Contributors: 3
Author Tokens Token Proportion Commits Commit Proportion
Matti Vaittinen 5684 98.54% 16 64.00%
Axel Lin 79 1.37% 8 32.00%
Guido Günther 5 0.09% 1 4.00%
Total 5768 25 


// SPDX-License-Identifier: GPL-2.0
// Copyright (C) 2018 ROHM Semiconductors
// bd71837-regulator.c ROHM BD71837MWV/BD71847MWV regulator driver

#include <linux/delay.h>
#include <linux/err.h>
#include <linux/interrupt.h>
#include <linux/kernel.h>
#include <linux/mfd/rohm-bd718x7.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/platform_device.h>
#include <linux/regulator/driver.h>
#include <linux/regulator/machine.h>
#include <linux/regulator/of_regulator.h>
#include <linux/slab.h>

/*
 * BUCK1/2/3/4
 * BUCK1RAMPRATE[1:0] BUCK1 DVS ramp rate setting
 * 00: 10.00mV/usec 10mV 1uS
 * 01: 5.00mV/usec	10mV 2uS
 * 10: 2.50mV/usec	10mV 4uS
 * 11: 1.25mV/usec	10mV 8uS
 */
static int bd718xx_buck1234_set_ramp_delay(struct regulator_dev *rdev,
					   int ramp_delay)
{
	int id = rdev_get_id(rdev);
	unsigned int ramp_value;

	dev_dbg(&rdev->dev, "Buck[%d] Set Ramp = %d\n", id + 1,
		ramp_delay);
	switch (ramp_delay) {
	case 1 ... 1250:
		ramp_value = BUCK_RAMPRATE_1P25MV;
		break;
	case 1251 ... 2500:
		ramp_value = BUCK_RAMPRATE_2P50MV;
		break;
	case 2501 ... 5000:
		ramp_value = BUCK_RAMPRATE_5P00MV;
		break;
	case 5001 ... 10000:
		ramp_value = BUCK_RAMPRATE_10P00MV;
		break;
	default:
		ramp_value = BUCK_RAMPRATE_10P00MV;
		dev_err(&rdev->dev,
			"%s: ramp_delay: %d not supported, setting 10000mV//us\n",
			rdev->desc->name, ramp_delay);
	}

	return regmap_update_bits(rdev->regmap, BD718XX_REG_BUCK1_CTRL + id,
				  BUCK_RAMPRATE_MASK, ramp_value << 6);
}

/*
 * On BD71837 (not on BD71847, BD71850, ...)
 * Bucks 1 to 4 support DVS. PWM mode is used when voltage is changed.
 * Bucks 5 to 8 and LDOs can use PFM and must be disabled when voltage
 * is changed. Hence we return -EBUSY for these if voltage is changed
 * when BUCK/LDO is enabled.
 *
 * On BD71847, BD71850, ... The LDO voltage can be changed when LDO is
 * enabled. But if voltage is increased the LDO power-good monitoring
 * must be disabled for the duration of changing + 1mS to ensure voltage
 * has reached the higher level before HW does next under voltage detection
 * cycle.
 */
static int bd71837_set_voltage_sel_restricted(struct regulator_dev *rdev,
						    unsigned int sel)
{
	if (regulator_is_enabled_regmap(rdev))
		return -EBUSY;

	return regulator_set_voltage_sel_regmap(rdev, sel);
}

static void voltage_change_done(struct regulator_dev *rdev, unsigned int sel,
				unsigned int *mask)
{
	int ret;

	if (*mask) {
		/*
		 * Let's allow scheduling as we use I2C anyways. We just need to
		 * guarantee minimum of 1ms sleep - it shouldn't matter if we
		 * exceed it due to the scheduling.
		 */
		msleep(1);
		/*
		 * Note for next hacker. The PWRGOOD should not be masked on
		 * BD71847 so we will just unconditionally enable detection
		 * when voltage is set.
		 * If someone want's to disable PWRGOOD he must implement
		 * caching and restoring the old value here. I am not
		 * aware of such use-cases so for the sake of the simplicity
		 * we just always enable PWRGOOD here.
		 */
		ret = regmap_update_bits(rdev->regmap, BD718XX_REG_MVRFLTMASK2,
					 *mask, 0);
		if (ret)
			dev_err(&rdev->dev,
				"Failed to re-enable voltage monitoring (%d)\n",
				ret);
	}
}

static int voltage_change_prepare(struct regulator_dev *rdev, unsigned int sel,
				  unsigned int *mask)
{
	int ret;

	*mask = 0;
	if (regulator_is_enabled_regmap(rdev)) {
		int now, new;

		now = rdev->desc->ops->get_voltage_sel(rdev);
		if (now < 0)
			return now;

		now = rdev->desc->ops->list_voltage(rdev, now);
		if (now < 0)
			return now;

		new = rdev->desc->ops->list_voltage(rdev, sel);
		if (new < 0)
			return new;

		/*
		 * If we increase LDO voltage when LDO is enabled we need to
		 * disable the power-good detection until voltage has reached
		 * the new level. According to HW colleagues the maximum time
		 * it takes is 1000us. I assume that on systems with light load
		 * this might be less - and we could probably use DT to give
		 * system specific delay value if performance matters.
		 *
		 * Well, knowing we use I2C here and can add scheduling delays
		 * I don't think it is worth the hassle and I just add fixed
		 * 1ms sleep here (and allow scheduling). If this turns out to
		 * be a problem we can change it to delay and make the delay
		 * time configurable.
		 */
		if (new > now) {
			int ldo_offset = rdev->desc->id - BD718XX_LDO1;

			*mask = BD718XX_LDO1_VRMON80 << ldo_offset;
			ret = regmap_update_bits(rdev->regmap,
						 BD718XX_REG_MVRFLTMASK2,
						 *mask, *mask);
			if (ret) {
				dev_err(&rdev->dev,
					"Failed to stop voltage monitoring\n");
				return ret;
			}
		}
	}

	return 0;
}

static int bd718xx_set_voltage_sel_restricted(struct regulator_dev *rdev,
						    unsigned int sel)
{
	int ret;
	int mask;

	ret = voltage_change_prepare(rdev, sel, &mask);
	if (ret)
		return ret;

	ret = regulator_set_voltage_sel_regmap(rdev, sel);
	voltage_change_done(rdev, sel, &mask);

	return ret;
}

static int bd718xx_set_voltage_sel_pickable_restricted(
		struct regulator_dev *rdev, unsigned int sel)
{
	int ret;
	int mask;

	ret = voltage_change_prepare(rdev, sel, &mask);
	if (ret)
		return ret;

	ret = regulator_set_voltage_sel_pickable_regmap(rdev, sel);
	voltage_change_done(rdev, sel, &mask);

	return ret;
}

static int bd71837_set_voltage_sel_pickable_restricted(
		struct regulator_dev *rdev, unsigned int sel)
{
	if (regulator_is_enabled_regmap(rdev))
		return -EBUSY;

	return regulator_set_voltage_sel_pickable_regmap(rdev, sel);
}

static const struct regulator_ops bd718xx_pickable_range_ldo_ops = {
	.enable = regulator_enable_regmap,
	.disable = regulator_disable_regmap,
	.is_enabled = regulator_is_enabled_regmap,
	.list_voltage = regulator_list_voltage_pickable_linear_range,
	.set_voltage_sel = bd718xx_set_voltage_sel_pickable_restricted,
	.get_voltage_sel = regulator_get_voltage_sel_pickable_regmap,

