Author | Tokens | Token Proportion | Commits | Commit Proportion |
---|---|---|---|---|
Marek Vašut | 2490 | 62.67% | 18 | 62.07% |
Jagan Teki | 1410 | 35.49% | 3 | 10.34% |
Jonathan Liu | 58 | 1.46% | 1 | 3.45% |
José Expósito | 6 | 0.15% | 1 | 3.45% |
Boris Brezillon | 3 | 0.08% | 1 | 3.45% |
Uwe Kleine-König | 2 | 0.05% | 2 | 6.90% |
Nícolas F. R. A. Prado | 2 | 0.05% | 1 | 3.45% |
Mark Brown | 1 | 0.03% | 1 | 3.45% |
Rob Herring | 1 | 0.03% | 1 | 3.45% |
Total | 3973 | 29 |
// SPDX-License-Identifier: GPL-2.0+ /* * Copyright (C) 2020 Amarula Solutions(India) * Author: Jagan Teki <jagan@amarulasolutions.com> */ #include <drm/drm_atomic_helper.h> #include <drm/drm_of.h> #include <drm/drm_print.h> #include <drm/drm_mipi_dsi.h> #include <linux/bitfield.h> #include <linux/bits.h> #include <linux/clk.h> #include <linux/delay.h> #include <linux/gpio/consumer.h> #include <linux/i2c.h> #include <linux/media-bus-format.h> #include <linux/module.h> #include <linux/of.h> #include <linux/regmap.h> #include <linux/regulator/consumer.h> #define VENDOR_ID 0x00 #define DEVICE_ID_H 0x01 #define DEVICE_ID_L 0x02 #define VERSION_ID 0x03 #define FIRMWARE_VERSION 0x08 #define CONFIG_FINISH 0x09 #define PD_CTRL(n) (0x0a + ((n) & 0x3)) /* 0..3 */ #define RST_CTRL(n) (0x0e + ((n) & 0x1)) /* 0..1 */ #define SYS_CTRL(n) (0x10 + ((n) & 0x7)) /* 0..4 */ #define SYS_CTRL_1_CLK_PHASE_MSK GENMASK(5, 4) #define CLK_PHASE_0 0 #define CLK_PHASE_1_4 1 #define CLK_PHASE_1_2 2 #define CLK_PHASE_3_4 3 #define RGB_DRV(n) (0x18 + ((n) & 0x3)) /* 0..3 */ #define RGB_DLY(n) (0x1c + ((n) & 0x1)) /* 0..1 */ #define RGB_TEST_CTRL 0x1e #define ATE_PLL_EN 0x1f #define HACTIVE_LI 0x20 #define VACTIVE_LI 0x21 #define VACTIVE_HACTIVE_HI 0x22 #define HFP_LI 0x23 #define HSYNC_LI 0x24 #define HBP_LI 0x25 #define HFP_HSW_HBP_HI 0x26 #define HFP_HSW_HBP_HI_HFP(n) (((n) & 0x300) >> 4) #define HFP_HSW_HBP_HI_HS(n) (((n) & 0x300) >> 6) #define HFP_HSW_HBP_HI_HBP(n) (((n) & 0x300) >> 8) #define VFP 0x27 #define VSYNC 0x28 #define VBP 0x29 #define BIST_POL 0x2a #define BIST_POL_BIST_MODE(n) (((n) & 0xf) << 4) #define BIST_POL_BIST_GEN BIT(3) #define BIST_POL_HSYNC_POL BIT(2) #define BIST_POL_VSYNC_POL BIT(1) #define BIST_POL_DE_POL BIT(0) #define BIST_RED 0x2b #define BIST_GREEN 0x2c #define BIST_BLUE 0x2d #define BIST_CHESS_X 0x2e #define BIST_CHESS_Y 0x2f #define BIST_CHESS_XY_H 0x30 #define BIST_FRAME_TIME_L 0x31 #define BIST_FRAME_TIME_H 0x32 #define FIFO_MAX_ADDR_LOW 0x33 #define SYNC_EVENT_DLY 0x34 #define HSW_MIN 0x35 #define HFP_MIN 0x36 #define LOGIC_RST_NUM 0x37 #define OSC_CTRL(n) (0x48 + ((n) & 0x7)) /* 0..5 */ #define BG_CTRL 0x4e #define LDO_PLL 0x4f #define PLL_CTRL(n) (0x50 + ((n) & 0xf)) /* 0..15 */ #define PLL_CTRL_6_EXTERNAL 0x90 #define PLL_CTRL_6_MIPI_CLK 0x92 #define PLL_CTRL_6_INTERNAL 0x93 #define