Contributors: 12
Author Tokens Token Proportion Commits Commit Proportion
Kevin Hilman 720 75.55% 1 2.86%
Paul Walmsley 120 12.59% 16 45.71%
Tero Kristo 55 5.77% 4 11.43%
Tony Lindgren 40 4.20% 6 17.14%
Rajendra Nayak 4 0.42% 1 2.86%
Stephen Boyd 3 0.31% 1 2.86%
Dave Gerlach 3 0.31% 1 2.86%
Thomas Gleixner 2 0.21% 1 2.86%
Peter 'p2' De Schrijver 2 0.21% 1 2.86%
Jouni Högander 2 0.21% 1 2.86%
Nico Pitre 1 0.10% 1 2.86%
Santosh Shilimkar 1 0.10% 1 2.86%
Total 953 35 


// SPDX-License-Identifier: GPL-2.0-only
/*
 * OMAP2 Power Management Routines
 *
 * Copyright (C) 2005 Texas Instruments, Inc.
 * Copyright (C) 2006-2008 Nokia Corporation
 *
 * Written by:
 * Richard Woodruff <r-woodruff2@ti.com>
 * Tony Lindgren
 * Juha Yrjola
 * Amit Kucheria <amit.kucheria@nokia.com>
 * Igor Stoppa <igor.stoppa@nokia.com>
 *
 * Based on pm.c for omap1
 */

#include <linux/cpu_pm.h>
#include <linux/suspend.h>
#include <linux/sched.h>
#include <linux/proc_fs.h>
#include <linux/interrupt.h>
#include <linux/sysfs.h>
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/clk.h>
#include <linux/clk-provider.h>
#include <linux/irq.h>
#include <linux/time.h>

#include <asm/fncpy.h>

#include <asm/mach/time.h>
#include <asm/mach/irq.h>
#include <asm/mach-types.h>
#include <asm/system_misc.h>

#include <linux/omap-dma.h>

#include "soc.h"
#include "common.h"
#include "clock.h"
#include "prm2xxx.h"
#include "prm-regbits-24xx.h"
#include "cm2xxx.h"
#include "cm-regbits-24xx.h"
#include "sdrc.h"
#include "sram.h"
#include "pm.h"
#include "control.h"
#include "powerdomain.h"
#include "clockdomain.h"

static void (*omap2_sram_suspend)(u32 dllctrl, void __iomem *sdrc_dlla_ctrl,
				  void __iomem *sdrc_power);

static struct powerdomain *mpu_pwrdm, *core_pwrdm;
static struct clockdomain *dsp_clkdm, *mpu_clkdm, *wkup_clkdm, *gfx_clkdm;

static struct clk *osc_ck, *emul_ck;

static int omap2_enter_full_retention(void)
{
	u32 l;

	/* There is 1 reference hold for all children of the oscillator
	 * clock, the following will remove it. If no one else uses the
	 * oscillator itself it will be disabled if/when we enter retention
	 * mode.
	 */
	clk_disable(osc_ck);

	/* Clear old wake-up events */
	/* REVISIT: These write to reserved bits? */
	omap_prm_clear_mod_irqs(CORE_MOD, PM_WKST1, ~0);
	omap_prm_clear_mod_irqs(CORE_MOD, OMAP24XX_PM_WKST2, ~0);
	omap_prm_clear_mod_irqs(WKUP_MOD, PM_WKST, ~0);

	pwrdm_set_next_pwrst(core_pwrdm, PWRDM_POWER_RET);
	pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_RET);

	/* Workaround to kill USB */
	l = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0) | OMAP24XX_USBSTANDBYCTRL;
	omap_ctrl_writel(l, OMAP2_CONTROL_DEVCONF0);

	/* One last check for pending IRQs to avoid extra latency due
	 * to sleeping unnecessarily. */
	if (omap_irq_pending())
		goto no_sleep;

	/* Jump to SRAM suspend code */
	omap2_sram_suspend(sdrc_read_reg(SDRC_DLLA_CTRL),
			   OMAP_SDRC_REGADDR(SDRC_DLLA_CTRL),
			   OMAP_SDRC_REGADDR(SDRC_POWER));

no_sleep:
	clk_enable(osc_ck);