};

static const struct regulator_ops bd71837_pickable_range_ldo_ops = {
	.enable = regulator_enable_regmap,
	.disable = regulator_disable_regmap,
	.is_enabled = regulator_is_enabled_regmap,
	.list_voltage = regulator_list_voltage_pickable_linear_range,
	.set_voltage_sel = bd71837_set_voltage_sel_pickable_restricted,
	.get_voltage_sel = regulator_get_voltage_sel_pickable_regmap,
};

static const struct regulator_ops bd718xx_pickable_range_buck_ops = {
	.enable = regulator_enable_regmap,
	.disable = regulator_disable_regmap,
	.is_enabled = regulator_is_enabled_regmap,
	.list_voltage = regulator_list_voltage_pickable_linear_range,
	.set_voltage_sel = regulator_set_voltage_sel_pickable_regmap,
	.get_voltage_sel = regulator_get_voltage_sel_pickable_regmap,
	.set_voltage_time_sel = regulator_set_voltage_time_sel,
};

static const struct regulator_ops bd71837_pickable_range_buck_ops = {
	.enable = regulator_enable_regmap,
	.disable = regulator_disable_regmap,
	.is_enabled = regulator_is_enabled_regmap,
	.list_voltage = regulator_list_voltage_pickable_linear_range,
	.set_voltage_sel = bd71837_set_voltage_sel_pickable_restricted,
	.get_voltage_sel = regulator_get_voltage_sel_pickable_regmap,
	.set_voltage_time_sel = regulator_set_voltage_time_sel,
};

static const struct regulator_ops bd71837_ldo_regulator_ops = {
	.enable = regulator_enable_regmap,
	.disable = regulator_disable_regmap,
	.is_enabled = regulator_is_enabled_regmap,
	.list_voltage = regulator_list_voltage_linear_range,
	.set_voltage_sel = bd71837_set_voltage_sel_restricted,
	.get_voltage_sel = regulator_get_voltage_sel_regmap,
};

static const struct regulator_ops bd718xx_ldo_regulator_ops = {
	.enable = regulator_enable_regmap,
	.disable = regulator_disable_regmap,
	.is_enabled = regulator_is_enabled_regmap,
	.list_voltage = regulator_list_voltage_linear_range,
	.set_voltage_sel = bd718xx_set_voltage_sel_restricted,
	.get_voltage_sel = regulator_get_voltage_sel_regmap,
};

static const struct regulator_ops bd71837_ldo_regulator_nolinear_ops = {
	.enable = regulator_enable_regmap,
	.disable = regulator_disable_regmap,
	.is_enabled = regulator_is_enabled_regmap,
	.list_voltage = regulator_list_voltage_table,
	.set_voltage_sel = bd71837_set_voltage_sel_restricted,
	.get_voltage_sel = regulator_get_voltage_sel_regmap,
};

static const struct regulator_ops bd718xx_ldo_regulator_nolinear_ops = {
	.enable = regulator_enable_regmap,
	.disable = regulator_disable_regmap,
	.is_enabled = regulator_is_enabled_regmap,
	.list_voltage = regulator_list_voltage_table,
	.set_voltage_sel = bd718xx_set_voltage_sel_restricted,
	.get_voltage_sel = regulator_get_voltage_sel_regmap,
};

static const struct regulator_ops bd718xx_buck_regulator_ops = {
	.enable = regulator_enable_regmap,
	.disable = regulator_disable_regmap,
	.is_enabled = regulator_is_enabled_regmap,
	.list_voltage = regulator_list_voltage_linear_range,
	.set_voltage_sel = regulator_set_voltage_sel_regmap,
	.get_voltage_sel = regulator_get_voltage_sel_regmap,
	.set_voltage_time_sel = regulator_set_voltage_time_sel,
};

static const struct regulator_ops bd71837_buck_regulator_ops = {
	.enable = regulator_enable_regmap,
	.disable = regulator_disable_regmap,
	.is_enabled = regulator_is_enabled_regmap,
	.list_voltage = regulator_list_voltage_linear_range,
	.set_voltage_sel = bd71837_set_voltage_sel_restricted,
	.get_voltage_sel = regulator_get_voltage_sel_regmap,
	.set_voltage_time_sel = regulator_set_voltage_time_sel,
};

static const struct regulator_ops bd718xx_buck_regulator_nolinear_ops = {
	.enable = regulator_enable_regmap,
	.disable = regulator_disable_regmap,
	.is_enabled = regulator_is_enabled_regmap,
	.list_voltage = regulator_list_voltage_table,
	.map_voltage = regulator_map_voltage_ascend,
	.set_voltage_sel = regulator_set_voltage_sel_regmap,
	.get_voltage_sel = regulator_get_voltage_sel_regmap,
	.set_voltage_time_sel = regulator_set_voltage_time_sel,
};

static const struct regulator_ops bd71837_buck_regulator_nolinear_ops = {
	.enable = regulator_enable_regmap,
	.disable = regulator_disable_regmap,
	.is_enabled = regulator_is_enabled_regmap,
	.list_voltage = regulator_list_voltage_table,
	.map_voltage = regulator_map_voltage_ascend,
	.set_voltage_sel = bd718xx_set_voltage_sel_restricted,
	.get_voltage_sel = regulator_get_voltage_sel_regmap,
	.set_voltage_time_sel = regulator_set_voltage_time_sel,
};

static const struct regulator_ops bd718xx_dvs_buck_regulator_ops = {
	.enable = regulator_enable_regmap,
	.disable = regulator_disable_regmap,
	.is_enabled = regulator_is_enabled_regmap,
	.list_voltage = regulator_list_voltage_linear_range,
	.set_voltage_sel = regulator_set_voltage_sel_regmap,
	.get_voltage_sel = regulator_get_voltage_sel_regmap,
	.set_voltage_time_sel = regulator_set_voltage_time_sel,
	.set_ramp_delay = bd718xx_buck1234_set_ramp_delay,
};

/*
 * BD71837 BUCK1/2/3/4
 * BD71847 BUCK1/2
 * 0.70 to 1.30V (10mV step)
 */
static const struct linear_range bd718xx_dvs_buck_volts[] = {
	REGULATOR_LINEAR_RANGE(700000, 0x00, 0x3C, 10000),
	REGULATOR_LINEAR_RANGE(1300000, 0x3D, 0x3F, 0),
};

/*
 * BD71837 BUCK5
 * 0.7V to 1.35V  (range 0)
 * and
 * 0.675 to 1.325 (range 1)
 */
static const struct linear_range bd71837_buck5_volts[] = {
	/* Ranges when VOLT_SEL bit is 0 */
	REGULATOR_LINEAR_RANGE(700000, 0x00, 0x03, 100000),
	REGULATOR_LINEAR_RANGE(1050000, 0x04, 0x05, 50000),
	REGULATOR_LINEAR_RANGE(1200000, 0x06, 0x07, 150000),
	/* Ranges when VOLT_SEL bit is 1  */
	REGULATOR_LINEAR_RANGE(675000, 0x0, 0x3, 100000),
	REGULATOR_LINEAR_RANGE(1025000, 0x4, 0x5, 50000),
	REGULATOR_LINEAR_RANGE(1175000, 0x6, 0x7, 150000),
};