PLL_REM(n) (0x60 + ((n) & 0x3)) /* 0..2 */ #define PLL_DIV(n) (0x63 + ((n) & 0x3)) /* 0..2 */ #define PLL_FRAC(n) (0x66 + ((n) & 0x3)) /* 0..2 */ #define PLL_INT(n) (0x69 + ((n) & 0x1)) /* 0..1 */ #define PLL_REF_DIV 0x6b #define PLL_REF_DIV_P(n) ((n) & 0xf) #define PLL_REF_DIV_Pe BIT(4) #define PLL_REF_DIV_S(n) (((n) & 0x7) << 5) #define PLL_SSC_P(n) (0x6c + ((n) & 0x3)) /* 0..2 */ #define PLL_SSC_STEP(n) (0x6f + ((n) & 0x3)) /* 0..2 */ #define PLL_SSC_OFFSET(n) (0x72 + ((n) & 0x3)) /* 0..3 */ #define GPIO_OEN 0x79 #define MIPI_CFG_PW 0x7a #define MIPI_CFG_PW_CONFIG_DSI 0xc1 #define MIPI_CFG_PW_CONFIG_I2C 0x3e #define GPIO_SEL(n) (0x7b + ((n) & 0x1)) /* 0..1 */ #define IRQ_SEL 0x7d #define DBG_SEL 0x7e #define DBG_SIGNAL 0x7f #define MIPI_ERR_VECTOR_L 0x80 #define MIPI_ERR_VECTOR_H 0x81 #define MIPI_ERR_VECTOR_EN_L 0x82 #define MIPI_ERR_VECTOR_EN_H 0x83 #define MIPI_MAX_SIZE_L 0x84 #define MIPI_MAX_SIZE_H 0x85 #define DSI_CTRL 0x86 #define DSI_CTRL_UNKNOWN 0x28 #define DSI_CTRL_DSI_LANES(n) ((n) & 0x3) #define MIPI_PN_SWAP 0x87 #define MIPI_PN_SWAP_CLK BIT(4) #define MIPI_PN_SWAP_D(n) BIT((n) & 0x3) #define MIPI_SOT_SYNC_BIT(n) (0x88 + ((n) & 0x1)) /* 0..1 */ #define MIPI_ULPS_CTRL 0x8a #define MIPI_CLK_CHK_VAR 0x8e #define MIPI_CLK_CHK_INI 0x8f #define MIPI_T_TERM_EN 0x90 #define MIPI_T_HS_SETTLE 0x91 #define MIPI_T_TA_SURE_PRE 0x92 #define MIPI_T_LPX_SET 0x94 #define MIPI_T_CLK_MISS 0x95 #define MIPI_INIT_TIME_L 0x96 #define MIPI_INIT_TIME_H 0x97 #define MIPI_T_CLK_TERM_EN 0x99 #define MIPI_T_CLK_SETTLE 0x9a #define MIPI_TO_HS_RX_L 0x9e #define MIPI_TO_HS_RX_H 0x9f #define MIPI_PHY(n) (0xa0 + ((n) & 0x7)) /* 0..5 */ #define MIPI_PD_RX 0xb0 #define MIPI_PD_TERM 0xb1 #define MIPI_PD_HSRX 0xb2 #define MIPI_PD_LPTX 0xb3 #define MIPI_PD_LPRX 0xb4 #define MIPI_PD_CK_LANE 0xb5 #define MIPI_FORCE_0 0xb6 #define MIPI_RST_CTRL 0xb7 #define MIPI_RST_NUM 0xb8 #define MIPI_DBG_SET(n) (0xc0 + ((n) & 0xf)) /* 0..9 */ #define MIPI_DBG_SEL 0xe0 #define MIPI_DBG_DATA 0xe1 #define MIPI_ATE_TEST_SEL 0xe2 #define MIPI_ATE_STATUS(n) (0xe3 + ((n) & 0x1)) /* 0..1 */ struct chipone { struct device *dev; struct regmap *regmap; struct i2c_client *client; struct drm_bridge bridge; struct drm_display_mode mode; struct drm_bridge *panel_bridge; struct mipi_dsi_device *dsi; struct gpio_desc *enable_gpio; struct regulator *vdd1; struct regulator *vdd2; struct regulator *vdd3; struct clk *refclk; unsigned long refclk_rate; bool interface_i2c; }; static const struct regmap_range chipone_dsi_readable_ranges[] = { regmap_reg_range(VENDOR_ID, VERSION_ID), regmap_reg_range(FIRMWARE_VERSION, PLL_SSC_OFFSET(3)), regmap_reg_range(GPIO_OEN, MIPI_ULPS_CTRL), regmap_reg_range(MIPI_CLK_CHK_VAR, MIPI_T_TA_SURE_PRE), regmap_reg_range(MIPI_T_LPX_SET, MIPI_INIT_TIME_H), regmap_reg_range(MIPI_T_CLK_TERM_EN, MIPI_T_CLK_SETTLE), regmap_reg_range(MIPI_TO_HS_RX_L, MIPI_PHY(5)), regmap_reg_range(MIPI_PD_RX, MIPI_RST_NUM), regmap_reg_range(MIPI_DBG_SET(0), MIPI_DBG_SET(9)), regmap_reg_range(MIPI_DBG_SEL, MIPI_ATE_STATUS(1)), }; static