Author | Tokens | Token Proportion | Commits | Commit Proportion |
---|---|---|---|---|
Neil Armstrong | 980 | 59.54% | 1 | 5.56% |
Lokesh Vutla | 283 | 17.19% | 4 | 22.22% |
David Rivshin | 173 | 10.51% | 5 | 27.78% |
J Keerthy | 100 | 6.08% | 1 | 5.56% |
Uwe Kleine-König | 74 | 4.50% | 3 | 16.67% |
Ivaylo Dimitrov | 33 | 2.00% | 1 | 5.56% |
Thomas Gleixner | 1 | 0.06% | 1 | 5.56% |
Alexander A. Klimov | 1 | 0.06% | 1 | 5.56% |
Lee Jones | 1 | 0.06% | 1 | 5.56% |
Total | 1646 | 18 |
// SPDX-License-Identifier: GPL-2.0-only /* * Copyright (c) 2015 Neil Armstrong <narmstrong@baylibre.com> * Copyright (c) 2014 Joachim Eastwood <manabian@gmail.com> * Copyright (c) 2012 NeilBrown <neilb@suse.de> * Heavily based on earlier code which is: * Copyright (c) 2010 Grant Erickson <marathon96@gmail.com> * * Also based on pwm-samsung.c * * Description: * This file is the core OMAP support for the generic, Linux * PWM driver / controller, using the OMAP's dual-mode timers * with a timer counter that goes up. When it overflows it gets * reloaded with the load value and the pwm output goes up. * When counter matches with match register, the output goes down. * Reference Manual: https://www.ti.com/lit/ug/spruh73q/spruh73q.pdf * * Limitations: * - When PWM is stopped, timer counter gets stopped immediately. This * doesn't allow the current PWM period to complete and stops abruptly. * - When PWM is running and changing both duty cycle and period, * we cannot prevent in software that the output might produce * a period with mixed settings. Especially when period/duty_cyle * is updated while the pwm pin is high, current pwm period/duty_cycle * can get updated as below based on the current timer counter: * - period for current cycle = current_period + new period * - duty_cycle for current period = current period + new duty_cycle. * - PWM OMAP DM timer cannot change the polarity when pwm is active. When * user requests a change in polarity when in active state: * - PWM is stopped abruptly(without completing the current cycle) * - Polarity is changed * - A fresh cycle is started. */ #include <linux/clk.h> #include <linux/err.h> #include <linux/kernel.h> #include <linux/module.h> #include <linux/mutex.h> #include <linux/of.h> #include <linux/of_platform.h> #include <clocksource/timer-ti-dm.h> #include <linux/platform_data/dmtimer-omap.h> #include <linux/platform_device.h> #include <linux/pm_runtime.h> #include <linux/pwm.h> #include <linux/slab.h> #include <linux/time.h> #define DM_TIMER_LOAD_MIN 0xfffffffe #define DM_TIMER_MAX 0xffffffff /** * struct pwm_omap_dmtimer_chip - Structure representing a pwm chip * corresponding to omap dmtimer. * @chip: PWM chip structure representing PWM controller * @mutex: Mutex to protect pwm apply state * @dm_timer: Pointer to omap dm timer. * @pdata: Pointer to omap dm timer ops. * @dm_timer_pdev: Pointer to omap dm timer platform device */ struct pwm_omap_dmtimer_chip { struct pwm_chip chip; /* Mutex to protect pwm apply state */ struct mutex mutex; struct omap_dm_timer *dm_timer; const struct omap_dm_timer_ops *pdata; struct platform_device *dm_timer_pdev; }; static inline struct pwm_omap_dmtimer_chip * to_pwm_omap_dmtimer_chip(struct pwm_chip *chip) { return container_of(chip, struct pwm_omap_dmtimer_chip, chip); } /** * pwm_omap_dmtimer_get_clock_cycles() - Get clock cycles in a time frame * @clk_rate: pwm timer clock rate * @ns: time frame in nano seconds. * * Return number of clock cycles in a given period(ins ns). */ static u32 pwm_omap_dmtimer_get_clock_cycles(unsigned long clk_rate, int ns) { return DIV_ROUND_CLOSEST_ULL((u64)clk_rate * ns, NSEC_PER_SEC); } /** * pwm_omap_dmtimer_start() - Start the pwm omap dm timer in pwm mode * @omap: Pointer to pwm omap dm timer chip */ static void pwm_omap_dmtimer_start(struct pwm_omap_dmtimer_chip *omap) { /* * According to OMAP 4 TRM section 22.2.4.10 the counter should be * started at 0xFFFFFFFE when overflow and match is used to ensure * that the PWM line is toggled on the first event. * * Note that omap_dm_timer_enable/disable is for register access and * not the timer counter itself. */ omap->pdata->enable(omap->dm_timer); omap->pdata->write_counter(omap->dm_timer, DM_TIMER_LOAD_MIN); omap->pdata->disable(omap->dm_timer); omap->pdata->start(omap->dm_timer); } /** * pwm_omap_dmtimer_is_enabled() - Detect if the pwm is enabled. * @omap: Pointer to pwm omap dm timer chip * * Return true if pwm is enabled else false. */ static bool pwm_omap_dmtimer_is_enabled(struct pwm_omap_dmtimer_chip *omap) { u32 status; status = omap->pdata->get_pwm_status(omap->dm_timer); return !!(status & OMAP_TIMER_CTRL_ST); } /** * pwm_omap_dmtimer_polarity() - Detect the polarity of pwm. * @omap: Pointer to pwm omap dm timer chip * * Return the polarity of pwm. */ static int pwm_omap_dmtimer_polarity(struct pwm_omap_dmtimer_chip *omap) { u32 status; status = omap->pdata->get_pwm_status(omap->dm_timer); return !!(status & OMAP_TIMER_CTRL_SCPWM); } /** * pwm_omap_dmtimer_config() - Update the configuration of pwm omap dm timer * @chip: Pointer to PWM controller * @pwm: Pointer to PWM channel * @duty_ns: New duty cycle in nano seconds * @period_ns: New period in nano seconds * * Return 0 if successfully changed the period/duty_cycle else appropriate * error. */ static int pwm_omap_dmtimer_config(struct pwm_chip *chip, struct pwm_device *pwm, int duty_ns, int period_ns) { struct pwm_omap_dmtimer_chip *omap = to_pwm_omap_dmtimer_chip(chip); u32 period_cycles, duty_cycles; u32 load_value, match_value; unsigned long clk_rate; struct clk *fclk; dev_dbg(chip->dev, "requested duty cycle: %d ns, period: %d ns\n", duty_ns, period_ns); if (duty_ns == pwm_get_duty_cycle(pwm) && period_ns == pwm_get_period(pwm)) return 0; fclk = omap->pdata->get_fclk(omap->dm_timer); if (!fclk) { dev_err(chip->dev, "invalid pmtimer fclk\n"); return -EINVAL; } clk_rate = clk_get_rate(fclk); if (!clk_rate) { dev_err(chip->dev, "invalid pmtimer fclk rate\n"); return -EINVAL; } dev_dbg(chip->dev, "clk rate: %luHz\n", clk_rate); /* * Calculate the appropriate load and match values based on the * specified period and duty cycle. The load value determines the * period time and the match value determines the duty time. * * The period lasts for (DM_TIMER_MAX-load_value+1) clock cycles. * Similarly, the active time lasts (match_value-load_value+1) cycles. * The non-active time is the remainder: (DM_TIMER_MAX-match_value) * clock cycles. * * NOTE: It is required that: load_value <= match_value < DM_TIMER_MAX * * References: * OMAP4430/60/70 TRM sections 22.2.4.10 and 22.2.4.11 * AM335x Sitara TRM sections 20.1.3.5 and 20.1.3.6 */ period_cycles = pwm_omap_dmtimer_get_clock_cycles(clk_rate, period_ns); duty_cycles = pwm_omap_dmtimer_get_clock_cycles(clk_rate, duty_ns); if (period_cycles < 