/*
 * Range selector for first 3 linear ranges is 0x0
 * and 0x1 for last 3 ranges.
 */
static const unsigned int bd71837_buck5_volt_range_sel[] = {
	0x0, 0x0, 0x0, 0x80, 0x80, 0x80
};

/*
 * BD71847 BUCK3
 */
static const struct linear_range bd71847_buck3_volts[] = {
	/* Ranges when VOLT_SEL bits are 00 */
	REGULATOR_LINEAR_RANGE(700000, 0x00, 0x03, 100000),
	REGULATOR_LINEAR_RANGE(1050000, 0x04, 0x05, 50000),
	REGULATOR_LINEAR_RANGE(1200000, 0x06, 0x07, 150000),
	/* Ranges when VOLT_SEL bits are 01 */
	REGULATOR_LINEAR_RANGE(550000, 0x0, 0x7, 50000),
	/* Ranges when VOLT_SEL bits are 11 */
	REGULATOR_LINEAR_RANGE(675000, 0x0, 0x3, 100000),
	REGULATOR_LINEAR_RANGE(1025000, 0x4, 0x5, 50000),
	REGULATOR_LINEAR_RANGE(1175000, 0x6, 0x7, 150000),
};

static const unsigned int bd71847_buck3_volt_range_sel[] = {
	0x0, 0x0, 0x0, 0x40, 0x80, 0x80, 0x80
};

static const struct linear_range bd71847_buck4_volts[] = {
	REGULATOR_LINEAR_RANGE(3000000, 0x00, 0x03, 100000),
	REGULATOR_LINEAR_RANGE(2600000, 0x00, 0x03, 100000),
};

static const unsigned int bd71847_buck4_volt_range_sel[] = { 0x0, 0x40 };

/*
 * BUCK6
 * 3.0V to 3.3V (step 100mV)
 */
static const struct linear_range bd71837_buck6_volts[] = {
	REGULATOR_LINEAR_RANGE(3000000, 0x00, 0x03, 100000),
};

/*
 * BD71837 BUCK7
 * BD71847 BUCK5
 * 000 = 1.605V
 * 001 = 1.695V
 * 010 = 1.755V
 * 011 = 1.8V (Initial)
 * 100 = 1.845V
 * 101 = 1.905V
 * 110 = 1.95V
 * 111 = 1.995V
 */
static const unsigned int bd718xx_3rd_nodvs_buck_volts[] = {
	1605000, 1695000, 1755000, 1800000, 1845000, 1905000, 1950000, 1995000
};

/*
 * BUCK8
 * 0.8V to 1.40V (step 10mV)
 */
static const struct linear_range bd718xx_4th_nodvs_buck_volts[] = {
	REGULATOR_LINEAR_RANGE(800000, 0x00, 0x3C, 10000),
};

/*
 * LDO1
 * 3.0 to 3.3V (100mV step)
 */
static const struct linear_range bd718xx_ldo1_volts[] = {
	REGULATOR_LINEAR_RANGE(3000000, 0x00, 0x03, 100000),
	REGULATOR_LINEAR_RANGE(1600000, 0x00, 0x03, 100000),
};

static const unsigned int bd718xx_ldo1_volt_range_sel[] = { 0x0, 0x20 };

/*
 * LDO2
 * 0.8 or 0.9V
 */
static const unsigned int ldo_2_volts[] = {
	900000, 800000
};

/*
 * LDO3
 * 1.8 to 3.3V (100mV step)
 */
static const struct linear_range bd718xx_ldo3_volts[] = {
	REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
};

/*
 * LDO4
 * 0.9 to 1.8V (100mV step)
 */
static const struct linear_range bd718xx_ldo4_volts[] = {
	REGULATOR_LINEAR_RANGE(900000, 0x00, 0x09, 100000),
};

/*
 * LDO5 for BD71837
 * 1.8 to 3.3V (100mV step)
 */
static const struct linear_range bd71837_ldo5_volts[] = {
	REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
};

/*
 * LDO5 for BD71837
 * 1.8 to 3.3V (100mV step)
 */
static const struct linear_range bd71847_ldo5_volts[] = {
	REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
	REGULATOR_LINEAR_RANGE(800000, 0x00, 0x0F, 100000),
};

static const unsigned int bd71847_ldo5_volt_range_sel[] = { 0x0, 0x20 };

/*
 * LDO6
 * 0.9 to 1.8V (100mV step)
 */
static const struct linear_range bd718xx_ldo6_volts[] = {
	REGULATOR_LINEAR_RANGE(900000, 0x00, 0x09, 100000),
};

/*
 * LDO7
 * 1.8 to 3.3V (100mV step)
 */
static const struct linear_range bd71837_ldo7_volts[] = {
	REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
};

struct reg_init {
	unsigned int reg;
	unsigned int mask;
	unsigned int val;
};
struct bd718xx_regulator_data {
	struct regulator_desc desc;
	const struct rohm_dvs_config dvs;
	const struct reg_init init;
	const struct reg_init *additional_inits;
	int additional_init_amnt;
};

/*
 * There is a HW quirk in BD71837. The shutdown sequence timings for
 * bucks/LDOs which are controlled via register interface are changed.
 * At PMIC poweroff the voltage for BUCK6/7 is cut immediately at the
 * beginning of shut-down sequence. As bucks 6 and 7 are parent
 * supplies for LDO5 and LDO6 - this causes LDO5/6 voltage
 * monitoring to errorneously detect under voltage and force PMIC to
 * emergency state instead of poweroff. In order to avoid this we
 * disable voltage monitoring for LDO5 and LDO6
 */
static const struct reg_init bd71837_ldo5_inits[] = {
	{
		.reg = BD718XX_REG_MVRFLTMASK2,
		.mask = BD718XX_LDO5_VRMON80,
		.val = BD718XX_LDO5_VRMON80,
	},
};

static const struct reg_init bd71837_ldo6_inits[] = {
	{
		.reg = BD718XX_REG_MVRFLTMASK2,
		.mask = BD718XX_LDO6_VRMON80,
		.val = BD718XX_LDO6_VRMON80,
	},
};

static int buck_set_hw_dvs_levels(struct device_node *np,
			    const struct regulator_desc *desc,
			    struct regulator_config *cfg)
{
	struct bd718xx_regulator_data *data;

	data = container_of(desc, struct bd718xx_regulator_data, desc);