const struct regmap_access_table chipone_dsi_readable_table = { .yes_ranges = chipone_dsi_readable_ranges, .n_yes_ranges = ARRAY_SIZE(chipone_dsi_readable_ranges), }; static const struct regmap_range chipone_dsi_writeable_ranges[] = { regmap_reg_range(CONFIG_FINISH, PLL_SSC_OFFSET(3)), regmap_reg_range(GPIO_OEN, MIPI_ULPS_CTRL), regmap_reg_range(MIPI_CLK_CHK_VAR, MIPI_T_TA_SURE_PRE), regmap_reg_range(MIPI_T_LPX_SET, MIPI_INIT_TIME_H), regmap_reg_range(MIPI_T_CLK_TERM_EN, MIPI_T_CLK_SETTLE), regmap_reg_range(MIPI_TO_HS_RX_L, MIPI_PHY(5)), regmap_reg_range(MIPI_PD_RX, MIPI_RST_NUM), regmap_reg_range(MIPI_DBG_SET(0), MIPI_DBG_SET(9)), regmap_reg_range(MIPI_DBG_SEL, MIPI_ATE_STATUS(1)), }; static const struct regmap_access_table chipone_dsi_writeable_table = { .yes_ranges = chipone_dsi_writeable_ranges, .n_yes_ranges = ARRAY_SIZE(chipone_dsi_writeable_ranges), }; static const struct regmap_config chipone_regmap_config = { .reg_bits = 8, .val_bits = 8, .rd_table = &chipone_dsi_readable_table, .wr_table = &chipone_dsi_writeable_table, .cache_type = REGCACHE_MAPLE, .max_register = MIPI_ATE_STATUS(1), }; static int chipone_dsi_read(void *context, const void *reg, size_t reg_size, void *val, size_t val_size) { struct mipi_dsi_device *dsi = context; const u16 reg16 = (val_size << 8) | *(u8 *)reg; int ret; ret = mipi_dsi_generic_read(dsi, ®16, 2, val, val_size); return ret == val_size ? 0 : -EINVAL; } static int chipone_dsi_write(void *context, const void *data, size_t count) { struct mipi_dsi_device *dsi = context; return mipi_dsi_generic_write(dsi, data, 2); } static const struct regmap_bus chipone_dsi_regmap_bus = { .read = chipone_dsi_read, .write = chipone_dsi_write, .reg_format_endian_default = REGMAP_ENDIAN_NATIVE, .val_format_endian_default = REGMAP_ENDIAN_NATIVE, }; static inline struct chipone *bridge_to_chipone(struct drm_bridge *bridge) { return container_of(bridge, struct chipone, bridge); } static void chipone_readb(struct chipone *icn, u8 reg, u8 *val) { int ret, pval; ret = regmap_read(icn->regmap, reg, &pval); *val = ret ? 0 : pval & 0xff; } static int chipone_writeb(struct chipone *icn, u8 reg, u8 val) { return regmap_write(icn->regmap, reg, val); } static void chipone_configure_pll(struct chipone *icn, const struct drm_display_mode *mode) { unsigned int best_p = 0, best_m = 0, best_s = 0; unsigned int mode_clock = mode->clock * 1000; unsigned int delta, min_delta = 0xffffffff; unsigned int freq_p, freq_s, freq_out; unsigned int p_min, p_max; unsigned int p, m, s; unsigned int fin; bool best_p_pot; u8 ref_div; /* * DSI byte clock