool wakeup_en : 1; /* Force full speed only */ bool force_usb1 : 1; /* Upstream bus speed captured at bus reset */ unsigned int speed; }; /* Standard request handlers result codes */ enum std_req_rc { std_req_stall = -1, /* Stall requested */ std_req_complete = 0, /* Request completed with no data */ std_req_data = 1, /* Request completed with data */ std_req_driver = 2, /* Pass to driver pls */ }; #ifdef CONFIG_USB_GADGET_VERBOSE #define UDCVDBG(u, fmt...) dev_dbg(&(u)->pdev->dev, fmt) #define EPVDBG(ep, fmt, ...) do { \ dev_dbg(&(ep)->vhub->pdev->dev, \ "%s:EP%d " fmt, \ (ep)->dev ? (ep)->dev->name : "hub", \ (ep)->d_idx, ##__VA_ARGS__); \ } while(0) #define DVDBG(d, fmt, ...) do { \ dev_dbg(&(d)->vhub->pdev->dev, \ "%s " fmt, (d)->name, \ ##__VA_ARGS__); \ } while(0) #else #define UDCVDBG(u, fmt...) do { } while(0) #define EPVDBG(ep, fmt, ...) do { } while(0) #define DVDBG(d, fmt, ...) do { } while(0) #endif #ifdef CONFIG_USB_GADGET_DEBUG #define UDCDBG(u, fmt...) dev_dbg(&(u)->pdev->dev, fmt) #define EPDBG(ep, fmt, ...) do { \ dev_dbg(&(ep)->vhub->pdev->dev, \ "%s:EP%d " fmt, \ (ep)->dev ? (ep)->dev->name : "hub", \ (ep)->d_idx, ##__VA_ARGS__); \ } while(0) #define DDBG(d, fmt, ...) do { \ dev_dbg(&(d)->vhub->pdev->dev, \ "%s " fmt, (d)->name, \ ##__VA_ARGS__); \ } while(0) #else #define UDCDBG(u, fmt...) do { } while(0) #define EPDBG(ep, fmt, ...) do { } while(0) #define DDBG(d, fmt, ...) do { } while(0) #endif static inline void vhub_dma_workaround(void *addr) { /* * This works around a confirmed HW issue with the Aspeed chip. * * The core uses a different bus to memory than the AHB going to * the USB device controller. Due to the latter having a higher * priority than the core for arbitration on that bus, it's * possible for an MMIO to the device, followed by a DMA by the * device from memory to all be performed and services before * a previous store to memory gets completed. * * This the following scenario can happen: * * - Driver writes to a DMA descriptor (Mbus) * - Driver writes to the MMIO register to start the DMA (AHB) * - The gadget sees the second write and sends a read of the * descriptor to the memory controller (Mbus) * - The gadget hits memory before the descriptor write * causing it to read an obsolete value. * * Thankfully the problem is limited to the USB gadget device, other * masters in the SoC all have a lower priority than the core, thus * ensuring that the store by the core arrives first. * * The workaround consists of using a dummy read of the memory before * doing the MMIO writes. This will ensure that the previous writes * have been "pushed out". */ mb(); (void)__raw_readl((void __iomem *)addr); } /* core.c */ void ast_vhub_done(struct ast_vhub_ep *ep, struct ast_vhub_req *req, int status); void ast_vhub_nuke(struct ast_vhub_ep *ep, int status); struct usb_request *ast_vhub_alloc_request(struct usb_ep *u_ep, gfp_t gfp_flags); void ast_vhub_free_request(struct usb_ep *u_ep, struct usb_request *u_req); void ast_vhub_init_hw(struct ast_vhub *vhub); /* ep0.c */ void ast_vhub_ep0_handle_ack(struct ast_vhub_ep *ep, bool in_ack); void ast_vhub_ep0_handle_setup(struct ast_vhub_ep *ep); void ast_vhub_reset_ep0(struct ast_vhub_dev *dev); void ast_vhub_init_ep0(struct ast_vhub *vhub, struct ast_vhub_ep *ep, struct ast_vhub_dev *dev); int ast_vhub_reply(struct ast_vhub_ep *ep, char *ptr, int len); int __ast_vhub_simple_reply(struct ast_vhub_ep *ep, int len, ...); #define ast_vhub_simple_reply(udc, ...) \ __ast_vhub_simple_reply((udc), \ sizeof((u8[]) { __VA_ARGS__ })/sizeof(u8), \ __VA_ARGS__) /* hub.c */ void ast_vhub_init_hub(struct ast_vhub *vhub); enum std_req_rc ast_vhub_std_hub_request(struct ast_vhub_ep *ep, struct usb_ctrlrequest *crq); enum std_req_rc ast_vhub_class_hub_request(struct ast_vhub_ep *ep, struct usb_ctrlrequest *crq); void ast_vhub_device_connect(struct ast_vhub *vhub, unsigned int port, bool on); void ast_vhub_hub_suspend(struct ast_vhub *vhub); void ast_vhub_hub_resume(struct ast_vhub *vhub); void ast_vhub_hub_reset(struct ast_vhub *vhub); void ast_vhub_hub_wake_all(struct ast_vhub *vhub); /* dev.c */ int ast_vhub_init_dev(struct ast_vhub *vhub, unsigned int idx); void ast_vhub_del_dev(struct ast_vhub_dev *d); void ast_vhub_dev_irq(struct ast_vhub_dev *d); int ast_vhub_std_dev_request(struct ast_vhub_ep *ep, struct usb_ctrlrequest *crq); /* epn.c */ void ast_vhub_epn_ack_irq(struct ast_vhub_ep *ep); void ast_vhub_update_epn_stall(struct ast_vhub_ep *ep); struct ast_vhub_ep *ast_vhub_alloc_epn(struct ast_vhub_dev *d, u8 addr); void ast_vhub_dev_suspend(struct ast_vhub_dev *d); void ast_vhub_dev_resume(struct ast_vhub_dev *d); void ast_vhub_dev_reset(struct ast_vhub_dev *d); #endif /* __ASPEED_VHUB_H */
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.
Created with Cregit http://github.com/cregit/cregit
Version 2.0-RC1