	return rohm_regulator_set_dvs_levels(&data->dvs, np, desc, cfg->regmap);
}

static const struct bd718xx_regulator_data bd71847_regulators[] = {
	{
		.desc = {
			.name = "buck1",
			.of_match = of_match_ptr("BUCK1"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_BUCK1,
			.ops = &bd718xx_dvs_buck_regulator_ops,
			.type = REGULATOR_VOLTAGE,
			.n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM,
			.linear_ranges = bd718xx_dvs_buck_volts,
			.n_linear_ranges =
				ARRAY_SIZE(bd718xx_dvs_buck_volts),
			.vsel_reg = BD718XX_REG_BUCK1_VOLT_RUN,
			.vsel_mask = DVS_BUCK_RUN_MASK,
			.enable_reg = BD718XX_REG_BUCK1_CTRL,
			.enable_mask = BD718XX_BUCK_EN,
			.owner = THIS_MODULE,
			.of_parse_cb = buck_set_hw_dvs_levels,
		},
		.dvs = {
			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
				     ROHM_DVS_LEVEL_SUSPEND,
			.run_reg = BD718XX_REG_BUCK1_VOLT_RUN,
			.run_mask = DVS_BUCK_RUN_MASK,
			.idle_reg = BD718XX_REG_BUCK1_VOLT_IDLE,
			.idle_mask = DVS_BUCK_RUN_MASK,
			.suspend_reg = BD718XX_REG_BUCK1_VOLT_SUSP,
			.suspend_mask = DVS_BUCK_RUN_MASK,
		},
		.init = {
			.reg = BD718XX_REG_BUCK1_CTRL,
			.mask = BD718XX_BUCK_SEL,
			.val = BD718XX_BUCK_SEL,
		},
	},
	{
		.desc = {
			.name = "buck2",
			.of_match = of_match_ptr("BUCK2"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_BUCK2,
			.ops = &bd718xx_dvs_buck_regulator_ops,
			.type = REGULATOR_VOLTAGE,
			.n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM,
			.linear_ranges = bd718xx_dvs_buck_volts,
			.n_linear_ranges = ARRAY_SIZE(bd718xx_dvs_buck_volts),
			.vsel_reg = BD718XX_REG_BUCK2_VOLT_RUN,
			.vsel_mask = DVS_BUCK_RUN_MASK,
			.enable_reg = BD718XX_REG_BUCK2_CTRL,
			.enable_mask = BD718XX_BUCK_EN,
			.owner = THIS_MODULE,
			.of_parse_cb = buck_set_hw_dvs_levels,
		},
		.dvs = {
			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE,
			.run_reg = BD718XX_REG_BUCK2_VOLT_RUN,
			.run_mask = DVS_BUCK_RUN_MASK,
			.idle_reg = BD718XX_REG_BUCK2_VOLT_IDLE,
			.idle_mask = DVS_BUCK_RUN_MASK,
		},
		.init = {
			.reg = BD718XX_REG_BUCK2_CTRL,
			.mask = BD718XX_BUCK_SEL,
			.val = BD718XX_BUCK_SEL,
		},
	},
	{
		.desc = {
			.name = "buck3",
			.of_match = of_match_ptr("BUCK3"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_BUCK3,
			.ops = &bd718xx_pickable_range_buck_ops,
			.type = REGULATOR_VOLTAGE,
			.n_voltages = BD71847_BUCK3_VOLTAGE_NUM,
			.linear_ranges = bd71847_buck3_volts,
			.n_linear_ranges =
				ARRAY_SIZE(bd71847_buck3_volts),
			.vsel_reg = BD718XX_REG_1ST_NODVS_BUCK_VOLT,
			.vsel_mask = BD718XX_1ST_NODVS_BUCK_MASK,
			.vsel_range_reg = BD718XX_REG_1ST_NODVS_BUCK_VOLT,
			.vsel_range_mask = BD71847_BUCK3_RANGE_MASK,
			.linear_range_selectors = bd71847_buck3_volt_range_sel,
			.enable_reg = BD718XX_REG_1ST_NODVS_BUCK_CTRL,
			.enable_mask = BD718XX_BUCK_EN,
			.owner = THIS_MODULE,
		},
		.init = {
			.reg = BD718XX_REG_1ST_NODVS_BUCK_CTRL,
			.mask = BD718XX_BUCK_SEL,
			.val = BD718XX_BUCK_SEL,
		},
	},
	{
		.desc = {
			.name = "buck4",
			.of_match = of_match_ptr("BUCK4"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_BUCK4,
			.ops = &bd718xx_pickable_range_buck_ops,
			.type = REGULATOR_VOLTAGE,
			.n_voltages = BD71847_BUCK4_VOLTAGE_NUM,
			.linear_ranges = bd71847_buck4_volts,
			.n_linear_ranges =
				ARRAY_SIZE(bd71847_buck4_volts),
			.enable_reg = BD718XX_REG_2ND_NODVS_BUCK_CTRL,
			.vsel_reg = BD718XX_REG_2ND_NODVS_BUCK_VOLT,
			.vsel_mask = BD71847_BUCK4_MASK,
			.vsel_range_reg = BD718XX_REG_2ND_NODVS_BUCK_VOLT,
			.vsel_range_mask = BD71847_BUCK4_RANGE_MASK,
			.linear_range_selectors = bd71847_buck4_volt_range_sel,
			.enable_mask = BD718XX_BUCK_EN,
			.owner = THIS_MODULE,
		},
		.init = {
			.reg = BD718XX_REG_2ND_NODVS_BUCK_CTRL,
			.mask = BD718XX_BUCK_SEL,
			.val = BD718XX_BUCK_SEL,
		},
	},
	{
		.desc = {
			.name = "buck5",
			.of_match = of_match_ptr("BUCK5"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_BUCK5,
			.ops = &bd718xx_buck_regulator_nolinear_ops,
			.type = REGULATOR_VOLTAGE,
			.volt_table = &bd718xx_3rd_nodvs_buck_volts[0],
			.n_voltages = ARRAY_SIZE(bd718xx_3rd_nodvs_buck_volts),
			.vsel_reg = BD718XX_REG_3RD_NODVS_BUCK_VOLT,
			.vsel_mask = BD718XX_3RD_NODVS_BUCK_MASK,
			.enable_reg = BD718XX_REG_3RD_NODVS_BUCK_CTRL,
			.enable_mask = BD718XX_BUCK_EN,
			.owner = THIS_MODULE,
		},
		.init = {
			.reg = BD718XX_REG_3RD_NODVS_BUCK_CTRL,
			.mask = BD718XX_BUCK_SEL,
			.val = BD718XX_BUCK_SEL,
		},
	},
	{
		.desc = {
			.name = "buck6",
			.of_match = of_match_ptr("BUCK6"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_BUCK6,