2) { dev_info(chip->dev, "period %d ns too short for clock rate %lu Hz\n", period_ns, clk_rate); return -EINVAL; } if (duty_cycles < 1) { dev_dbg(chip->dev, "duty cycle %d ns is too short for clock rate %lu Hz\n", duty_ns, clk_rate); dev_dbg(chip->dev, "using minimum of 1 clock cycle\n"); duty_cycles = 1; } else if (duty_cycles >= period_cycles) { dev_dbg(chip->dev, "duty cycle %d ns is too long for period %d ns at clock rate %lu Hz\n", duty_ns, period_ns, clk_rate); dev_dbg(chip->dev, "using maximum of 1 clock cycle less than period\n"); duty_cycles = period_cycles - 1; } dev_dbg(chip->dev, "effective duty cycle: %lld ns, period: %lld ns\n", DIV_ROUND_CLOSEST_ULL((u64)NSEC_PER_SEC * duty_cycles, clk_rate), DIV_ROUND_CLOSEST_ULL((u64)NSEC_PER_SEC * period_cycles, clk_rate)); load_value = (DM_TIMER_MAX - period_cycles) + 1; match_value = load_value + duty_cycles - 1; omap->pdata->set_load(omap->dm_timer, load_value); omap->pdata->set_match(omap->dm_timer, true, match_value); dev_dbg(chip->dev, "load value: %#08x (%d), match value: %#08x (%d)\n", load_value, load_value, match_value, match_value); return 0; } /** * pwm_omap_dmtimer_set_polarity() - Changes the polarity of the pwm dm timer. * @chip: Pointer to PWM controller * @pwm: Pointer to PWM channel * @polarity: New pwm polarity to be set */ static void pwm_omap_dmtimer_set_polarity(struct pwm_chip *chip, struct pwm_device *pwm, enum pwm_polarity polarity) { struct pwm_omap_dmtimer_chip *omap = to_pwm_omap_dmtimer_chip(chip); bool enabled; /* Disable the PWM before changing the polarity. */ enabled = pwm_omap_dmtimer_is_enabled(omap); if (enabled) omap->pdata->stop(omap->dm_timer); omap->pdata->set_pwm(omap->dm_timer, polarity == PWM_POLARITY_INVERSED, true, OMAP_TIMER_TRIGGER_OVERFLOW_AND_COMPARE, true); if (enabled) pwm_omap_dmtimer_start(omap); } /** * pwm_omap_dmtimer_apply() - Changes the state of the pwm omap dm timer. * @chip: Pointer to PWM controller * @pwm: Pointer to PWM channel * @state: New state to apply * * Return 0 if successfully changed the state else appropriate error. */ static int pwm_omap_dmtimer_apply(struct pwm_chip *chip, struct pwm_device *pwm, const struct pwm_state *state) { struct pwm_omap_dmtimer_chip *omap = to_pwm_omap_dmtimer_chip(chip); int ret = 0; mutex_lock(&omap->mutex); if (pwm_omap_dmtimer_is_enabled(omap) && !state->enabled) { omap->pdata->stop(omap->dm_timer); goto unlock_mutex; } if (pwm_omap_dmtimer_polarity(omap) != state->polarity) pwm_omap_dmtimer_set_polarity(chip, pwm, state->polarity); ret = pwm_omap_dmtimer_config(chip, pwm, state->duty_cycle, state->period); if (ret) goto unlock_mutex; if (!pwm_omap_dmtimer_is_enabled(omap) && state->enabled) { omap->pdata->set_pwm(omap->dm_timer, state->polarity == PWM_POLARITY_INVERSED, true, OMAP_TIMER_TRIGGER_OVERFLOW_AND_COMPARE, true); pwm_omap_dmtimer_start(omap); } unlock_mutex: mutex_unlock(&omap->mutex); return ret; } static const struct pwm_ops pwm_omap_dmtimer_ops = { .apply = pwm_omap_dmtimer_apply, .owner = THIS_MODULE, }; static int pwm_omap_dmtimer_probe(struct platform_device *pdev) { struct device_node *np = pdev->dev.of_node; struct dmtimer_platform_data *timer_pdata; const struct omap_dm_timer_ops *pdata; struct platform_device *timer_pdev; struct pwm_omap_dmtimer_chip *omap; struct omap_dm_timer *dm_timer; struct device_node *timer; int ret = 0; u32 v; timer = of_parse_phandle(np, "ti,timers", 