frequency (input into PLL) is calculated as: * DSI_CLK = HS clock / 4 * * DPI pixel clock frequency (output from PLL) is mode clock. * * The chip contains fractional PLL which works as follows: * DPI_CLK = ((DSI_CLK / P) * M) / S * P is pre-divider, register PLL_REF_DIV[3:0] is 1:n divider * register PLL_REF_DIV[4] is extra 1:2 divider * M is integer multiplier, register PLL_INT(0) is multiplier * S is post-divider, register PLL_REF_DIV[7:5] is 2^(n+1) divider * * It seems the PLL input clock after applying P pre-divider have * to be lower than 20 MHz. */ if (icn->refclk) fin = icn->refclk_rate; else fin = icn->dsi->hs_rate / 4; /* in Hz */ /* Minimum value of P predivider for PLL input in 5..20 MHz */ p_min = clamp(DIV_ROUND_UP(fin, 20000000), 1U, 31U); p_max = clamp(fin / 5000000, 1U, 31U); for (p = p_min; p < p_max; p++) { /* PLL_REF_DIV[4,3:0] */ if (p > 16 && p & 1) /* P > 16 uses extra /2 */ continue; freq_p = fin / p; if (freq_p == 0) /* Divider too high */ break; for (s = 0; s < 0x7; s++) { /* PLL_REF_DIV[7:5] */ freq_s = freq_p / BIT(s + 1); if (freq_s == 0) /* Divider too high */ break; m = mode_clock / freq_s; /* Multiplier is 8 bit */ if (m > 0xff) continue; /* Limit PLL VCO frequency to 1 GHz */ freq_out = (fin * m) / p; if (freq_out > 1000000000) continue; /* Apply post-divider */ freq_out /= BIT(s + 1); delta = abs(mode_clock - freq_out); if (delta < min_delta) { best_p = p; best_m = m; best_s = s; min_delta = delta; } } } best_p_pot = !(best_p & 1); dev_dbg(icn->dev, "PLL: P[3:0]=%d P[4]=2*%d M=%d S[7:5]=2^%d delta=%d => DSI f_in(%s)=%d Hz ; DPI f_out=%d Hz\n", best_p >> best_p_pot, best_p_pot, best_m, best_s + 1, min_delta, icn->refclk ? "EXT" : "DSI", fin, (fin * best_m) / (best_p << (best_s + 1))); ref_div = PLL_REF_DIV_P(best_p >> best_p_pot) | PLL_REF_DIV_S(best_s); if (best_p_pot) /* Prefer /2 pre-divider */ ref_div |= PLL_REF_DIV_Pe; /* Clock source selection either external clock or MIPI DSI clock lane */ chipone_writeb(icn, PLL_CTRL(6), icn->refclk ? PLL_CTRL_6_EXTERNAL : PLL_CTRL_6_MIPI_CLK); chipone_writeb(icn, PLL_REF_DIV, ref_div); chipone_writeb(icn, PLL_INT(0), best_m); } static void chipone_atomic_enable(struct drm_bridge *bridge, struct drm_bridge_state *old_bridge_state) { struct chipone *icn = bridge_to_chipone(bridge); struct drm_atomic_state *state = old_bridge_state->base.state; struct drm_display_mode *mode = &icn->mode; const struct drm_bridge_state *bridge_state; u16 hfp, hbp, hsync; u32 bus_flags; u8 pol, sys_ctrl_1, id[4]; chipone_readb(icn, VENDOR_ID, id); chipone_readb(icn, DEVICE_ID_H, id + 1); chipone_readb(icn, DEVICE_ID_L, id + 2); chipone_readb(icn, VERSION_ID, id + 3); dev_dbg(icn->dev, "Chip IDs: Vendor=0x%02x Device=0x%02x:0x%02x Version=0x%02x\n", id[0], id[1], id[2], id[3]); if (id[0] != 0xc1 || id[1] != 0x62 || id[2] != 0x11) { dev_dbg(icn->dev, "Invalid Chip IDs, aborting configuration\n"); return; } /* Get the DPI flags from the bridge state. */ bridge_state = drm_atomic_get_new_bridge_state(state, bridge); bus_flags = bridge_state->output_bus_cfg.flags; if (icn->interface_i2c) chipone_writeb(icn, MIPI_CFG_PW, MIPI_CFG_PW_CONFIG_I2C); else chipone_writeb(icn, MIPI_CFG_PW, MIPI_CFG_PW_CONFIG_DSI); chipone_writeb(icn, HACTIVE_LI, mode->hdisplay & 0xff); chipone_writeb(icn, VACTIVE_LI, mode->vdisplay & 0xff); /* * lsb nibble: 2nd nibble of hdisplay * msb nibble: 2nd nibble of vdisplay */ chipone_writeb(icn, VACTIVE_HACTIVE_HI, ((mode->hdisplay >> 8) & 0xf) | (((mode->vdisplay >> 8) & 0xf) << 4)); hfp = mode->hsync_start - mode->hdisplay; hsync = mode->hsync_end - mode->hsync_start; hbp = mode->htotal - mode->hsync_end; chipone_writeb(icn, HFP_LI, hfp & 0xff); chipone_writeb(icn, HSYNC_LI, hsync & 0xff); chipone_writeb(icn, HBP_LI, hbp & 0xff); /* Top two bits of Horizontal Front porch/Sync/Back porch */ chipone_writeb(icn, HFP_HSW_HBP_HI, HFP_HSW_HBP_HI_HFP(hfp) | HFP_HSW_HBP_HI_HS(hsync) | HFP_HSW_HBP_HI_HBP(hbp)); chipone_writeb(icn, VFP, mode->vsync_start - mode->vdisplay); chipone_writeb(icn, VSYNC, mode->vsync_end - mode->vsync_start); chipone_writeb(icn, VBP, mode->vtotal - mode->vsync_end); /* dsi specific sequence */ chipone_writeb(icn, SYNC_EVENT_DLY, 0x80); chipone_writeb(icn, HFP_MIN, hfp & 0xff); /* DSI data lane count */ chipone_writeb(icn, DSI_CTRL, DSI_CTRL_UNKNOWN | DSI_CTRL_DSI_LANES(icn->dsi->lanes - 1)); chipone_writeb(icn, MIPI_PD_CK_LANE, 0xa0); chipone_writeb(icn, PLL_CTRL(12), 0xff); chipone_writeb(icn, MIPI_PN_SWAP, 0x00); /* DPI HS/VS/DE polarity */ pol = ((mode->flags & DRM_MODE_FLAG_PHSYNC) ? BIST_POL_HSYNC_POL : 0) | ((mode->flags & DRM_MODE_FLAG_PVSYNC) ? BIST_POL_VSYNC_POL : 0) | ((bus_flags & DRM_BUS_FLAG_DE_HIGH) ? BIST_POL_DE_POL : 0); chipone_writeb(icn, BIST_POL, pol); /* Configure PLL settings */ chipone_configure_pll(icn, mode); chipone_writeb(icn, SYS_CTRL(0), 0x40); sys_ctrl_1 = 0x88; if (bus_flags & DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE) sys_ctrl_1 |= FIELD_PREP(SYS_CTRL_1_CLK_PHASE_MSK, CLK_PHASE_0); else sys_ctrl_1 |= FIELD_PREP(SYS_CTRL_1_CLK_PHASE_MSK, CLK_PHASE_1_2); chipone_writeb(icn, SYS_CTRL(1), sys_ctrl_1); /* icn6211 specific sequence */ chipone_writeb(icn, MIPI_FORCE_0, 0x20); chipone_writeb(icn, PLL_CTRL(1), 0x20); chipone_writeb(icn, CONFIG_FINISH, 0x10); usleep_range(10000, 11000); } static void chipone_atomic_pre_enable(struct drm_bridge *bridge, struct drm_bridge_state *old_bridge_state) { struct chipone *icn = bridge_to_chipone(bridge); int ret; if (icn->vdd1) { ret = regulator_enable(icn->vdd1); if (ret) DRM_DEV_ERROR(icn->dev, "failed to enable VDD1 regulator: %d\n", ret); } if (icn->vdd2) { ret = regulator_enable(icn->vdd2); if (ret) DRM_DEV_ERROR(icn->dev, "failed to enable VDD2 regulator: %d\n", ret); } if (icn->vdd3) { ret = regulator_enable(icn->vdd3); if (ret) DRM_DEV_ERROR(icn->dev, "failed to enable VDD3 regulator: %d\n", ret); } ret = clk_prepare_enable(icn->refclk); if (ret) DRM_DEV_ERROR(icn->dev, "failed to enable RECLK clock: %d\n", ret); gpiod_set_value(icn->enable_gpio, 1); usleep_range(10000, 11000); } static void chipone_atomic_post_disable(struct drm_bridge *bridge, struct drm_bridge_state *old_bridge_state) { struct chipone *icn = bridge_to_chipone(bridge); clk_disable_unprepare(icn->refclk); if (icn->vdd1) regulator_disable(icn->vdd1); if (icn->vdd2) regulator_disable(icn->vdd2); if (icn->vdd3) regulator_disable(icn->vdd3); gpiod_set_value(icn->enable_gpio, 0); } static void chipone_mode_set(struct drm_bridge *bridge, const struct drm_display_mode *mode, const struct drm_display_mode *adjusted_mode) { struct chipone *icn = bridge_to_chipone(bridge); drm_mode_copy(&icn->mode, adjusted_mode); }; static int chipone_dsi_attach(struct chipone *icn) { struct mipi_dsi_device *dsi = icn->dsi; struct device *dev = icn->dev; int dsi_lanes, ret; dsi_lanes = drm_of_get_data_lanes_count_ep(dev->of_node, 0, 0, 1, 4); /* * If the 'data-lanes' property does not exist in DT or is invalid, * default to previously hard-coded behavior, which was 4 data lanes. */ if (dsi_lanes < 0) icn->dsi->lanes = 4; else icn->dsi->lanes = dsi_lanes; dsi->format = MIPI_DSI_FMT_RGB888; dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST | MIPI_DSI_MODE_LPM | MIPI_DSI_MODE_NO_EOT_PACKET; dsi->hs_rate = 500000000; dsi->lp_rate = 16000000; ret = mipi_dsi_attach(dsi); if (ret < 0) dev_err(icn->dev, "failed to attach dsi\n"); return ret; } static int chipone_dsi_host_attach(struct chipone *icn) { struct device *dev = icn->dev; struct device_node *host_node; struct device_node *endpoint; struct mipi_dsi_device *dsi; struct mipi_dsi_host *host; int ret = 0; const struct mipi_dsi_device_info info = { .type = "chipone", .channel = 0, .node = NULL, }; endpoint = of_graph_get_endpoint_by_regs(dev->of_node, 0, 0); host_node = of_graph_get_remote_port_parent(endpoint); of_node_put(endpoint); if (!host_node) return -EINVAL; host = of_find_mipi_dsi_host_by_node(host_node); of_node_put(host_node); if (!host) return dev_err_probe(dev, -EPROBE_DEFER, "failed to find dsi host\n"); dsi = mipi_dsi_device_register_full(host, &info); if (IS_ERR(dsi)) { return dev_err_probe(dev, PTR_ERR(dsi), "failed to create dsi device\n"); } icn->dsi = dsi; ret = chipone_dsi_attach(icn); if (ret < 0) mipi_dsi_device_unregister(dsi); return ret; } static int chipone_attach(struct drm_bridge *bridge, enum drm_bridge_attach_flags flags) { struct chipone *icn = bridge_to_chipone(bridge); return