			.ops = &bd718xx_buck_regulator_ops,
			.type = REGULATOR_VOLTAGE,
			.n_voltages = BD718XX_4TH_NODVS_BUCK_VOLTAGE_NUM,
			.linear_ranges = bd718xx_4th_nodvs_buck_volts,
			.n_linear_ranges =
				ARRAY_SIZE(bd718xx_4th_nodvs_buck_volts),
			.vsel_reg = BD718XX_REG_4TH_NODVS_BUCK_VOLT,
			.vsel_mask = BD718XX_4TH_NODVS_BUCK_MASK,
			.enable_reg = BD718XX_REG_4TH_NODVS_BUCK_CTRL,
			.enable_mask = BD718XX_BUCK_EN,
			.owner = THIS_MODULE,
		},
		.init = {
			.reg = BD718XX_REG_4TH_NODVS_BUCK_CTRL,
			.mask = BD718XX_BUCK_SEL,
			.val = BD718XX_BUCK_SEL,
		},
	},
	{
		.desc = {
			.name = "ldo1",
			.of_match = of_match_ptr("LDO1"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_LDO1,
			.ops = &bd718xx_pickable_range_ldo_ops,
			.type = REGULATOR_VOLTAGE,
			.n_voltages = BD718XX_LDO1_VOLTAGE_NUM,
			.linear_ranges = bd718xx_ldo1_volts,
			.n_linear_ranges = ARRAY_SIZE(bd718xx_ldo1_volts),
			.vsel_reg = BD718XX_REG_LDO1_VOLT,
			.vsel_mask = BD718XX_LDO1_MASK,
			.vsel_range_reg = BD718XX_REG_LDO1_VOLT,
			.vsel_range_mask = BD718XX_LDO1_RANGE_MASK,
			.linear_range_selectors = bd718xx_ldo1_volt_range_sel,
			.enable_reg = BD718XX_REG_LDO1_VOLT,
			.enable_mask = BD718XX_LDO_EN,
			.owner = THIS_MODULE,
		},
		.init = {
			.reg = BD718XX_REG_LDO1_VOLT,
			.mask = BD718XX_LDO_SEL,
			.val = BD718XX_LDO_SEL,
		},
	},
	{
		.desc = {
			.name = "ldo2",
			.of_match = of_match_ptr("LDO2"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_LDO2,
			.ops = &bd718xx_ldo_regulator_nolinear_ops,
			.type = REGULATOR_VOLTAGE,
			.volt_table = &ldo_2_volts[0],
			.vsel_reg = BD718XX_REG_LDO2_VOLT,
			.vsel_mask = BD718XX_LDO2_MASK,
			.n_voltages = ARRAY_SIZE(ldo_2_volts),
			.enable_reg = BD718XX_REG_LDO2_VOLT,
			.enable_mask = BD718XX_LDO_EN,
			.owner = THIS_MODULE,
		},
		.init = {
			.reg = BD718XX_REG_LDO2_VOLT,
			.mask = BD718XX_LDO_SEL,
			.val = BD718XX_LDO_SEL,
		},
	},
	{
		.desc = {
			.name = "ldo3",
			.of_match = of_match_ptr("LDO3"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_LDO3,
			.ops = &bd718xx_ldo_regulator_ops,
			.type = REGULATOR_VOLTAGE,
			.n_voltages = BD718XX_LDO3_VOLTAGE_NUM,
			.linear_ranges = bd718xx_ldo3_volts,
			.n_linear_ranges = ARRAY_SIZE(bd718xx_ldo3_volts),
			.vsel_reg = BD718XX_REG_LDO3_VOLT,
			.vsel_mask = BD718XX_LDO3_MASK,
			.enable_reg = BD718XX_REG_LDO3_VOLT,
			.enable_mask = BD718XX_LDO_EN,
			.owner = THIS_MODULE,
		},
		.init = {
			.reg = BD718XX_REG_LDO3_VOLT,
			.mask = BD718XX_LDO_SEL,
			.val = BD718XX_LDO_SEL,
		},
	},
	{
		.desc = {
			.name = "ldo4",
			.of_match = of_match_ptr("LDO4"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_LDO4,
			.ops = &bd718xx_ldo_regulator_ops,
			.type = REGULATOR_VOLTAGE,
			.n_voltages = BD718XX_LDO4_VOLTAGE_NUM,
			.linear_ranges = bd718xx_ldo4_volts,
			.n_linear_ranges = ARRAY_SIZE(bd718xx_ldo4_volts),
			.vsel_reg = BD718XX_REG_LDO4_VOLT,
			.vsel_mask = BD718XX_LDO4_MASK,
			.enable_reg = BD718XX_REG_LDO4_VOLT,
			.enable_mask = BD718XX_LDO_EN,
			.owner = THIS_MODULE,
		},
		.init = {
			.reg = BD718XX_REG_LDO4_VOLT,
			.mask = BD718XX_LDO_SEL,
			.val = BD718XX_LDO_SEL,
		},
	},
	{
		.desc = {
			.name = "ldo5",
			.of_match = of_match_ptr("LDO5"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_LDO5,
			.ops = &bd718xx_pickable_range_ldo_ops,
			.type = REGULATOR_VOLTAGE,
			.n_voltages = BD71847_LDO5_VOLTAGE_NUM,
			.linear_ranges = bd71847_ldo5_volts,
			.n_linear_ranges = ARRAY_SIZE(bd71847_ldo5_volts),
			.vsel_reg = BD718XX_REG_LDO5_VOLT,
			.vsel_mask = BD71847_LDO5_MASK,
			.vsel_range_reg = BD718XX_REG_LDO5_VOLT,
			.vsel_range_mask = BD71847_LDO5_RANGE_MASK,
			.linear_range_selectors = bd71847_ldo5_volt_range_sel,
			.enable_reg = BD718XX_REG_LDO5_VOLT,
			.enable_mask = BD718XX_LDO_EN,
			.owner = THIS_MODULE,
		},
		.init = {
			.reg = BD718XX_REG_LDO5_VOLT,
			.mask = BD718XX_LDO_SEL,
			.val = BD718XX_LDO_SEL,
		},
	},
	{
		.desc = {
			.name = "ldo6",
			.of_match = of_match_ptr("LDO6"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_LDO6,
			.ops = &bd718xx_ldo_regulator_ops,
			.type = REGULATOR_VOLTAGE,
			.n_voltages = BD718XX_LDO6_VOLTAGE_NUM,
			.linear_ranges = bd718xx_ldo6_volts,
			.n_linear_ranges = ARRAY_SIZE(bd718xx_ldo6_volts),
			/* LDO6 is supplied by buck5 */
			.supply_name = "buck5",
			.vsel_reg = BD718XX_REG_LDO6_VOLT,
			.vsel_mask = BD718XX_LDO6_MASK,
			.enable_reg = BD718XX_REG_LDO6_VOLT,
			.enable_mask = BD718XX_LDO_EN,
			.owner = THIS_MODULE,
		},
		.init = {
			.reg = BD718XX_REG_LDO6_VOLT,
			.mask = BD718XX_LDO_SEL,
			.val = BD718XX_LDO_SEL,
		},
	},
};