0); if (!timer) return -ENODEV; timer_pdev = of_find_device_by_node(timer); if (!timer_pdev) { dev_err(&pdev->dev, "Unable to find Timer pdev\n"); ret = -ENODEV; goto err_find_timer_pdev; } timer_pdata = dev_get_platdata(&timer_pdev->dev); if (!timer_pdata) { dev_dbg(&pdev->dev, "dmtimer pdata structure NULL, deferring probe\n"); ret = -EPROBE_DEFER; goto err_platdata; } pdata = timer_pdata->timer_ops; if (!pdata || !pdata->request_by_node || !pdata->free || !pdata->enable || !pdata->disable || !pdata->get_fclk || !pdata->start || !pdata->stop || !pdata->set_load || !pdata->set_match || !pdata->set_pwm || !pdata->get_pwm_status || !pdata->set_prescaler || !pdata->write_counter) { dev_err(&pdev->dev, "Incomplete dmtimer pdata structure\n"); ret = -EINVAL; goto err_platdata; } if (!of_get_property(timer, "ti,timer-pwm", NULL)) { dev_err(&pdev->dev, "Missing ti,timer-pwm capability\n"); ret = -ENODEV; goto err_timer_property; } dm_timer = pdata->request_by_node(timer); if (!dm_timer) { ret = -EPROBE_DEFER; goto err_request_timer; } omap = devm_kzalloc(&pdev->dev, sizeof(*omap), GFP_KERNEL); if (!omap) { ret = -ENOMEM; goto err_alloc_omap; } omap->pdata = pdata; omap->dm_timer = dm_timer; omap->dm_timer_pdev = timer_pdev; /* * Ensure that the timer is stopped before we allow PWM core to call * pwm_enable. */ if (pm_runtime_active(&omap->dm_timer_pdev->dev)) omap->pdata->stop(omap->dm_timer); if (!of_property_read_u32(pdev->dev.of_node, "ti,prescaler", &v)) omap->pdata->set_prescaler(omap->dm_timer, v); /* setup dmtimer clock source */ if (!of_property_read_u32(pdev->dev.of_node, "ti,clock-source", &v)) omap->pdata->set_source(omap->dm_timer, v); omap->chip.dev = &pdev->dev; omap->chip.ops = &pwm_omap_dmtimer_ops; omap->chip.npwm = 1; mutex_init(&omap->mutex); ret = pwmchip_add(&omap->chip); if (ret < 0) { dev_err(&pdev->dev, "failed to register PWM\n"); goto err_pwmchip_add; } of_node_put(timer); platform_set_drvdata(pdev, omap); return 0; err_pwmchip_add: /* * *omap is allocated using devm_kzalloc, * so no free necessary here */ err_alloc_omap: pdata->free(dm_timer); err_request_timer: err_timer_property: err_platdata: put_device(&timer_pdev->dev); err_find_timer_pdev: of_node_put(timer); return ret; } static int pwm_omap_dmtimer_remove(struct platform_device *pdev) { struct pwm_omap_dmtimer_chip *omap = platform_get_drvdata(pdev); pwmchip_remove(&omap->chip); if (pm_runtime_active(&omap->dm_timer_pdev->dev)) omap->pdata->stop(omap->dm_timer); omap->pdata->free(omap->dm_timer); put_device(&omap->dm_timer_pdev->dev); mutex_destroy(&omap->mutex); return 0; } static const struct of_device_id pwm_omap_dmtimer_of_match[] = { {.compatible = "ti,omap-dmtimer-pwm"}, {} }; MODULE_DEVICE_TABLE(of, pwm_omap_dmtimer_of_match); static struct platform_driver pwm_omap_dmtimer_driver = { .driver = { .name = "omap-dmtimer-pwm", .of_match_table = of_match_ptr(pwm_omap_dmtimer_of_match), }, .probe = pwm_omap_dmtimer_probe, .remove = pwm_omap_dmtimer_remove, }; module_platform_driver(pwm_omap_dmtimer_driver); MODULE_AUTHOR("Grant Erickson <marathon96@gmail.com>"); MODULE_AUTHOR("NeilBrown <neilb@suse.de>"); MODULE_AUTHOR("Neil Armstrong <narmstrong@baylibre.com>"); MODULE_LICENSE("GPL v2"); MODULE_DESCRIPTION("OMAP PWM Driver using Dual-mode Timers");
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.
Created with Cregit http://github.com/cregit/cregit
Version 2.0-RC1