	/* clear CORE wake-up events */
	omap_prm_clear_mod_irqs(CORE_MOD, PM_WKST1, ~0);
	omap_prm_clear_mod_irqs(CORE_MOD, OMAP24XX_PM_WKST2, ~0);

	/* wakeup domain events - bit 1: GPT1, bit5 GPIO */
	omap_prm_clear_mod_irqs(WKUP_MOD, PM_WKST, 0x4 | 0x1);

	/* MPU domain wake events */
	omap_prm_clear_mod_irqs(OCP_MOD, OMAP2_PRCM_IRQSTATUS_MPU_OFFSET, 0x1);

	omap_prm_clear_mod_irqs(OCP_MOD, OMAP2_PRCM_IRQSTATUS_MPU_OFFSET, 0x20);

	pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_ON);
	pwrdm_set_next_pwrst(core_pwrdm, PWRDM_POWER_ON);

	return 0;
}

static int sti_console_enabled;

static int omap2_allow_mpu_retention(void)
{
	if (!omap2xxx_cm_mpu_retention_allowed())
		return 0;
	if (sti_console_enabled)
		return 0;

	return 1;
}

static void omap2_enter_mpu_retention(void)
{
	const int zero = 0;

	/* The peripherals seem not to be able to wake up the MPU when
	 * it is in retention mode. */
	if (omap2_allow_mpu_retention()) {
		/* REVISIT: These write to reserved bits? */
		omap_prm_clear_mod_irqs(CORE_MOD, PM_WKST1, ~0);
		omap_prm_clear_mod_irqs(CORE_MOD, OMAP24XX_PM_WKST2, ~0);
		omap_prm_clear_mod_irqs(WKUP_MOD, PM_WKST, ~0);

		/* Try to enter MPU retention */
		pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_RET);

	} else {
		/* Block MPU retention */
		pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_ON);
	}

	/* WFI */
	asm("mcr p15, 0, %0, c7, c0, 4" : : "r" (zero) : "memory", "cc");

	pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_ON);
}

static int omap2_can_sleep(void)
{
	if (omap2xxx_cm_fclks_active())
		return 0;
	if (__clk_is_enabled(osc_ck))
		return 0;

	return 1;
}

static void omap2_pm_idle(void)
{
	int error;

	if (omap_irq_pending())
		return;

	error = cpu_cluster_pm_enter();
	if (error || !omap2_can_sleep()) {
		omap2_enter_mpu_retention();
		goto out_cpu_cluster_pm;
	}

	omap2_enter_full_retention();

out_cpu_cluster_pm:
	cpu_cluster_pm_exit();
}

static void __init prcm_setup_regs(void)
{
	int i, num_mem_banks;
	struct powerdomain *pwrdm;

	/*
	 * Enable autoidle
	 * XXX This should be handled by hwmod code or PRCM init code
	 */
	omap2_prm_write_mod_reg(OMAP24XX_AUTOIDLE_MASK, OCP_MOD,
			  OMAP2_PRCM_SYSCONFIG_OFFSET);

	/*
	 * Set CORE powerdomain memory banks to retain their contents
	 * during RETENTION
	 */
	num_mem_banks = pwrdm_get_mem_bank_count(core_pwrdm);
	for (i = 0; i < num_mem_banks; i++)
		pwrdm_set_mem_retst(core_pwrdm, i, PWRDM_POWER_RET);

	pwrdm_set_logic_retst(core_pwrdm, PWRDM_POWER_RET);

	pwrdm_set_logic_retst(mpu_pwrdm, PWRDM_POWER_RET);

	/* Force-power down DSP, GFX powerdomains */

	pwrdm = clkdm_get_pwrdm(dsp_clkdm);
	pwrdm_set_next_pwrst(pwrdm, PWRDM_POWER_OFF);

	pwrdm = clkdm_get_pwrdm(gfx_clkdm);
	pwrdm_set_next_pwrst(pwrdm, PWRDM_POWER_OFF);

	/* Enable hardware-supervised idle for all clkdms */
	clkdm_for_each(omap_pm_clkdms_setup, NULL);
	clkdm_add_wkdep(mpu_clkdm, wkup_clkdm);

	omap_common_suspend_init(omap2_enter_full_retention);