static const struct bd718xx_regulator_data bd71837_regulators[] = {
	{
		.desc = {
			.name = "buck1",
			.of_match = of_match_ptr("BUCK1"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_BUCK1,
			.ops = &bd718xx_dvs_buck_regulator_ops,
			.type = REGULATOR_VOLTAGE,
			.n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM,
			.linear_ranges = bd718xx_dvs_buck_volts,
			.n_linear_ranges = ARRAY_SIZE(bd718xx_dvs_buck_volts),
			.vsel_reg = BD718XX_REG_BUCK1_VOLT_RUN,
			.vsel_mask = DVS_BUCK_RUN_MASK,
			.enable_reg = BD718XX_REG_BUCK1_CTRL,
			.enable_mask = BD718XX_BUCK_EN,
			.owner = THIS_MODULE,
			.of_parse_cb = buck_set_hw_dvs_levels,
		},
		.dvs = {
			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
				     ROHM_DVS_LEVEL_SUSPEND,
			.run_reg = BD718XX_REG_BUCK1_VOLT_RUN,
			.run_mask = DVS_BUCK_RUN_MASK,
			.idle_reg = BD718XX_REG_BUCK1_VOLT_IDLE,
			.idle_mask = DVS_BUCK_RUN_MASK,
			.suspend_reg = BD718XX_REG_BUCK1_VOLT_SUSP,
			.suspend_mask = DVS_BUCK_RUN_MASK,
		},
		.init = {
			.reg = BD718XX_REG_BUCK1_CTRL,
			.mask = BD718XX_BUCK_SEL,
			.val = BD718XX_BUCK_SEL,
		},
	},
	{
		.desc = {
			.name = "buck2",
			.of_match = of_match_ptr("BUCK2"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_BUCK2,
			.ops = &bd718xx_dvs_buck_regulator_ops,
			.type = REGULATOR_VOLTAGE,
			.n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM,
			.linear_ranges = bd718xx_dvs_buck_volts,
			.n_linear_ranges = ARRAY_SIZE(bd718xx_dvs_buck_volts),
			.vsel_reg = BD718XX_REG_BUCK2_VOLT_RUN,
			.vsel_mask = DVS_BUCK_RUN_MASK,
			.enable_reg = BD718XX_REG_BUCK2_CTRL,
			.enable_mask = BD718XX_BUCK_EN,
			.owner = THIS_MODULE,
			.of_parse_cb = buck_set_hw_dvs_levels,
		},
		.dvs = {
			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE,
			.run_reg = BD718XX_REG_BUCK2_VOLT_RUN,
			.run_mask = DVS_BUCK_RUN_MASK,
			.idle_reg = BD718XX_REG_BUCK2_VOLT_IDLE,
			.idle_mask = DVS_BUCK_RUN_MASK,
		},
		.init = {
			.reg = BD718XX_REG_BUCK2_CTRL,
			.mask = BD718XX_BUCK_SEL,
			.val = BD718XX_BUCK_SEL,
		},
	},
	{
		.desc = {
			.name = "buck3",
			.of_match = of_match_ptr("BUCK3"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_BUCK3,
			.ops = &bd718xx_dvs_buck_regulator_ops,
			.type = REGULATOR_VOLTAGE,
			.n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM,
			.linear_ranges = bd718xx_dvs_buck_volts,
			.n_linear_ranges = ARRAY_SIZE(bd718xx_dvs_buck_volts),
			.vsel_reg = BD71837_REG_BUCK3_VOLT_RUN,
			.vsel_mask = DVS_BUCK_RUN_MASK,
			.enable_reg = BD71837_REG_BUCK3_CTRL,
			.enable_mask = BD718XX_BUCK_EN,
			.owner = THIS_MODULE,
			.of_parse_cb = buck_set_hw_dvs_levels,
		},
		.dvs = {
			.level_map = ROHM_DVS_LEVEL_RUN,
			.run_reg = BD71837_REG_BUCK3_VOLT_RUN,
			.run_mask = DVS_BUCK_RUN_MASK,
		},
		.init = {
			.reg = BD71837_REG_BUCK3_CTRL,
			.mask = BD718XX_BUCK_SEL,
			.val = BD718XX_BUCK_SEL,
		},
	},
	{
		.desc = {
			.name = "buck4",
			.of_match = of_match_ptr("BUCK4"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_BUCK4,
			.ops = &bd718xx_dvs_buck_regulator_ops,
			.type = REGULATOR_VOLTAGE,
			.n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM,
			.linear_ranges = bd718xx_dvs_buck_volts,
			.n_linear_ranges = ARRAY_SIZE(bd718xx_dvs_buck_volts),
			.vsel_reg = BD71837_REG_BUCK4_VOLT_RUN,
			.vsel_mask = DVS_BUCK_RUN_MASK,
			.enable_reg = BD71837_REG_BUCK4_CTRL,
			.enable_mask = BD718XX_BUCK_EN,
			.owner = THIS_MODULE,
			.of_parse_cb = buck_set_hw_dvs_levels,
		},
		.dvs = {
			.level_map = ROHM_DVS_LEVEL_RUN,
			.run_reg = BD71837_REG_BUCK4_VOLT_RUN,
			.run_mask = DVS_BUCK_RUN_MASK,
		},
		.init = {
			.reg = BD71837_REG_BUCK4_CTRL,
			.mask = BD718XX_BUCK_SEL,
			.val = BD718XX_BUCK_SEL,
		},
	},
	{
		.desc = {
			.name = "buck5",
			.of_match = of_match_ptr("BUCK5"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_BUCK5,
			.ops = &bd71837_pickable_range_buck_ops,
			.type = REGULATOR_VOLTAGE,
			.n_voltages = BD71837_BUCK5_VOLTAGE_NUM,
			.linear_ranges = bd71837_buck5_volts,
			.n_linear_ranges =
				ARRAY_SIZE(bd71837_buck5_volts),
			.vsel_reg = BD718XX_REG_1ST_NODVS_BUCK_VOLT,
			.vsel_mask = BD71837_BUCK5_MASK,
			.vsel_range_reg = BD718XX_REG_1ST_NODVS_BUCK_VOLT,
			.vsel_range_mask = BD71837_BUCK5_RANGE_MASK,
			.linear_range_selectors = bd71837_buck5_volt_range_sel,
			.enable_reg = BD718XX_REG_1ST_NODVS_BUCK_CTRL,
			.enable_mask = BD718XX_BUCK_EN,
			.owner = THIS_MODULE,
		},
		.init = {
			.reg = BD718XX_REG_1ST_NODVS_BUCK_CTRL,
			.mask = BD718XX_BUCK_SEL,
			.val = BD718XX_BUCK_SEL,
		},
	},
	{
		.desc = {
			.name = "buck6",
			.of_match = of_match_ptr("BUCK6"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_BUCK6,
			.ops = &bd71837_buck_regulator_ops,
			.type = REGULATOR_VOLTAGE,
			.n_voltages = BD71837_BUCK6_VOLTAGE_NUM,
			.linear_ranges = bd71837_buck6_volts,
			.n_linear_ranges =
				ARRAY_SIZE(bd71837_buck6_volts),
			.vsel_reg = BD718XX_REG_2ND_NODVS_BUCK_VOLT,
			.vsel_mask = BD71837_BUCK6_MASK,
			.enable_reg = BD718XX_REG_2ND_NODVS_BUCK_CTRL,
			.enable_mask = BD718XX_BUCK_EN,
			.owner = THIS_MODULE,
		},
		.init = {
			.reg = BD718XX_REG_2ND_NODVS_BUCK_CTRL,
			.mask = BD718XX_BUCK_SEL,
			.val = BD718XX_BUCK_SEL,
		},
	},
	{
		.desc = {
			.name = "buck7",
			.of_match = of_match_ptr("BUCK7"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_BUCK7,
			.ops = &bd71837_buck_regulator_nolinear_ops,
			.type = REGULATOR_VOLTAGE,
			.volt_table = &bd718xx_3rd_nodvs_buck_volts[0],
			.n_voltages = ARRAY_SIZE(bd718xx_3rd_nodvs_buck_volts),
			.vsel_reg = BD718XX_REG_3RD_NODVS_BUCK_VOLT,
			.vsel_mask = BD718XX_3RD_NODVS_BUCK_MASK,
			.enable_reg = BD718XX_REG_3RD_NODVS_BUCK_CTRL,