drm_bridge_attach(bridge->encoder, icn->panel_bridge, bridge, flags); } #define MAX_INPUT_SEL_FORMATS 1 static u32 * chipone_atomic_get_input_bus_fmts(struct drm_bridge *bridge, struct drm_bridge_state *bridge_state, struct drm_crtc_state *crtc_state, struct drm_connector_state *conn_state, u32 output_fmt, unsigned int *num_input_fmts) { u32 *input_fmts; *num_input_fmts = 0; input_fmts = kcalloc(MAX_INPUT_SEL_FORMATS, sizeof(*input_fmts), GFP_KERNEL); if (!input_fmts) return NULL; /* This is the DSI-end bus format */ input_fmts[0] = MEDIA_BUS_FMT_RGB888_1X24; *num_input_fmts = 1; return input_fmts; } static const struct drm_bridge_funcs chipone_bridge_funcs = { .atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state, .atomic_destroy_state = drm_atomic_helper_bridge_destroy_state, .atomic_reset = drm_atomic_helper_bridge_reset, .atomic_pre_enable = chipone_atomic_pre_enable, .atomic_enable = chipone_atomic_enable, .atomic_post_disable = chipone_atomic_post_disable, .mode_set = chipone_mode_set, .attach = chipone_attach, .atomic_get_input_bus_fmts = chipone_atomic_get_input_bus_fmts, }; static int chipone_parse_dt(struct chipone *icn) { struct device *dev = icn->dev; int ret; icn->refclk = devm_clk_get_optional(dev, "refclk"); if (IS_ERR(icn->refclk)) { ret = PTR_ERR(icn->refclk); DRM_DEV_ERROR(dev, "failed to get REFCLK clock: %d\n", ret); return ret; } else if (icn->refclk) { icn->refclk_rate = clk_get_rate(icn->refclk); if (icn->refclk_rate < 10000000 || icn->refclk_rate > 154000000) { DRM_DEV_ERROR(dev, "REFCLK out of range: %ld Hz\n", icn->refclk_rate); return -EINVAL; } } icn->vdd1 = devm_regulator_get_optional(dev, "vdd1"); if (IS_ERR(icn->vdd1)) { ret = PTR_ERR(icn->vdd1); if (ret == -EPROBE_DEFER) return -EPROBE_DEFER; icn->vdd1 = NULL; DRM_DEV_DEBUG(dev, "failed to get VDD1 regulator: %d\n", ret); } icn->vdd2 = devm_regulator_get_optional(dev, "vdd2"); if (IS_ERR(icn->vdd2)) { ret = PTR_ERR(icn->vdd2); if (ret == -EPROBE_DEFER) return -EPROBE_DEFER; icn->vdd2 = NULL; DRM_DEV_DEBUG(dev, "failed to get VDD2 regulator: %d\n", ret); } icn->vdd3 = devm_regulator_get_optional(dev, "vdd3"); if (IS_ERR(icn->vdd3)) { ret = PTR_ERR(icn->vdd3); if (ret == -EPROBE_DEFER) return -EPROBE_DEFER; icn->vdd3 = NULL; DRM_DEV_DEBUG(dev, "failed to get VDD3 regulator: %d\n", ret); } icn->enable_gpio = devm_gpiod_get(dev, "enable", GPIOD_OUT_LOW); if (IS_ERR(icn->enable_gpio)) { DRM_DEV_ERROR(dev, "failed to get enable GPIO\n"); return PTR_ERR(icn->enable_gpio); } icn->panel_bridge = devm_drm_of_get_bridge(dev, dev->of_node, 1, 0); if (IS_ERR(icn->panel_bridge)) return PTR_ERR(icn->panel_bridge); return 0; } static int chipone_common_probe(struct device *dev, struct chipone **icnr) { struct chipone *icn; int ret; icn = devm_kzalloc(dev, sizeof(struct chipone), GFP_KERNEL); if (!icn) return -ENOMEM; icn->dev = dev; ret = chipone_parse_dt(icn); if (ret) return ret; icn->bridge.funcs = &chipone_bridge_funcs; icn->bridge.type = DRM_MODE_CONNECTOR_DPI; icn->bridge.of_node = dev->of_node; *icnr = icn; return ret; } static int chipone_dsi_probe(struct mipi_dsi_device *dsi) { struct device *dev = &dsi->dev; struct chipone *icn; int ret; ret = chipone_common_probe(dev, &icn); if (ret) return ret; icn->regmap = devm_regmap_init(dev, &chipone_dsi_regmap_bus, dsi, &chipone_regmap_config); if (IS_ERR(icn->regmap)) return PTR_ERR(icn->regmap); icn->interface_i2c = false; icn->dsi = dsi; mipi_dsi_set_drvdata(dsi, icn); drm_bridge_add(&icn->bridge); ret = chipone_dsi_attach(icn); if (ret) drm_bridge_remove(&icn->bridge); return ret; } static int chipone_i2c_probe(struct i2c_client *client) { struct device *dev = &client->dev; struct chipone *icn; int ret; ret = chipone_common_probe(dev, &icn); if (ret) return ret; icn->regmap = devm_regmap_init_i2c(client, &chipone_regmap_config); if (IS_ERR(icn->regmap)) return PTR_ERR(icn->regmap); icn->interface_i2c = true; icn->client = client; dev_set_drvdata(dev, icn); i2c_set_clientdata(client, icn); drm_bridge_add(&icn->bridge); return chipone_dsi_host_attach(icn); } static void chipone_dsi_remove(struct mipi_dsi_device *dsi) { struct chipone *icn = mipi_dsi_get_drvdata(dsi); mipi_dsi_detach(dsi); drm_bridge_remove(&icn->bridge); } static const struct of_device_id chipone_of_match[] = { { .compatible = "chipone,icn6211", }, { /* sentinel */ } }; MODULE_DEVICE_TABLE(of, chipone_of_match); static struct mipi_dsi_driver chipone_dsi_driver = { .probe = chipone_dsi_probe, .remove = chipone_dsi_remove, .driver = { .name = "chipone-icn6211", .of_match_table = chipone_of_match, }, }; static struct i2c_device_id chipone_i2c_id[] = { { "chipone,icn6211" }, {}, }; MODULE_DEVICE_TABLE(i2c, chipone_i2c_id); static struct i2c_driver chipone_i2c_driver = { .probe = chipone_i2c_probe, .id_table = chipone_i2c_id, .driver = { .name = "chipone-icn6211-i2c", .of_match_table = chipone_of_match, }, }; static int __init chipone_init(void) { if (IS_ENABLED(CONFIG_DRM_MIPI_DSI)) mipi_dsi_driver_register(&chipone_dsi_driver); return i2c_add_driver(&chipone_i2c_driver); } module_init(chipone_init); static void __exit chipone_exit(void) { i2c_del_driver(&chipone_i2c_driver); if (IS_ENABLED(CONFIG_DRM_MIPI_DSI)) mipi_dsi_driver_unregister(&chipone_dsi_driver); } module_exit(chipone_exit); MODULE_AUTHOR("Jagan Teki <jagan@amarulasolutions.com>"); MODULE_DESCRIPTION("Chipone ICN6211 MIPI-DSI to RGB Converter Bridge"); MODULE_LICENSE("GPL");
Information contained on this website is for historical information purposes only and does not indicate or represent copyright ownership.
Created with Cregit http://github.com/cregit/cregit
Version 2.0-RC1