	/* REVISIT: Configure number of 32 kHz clock cycles for sys_clk
	 * stabilisation */
	omap2_prm_write_mod_reg(15 << OMAP_SETUP_TIME_SHIFT, OMAP24XX_GR_MOD,
				OMAP2_PRCM_CLKSSETUP_OFFSET);

	/* Configure automatic voltage transition */
	omap2_prm_write_mod_reg(2 << OMAP_SETUP_TIME_SHIFT, OMAP24XX_GR_MOD,
				OMAP2_PRCM_VOLTSETUP_OFFSET);
	omap2_prm_write_mod_reg(OMAP24XX_AUTO_EXTVOLT_MASK |
				(0x1 << OMAP24XX_SETOFF_LEVEL_SHIFT) |
				OMAP24XX_MEMRETCTRL_MASK |
				(0x1 << OMAP24XX_SETRET_LEVEL_SHIFT) |
				(0x0 << OMAP24XX_VOLT_LEVEL_SHIFT),
				OMAP24XX_GR_MOD, OMAP2_PRCM_VOLTCTRL_OFFSET);

	/* Enable wake-up events */
	omap2_prm_write_mod_reg(OMAP24XX_EN_GPIOS_MASK | OMAP24XX_EN_GPT1_MASK,
				WKUP_MOD, PM_WKEN);

	/* Enable SYS_CLKEN control when all domains idle */
	omap2_prm_set_mod_reg_bits(OMAP_AUTOEXTCLKMODE_MASK, OMAP24XX_GR_MOD,
				   OMAP2_PRCM_CLKSRC_CTRL_OFFSET);
}

int __init omap2_pm_init(void)
{
	u32 l;

	printk(KERN_INFO "Power Management for OMAP2 initializing\n");
	l = omap2_prm_read_mod_reg(OCP_MOD, OMAP2_PRCM_REVISION_OFFSET);
	printk(KERN_INFO "PRCM revision %d.%d\n", (l >> 4) & 0x0f, l & 0x0f);

	/* Look up important powerdomains */

	mpu_pwrdm = pwrdm_lookup("mpu_pwrdm");
	if (!mpu_pwrdm)
		pr_err("PM: mpu_pwrdm not found\n");

	core_pwrdm = pwrdm_lookup("core_pwrdm");
	if (!core_pwrdm)
		pr_err("PM: core_pwrdm not found\n");

	/* Look up important clockdomains */

	mpu_clkdm = clkdm_lookup("mpu_clkdm");
	if (!mpu_clkdm)
		pr_err("PM: mpu_clkdm not found\n");

	wkup_clkdm = clkdm_lookup("wkup_clkdm");
	if (!wkup_clkdm)
		pr_err("PM: wkup_clkdm not found\n");

	dsp_clkdm = clkdm_lookup("dsp_clkdm");
	if (!dsp_clkdm)
		pr_err("PM: dsp_clkdm not found\n");

	gfx_clkdm = clkdm_lookup("gfx_clkdm");
	if (!gfx_clkdm)
		pr_err("PM: gfx_clkdm not found\n");


	osc_ck = clk_get(NULL, "osc_ck");
	if (IS_ERR(osc_ck)) {
		printk(KERN_ERR "could not get osc_ck\n");
		return -ENODEV;
	}

	if (cpu_is_omap242x()) {
		emul_ck = clk_get(NULL, "emul_ck");
		if (IS_ERR(emul_ck)) {
			printk(KERN_ERR "could not get emul_ck\n");
			clk_put(osc_ck);
			return -ENODEV;
		}
	}

	prcm_setup_regs();

	/*
	 * We copy the assembler sleep/wakeup routines to SRAM.
	 * These routines need to be in SRAM as that's the only
	 * memory the MPU can see when it wakes up after the entire
	 * chip enters idle.
	 */
	omap2_sram_suspend = omap_sram_push(omap24xx_cpu_suspend,
					    omap24xx_cpu_suspend_sz);

	arm_pm_idle = omap2_pm_idle;

	return 0;
}