			.enable_mask = BD718XX_BUCK_EN,
			.owner = THIS_MODULE,
		},
		.init = {
			.reg = BD718XX_REG_3RD_NODVS_BUCK_CTRL,
			.mask = BD718XX_BUCK_SEL,
			.val = BD718XX_BUCK_SEL,
		},
	},
	{
		.desc = {
			.name = "buck8",
			.of_match = of_match_ptr("BUCK8"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_BUCK8,
			.ops = &bd71837_buck_regulator_ops,
			.type = REGULATOR_VOLTAGE,
			.n_voltages = BD718XX_4TH_NODVS_BUCK_VOLTAGE_NUM,
			.linear_ranges = bd718xx_4th_nodvs_buck_volts,
			.n_linear_ranges =
				ARRAY_SIZE(bd718xx_4th_nodvs_buck_volts),
			.vsel_reg = BD718XX_REG_4TH_NODVS_BUCK_VOLT,
			.vsel_mask = BD718XX_4TH_NODVS_BUCK_MASK,
			.enable_reg = BD718XX_REG_4TH_NODVS_BUCK_CTRL,
			.enable_mask = BD718XX_BUCK_EN,
			.owner = THIS_MODULE,
		},
		.init = {
			.reg = BD718XX_REG_4TH_NODVS_BUCK_CTRL,
			.mask = BD718XX_BUCK_SEL,
			.val = BD718XX_BUCK_SEL,
		},
	},
	{
		.desc = {
			.name = "ldo1",
			.of_match = of_match_ptr("LDO1"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_LDO1,
			.ops = &bd71837_pickable_range_ldo_ops,
			.type = REGULATOR_VOLTAGE,
			.n_voltages = BD718XX_LDO1_VOLTAGE_NUM,
			.linear_ranges = bd718xx_ldo1_volts,
			.n_linear_ranges = ARRAY_SIZE(bd718xx_ldo1_volts),
			.vsel_reg = BD718XX_REG_LDO1_VOLT,
			.vsel_mask = BD718XX_LDO1_MASK,
			.vsel_range_reg = BD718XX_REG_LDO1_VOLT,
			.vsel_range_mask = BD718XX_LDO1_RANGE_MASK,
			.linear_range_selectors = bd718xx_ldo1_volt_range_sel,
			.enable_reg = BD718XX_REG_LDO1_VOLT,
			.enable_mask = BD718XX_LDO_EN,
			.owner = THIS_MODULE,
		},
		.init = {
			.reg = BD718XX_REG_LDO1_VOLT,
			.mask = BD718XX_LDO_SEL,
			.val = BD718XX_LDO_SEL,
		},
	},
	{
		.desc = {
			.name = "ldo2",
			.of_match = of_match_ptr("LDO2"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_LDO2,
			.ops = &bd71837_ldo_regulator_nolinear_ops,
			.type = REGULATOR_VOLTAGE,
			.volt_table = &ldo_2_volts[0],
			.vsel_reg = BD718XX_REG_LDO2_VOLT,
			.vsel_mask = BD718XX_LDO2_MASK,
			.n_voltages = ARRAY_SIZE(ldo_2_volts),
			.enable_reg = BD718XX_REG_LDO2_VOLT,
			.enable_mask = BD718XX_LDO_EN,
			.owner = THIS_MODULE,
		},
		.init = {
			.reg = BD718XX_REG_LDO2_VOLT,
			.mask = BD718XX_LDO_SEL,
			.val = BD718XX_LDO_SEL,
		},
	},
	{
		.desc = {
			.name = "ldo3",
			.of_match = of_match_ptr("LDO3"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_LDO3,
			.ops = &bd71837_ldo_regulator_ops,
			.type = REGULATOR_VOLTAGE,
			.n_voltages = BD718XX_LDO3_VOLTAGE_NUM,
			.linear_ranges = bd718xx_ldo3_volts,
			.n_linear_ranges = ARRAY_SIZE(bd718xx_ldo3_volts),
			.vsel_reg = BD718XX_REG_LDO3_VOLT,
			.vsel_mask = BD718XX_LDO3_MASK,
			.enable_reg = BD718XX_REG_LDO3_VOLT,
			.enable_mask = BD718XX_LDO_EN,
			.owner = THIS_MODULE,
		},
		.init = {
			.reg = BD718XX_REG_LDO3_VOLT,
			.mask = BD718XX_LDO_SEL,
			.val = BD718XX_LDO_SEL,
		},
	},
	{
		.desc = {
			.name = "ldo4",
			.of_match = of_match_ptr("LDO4"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_LDO4,
			.ops = &bd71837_ldo_regulator_ops,
			.type = REGULATOR_VOLTAGE,
			.n_voltages = BD718XX_LDO4_VOLTAGE_NUM,
			.linear_ranges = bd718xx_ldo4_volts,
			.n_linear_ranges = ARRAY_SIZE(bd718xx_ldo4_volts),
			.vsel_reg = BD718XX_REG_LDO4_VOLT,
			.vsel_mask = BD718XX_LDO4_MASK,
			.enable_reg = BD718XX_REG_LDO4_VOLT,
			.enable_mask = BD718XX_LDO_EN,
			.owner = THIS_MODULE,
		},
		.init = {
			.reg = BD718XX_REG_LDO4_VOLT,
			.mask = BD718XX_LDO_SEL,
			.val = BD718XX_LDO_SEL,
		},
	},
	{
		.desc = {
			.name = "ldo5",
			.of_match = of_match_ptr("LDO5"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_LDO5,
			.ops = &bd71837_ldo_regulator_ops,
			.type = REGULATOR_VOLTAGE,
			.n_voltages = BD71837_LDO5_VOLTAGE_NUM,
			.linear_ranges = bd71837_ldo5_volts,
			.n_linear_ranges = ARRAY_SIZE(bd71837_ldo5_volts),
			/* LDO5 is supplied by buck6 */
			.supply_name = "buck6",
			.vsel_reg = BD718XX_REG_LDO5_VOLT,
			.vsel_mask = BD71837_LDO5_MASK,
			.enable_reg = BD718XX_REG_LDO5_VOLT,
			.enable_mask = BD718XX_LDO_EN,
			.owner = THIS_MODULE,
		},
		.init = {
			.reg = BD718XX_REG_LDO5_VOLT,
			.mask = BD718XX_LDO_SEL,
			.val = BD718XX_LDO_SEL,
		},
		.additional_inits = bd71837_ldo5_inits,
		.additional_init_amnt = ARRAY_SIZE(bd71837_ldo5_inits),
	},
	{
		.desc = {
			.name = "ldo6",
			.of_match = of_match_ptr("LDO6"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_LDO6,
			.ops = &bd71837_ldo_regulator_ops,
			.type = REGULATOR_VOLTAGE,
			.n_voltages = BD718XX_LDO6_VOLTAGE_NUM,
			.linear_ranges = bd718xx_ldo6_volts,
			.n_linear_ranges = ARRAY_SIZE(bd718xx_ldo6_volts),
			/* LDO6 is supplied by buck7 */
			.supply_name = "buck7",
			.vsel_reg = BD718XX_REG_LDO6_VOLT,
			.vsel_mask = BD718XX_LDO6_MASK,
			.enable_reg = BD718XX_REG_LDO6_VOLT,
			.enable_mask = BD718XX_LDO_EN,
			.owner = THIS_MODULE,
		},
		.init = {
			.reg = BD718XX_REG_LDO6_VOLT,
			.mask = BD718XX_LDO_SEL,
			.val = BD718XX_LDO_SEL,
		},
		.additional_inits = bd71837_ldo6_inits,
		.additional_init_amnt = ARRAY_SIZE(bd71837_ldo6_inits),
	},
	{
		.desc = {
			.name = "ldo7",
			.of_match = of_match_ptr("LDO7"),
			.regulators_node = of_match_ptr("regulators"),
			.id = BD718XX_LDO7,
			.ops = &bd71837_ldo_regulator_ops,
			.type = REGULATOR_VOLTAGE,
			.n_voltages = BD71837_LDO7_VOLTAGE_NUM,
			.linear_ranges = bd71837_ldo7_volts,
			.n_linear_ranges = ARRAY_SIZE(bd71837_ldo7_volts),
			.vsel_reg = BD71837_REG_LDO7_VOLT,
			.vsel_mask = BD71837_LDO7_MASK,
			.enable_reg = BD71837_REG_LDO7_VOLT,
			.enable_mask = BD718XX_LDO_EN,
			.owner = THIS_MODULE,
		},
		.init = {
			.reg = BD71837_REG_LDO7_VOLT,
			.mask = BD718XX_LDO_SEL,
			.val = BD718XX_LDO_SEL,
		},
	},
};

