Contributors: 14
Author Tokens Token Proportion Commits Commit Proportion
Octavian Purdila 93 32.18% 3 16.67%
Markus Pargmann 54 18.69% 2 11.11%
Srinivas Pandruvada 48 16.61% 1 5.56%
Hans de Goede 27 9.34% 2 11.11%
Jonathan Cameron 19 6.57% 1 5.56%
Stephan Gerhold 17 5.88% 1 5.56%
Linus Walleij 10 3.46% 1 5.56%
Laurentiu Palcu 6 2.08% 1 5.56%
Jeremy Cline 5 1.73% 1 5.56%
H. Nikolaus Schaller 4 1.38% 1 5.56%
Irina Tirdea 3 1.04% 1 5.56%
Uwe Kleine-König 1 0.35% 1 5.56%
Greg Kroah-Hartman 1 0.35% 1 5.56%
Vlad Dogaru 1 0.35% 1 5.56%
Total 289 18


/* SPDX-License-Identifier: GPL-2.0 */
#ifndef _BMC150_ACCEL_H_
#define _BMC150_ACCEL_H_

#include <linux/atomic.h>
#include <linux/iio/iio.h>
#include <linux/mutex.h>
#include <linux/regulator/consumer.h>
#include <linux/workqueue.h>

struct regmap;
struct i2c_client;
struct bmc150_accel_chip_info;
struct bmc150_accel_interrupt_info;

/*
 * We can often guess better than "UNKNOWN" based on the device IDs
 * but unfortunately this information is not always accurate. There are some
 * devices where ACPI firmware specifies an ID like "BMA250E" when the device
 * actually has a BMA222E. The driver attempts to detect those by reading the
 * chip ID from the registers but this information is not always enough either.
 *
 * Therefore, this enum should be only used when the chip ID detection is not
 * enough and we can be reasonably sure that the device IDs are reliable
 * in practice (e.g. for device tree platforms).
 */
enum bmc150_type {
	BOSCH_UNKNOWN,
	BOSCH_BMC156,
};

struct bmc150_accel_interrupt {
	const struct bmc150_accel_interrupt_info *info;
	atomic_t users;
};

struct bmc150_accel_trigger {
	struct bmc150_accel_data *data;
	struct iio_trigger *indio_trig;
	int (*setup)(struct bmc150_accel_trigger *t, bool state);
	int intr;
	bool enabled;
};

enum bmc150_accel_interrupt_id {
	BMC150_ACCEL_INT_DATA_READY,
	BMC150_ACCEL_INT_ANY_MOTION,
	BMC150_ACCEL_INT_WATERMARK,
	BMC150_ACCEL_INTERRUPTS,
};

enum bmc150_accel_trigger_id {
	BMC150_ACCEL_TRIGGER_DATA_READY,
	BMC150_ACCEL_TRIGGER_ANY_MOTION,
	BMC150_ACCEL_TRIGGERS,
};

struct bmc150_accel_data {
	struct regmap *regmap;
	struct regulator_bulk_data regulators[2];
	struct bmc150_accel_interrupt interrupts[BMC150_ACCEL_INTERRUPTS];
	struct bmc150_accel_trigger triggers[BMC150_ACCEL_TRIGGERS];
	struct mutex mutex;
	u8 fifo_mode, watermark;
	s16 buffer[8];
	/*
	 * Ensure there is sufficient space and correct alignment for
	 * the timestamp if enabled
	 */
	struct {
		__le16 channels[3];
		s64 ts __aligned(8);
	} scan;
	u8 bw_bits;
	u32 slope_dur;
	u32 slope_thres;
	u32 range;
	int ev_enable_state;
	int64_t timestamp, old_timestamp; /* Only used in hw fifo mode. */
	const struct bmc150_accel_chip_info *chip_info;
	enum bmc150_type type;
	struct i2c_client *second_device;
	void (*resume_callback)(struct device *dev);
	struct delayed_work resume_work;
	struct iio_mount_matrix orientation;
};

int bmc150_accel_core_probe(struct device *dev, struct regmap *regmap, int irq,
			    enum bmc150_type type, const char *name,
			    bool block_supported);
void bmc150_accel_core_remove(struct device *dev);
extern const struct dev_pm_ops bmc150_accel_pm_ops;
extern const struct regmap_config bmc150_regmap_conf;

#endif  /* _BMC150_ACCEL_H_ */