static int bd718xx_probe(struct platform_device *pdev)
{
	struct bd718xx *mfd;
	struct regulator_config config = { 0 };
	int i, j, err;
	bool use_snvs;
	const struct bd718xx_regulator_data *reg_data;
	unsigned int num_reg_data;
	enum rohm_chip_type chip = platform_get_device_id(pdev)->driver_data;

	mfd = dev_get_drvdata(pdev->dev.parent);
	if (!mfd) {
		dev_err(&pdev->dev, "No MFD driver data\n");
		err = -EINVAL;
		goto err;
	}

	switch (chip) {
	case ROHM_CHIP_TYPE_BD71837:
		reg_data = bd71837_regulators;
		num_reg_data = ARRAY_SIZE(bd71837_regulators);
		break;
	case ROHM_CHIP_TYPE_BD71847:
		reg_data = bd71847_regulators;
		num_reg_data = ARRAY_SIZE(bd71847_regulators);
		break;
	default:
		dev_err(&pdev->dev, "Unsupported chip type\n");
		err = -EINVAL;
		goto err;
	}

	/* Register LOCK release */
	err = regmap_update_bits(mfd->chip.regmap, BD718XX_REG_REGLOCK,
				 (REGLOCK_PWRSEQ | REGLOCK_VREG), 0);
	if (err) {
		dev_err(&pdev->dev, "Failed to unlock PMIC (%d)\n", err);
		goto err;
	} else {
		dev_dbg(&pdev->dev, "Unlocked lock register 0x%x\n",
			BD718XX_REG_REGLOCK);
	}

	use_snvs = of_property_read_bool(pdev->dev.parent->of_node,
					 "rohm,reset-snvs-powered");

	/*
	 * Change the next stage from poweroff to be READY instead of SNVS
	 * for all reset types because OTP loading at READY will clear SEL
	 * bit allowing HW defaults for power rails to be used
	 */
	if (!use_snvs) {
		err = regmap_update_bits(mfd->chip.regmap,
					 BD718XX_REG_TRANS_COND1,
					 BD718XX_ON_REQ_POWEROFF_MASK |
					 BD718XX_SWRESET_POWEROFF_MASK |
					 BD718XX_WDOG_POWEROFF_MASK |
					 BD718XX_KEY_L_POWEROFF_MASK,
					 BD718XX_POWOFF_TO_RDY);
		if (err) {
			dev_err(&pdev->dev, "Failed to change reset target\n");
			goto err;
		} else {
			dev_dbg(&pdev->dev,
				"Changed all resets from SVNS to READY\n");
		}
	}

	for (i = 0; i < num_reg_data; i++) {

		const struct regulator_desc *desc;
		struct regulator_dev *rdev;
		const struct bd718xx_regulator_data *r;

		r = &reg_data[i];
		desc = &r->desc;

		config.dev = pdev->dev.parent;
		config.regmap = mfd->chip.regmap;

		rdev = devm_regulator_register(&pdev->dev, desc, &config);
		if (IS_ERR(rdev)) {
			dev_err(&pdev->dev,
				"failed to register %s regulator\n",
				desc->name);
			err = PTR_ERR(rdev);
			goto err;
		}

		/*
		 * Regulator register gets the regulator constraints and
		 * applies them (set_machine_constraints). This should have
		 * turned the control register(s) to correct values and we
		 * can now switch the control from PMIC state machine to the
		 * register interface
		 *
		 * At poweroff transition PMIC HW disables EN bit for
		 * regulators but leaves SEL bit untouched. So if state
		 * transition from POWEROFF is done to SNVS - then all power
		 * rails controlled by SW (having SEL bit set) stay disabled
		 * as EN is cleared. This will result boot failure if any
		 * crucial systems are powered by these rails. We don't
		 * enable SW control for crucial regulators if snvs state is
		 * used
		 */
		if (!use_snvs || !rdev->constraints->always_on ||
		    !rdev->constraints->boot_on) {
			err = regmap_update_bits(mfd->chip.regmap, r->init.reg,
						 r->init.mask, r->init.val);
			if (err) {
				dev_err(&pdev->dev,
					"Failed to take control for (%s)\n",
					desc->name);
				goto err;
			}
		}
		for (j = 0; j < r->additional_init_amnt; j++) {
			err = regmap_update_bits(mfd->chip.regmap,
						 r->additional_inits[j].reg,
						 r->additional_inits[j].mask,
						 r->additional_inits[j].val);
			if (err) {
				dev_err(&pdev->dev,
					"Buck (%s) initialization failed\n",
					desc->name);
				goto err;
			}
		}
	}

err:
	return err;
}

static const struct platform_device_id bd718x7_pmic_id[] = {
	{ "bd71837-pmic", ROHM_CHIP_TYPE_BD71837 },
	{ "bd71847-pmic", ROHM_CHIP_TYPE_BD71847 },
	{ },
};
MODULE_DEVICE_TABLE(platform, bd718x7_pmic_id);

static struct platform_driver bd718xx_regulator = {
	.driver = {
		.name = "bd718xx-pmic",
	},
	.probe = bd718xx_probe,
	.id_table = bd718x7_pmic_id,
};

module_platform_driver(bd718xx_regulator);

MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
MODULE_DESCRIPTION("BD71837/BD71847 voltage regulator driver");
MODULE_LICENSE("GPL");
MODULE_ALIAS("platform:bd718xx-pmic");